Test report

FCC ID: V5PD135

Test Report

Download: PDF
FCCID_4436336

FCC RF Test Report Report No. : FR980203C FCC RF Test Report APPLICANT : PAX Technology Limited EQUIPMENT : Secure Card Reader BRAND NAME : PAX MODEL NAME : D135 FCC ID : V5PD135 STANDARD : FCC Part 15 Subpart C §15.225 CLASSIFICATION : (DXX) Low Power Communication Device Transmitter The product was received on Aug. 02, 2019 and testing was completed on Aug. 27, 2019. We, Sporton International (ShenZhen) Inc., would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of Sporton International (ShenZhen) Inc., the test report shall not be reproduced except in full. Reviewed by: Derreck Chen / Supervisor Approved by: Eric Shih / Manager Sporton International (ShenZhen) Inc. 1/F, 2/F, Bldg 5, Shiling Industrial Zone, Xinwei Village, Xili, Nanshan, Shenzhen, 518055 People’s Republic of China Sporton International (Shenzhen) Inc. Page Number : 1 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C TABLE OF CONTENTS TABLE OF CONTENTS ...............................................................................................................................................2 REVISION HISTORY....................................................................................................................................................3 SUMMARY OF THE TEST RESULT ...........................................................................................................................4 1. GENERAL DESCRIPTION ......................................................................................................................................5 1.1 Applicant......................................................................................................................................................................... 5 1.2 Manufacturer .................................................................................................................................................................. 5 1.3 Product Feature of Equipment Under Test ..................................................................................................................... 5 1.4 Product Specification of Equipment Under Test ............................................................................................................. 5 1.5 Modification of EUT ........................................................................................................................................................ 6 1.6 Testing Location ............................................................................................................................................................. 6 1.7 Applicable Standards...................................................................................................................................................... 6 2. TEST CONFIGURATION OF EQUIPMENT UNDER TEST ....................................................................................7 2.1 Descriptions of Test Mode .............................................................................................................................................. 7 2.2 Connection Diagram of Test System .............................................................................................................................. 8 2.3 Table for Supporting Units .............................................................................................................................................. 9 2.4 EUT Operation Test Setup ............................................................................................................................................. 9 3. TEST RESULTS .....................................................................................................................................................10 3.1 AC Power Line Conducted Emissions Measurement ................................................................................................... 10 3.2 20dB and 99% OBW Spectrum Bandwidth Measurement............................................................................................ 12 3.3 Frequency Stability Measurement ................................................................................................................................ 13 3.4 Field Strength of Fundamental Emissions and Mask Measurement ............................................................................. 14 3.5 Radiated Emissions Measurement ............................................................................................................................... 16 3.6 Antenna Requirements ................................................................................................................................................. 19 4. LIST OF MEASURING EQUIPMENT ....................................................................................................................20 5. UNCERTAINTY OF EVALUATION .......................................................................................................................21 APPENDIX A. TEST RESULTS OF CONDUCTED EMISSION TEST APPENDIX B. TEST RESULTS OF CONDUCTED TEST ITEMS B1. Test Result of 20dB Spectrum Bandwidth B2. Test Result of Frequency Stability APPENDIX C. TEST RESULTS OF RADIATED TEST ITEMS C1. Test Result of Field Strength of Fundamental Emissions C2. Results of Radiated Emissions (9 kHz~30MHz) C3. Results of Radiated Emissions (30MHz~1GHz) APPEDNIX D. SETUP PHOTOGRAPHS Sporton International (Shenzhen) Inc. Page Number : 2 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C REVISION HISTORY REPORT NO. VERSION DESCRIPTION ISSUED DATE FR980203C Rev. 01 Initial issue of report Sep. 05, 2019 Sporton International (Shenzhen) Inc. Page Number : 3 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C SUMMARY OF THE TEST RESULT Report FCC Rule Description of Test Result Remark Section Under limit AC Power Line Conducted 3.1 15.207 Complies 13.83 dB at Emissions 0.150MHz 15.215(c) 20dB Spectrum Bandwidth Complies - 3.2 99% OBW Spectrum - Complies - Bandwidth 3.3 15.225(e) Frequency Stability Complies - Max level Field Strength of 3.4 15.225(a)(b)(c) Complies 56.45 dBμV/m at Fundamental Emissions 13.560 MHz Under limit Radiated Spurious 3.5 15.225(d) & 15.209 Complies 4.50 dB at Emissions 83.350MHz 3.6 15.203 Antenna Requirements Complies - Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and Explanations: The declared of product specification for EUT presented in the report are provided by the manufacturer, and the manufacturer takes all the responsibilities for the accuracy of product specification. Sporton International (Shenzhen) Inc. Page Number : 4 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 1. General Description 1.1 Applicant PAX Technology Limited Room 2416, 24/F., Sun Hung Kai Centre, 30 Harbour Road, Wanchai, Hong Kong 1.2 Manufacturer PAX Computer Technology (Shenzhen) Co., Ltd. 4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech industrial Park, Shenzhen, Guangdong, P.R.C. 1.3 Product Feature of Equipment Under Test Product Feature Equipment Secure Card Reader Brand Name PAX Model Name D135 FCC ID V5PD135 EUT supports Radios application Bluetooth BR/EDR/LE; NFC HW Version D135-xxx-xxx-xxxx SW Version V0.0.0.1 EUT Stage Production Unit Remark: The above EUT's information was declared by manufacturer. Please refer to the specifications or user's manual for more detailed description. 1.4 Product Specification of Equipment Under Test Standards-related Product Specification Tx/Rx Frequency Range 13.553 ~ 13.567MHz Channel Number 1 20dBW 2.576 KHz 99%OBW 2.185 KHz Antenna Type PCB Antenna Type of Modulation ASK Remark: The above EUT's information was declared by manufacturer. Please refer to the specifications or user's manual for more detailed description. Sporton International (Shenzhen) Inc. Page Number : 5 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

somov «. _FCC RF Test Report Report No. : FR980203C 1.5 Modification of EUT No modifications are made to the EUT during all test items. 1.6 Testing Location Sporton International (Shenzhen) Inc. is accredited to ISO/IEC 17025:2017 by American Association for Laboratory Accreditation with Certificate Number 5145.01. Test Site Sporton International (Shenzhen) Inc. 1/F, 2/F, Bldg 5, Shiling Industrial Zone, Xinwei Village, Xili, Nanshan, Shenzhen, Test Site 518055 People‘s Republic of China Location TEL: +86—755—86379589 FAX: +86—755—86379595 Sporton Site No. FCC Designation FCC Test Firm Test Site No. No. Registration No. THO1—SZ COQ1—S2Z Test Engineer Andy Xu Dalin Liu Temperature 24~26°C 22~25°C CN1256 421272 Relative Humidity 50~53% 50~55% Test Site Sporton International (Shenzhen) Inc. Test Site No. 3 Bldg the third floor of south, Shahe River west, Fengzeyuan Warehouse, . Nanshan Shenzhen, 518055 People‘s Republic of China Location TEL: +86—755—33202398 Sporton Site No. FCC Designation FCC Test Firm Test Site No. No. Registration No. 03CHO4—SZ Test Engineer Eeiyan Zhang Temperature 24~25°C CN1256 421272 Relative Humidity 48~49% 1.7 Applicable Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: + 47 CFR Part 15 Subpart C §15.225 + ANSI C63.10—2013 Sporton International (Shenzhen) Inc. Page Number : 6 of 21 TEL : 86—755—8637—9589 Report Issued Date : Sep. 05, 2019 FAX : 86—755—8637—9595 Report Version : Rev. 01 FCC ID: VSPD135 Report Template No.: BUS—FR1SCNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 2. Test Configuration of Equipment Under Test 2.1 Descriptions of Test Mode Investigation has been done on all the possible configurations. The following table is a list of the test modes shown in this test report. Test Items AC Power Line Conducted Emissions Field Strength of Fundamental Emissions 20dB Spectrum Bandwidth Frequency Stability Radiated Emissions 9kHz~30MHz Radiated Emissions 30MHz~1GHz The EUT pre-scanned in two NFC type, A, B. The worst type (type A) was recorded in this report. Pre-scanned tests, X, Y, Z in three orthogonal panels to determine the final configuration (Y plane as worst plane) from all possible combinations. Test Cases AC Mode 1 : Bluetooth Link + Charging From POS(D210) + NFC Tx + Conducted POS(D210)Charging from Adapter Emission Remark: For Radiated Test Cases, The tests were performance with POS Sporton International (Shenzhen) Inc. Page Number : 7 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 2.2 Connection Diagram of Test System For Conduction BT Earphone Power POS EUT Source This example is connection diagram of EUT test configurations. . For detail, please refer to test mode configuration and setup photographs for each test item. For Radiated NFC POS EUT This example is connection diagram of EUT test configurations. . For detail, please refer to test mode configuration and setup photographs for each test item. Sporton International (Shenzhen) Inc. Page Number : 8 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 2.3 Table for Supporting Units Item Equipment Trade Name Model Name FCC ID Data Cable Power Cord Bluetooth 1. Samsung EO-MG900 PYAHS-107W N/A N/A Earphone 2. NFC Card N/A N/A N/A N/A N/A 3. POS PAX D210 N/A N/A N/A 2.4 EUT Operation Test Setup The EUT was programmed to be in continuously transmitting mode. The ancillary equipment, NFC card, is used to make the EUT (NFC) continuously transmit at 13.56MHz and is placed around 3 cm gap to the EUT. Sporton International (Shenzhen) Inc. Page Number : 9 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3. Test Results 3.1 AC Power Line Conducted Emissions Measurement 3.1.1 Limit of AC Conducted Emission For equipment that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table. Frequency of Emission Conducted Limit (dBμV) (MHz) Quasi-Peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 *Decreases with the logarithm of the frequency. 3.1.2 Measuring Instruments See list of measuring instruments of this test report. 3.1.3 Test Procedures 1. The EUT was placed 0.4 meter from the conducting wall of the shielding room, and it was kept at least 80 centimeters from any other grounded conducting surface. 2. Connect EUT to the power mains through a line impedance stabilization network (LISN). 3. All the support units are connecting to the other LISN. 4. The LISN provides 50 ohm coupling impedance for the measuring instrument. 5. The FCC states that a 50 ohm, 50 microhenry LISN should be used. 6. Both sides of AC line were checked for maximum conducted interference. 7. The frequency range from 150 kHz to 30 MHz was searched. 8. Set the test-receiver system to Peak Detect Function and specified bandwidth (IF Bandwidth = 9kHz) with Maximum Hold Mode. Then measurement is also conducted by Average Detector and Quasi-Peak Detector Function respectively. Sporton International (Shenzhen) Inc. Page Number : 10 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.1.4 Test setup 3.1.5 Test Result of AC Conducted Emission Please refer to Appendix A. Sporton International (Shenzhen) Inc. Page Number : 11 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.2 20dB and 99% OBW Spectrum Bandwidth Measurement 3.2.1 Limit Intentional radiators must be designed to ensure that the 20dB and 99% emission bandwidth in the specific band 13.553~13.567MHz. 3.2.2 Measuring Instruments See list of measuring instruments of this test report. 3.2.3 Test Procedures 1. The spectrum analyzer connected via a receive antenna placed near the EUT in peak Max hold mode. 2. The resolution bandwidth of 1 kHz and the video bandwidth of 3 kHz were used. 3. Measured the spectrum width with power higher than 20dB below carrier. 4. Measured the 99% OBW. 3.2.4 Test Setup 3.2.5 Test Result of Conducted Test Items Please refer to Appendix B. Sporton International (Shenzhen) Inc. Page Number : 12 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.3 Frequency Stability Measurement 3.3.1 Limit The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% (100ppm) of the operating frequency over a temperature variation of -20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 3.3.2 Measuring Instruments See list of measuring instruments of this test report. 3.3.3 Test Procedures 1. The spectrum analyzer connected via a receive antenna placed near the EUT. 2. EUT have transmitted signal and fixed channelize. 3. Set the spectrum analyzer span to view the entire emissions bandwidth. 4. Set RBW = 1 kHz, VBW = 3 kHz with peak detector and maxhold settings. 6 5. The fc is declaring of channel frequency. Then the frequency error formula is (fc-f)/fc × 10 ppm and the limit is less than ±100ppm. 6. Extreme temperature rule is -20°C~50°C. 3.3.4 Test Setup 3.3.5 Test Result of Conducted Test Items Please refer to Appendix B. Sporton International (Shenzhen) Inc. Page Number : 13 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.4 Field Strength of Fundamental Emissions and Mask Measurement 3.4.1 Limit Rules and specifications FCC CFR 47 Part 15 section 15.225 Description Compliance with the spectrum mask is tested with RBW set to 9kHz. Field Strength Field Strength Field Strength Field Strength Freq. of Emission (MHz) (μV/m) at 30m (dBμV/m) at 30m (dBμV/m) at 10m (dBμV/m) at 3m 1.705~13.110 30 29.5 48.58 69.5 13.110~13.410 106 40.5 59.58 80.5 13.410~13.553 334 50.5 69.58 90.5 13.553~13.567 15848 84.0 103.08 124.0 13.567~13.710 334 50.5 69.58 90.5 13.710~14.010 106 40.5 59.58 80.5 14.010~30.000 30 29.5 48.58 69.5 3.4.2 Measuring Instruments See list of measuring instruments of this test report. Sporton International (Shenzhen) Inc. Page Number : 14 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.4.3 Test Procedures 1. Configure the EUT according to ANSI C63.10. The EUT was placed on the top of the turntable 0.8 meter above ground. The phase center of the loop receiving antenna mounted antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the receiving antenna was fixed at one meter above ground to find the maximum emissions field strength. 4. For Fundamental emissions, use the receiver to measure QP reading. 5. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum value. 6. Compliance with the spectrum mask is tested with RBW set to 9kHz. Note: Emission level (dBμV/m) = 20 log Emission level (μV/m). 3.4.4 Test Setup For radiated emissions below 30MHz 3.4.5 Test Result of Field Strength of Fundamental Emissions and Mask Please refer to Appendix C. Sporton International (Shenzhen) Inc. Page Number : 15 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.5 Radiated Emissions Measurement 3.5.1 Limit The field strength of any emissions which appear outside of 13.110 ~14.010MHz band shall not exceed the general radiated emissions limits. Frequencies Field Strength Measurement Distance (MHz) (μV/m) (meters) 0.009~0.490 2400/F(kHz) 300 0.490~1.705 24000/F(kHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 3.5.2 Measuring Instruments See list of measuring instruments of this test report. 3.5.3 Measuring Instrument Setting The following table is the setting of receiver. Receiver Parameter Setting Attenuation Auto Frequency Range: 9kHz~150kHz RBW 200Hz for QP Frequency Range: 150kHz~30MHz RBW 9kHz for QP Frequency Range: 30MHz~1000MHz RBW 120kHz for Peak Note: The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90 kHz, 110-490 kHz. Radiated emission limits in these two bands are based on measurements employing an average detector. Sporton International (Shenzhen) Inc. Page Number : 16 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.5.4 Test Procedures 1. Configure the EUT according to ANSI C63.10. The EUT was placed on the top of the turntable 0.8 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum value. 7. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. Antenna Requirements Sporton International (Shenzhen) Inc. Page Number : 17 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.5.5 Test Setup For radiated emissions below 30MHz For radiated emissions above 30MHz 3.5.6 Test Result of Radiated Emissions Measurement Please refer to Appendix C. Remark: There is a comparison data of both open-field test site and semi-Anechoic chamber, and the result came out very similar. Sporton International (Shenzhen) Inc. Page Number : 18 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 3.6 Antenna Requirements 3.6.1 Standard Applicable Except for special regulations, the Low-power Radio-frequency Devices must not be equipped with any jacket for installing an antenna with extension cable. An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the rule. 3.6.2 Antenna Anti-Replacement Construction An embedded-in antenna design is used. Sporton International (Shenzhen) Inc. Page Number : 19 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 4. List of Measuring Equipment Calibration Instrument Manufacturer Model No. Serial No. Characteristics Test Date Due Date Remark Date Spectrum Conducted R&S FSP30 101400 9KHz~30GHz Dec. 22, 2018 Aug. 15, 2019 Dec. 21, 2019 Analyzer (TH01-SZ) Pulse Power Conducted Anritsu MA2411B 1207253 30MHz~40GHz Dec. 22, 2018 Aug. 15, 2019 Dec. 21, 2019 Senor (TH01-SZ) 50MHz Conducted Power Meter Anritsu ML2495A 1218010 Dec. 22, 2018 Aug. 15, 2019 Dec. 21, 2019 Bandwidth (TH01-SZ) Aug. 22, 2019~ Radiation EMI Test Receiver R&S ESR7 101404 9kHz~7GHz Apr. 18, 2019 Apr. 17, 2020 Aug. 27, 2019 (03CH04-SZ) EXA Spectrum MY551502 Aug. 22, 2019~ Radiation KEYSIGHT N9010A 10Hz~44GHz Apr. 18, 2019 Apr. 17, 2020 Analyzer 13 Aug. 27, 2019 (03CH04-SZ) Aug. 22, 2019~ Radiation Loop Antenna R&S HFH2-Z2 100354 9kHz~30MHz May 29, 2018 May 28, 2020 Aug. 27, 2019 (03CH04-SZ) Aug. 22, 2019~ Radiation Bilog Antenna TeseQ CBL6111D 41909 30MHz~1GHz Aug. 19, 2019 Aug. 20, 2020 Aug. 27, 2019 (03CH04-SZ) Double Ridge SCHWARZBE 9120D-147 Aug. 22, 2019~ Radiation BBHA9120D 1GHz~18GHz Apr. 01, 2019 Mar. 31, 2020 Horn Antenna CK 4 Aug. 27, 2019 (03CH04-SZ) SCHWARZBE Aug. 22, 2019~ Radiation Horn Antenna BBHA9170 9170#679 15GHz~40GHz Apr.19，2019 Apr. 18, 2020 CK Aug. 27, 2019 (03CH04-SZ) 0.01Hz Aug. 22, 2019~ Radiation Amplifier Burgeon BPA-530 102211 Oct. 18, 2018 Oct. 17, 2019 ~3000MHz Aug. 27, 2019 (03CH04-SZ) AMF-7D-0010 Aug. 22, 2019~ Radiation HF Amplifier MITEQ 1800-30-10P- 1943528 1GHz~18GHz Oct. 18,2018 Oct. 17, 2019 Aug. 27, 2019 (03CH04-SZ) R TTA1840-35- Aug. 22, 2019~ Radiation HF Amplifier MITEQ 1871923 18GHz~40GHz Jul. 22, 2019 Jul. 21, 2020 HG Aug. 27, 2019 (03CH04-SZ) Agilent MY532701 500MHz~26.5G Aug. 22, 2019~ Radiation Amplifier 83017A Aug. 19, 2019 Aug. 20, 2020 Technologies 56 Hz Aug. 27, 2019 (03CH04-SZ) Aug. 22, 2019~ Radiation AC Power Source Chroma 61601 N/A N/A NCR NCR Aug. 27, 2019 (03CH04-SZ) Aug. 22, 2019~ Radiation Turn Table EM EM1000 N/A 0~360 degree NCR NCR Aug. 27, 2019 (03CH04-SZ) Aug. 22, 2019~ Radiation Antenna Mast EM EM1000 N/A 1 m~4 m NCR NCR Aug. 27, 2019 (03CH04-SZ) Conduction EMI Receiver R&S ESR7 101630 9kHz~7GHz; Dec. 23, 2018 Aug. 09, 2019 Dec. 22, 2019 (CO01-SZ) Conduction AC LISN EMCO 3816/2SH 00103912 9kHz~30MHz Oct. 18, 2018 Aug. 09, 2019 Oct. 17, 2019 (CO01-SZ) AC LISN Conduction (for auxiliary EMCO 3816/2SH 00103892 9kHz~30MHz Dec. 23, 2018 Aug. 09, 2019 Dec. 22, 2019 (CO01-SZ) equipment) 616020000 Conduction AC Power Source Chroma 61602 100Vac~250Vac Jul. 23, 2019 Aug. 09, 2019 Jul. 22, 2020 891 (CO01-SZ) NCR: No Calibration Required Sporton International (Shenzhen) Inc. Page Number : 20 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C 5. Uncertainty of Evaluation The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI 63.10-2013. All the measurement uncertainty value were shown with a coverage K=2 to indicate 95% level of confidence. The measurement data show herein meets or exceeds the CISPR measurement uncertainty values specified in CISPR 16-4-2 and can be compared directly to specified limit to determine compliance. Uncertainty of Conducted Emission Measurement (150 kHz ~ 30 MHz) Measuring Uncertainty for a Level of Confidence 2.6dB of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (9 kHz ~ 30 MHz) Measuring Uncertainty for a Level of Confidence 5.0dB of 95% (U = 2Uc(y)) Uncertainty of Radiated Emission Measurement (30 MHz ~ 1000 MHz) Measuring Uncertainty for a Level of Confidence 5.0dB of 95% (U = 2Uc(y)) Sporton International (Shenzhen) Inc. Page Number : 21 of 21 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135 Report Template No.: BU5-FR15CNFC Version 2.0

FCC RF Test Report Report No. : FR980203C Appendix A. Test Results of Conducted Emission Test Temperature : 22~25℃ Test Engineer : Dalin Liu Relative Humidity : 50~55% Test Voltage : 120Vac / 60Hz Phase : Line Remark : All emissions not reported here are more than 10 dB below the prescribed limit. (1) with antenna Remark: 13.560MHz is the NFC RF fundamental signal. Sporton International (Shenzhen) Inc. Page Number : A1 of A4 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C Temperature : 22~25℃ Test Engineer : Dalin Liu Relative Humidity : 50~55% Test Voltage : 120Vac / 60Hz Phase : Neutral Remark : All emissions not reported here are more than 10 dB below the prescribed limit. (1) with antenna Remark: 13.560MHz is the NFC RF fundamental signal. Sporton International (Shenzhen) Inc. Page Number : A2 of A4 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C Temperature : 22~25℃ Test Engineer : Dalin Liu Relative Humidity : 50~55% Test Voltage : 120Vac / 60Hz Phase : Line Remark : All emissions not reported here are more than 10 dB below the prescribed limit. (2) With dummy load Remark: Only the fundamental NFC signal needs to be retested per KDB 174176. Sporton International (Shenzhen) Inc. Page Number : A3 of A4 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C Temperature : 22~25℃ Test Engineer : Dalin Liu Relative Humidity : 50~55% Test Voltage : 120Vac / 60Hz Phase : Neutral Remark : All emissions not reported here are more than 10 dB below the prescribed limit. (2) With dummy load Remark: Only the fundamental NFC signal needs to be retested per KDB 174176. Sporton International (Shenzhen) Inc. Page Number : A4 of A4 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C Appendix B. Test Results of Conducted Test Items B1. Test Result of 20dB Spectrum Bandwidth Test mode NFC Tx Test Frequency (MHz) 13.56 20dB Bandwidth (kHz) 2.576 99% OccupiedBW(kHz) 2.185 fL＞13.553 13.55848 Test Result Frequency range (MHz) fH＜13.567 13.561056 Complies Remark: Because the measured signal is CW adjusting the RBW per C63.10 would not be practical since measured bandwidth will always follow the RBW and the result will be approximately twice the RBW. Sporton International (Shenzhen) Inc. Page Number : B1 of B2 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C B2. Test Result of Frequency Stability B3. Voltage vs. Frequency Stability Temperature vs. Frequency Stability Measurement Measurement Voltage (Vac) Temperature (℃) Frequency (MHz) Frequency (MHz) 3.60 13.559768 -20 13.559754 3.85 13.559768 -10 13.559754 4.40 13.559768 0 13.559754 10 13.559768 20 13.559768 30 13.559768 40 13.559768 50 13.559768 Max.Deviation (MHz) -0.000232 Max.Deviation (MHz) -0.000246 Max.Deviation (ppm) -17.1091 Max.Deviation (ppm) -18.1416 Limit FS < ±100 ppm Limit FS < ±100 ppm Test Result PASS Test Result PASS Sporton International (Shenzhen) Inc. Page Number : B2 of B2 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C Appendix C. Test Results of Radiated Test Items C1. Test Result of Field Strength of Fundamental Emissions Test Mode : NFC Tx Test Frequency (MHz) 13.56 Sporton International (Shenzhen) Inc. Page Number : C1 of C3 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C C2. Results of Radiated Spurious Emissions (9 kHz~30MHz) Test Mode : NFC Tx Polarization : Horizontal Frequency Level Over Limit Read Antenna Cable Ant Table Remark Limit Line Level Factor Loss Pos Pos ( MHz ) ( dBμV/m ) ( dB ) ( dBμV/m ) (dBμV) ( dB ) ( dB ) ( cm ) ( deg ) 0.00946 56.08 -72.01 128.09 35.02 21 0.06 - - Average 0.07683 52.53 -57.36 109.89 31.96 20.5 0.07 - - Average 0.11532 50.35 -56.02 106.37 29.67 20.6 0.08 - - Average 0.13329 40.59 -64.52 105.11 19.91 20.6 0.08 - - Average 0.15185 51.66 -52.32 103.98 31.28 20.3 0.08 - - Average 2.09 37.27 -32.73 70 16.61 20.55 0.11 - - QP 9.904 36.59 -33.41 70 15.84 20.35 0.4 - - QP 19.051 34.49 -35.51 70 14.47 19.49 0.53 - - QP 29.92 35.48 -34.52 70 15.08 19.66 0.74 - - QP Test Mode : NFC Tx Polarization : Vertical Frequency Level Over Limit Read Antenna Cable Ant Table Remark Limit Line Level Factor Loss Pos Pos ( MHz ) ( dBμV/m ) ( dB ) ( dBμV/m ) (dBμV) ( dB ) ( dB ) ( cm ) ( deg ) 0.009 51.44 -77.08 128.52 30.38 21 0.06 - - Average 0.07677 51.58 -58.32 109.9 31.01 20.5 0.07 - - Average 0.11526 50.24 -56.13 106.37 29.56 20.6 0.08 - - Average 0.12828 38.26 -67.18 105.44 17.58 20.6 0.08 - - Average 0.15555 50.89 -52.88 103.77 30.51 20.3 0.08 - - Average 4.772 36.67 -33.33 70 16.25 20.32 0.1 - - QP 14.688 35.23 -34.77 70 15.34 19.42 0.47 - - QP 21.301 35.48 -34.52 70 15.61 19.29 0.58 - - QP 29.93 35.81 -34.19 70 15.39 19.68 0.74 - - QP Note: 1. The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. 2. Distance extrapolation factor = 40 log (specific distance / test distance) (dB); 3. Limit line = specific limits (dBμV) + distance extrapolation factor. Sporton International (Shenzhen) Inc. Page Number : C2 of C3 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135

FCC RF Test Report Report No. : FR980203C C3. Results of Radiated Spurious Emissions (30MHz~1GHz) Test Mode : NFC Tx Polarization : Horizontal Frequency Level Over Limit Read Antenna Cable Preamp Ant Table Remark Limit Line Level Factor Loss Factor Pos Pos ( MHz ) ( dBμV/m ) ( dB ) ( dBμV/m ) (dBμV) ( dB ) ( dB ) ( dB ) ( cm ) ( deg ) 83.35 35.5 -4.5 40 52.67 13.82 0.96 31.95 100 176 Peak 167.74 34.86 -8.64 43.5 49.48 15.87 1.35 31.84 - - Peak 215.27 37.92 -5.58 43.5 52.99 15.25 1.52 31.84 - - Peak 275.41 41.04 -4.96 46 51.9 19.33 1.72 31.91 - - Peak 312.27 37.36 -8.64 46 47.91 19.7 1.83 32.08 - - Peak 384.05 30.5 -15.5 46 39.03 21.43 2.04 32 - - Peak Test Mode : NFC Tx Polarization : Vertical Frequency Level Over Limit Read Antenna Cable Preamp Ant Table Remark Limit Line Level Factor Loss Factor Pos Pos ( MHz ) ( dBμV/m ) ( dB ) ( dBμV/m ) (dBμV) ( dB ) ( dB ) ( dB ) ( cm ) ( deg ) 30 23.24 -16.76 40 29.96 24.8 0.58 32.1 - - Peak 83.35 24.71 -15.29 40 41.88 13.82 0.96 31.95 - - Peak 167.74 24.31 -19.19 43.5 38.93 15.87 1.35 31.84 - - Peak 288.02 32.21 -13.79 46 43.31 19.16 1.75 32.01 100 111 Peak 299.66 28.17 -17.83 46 39.08 19.4 1.79 32.1 - - Peak 784.66 30.76 -15.24 46 30.75 28.22 2.93 31.14 - - Peak Note: 1. The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. 2. Emission level (dBμV/m) = 20 log Emission level (μV/m). 3. Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor= Level. Sporton International (Shenzhen) Inc. Page Number : C3 of C3 TEL : 86-755-8637-9589 Report Issued Date : Sep. 05, 2019 FAX : 86-755-8637-9595 Report Version : Rev. 01 FCC ID: V5PD135


Document Created: 2019-09-16 20:14:33
Document Modified: 2019-09-16 20:14:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC