SAR Test Report Part 4of4

FCC ID: V3H-B8

RF Exposure Info

Download: PDF
FCCID_913595

NCL Calibration Laboratories Division of APREL Laboratories. Sensitivity in Body Tissue Frequency: 1900 MHz Epsilon: 53.3 (+/—5%) Sigma: 1.52 S/im (+/—5%) ConvF Channel X: 5.75 Channel Y: 5.75 Channel Z: 5.75 Tissue sensitivity values were calculated using the load impedance of the APREL Laboratories Dag—Paq. Boundary Effect: Uncertainty resulting from the boundary effect is less than 2% for the distance between the tip of the probe and the tissue boundary, when less than 2.44mm. Spatial Resolution: The measured probe tip diameter is 5 mm (+/— 0.01 mm) and therefore meets the requirements of SSI/DRB—TP—D01—032 for spatial resolution. Page 4 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

NCL Calibration Laboratories Division of APREL Laboratories. Receiving Pattern 1900 MHz (Air) Receiving Pattern Probe s/n 264 1900MHz ==#— Civt —Bi—Ch2 —i—ChE —6—Tot Page 5 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Isotropy Error 1900 MHz (Air) ’7 Isotropy Error Probe s/n 264 1900MHz 34664644 bittocne auovo 08 Error [dB] 0 100 200 300 Isotropy Plot Probe s/n 264 1900MHz os zis Voltage (mV) Degrees (x10) om Isotropicity in Tissue: 0.10 dB Page 6 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

NCL Calibration Laboratories Division of APREL Laboratories. Dynamic Range Probe 264 Dynamic Range 10000 1000 +—— — 100 / —_——] Voltage [microv] —4&— Uncompensated 8 —t— Compensated 0.1 « 0.01 1.00 10.00 100.00 1,000.00 10,000.00 100,000.00 1,000,000.00 10,000,000.00 Electric Field [(Vim)®2) Page 7 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Video Bandwidth Probe Frequency Characteristics 73 . T11 TT nsc :‘ =SA6p 1 °|~*~ = 7 | $.] . | | $& 21— — ~ \ 4 | 5 f s \ s L } I | 1 I 1 | J 1 10 100 1000 10000 Frequency (Hz) Video Bandwidth at 500 Hz 1 dB Video Bandwidth at 1000 Hz 3 dB Page 8 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

NCL Calibration Laboratories Division of APREL Laboratories. Conversion Factor Uncertainty Assessment Frequency: 1900MHz Epsilon: 53.3 (+/—5%) Sigma: 1.52 S/im (+/—5%) ConvF Channel X: 5.75 7%(K=2) Channel Y: 5.75 7%(K=2) Channel Z: 5.75 7%(K=2) To minimize the uncertainty calculation all tissue sensitivity values were calculated using a load impedance of 5 MS2. Boundary Effect: For a distance of 2.4mm the evaluated uncertainty (increase in the probe sensitivity) is less than 2%. Page 9 of 10 This page has been reviewed for content and attested to on Page 2 ofthis document.

NCL Calibration Laboratories Division of APREL Laboratories. Test Equipment The test equipment used during Probe Calibration, manufacturer, model number and, current calibration status are listed and located on the main APREL server R:ANCL\Calibration Equipment\Instrument List May 2007. Page 10 of 10 This page has been reviewed for content and attested to on Page 2 of this document.

Appendix E. Dipole Calibration Data Validation Dipole 835MHz P/N: ALS-D-835-S-2 S/N: QTK-315










Appendix E. Dipole Calibration Data Validation Dipole 1900MHz P/N: ALS-D-1900-S-2 S/N: QTK-318

NCL CALIBRATION LABORATORIES Calibration File No: DC—408—1 Project Number: QTKB—Dipole Cal—5230 CERTIFICATE OF CALIBRATION it is certified that the equipment idenlified below has been calibrated in the NCL CALIBRATION LABORATORIES by qualified personnel following recognized procedures and using transfer standards traceable to NRC/NIST. Quietek Validation Dipole Manufacturer: APREL Laboratories Part number: ALS—D—1900—§—2 Frequency: 1.9 GHz Serial No: OTK—318 Customer: Quictek Calibrated: 15 June 2006 Released on: 15 June 2006 Catal aeee, w »*"*" yit" hx us .A 4 Released By: C/,!c. 51 SPECTRUM WAY Bivision ol APREL Lab NEPEAN, ONTARIO TEL: (613) 620—400a CANADA K2R 1E6 FAX: (613) 820—4161

NCL Calibration Laboratories Division of APREL Laboratories. Calibration Results Summary The following results relate the Calibrated Dipole and should be used as a quick reference for the user. Mechanical Dimensions Length: 70.0 mm Height: 39.5 mm Electrical Specification SWR: 11 U Return Loss: —25.7 4B Impedance: 46.8 Q System Validation Results | Frequency 1 Gram 10 Gram Peak 18 GHz 360 | 20.78 | 67.7 Page 1 of9 Calibrated by je: Approved by: +2( Sn n ie ies‘ Mieemnmm s en

NCL Calibration Laboratories Division of APREL Laboratories. Introduction This Calibration Report has been produced in line with the SSI Dipole Calibration Procedure SSI—TP—018—ALSAS. The results contained within this report are for Validation Dipole QTK—318. The calibration routine consisted of a three—step process. Step 1 was a mechanical verification of the dipole to ensure that it meets | the |IEEE/APREL mechanical specifications. Step 2 was an Electrical Calibration for — the Validation Dipole, where the SWR, Impedance, and the Return loss were assessed. Step 3 involved a System Validation using the ALSAS—10U, along with QTK E—020 130 MHz to 26 GHz E—Field Probe Serial Number 212. References SSI—TP—018—ALSAS Dipole Calibration Procedure SSI—TP—016 Tissue Calibration Procedure IEEE 1528 "Recommended Practice for Determining the Peak Spatial—Average _ Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques" Conditions Dipole QTK—318 was received for calibration. Ambient Temperature of the Laboratory: 22 °C +/— 0.5°C Temperature of the Tissue: 20 °C +/— 0.5°C us Page 3 of 9 Calibrated by /;// ‘z‘__a Approved by: _

NCL Calibration Laboratories Division of APREL Laboratories. Dipole Calibration Results Mechanical Verification IEEE Length IEEE Height Measured Measured Length Height 68.0 mm 39.5 mm 70.0 mm 39.5 mm Tissue Validation Head Tissue 1900 MHz Measured Dielectric constant, s; 39.9 Conductivity, & [S/m] 1.42 &~ yer ( C Page 4 of 9 Calibrated by _ Z» -’fi Approved by: _ C’: 6

NCL Calibration Laboratories Division of APREL Laboratories. Electrical Calibration Test |_ _ Result __ $11 NL —25.7 dB SWR 11 U ] |_ Impedance 46.8 0 _ The Following Graphs are the results as displayed on the Vector Network Analyzer. $11 Parameter Return Loss §22 REVERSE REFLECTION th 45— g22 REFERENCE PLANE LOG MAGNITUDE »REF=~—280.000 dB 5.000 d8/01V 0.0000 an PMARKER 1 1.898384 oHz "25.748 dP NARKER T0 MAX MARKER TO MIN : > : MARKER READOUT 1. 250614 GHz 2.050376 FUNCTIONS hi. x i x fauk. c Page 5 of 9 Calibrated by L Approved hy: _,..gfe =>

NCL Calibration Laboratories Division of APRET T ahoratories. SWR 399 REVERSE AEFLECTION cH 4 — s99 . SHR »REF—1.200 1 P00 .000 mU/DIV REFERENCE PLanE & 9.8000 in ' i | »MARKER 1 1.898384 oHz 1.186 i1 MARKER TN MAX MARKER TO MLN : 3 . . & : & : MARKER READOUT 1.750614 BHz 2.050376 FUNCTIONS es Sas j Co 4 Page 6 of 9 Calibrated by ,:-E, Approvedby: _6‘ _ A V

—_._ — ~——_—._>ma_— NCL Calibration Laboratories Division of APREL Laboratories. Smith Chart Dipole Impedance $22 REVERSE REFLECTION 1 nfusts s CH 4 — §22 INPEDANCE m * REFERENCE PLANE 0.9000 mn RMARKER 1 — 1.898384 GHz 146.767 9 > ~3.770 j2 MARKER TO MAX MARKER TO HIN MARKER READOUT 1.250614 — 2.050376 GHz FUNCTIONS Page 7 of0 h — Calibrated by _/ _C_ 5 Approved by: C «>>

NCL Calibration Laboratories Division of APREL Laboratories. System Validation Results Using the Electrically Calibrated Dipole ] FrequencyI 1 Gram | 10 Gram | ~Posk — _Above Faed Point _. | 19 GHz | 36.0 | 20.78 | _ 67.7 Puge 8 of 9 Calibrated by .7 / C Approved by:

NCL Calibration l.sborfitnrics Division of APREL Laboratories. Test Equipment The test equipment used during Probe Calibration, manufacturer, model number and, current calibration status are listed and located on the main APREL server . R:ANCL\Calibration Equipment\instrument List | §1% mell ce 5y Page 9 of9 Calibrated by _/_ "* Approved by: <~ C


Document Created: 2008-03-10 17:49:21
Document Modified: 2008-03-10 17:49:21
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC