Test Report NFC main

FCC ID: V2TSDHTAG3NFC

Test Report

Download: PDF
FCCID_4508945

TEST REPORT No.: 17-1-0133807T02a According to: Title 47 FCC Regulations Subpart 15C §15.225 ISED-Regulations RSS-Gen, Issue 5 RSS-210, Issue 9 for WITTE - Velbert GmbH & Co. KG DAG SDH TAG3 NFC Outer Door Handle with NFC FCC ID: V2T-SDHTAG3NFC ISED ID: 7575A-SDHTAG3NFC Laboratory Accreditation and Listings Accredited EMC-Test Laboratory accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 30 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 17-1-0133807T02a, Page 2 of 30 Table of contents 1. SUMMARY OF TEST RESULTS................................................................................................................... 3 1.1. TEST OVERVIEW FCC 15.225 AND ISED RSS-210, ISSUE 9 ............................................................... 3 1.2. Attestation:.................................................................................................................................................... 4 2. ADMINISTRATIVE DATA ............................................................................................................................ 5 2.1. Identification of the testing laboratory .......................................................................................................... 5 2.2. Test location ................................................................................................................................................. 5 2.3. Organizational items ..................................................................................................................................... 5 2.4. Applicant’s details ........................................................................................................................................ 5 2.5. Manufacturer’s details .................................................................................................................................. 5 3. EQUIPMENT UNDER TEST (EUT) .............................................................................................................. 6 3.1. Technical data of main EUT declared by applicant ...................................................................................... 6 3.2. EUT: Type, S/N etc. and short descriptions used in this test report ............................................................. 6 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions ............................................................... 7 3.4. EUT set-ups .................................................................................................................................................. 7 3.5. EUT operating modes ................................................................................................................................... 8 3.6. Configuration of cables used for testing ....................................................................................................... 8 4. DESCRIPTION OF TEST SYSTEM SET-UP’S ........................................................................................... 9 4.1. Test system set-up for radiated magnetic field measurements below 30 MHz ............................................. 9 4.2. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz .......................................... 10 4.3. Test system set-up for conducted measurements on antenna port .............................................................. 11 5. MEASUREMENTS ........................................................................................................................................ 12 5.1. Radiated field strength emission and mask at 13.110-14.010MHz §15.225(1)(2)(3)(4) ........................ 12 5.2. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz ......................................................... 15 5.3. Frequency error (tolerance) §15.225( e) .................................................................................................. 18 5.4. RF-Parameter - 99% occupied Bandwith ................................................................................................... 21 5.5. Measurement uncertainties ......................................................................................................................... 23 6. ABBREVIATIONS USED IN THIS REPORT ............................................................................................ 24 7. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES .................... 24 8. INSTRUMENTS AND ANCILLARY ........................................................................................................... 25 8.1. Used equiment “CTC” ................................................................................................................................ 25 9. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ........................................................................ 30 Table of annex Total pages Annex 1: separate document measuring diagrams (CETECOM_TR17_1_0133807T02a_A1) 16 Annex 2: separate document external photographs (CETECOM_TR17_1_0133807T02a_A2) 9 Annex 3: TO BE PROVIDED BY APPLICANT Annex 4: separate document test set-up photos (CETECOM_TR17_1_0133807T02a_A4) 5 The listed attachments are an integral part of this report. CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 3 of 30 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. Also we refer on special conditions with the applicant should fulfill according §2.927 to §2.948, special focus regarding modification of the equipment and availability of sample equipment for market surveillance tests. The Equipment Under Test (in this report, hereinafter referred as EUT) incorporates an NFC-Transceiver working at 13.56 MHz nominal frequency. Other wireless technologies were not considered within this test report. Following tests have been performed to show compliance with applicable FCC Part 15, Subpart C (Unintentional Radiators) of the CFR 47 Rules, Edition 2018 and Canadian RSS-210: Issue 9, RSS-Gen., Issue 5 standards. 1.1. TEST OVERVIEW FCC 15.225 AND ISED RSS-210, ISSUE 9 TX-Mode TEST PORT REFERENCES & LIMITS EUT EUT Result CASES set-up opera- FCC RSS Section Test limit ting Standard mode 84dBµV/m 13.553-13.567 MHz 50.5dBµV/m 13.410-13.553 MHz Radiated field RSS-210, 13.567-13.710 MHz strength in 30m §2.1046 Issue 9, measurement Cabinet §15.225(a)(b) 1 2 passed Chapter 40.5 dBµV/m distance) & (c)(d) B.6(a)(b)(c)(d) 1.110-13.410 MHz emission mask 13.710-14.010 MHz 29.5dBµV/m outside the band 13.110-14.010 MHz 99% Antenna For §2.202(a) RSS Gen, Issue 5, Occupied coupling 99% Power 2 2 information §2.1049 Chapter 6.7 bandwidth (radiated) only General field Cabinet + RSS-Gen, strength inter- Issue 5 2400/F(kHz) µV/m emissions connecting §15.209(a) 24000/F(kHz) µV/m 1 2 passed (radiated - cables Chapter 8.9 30 µV/m (9 kHz (radiated) Table 6 to 30 MHz) General field Cabinet + RSS-Gen, Emissions in strength inter- Issue 5 restricted bands must emissions + connecting §15.209 meet the general 1 2 passed restricted bands cables Chapter 8.9 field-strength (30 MHz (radiated) Table 5+7 radiated limits to 1000 MHz) RSS-210, Frequency Antenna port §2.1055 Issue 9, ±100ppm 3 1 Pass stability (conducted) §15.225(e) Chapter B.6 Not RSS-Gen, Issue 5: FCC §15.207 limits -- -- Conducted AC-Power applicable §15.207 Chapter 8.8, Emissions lines Table 4 ISED: Table 4 - -- Remark 1 Reamrk: 1.) EUT placed inside car-environment CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 4 of 30 1.2. Attestation: I declare that all measurements were performed by me or under my supervision and that all measurements have been performed and are correct to my best knowledge and belief to Industry Canada standards. All requirements as shown in above table are met in accordance with enumerated standards. Digital signiert von: Christian Guangcheng Lorenz Datum: 2019.10. Huang 25 13:37:39 + 2019.10.25 13: 02'00' 32:08 +02'00' ...................................................... .................................................... Dipl.-Ing. Ch. Lorenz M.Sc. G. Huang Responsible for test section Responsible for test report CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 5 of 30 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Volker Wittmann Deputy: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report and Project leader: M.Sc. G. Huang Receipt of EUT: 2019-10-08 Date(s) of test: 2019-10-09 to 2019-10-14 Date of report: 2019-10-25 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 13.02 2.4. Applicant’s details Applicant’s name: WITTE - Velbert GmbH & Co. KG Address: Höferstraße 3-15 42551 Velbert Germany Contact person: Mr. Kay Lackmann 2.5. Manufacturer’s details Manufacturer’s name: same as applicant Address: same as applicant CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 6 of 30 3. Equipment under test (EUT) 3.1. Technical data of main EUT declared by applicant Frequency range and channels 13.553 - 13.567 MHz (US/Canada -bands) Type of modulation (packet types) 2-ASK (Amplitude Shift Keying) Number of channels 1 nominal channel at 13.56 MHz (USA/Canada -bands) Occupied bandwidth 1.835 MHz  Integrated Antenna Type  External, no RF- connector  External, separate RF-connector Antenna Gain No information from applicant MAX Field strength (radiated): 24.19 dBµV/m QP@30m distance Installed options  no other wireless (not tested within this test report) Power supply  DC power only: 13.5 Volt nominal (Lead-Acid battery) Special EMI components -- EUT sample type  Production  Pre-Production  Engineering Firmware  for normal use  Special version for test execution FCC/ISED label attached  yes  no 3.2. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware status software status tion*) **) **) **) EUT A DAG SDH TAG3 Outer Door Handle 191004_02 19.45.00 19.28.11 S283 NFC with NFC *) EUT short description is used to simplify the identification of the EUT in this test report. **) Information provided by applicant. CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 7 of 30 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE S/N HW SW short Auxiliary Equipment Type serial number hardware status software status descrip- **) **) **) tion *) AE 1 Shielding plate -- -- -- -- S44 AE 2 Testbox 190411_001/00 LIN Interface D3 D3 S28 Homologation 2 AE 3 Cable for DC supply banana connector -- -- -- S165 AE 4 Cable for DC supply banana connector -- -- -- S166 AE 5 Battery Yuasa NP4-12S 1807303L -- -- S25 AE 6 Homologation Smartphone Samsung Galaxy S9 -- -- S230 DAG SDH AE 7 Smartphone Holder Laser Sinter -- -- -- S287 AE 8 MB Test Card NFC Test card 003589072200 -- -- S90 *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. **) Information provided by applicant. 3.4. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) EUT A + AE 1 + AE 2 + AE 3 + AE 4 + For radiated measurements under nominal set. 1 AE 5 + AE 6 + AE 7 condition EUT A + AE 1 + AE 2 + AE 3 + AE 4 + set. 2 For bandwidth measurements AE 5 + AE 8 EUT A + AE 1 + AE 2 + AE 3 + AE 4 + For measurements under extreme conditions in a set. 3 AE 5 climatic chamber *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 8 of 30 3.5. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) op. 1 TX CW Continuous transmission mode (continuous wave signal) op. 2 TX modulated Continuous transmission mode (modulated signal) *) EUT operating mode no. is used to simplify the test report. 3.6. Configuration of cables used for testing Cable S/N HW Cable length Remark number Item Type serial number hardware status Cable 1 With banana For power Cable unit - - 100 cm S165 connector supply to AE 2 Cable 2 With banana For power Cable unit - - 100 cm S166 connector supply to AE 2 CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 9 of 30 4. Description of test system set-up’s 4.1. Test system set-up for radiated magnetic field measurements below 30 MHz Specification: ANSI C63.4-2014 §5.3, §8.2.1, §8.3.1.1+§8.3.2.1 , ANSI C63.10-2013 chapter 6.4 (§6.4.4.2) General Description: Evaluating the radiated field emissions are done first by an exploratory emission measurement and a final measurement for most critical frequencies determined. The loop antenna was placed at 1 m height above ground plane and 3 m measurement distance from set-up for investigations. Because of reduced measurement distance, correction data were applied, as stated in chapter “General Limit - Radiated field strength emissions below 30 MHz“. The tests are performed in the semi anechoic room recognized by the regulatory commission. Schematic: Testing method: Exploratory, preliminary measurement Final measurement on critical frequencies The EUT and it’s associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 0.8 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (step cable position, etc. 90°, range 0°to 360°) and the EUT itself either on 3-orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT), the emission spectrum was recorded. The precisely. After this step, for all identified critical loop antenna was moved at least to frequencies, the maximum peak was determined. 2-perpendicular axes (antenna vector in direction of EUT and parallel to EUT) in order to maximize Following parameters were varied: the turntable the emissions. The results are documented in a angle continuously in the range 0 to 360 degree, diagram. Critical frequencies (low margin to the EUT itself either over 3-orthogonal axis (not limit) are saved within a data reduction table for defined usage position) or 2-orthogonal axis further investigations. If various operating modes (defined usage position). are supported, further investigations are made to find the worst-case. Also the interconnection On the determined worst-case position, a final cables and equipment position were varied in measurement with necessary bandwidth and order to maximize the emissions. detector according standard has been carried out. Formula: EC = ER + AF + CL + DF - GA AF =Antenna factor CL = Cable loss M = LT-EC DF= Distance correction factor EC = Electrical field – corrected value ER = Receiver reading GA= Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. Distance correction: Reference for applied correction (extrapolating) factors due to reduced measurement distance: ANSI C63.10:2013, §6.4.4.2 - Equations (2) + (3) + (4) CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 10 of 30 4.2. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz Specification: ANSI C63.4-2014 chapter 8.2.3, ANSI C63.10-2013 chapter 6.5 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a NSA-compliant semi anechoic room (SAR) recognized by the regulatory commissions. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are placed Based on the exploratory measurements, the most on a non-conductive position manipulator (tipping critical frequencies are re-measured by main- device) of 0.8 m height which is placed on the taining the EUT’s worst-case operation mode, cable turntable. By rotating the turntable (range 0° to position, etc. either on 10m OATS or 3m semi- 360°, step 90°) and the EUT itself either on 3- anechoic room. orthogonal axis (portable equipment) or 2- orthogonal axis (defined operational position of First a frequency zoom around the critical frequency EUT) the emission spectrum and it’s is done to locate the frequency more precisely. After characteristics was recorded with an EMI- this step, for all identified critical frequencies, the receiver, broadband antenna and software. maximum peak was determined. Measurement antenna: horizontal and vertical, Following parameters were varied: the turntable heights: 1,0 m and 1,82 m as worst-case angle continuously in the range 0 to 360 degree, the determined by an exploratory emission EUT itself either over 3-orthogonal axis (not measurements. The results are documented in a defined usage position) or 2-orthogonal axis diagram. Critical frequencies (low margin to (defined usage position). The measurement antenna limit) are saved within a table for further height between 1 m and 4 m. investigations. If various operating modes are supported, further investigations are made to find On the determined worst-case position, a final the worst-case of them. Also the interconnection measurement with necessary bandwidth and cables and equipment position were varied in detector according standard has been carried out. order to maximize the emissions. Formula: EC = ER + AF + CL + DF - GA (1) AF = Antenna factor CL = Cable loss M = LT - EC (2) DF = Distance correction factor (if used) EC = Electrical field – corrected value ER = Receiver reading GA = Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 11 of 30 4.3. Test system set-up for conducted measurements on antenna port In case an external connector is not available, the coupling unit consists of a near-field antenna which is directly connected to the spectrum analyzer. The power level calibration of the spectrum analyzer is related to the power levels (field strengths) of the carrier determined in the anechoic-chamber. Schematic: Test set-up 2 conducted within climatic chamber CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 12 of 30 5. Measurements 5.1. Radiated field strength emission and mask at 13.110-14.010MHz §15.225(1)(2)(3)(4) 5.1.1. TEST LOCATION AND EQUIPMENT (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30   620 ESU26    spectr. analys.  120 FSEM  264 FSEK     antenna  048 EMCO3143  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  021 EMCO6502 power supply  Car battery  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix  477 GPS  5.1.2. STANDARDS AND LIMITS: CFR 47, §15.225(a)(b)(c)(d), RSS-210, Issue 9, Chapter B.6 Frequency Field strength Measurement Remarks [MHz] distance [μV/m] [dBuV/m] [meters] 13.553 -13.567 15.848 84.00 30 (allocated band) 13.410-13.710 334 50.47 30 Correction factor used due to measurement 13.110-14.010 106 40.50 30 distance of 3m Outside band 30 29.5 30 13.110-14.010 5.1.3. TEST CONDITION AND MEASUREMENT TEST SET-UP link to test system (if used):  air link  cable connection  EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver (Analyzer) Settings Span/Range: 9kHz to 150kHz; 150 kHz to 30 MHz RBW/VBW: 200Hz/auto; 10 kHz/ auto (ANSI63.10/CISPR#16) Detector/ Mode: PEAK, TRACE max-hold mode, repetitive scan for exploratory measurements Quasi-Peak, for final measurement on critical frequencies (f<1GHz) 5.1.4. GENERAL MEASUREMENT PROCEDURES: The measurement test set-up and test procedure are in accordance with the provisions described in ANSI 63.10: 2013 The Equipment under Test (EUT) was set-up to defined operating mode and installed (connected) to accessory equipment according the general description of use given by the applicant. The measurement loop antenna was situated in 3m distance to the EUT. Between EUT and measurement antenna absorbers are covering the GND-Plane. With these absorbers the chamber fulfills CIPR16-1-4 site VSWR-criteria. Radiated magnetic emission measurements were made with the antenna situated in 1 meter height. The loop antenna was moved at least to 2-perpendicular axes (antenna vector in direction of EUT and parallel to EUT) in order to maximize the emissions, the EUT itself either over 3-orthogonal axes (no defined usage position) or 2- orthogonal axis (defined usage position) by the position manipulator. According the standard the compliance should be checked in 30 m measurement distance. Therefore an additional extrapolation factor was used in order to normalize the measurement data. The frequency dependent extrapolation factor used for this reduced measurement distance, can be found in the chapter 5.1.7. Correction factors due to reduced meas. distance (f< 30 MHz). CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 13 of 30 5.1.5. MEASUREMENT RESULTS: CARRIER FIELD STRENGTH (EMISSION MASK) Table of measurement results: Diagram Carrier Set- OP- Used detector No. / Channel Frequency up mode Remark Result Sub- range no. no. Chapter Range No. PK AV QP EUT standing position 2.01 nominal 1 12 - 15 MHz 1 2 24.19 dBµV/m (Worst case    passed regarding field strength) EUT lying position 2.02 nominal 1 12 - 15 MHz 1 2 23.76 dBµV/m    passed Remark: *.) see diagrams enclosed in Annex 1 for details 5.1.6. MEASUREMENT RESULTS: RADIATED FIELD STRENGTH (SPURIOUS) Table of measurement results: Diagram Carrier Set- OP- Used detector No. / Channel Frequency up mode Remark Result Sub- range no. no. Chapter Range No. PK AV QP Carrier frequency component 2.05 Nominal 1 9 kHz - 30 MHz 1 2 on diagram-> not relevant for    passed results Remark: *.) see diagrams enclosed in Annex 1 for details Margin to Limit: Abbreviations used: M  LT  RR  C F  DF  RR : Receiver readings in dBµV/m  CF: Transducer in dB = AF (antenna factor) + CL (cable  LT  RR   AFANTENNA  Cable LOSS   DF loss)  DF : distance correction factor (if different measurement distance used than specified in the standard Remark: positive margin means passed result  LT : Limit in dBµV/m CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 14 of 30 5.1.7. Correction factors due to reduced meas. distance (f< 30 MHz) The used correction factors when the measurement distance is reduced compared to regulatory measurement distance, are calculated according Extrapolation formulas valid for EUT’s with maximum dimension of 0.625xLambda. Formula 2+3+4 as presented in ANSI C63.10, Chapter 6.4.4 are used for the calculations of proper extrapolation factors. 5.1.8. VERDICT: Limits according §15.225(a)(b)(c)(d) and RSS-210, Issue 9, Chapter B.6 - passed CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 15 of 30 5.2. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz 5.2.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA receiver  377 ESCS30  001 ESS  489 ESU 40  620 ESU 26 spectr. analys.  747 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signalling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix Car DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050   498 NGPE battery line voltage  230 V 50 Hz via public mains  060 120 V 60 Hz via PAS 5000 5.2.2. Requirements/Limits  Part 15 Subpart B, §15.109, class B FCC  Part 15 Subpart C, §15.209 @ frequencies defined in §15.205  RSS-Gen., Issue 5, Chapter 8.9, Table 5+6+7 (licence-exempt radio apparatus)  RSS-Gen., Issue 5, Chapter 7.3, Table 3 (receiver) ISED (IC)  ICES-003, Issue 6, Table 4(class A)/Table 5(Class B)  RSS-247, Issue 2, Chapter 5.5  RSS-247, Issue 2, Chapter 6.2  C63.4-2014 ANSI  C63.10-2013 Radiated emissions limits, 3 meters Frequency [MHz] QUASI Peak [µV/m] QUASI-Peak [dBµV/m] 30 - 88 100 40.0 Limit 88 - 216 150 43.5 216 - 960 200 46.0 above 960 500 54.0 CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 16 of 30 5.2.3. Restricted bands of operation (FCC §15.205/ RSS-Gen, Issue 5, Chapter 8.10, Table 7) MHz MHz GHz 0.090-0.110 156.7-156.9 9.0-9.2 0.495-0.505 162.0125-167.17 9.3-9.5 2.1735-2.1905 167.72-173.2 10.6-12.7 3.020-3.026 (Canada only) 240-285 13.25-13.4 4.125-4.128 322-335.4 14.47-14.5 4.17725 - 4.17775 399.9-410 15.35-16.2 4.20725-4.20775 608-614 17.7-21.4 5.677 - 5.683 (Canada only) 960-1240 22.01-23.12 6.215-6.218 1300-1427 23.6-24.0 6.26775-6.26825 960-1427 (only Canada) 31.2-31.8 6.31175-6.31225 1435-1626.5 36.43-36.5 8.291-8.294 1645.5-1646.5 Above 38.6 8.362-8.366 1660-1710 -- 8.37625-8.38675 1718.8-1722.2 -- 8.41425-8.41475 2200-2300 -- 12.29-12.293 2310-2390 -- 12.51975-12.52025 2483.5-2500 -- 12.57675-12.57725 2690-2900 -- 13.36-13.41 2655-2900 (only Canada) -- 16.42-16.423 3260-3267 -- 16.69475-16.69525 3332-3339 -- 16.80425-16.80475 3345.8-3358 -- 25.5-25.67 3500-4400 (only Canada) -- 37.5-38.25 3600-4400 -- 73-74.6 4500-5150 -- 74.8-75.2 5350-5460 -- 108-121.94 7250-7750 -- 123-138 8025-8500 -- 108-138 (only Canada) -- -- 149.9-150.05 -- -- 156.52475-156.52525 -- -- Remark: only spurious emissions are allowed within these frequency bands not exceeding the limits per §15.209/RSS-Gen. CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 17 of 30 5.2.4. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 0.8m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver Scan frequency range:  30 – 1000 MHz  other: (Analyzer) Settings Scan-Mode  6 dB EMI-Receiver Mode  3 dB spectrum analyser mode Detector Peak / Quasi-peak RBW/VBW 100 kHz/300 kHz Mode: Repetitive-Scan, max-hold Scan step 80 kHz Sweep-Time Coupled – calibrated display if continuous TX-signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for electric field measurement in the range 30 MHz to 1 GHz” 5.2.5. MEASUREMENT RESULTS The results are presented below in summary form only. For more information please consult the diagrams included in separate chapter in Annex 1. Diagra Set- OP- Used detector Result m No. / Frequency up mode Remark Sub- range no. no. Chapter PK AV QP EUT standing 30 MHz – 1 3.01 1 2 Control Unit (AE 2) situated    Passed GHz on the table EUT lying 30 MHz – 1 3.02 1 2 Control Unit (AE 2) situated    Passed GHz on the table Remark: -- CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 18 of 30 5.3. Frequency error (tolerance) §15.225( e) Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30     spectr. analys.  489 ESU40  584 FSU8  714 FSW  683 FSU26   antenna  048 EMCO3143  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  431 Model 7405 signaling  298 CMU  460 CMU  295 RACAL  392 MT8820A   power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  VT 4002  405 OPUS10  110 USB LWL  482 Filter Matrix  477 GPS  5.3.1. Standards and Limits: CFR 47, §15.225, ANSI 63.10: 2013 Frequency Frequency tolerance Remarks [MHz] [%] [ppm] [Hz] 13.553 -13.567 ±0.01 ±100 ±1356.7 -- 5.3.2.Test condition and measurement test set-up link to test system (if used):  air link  cable connection  EUT-grounding  none  with power supply  additional connection: between potential equalisation connector (EUT) and GND with a lab wire 1,2 m) Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver (Analyzer) Settings Span/Range: 9kHz to 150kHz; 150 kHz to 30 MHz RBW/VBW: 200Hz/auto; 10 kHz/ auto (ANSI63.10/CISPR#16) Detector/ Mode: PEAK, TRACE max-hold mode, repetitive scan for exploratory measurements 5.3.1. TEST SET-UP A sniffer antenna acts like a coupling antenna for measuring the fundamental frequency. This is placed at about 20 cm away from the equipment. Also connecting cables at the equipment are avoided on the extent possible in order not to degrade the resonance frequency of the equipment and integral antenna. 5.3.2. EQUIPMENT SETTINGS The measurements is made on nominal carrier frequency within operational band. 5.3.3. TEST METHOD If the equipment is capable of producing an un-modulated carrier then a trace with max-hold function was recorded. The maximum peak within the span was found, then the frequency deviation was recorded with the build-in frequency counter within the spectrum-analyze. The maximum resolution was chosen on the settings. The frequency deviation was recorded at switching on point of the equipment and on 2 minutes, 5minutes and 10 minutes after at in accordance with ANSI 63.10: 2013, Chapter 6.8 All measurements data are enclosed in annex measurements. Here only maximum frequency error is reported. CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 19 of 30 5.3.3.1. Frequency shift of carrier against voltage range at constant nominal temperature of 20° Celsius 1.) determine the carrier frequency for the lowest and highest channel at room temperature and nominal voltage [20°C] after a long run of the device equipment (EUT). This frequency is taken as reference for all other measured frequencies. 2.) loaded batteries with specified voltage are prepared and used in the equipment specified range of the battery and equipment declared voltage. 5.3.3.2. Frequency shift of carrier against temperature at constant power supply voltage 1.) Use a full loaded battery for tests according this chapter 2.) determine the carrier frequency at room temperature and nominal voltage [20°C] after a long run of the device equipment (EUT). This frequency is taken as reference for all other measured frequencies. 3.) Perform the carrier frequencies measurements in 10°C increments from 50°C down to -20°C as required by the standards. The stabilization period was about 1 hour after thermal reach of the required temperature. 5.3.4. Results for voltage variation Set. 3 / Op. 1 Nominal condition Vnom = 13.5 V 13.56026680 MHz Limit-> 100ppm: 1356.02668 Hz (full battery) Tnom = 21°C fMIN: 13.55891077 MHz fMAX: 13.56162283 MHz Extreme conditions Frequency Voltage Values for Frequency Error measured [V] [MHz] [Hz] [%] [ppm] VMAX 16.00 13.5602473 -20 0.000144 1.44 15.20 13.5602869 20 -0.000148 -1.48 14.30 13.5602714 5 -0.000034 -0.34 13.40 13.5602668 0 0.000000 0.00 12.50 13.5602650 -2 0.000013 0.13 11.60 13.5602649 -2 0.000014 0.14 10.70 13.5602655 -1 0.000010 0.10 9.80 13.5602667 0 0.000001 0.01 8.90 13.5602688 2 -0.000015 -0.15 VMIN 8.00 13.5602748 8 -0.000059 -0.59 VERDICT: Passed CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 20 of 30 5.3.5. Results for temperature variation Set. 3 / Op. 1 Nominal condition Vnom = 13.5V Measured Reference fMIN : 13.558911 MHz (DC Supply) 13.5602668 Limit-> 100 ppm: 1356.02668 Hz frequency [MHz] Tnom = 21°C fMAX: 13.561623 MHz Extreme conditions Abs. Absolute Measurement period Frequency Values for Frequency Error Temperature Maximum Maximum Verdict after power-up the EUT measured [Hz] [%] [ppm] Value value on StartUp 13.5601129 -153.9000000 -0.001135 -11.35 2 Minutes 13.5601074 -159.4000000 -0.001175 -11.75 Tmax=85°C 11.81 5 Minutes 13.5601066 -160.2000000 -0.001181 -11.81 10 Minutes 13.5601119 -154.9000000 -0.001142 -11.42 on StartUp 13.5601415 -125.3000000 -0.000924 -9.24 2 Minutes 13.5601245 -142.3000000 -0.001049 -10.49 T=70°C 11.57 5 Minutes 13.5601164 -150.4000000 -0.001109 -11.09 10 Minutes 13.5601099 -156.9000000 -0.001157 -11.57 on StartUp 13.5601808 -86.0000000 -0.000634 -6.34 2 Minutes 13.5601606 -106.2000000 -0.000783 -7.83 T=60°C 9.88 5 Minutes 13.5601468 -120.0000000 -0.000885 -8.85 10 Minutes 13.5601328 -134.0000000 -0.000988 -9.88 on StartUp 13.5602186 -48.2000000 -0.000355 -3.55 2 Minutes 13.5602039 -62.9000000 -0.000464 -4.64 T=50°C 7.14 5 Minutes 13.5601874 -79.4000000 -0.000586 -5.86 10 Minutes 13.5601700 -96.8000000 -0.000714 -7.14 on StartUp 13.5602325 -34.3000000 -0.000253 -2.53 2 Minutes 13.5602245 -42.3000000 -0.000312 -3.12 T=40°C 4.40 5 Minutes 13.5602173 -49.5000000 -0.000365 -3.65 10 Minutes 13.5602071 -59.7000000 -0.000440 -4.40 on StartUp 13.5602570 -9.8000000 -0.000072 -0.72 2 Minutes 13.5602553 -11.5000000 -0.000085 -0.85 T=30°C 1.47 5 Minutes 13.5602520 -14.8000000 -0.000109 -1.09 10 Minutes 13.5602469 -19.9000000 -0.000147 -1.47 19.74 Pass on StartUp 13.5604227 155.9000000 0.001150 11.50 2 Minutes 13.5604108 144.0000000 0.001062 10.62 T=10°C 11.50 5 Minutes 13.5604003 133.5000000 0.000984 9.84 10 Minutes 13.5603891 122.3000000 0.000902 9.02 StartUp 13.5604803 213.5000000 0.001574 15.74 2 Minutes 13.5604633 196.5000000 0.001449 14.49 T=0°C 15.74 5 Minutes 13.5604521 185.3000000 0.001366 13.66 10 Minutes 13.5604418 175.0000000 0.001291 12.91 StartUp 13.5605109 244.1000000 0.001800 18.00 2 Minutes 13.5604999 233.1000000 0.001719 17.19 T=-10°C 18.00 5 Minutes 13.5604932 226.4000000 0.001670 16.70 10 Minutes 13.5604874 220.6000000 0.001627 16.27 StartUp 13.5605329 266.1000000 0.001962 19.62 2 Minutes 13.5605291 262.3000000 0.001934 19.34 T=-20°C 19.62 5 Minutes 13.5605262 259.4000000 0.001913 19.13 10 Minutes 13.5605234 256.6000000 0.001892 18.92 StartUp 13.5605331 266.3000000 0.001964 19.64 2 Minutes 13.5605345 267.7000000 0.001974 19.74 T=-30°C 19.74 5 Minutes 13.5605345 267.7000000 0.001974 19.74 10 Minutes 13.5605338 267.0000000 0.001969 19.69 StartUp 13.5604862 219.4000000 0.001618 16.18 2 Minutes 13.5605053 238.5000000 0.001759 17.59 Tmin=-40°C 18.68 5 Minutes 13.5605155 248.7000000 0.001834 18.34 10 Minutes 13.5605201 253.3000000 0.001868 18.68 VERDICT: Passed CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 21 of 30 5.4. RF-Parameter - 99% occupied Bandwith 5.4.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU  683 FSU26  attenuator  530 10 dB      other EMCO  431 Model 7405 signaling  392 MT8820A  436 CMU  547 CMU DC power  463 HP3245A  087 EA3013  354 NGPE 40  086 LNG50-10   Power supply  12 V DC 060 110 V 60 Hz via PAS 5000 voltage Others  613 20dB Attenuator  cable K5 5.4.2. References of bandwidth measurements §15.215(C), RSS-Gen, Issue 5: Chapter 6.7 (c) Intentional radiators operating under the alternative provisions to the general emission limits, as contained in §§15.217 through 15.257 and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. In the case of intentional radiators operating under the provisions of subpart E, the emission bandwidth may span across multiple contiguous frequency bands identified in that subpart. The requirement to contain the designated bandwidth of the emission within the specified frequency band includes the effects from frequency sweeping, frequency hopping and other modulation techniques that may be employed as well as the frequency stability of the transmitter over expected variations in temperature and supply voltage. If a frequency stability is not specified in the regulations, it is recommended that the fundamental emission be kept within at least the central 80% of the permitted band in order to minimize the possibility of out-of-band operation. 5.4.3. Test condition and measurement test set-up Signal ink to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% General measurement procedures Please see chapter “Test system set-up for conducted RF-measurement at antenna Port” (W2 Set-up) 5.4.4. EUT Settings: The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. Different modulation characteristics have been checked, e.g. data rates which EUT can operate. 5.4.5. Measurement method: Three carrier frequencies (low/middle/high) were used for showing the compliance with this requirement. The operating modes have been varied (e.g. data rate, modulation scheme, etc.). If applicable the hopping-mode is switched off. Also the 99% emission bandwidth was measured. Two markers are placed on frequency points such that left to lower f-marker and right to higher f-marker only 1% of the TX-power is contained. Between the markers, 99% of the power is laying. The RBW value is readjusted and the measurement repeated until the RBW/EBW ratio is around 1%. 5.4.6. Spectrum-Analyzer settings: Span Set as to fully display the emissions + 30% Scale y display approximate 30 dB below the maximum PEAK level Resolution Bandwidth ANSI 63.10:2013 Set to initial value approx. 1% to 5% of the emission bandwidth, re- (RBW) adjust and proof that RBW/EBW is between 1% and 5% Video Bandwidth (VBW) Minimum 3 times the resolution bandwidth Sweep time Auto-coupled Detector Peak detector Sweep mode Repetitive Mode, MAX-HOLD, trace stabilization CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 22 of 30 5.4.7. Results: Set-up no.: 2 99% Occupied Bandwidth Op. Mode: 2 [MHz] TNOM = 21 °C Channel No. 1 Channel No. 2 VNOM = 13.5 V 1.835 -- Remark: For graphical results pls. see annex 1 to this test report. VERDICT: pass (bandwidth within designated operational band) CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 23 of 30 5.5. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it’s contribution to the overall uncertainty according it’s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based on a RF-Measurement Reference Frequency range Remarks confidence level of 95% Conducted emissions 9 kHz - 150 kHz 4.0 dB CISPR 16-2-1 - (U CISPR) 150 kHz - 30 MHz 3.6 dB Radiated emissions 30 MHz - 1 GHz 4.2 dB CISPR 16-2-3 E-Field Enclosure 1 GHz - 18 GHz 5.1 dB Disturbance power CISPR 16-2-2 30 MHz - 300 MHz - - Substitution Power Output radiated - 30 MHz - 4 GHz 3.17 dB method Cel- Cel- Set-up No. BT1 W1 W2 -- C1 C2 Power Output conducted - 9 kHz - 12.75 GHz N/A 0.60 0.7 0.25 N/A -- - 12.75 - 26.5GHz N/A 0.82 -- N/A N/A -- Conducted emissions - 9 kHz - 2.8 GHz 0.70 N/A 0.70 N/A 0.69 -- N/A - not on RF-port 2.8 GHz - 12.75GHz 1.48 N/A 1.51 N/A 1.43 -- applicable 12.75 GHz - 18GHz 1.81 N/A 1.83 N/A 1.77 -- 18 GHz - 26.5GHz 1.83 N/A 1.85 N/A 1.79 -- Power density - 1 – 2.8GHz 1.40 dB -- 0.1272 ppm (Delta Marker) Frequency Occupied bandwidth - 9 kHz - 4 GHz error 1.0 dB Power - 0.1272 ppm (Delta Marker) Frequency Emission bandwidth 9 kHz - 4 GHz error - See above: 0.70 dB Power Frequency stability - 9 kHz - 20 GHz 0.0636 ppm - 150 kHz - 30 MHz 5.0 dB Magnetic Radiated emissions 30 MHz - 1 GHz 4.2 dB field - Enclosure 1 GHz - 20 GHz 3.17 dB E-field Substitution Table: measurement uncertainties, valid for conducted/radiated measurements CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 24 of 30 6. Abbreviations used in this report The abbreviations ANSI American National Standards Institute AV , AVG, CAV Average detector EIRP Equivalent isotropically radiated power, determined within a separate measurement EGPRS Enhanced General Packet Radio Service EUT Equipment Under Test FCC Federal Communications Commission, USA IC Industry Canada n.a. not applicable Op-Mode Operating mode of the equipment PK Peak RBW resolution bandwidth RF Radio frequency RSS Radio Standards Specification, Dokuments from Industry Canada Rx Receiver TCH Traffic channel Tx Transmitter QP Quasi peak detector VBW Video bandwidth ERP Effective radiated power 7. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) FCC, Federal Communications (MRA US-EU 558 Radiated Measurements above 1 GHz, 3 m (FAR) Commission 0003) 348 Mains Ports Conducted Interference Measurements Laboratory Division, USA 348 Telecommunication Ports Conducted Interference Measurem. 337 -- Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) IC, Industry Canada Certification 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) and Engineering Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 487 R- 4452 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) VCCI, Voluntary Control Council 550 G- 20013 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) for Interference by Information 348 C- 20009 Mains Ports Conducted Interference Measurements Technology Equipment, Japan 348 T- 20006 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 25 of 30 8. Instruments and Ancillary 8.1. Used equiment “CTC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 8.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 RT Harmonics Analyzer dig. 119 B10 G60547 Firm.= V 3.1DHG Flickermeter 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. all 298 Univ. Radio Communication Tester CMU 200 832221/091 band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 System EMS 335 CTC-EMS-Conducted - EMC 32 V 8.52 Conducted 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band System EMI field 441 CTC-SAR-EMI Cable Loss - EMC 32 Version 8.52 (SAR) System EMS field 442 CTC-SAR-EMS - EMC 32 Version 8.40 (SAR) System CTC-FAR- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 9.15.00 EMI-RSE System-EMS-Field 444 CTC-FAR-EMS field - EMC 32 Version 9.15.00 (FAR) R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 607 Signal Generator SMR 20 832033/011 V1.25 620 EMI Test Receiver ESU 26 100362 4.43_SP3 Wideband Radio Communication 642 CMW 500 126089 Setup V03.26, Test programm component V03.02.20 Tester 670 Univ. Radio Communication Tester CMU 200 106833 µP1 =V8.50, Firmware = V.20 689 Vector Signal Generator SMU200 100970 02.20.360.142 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) 699 Audio Analyzer UPL16 833494/005 3.06 CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 26 of 30 8.1.2. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 12 M - 23.05.2020 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 12 M - 23.05.2020 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 23.05.2021 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 22.05.2022 36/12 020 Horn Antenna 18 GHz (Subst 1) 3115 9107-3699 EMCO - 31.07.2021 M 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 30.05.2021 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 23.05.2021 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 WRCT 1900/2200-5/40- 066 notch filter (WCDMA; FDD1) 5 Wainwright GmbH 12 M 1g 16.11.2019 10EEK 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 30.05.2021 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 30.05.2021 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 RT Harmonics Analyzer dig. 119 B10 G60547 BOCONSULT 36 M - 22.05.2022 Flickermeter 133 horn antenna 18 GHz (Meas 1) 3115 9012-3629 EMCO 36 M 1c 10.03.2020 134 horn antenna 18 GHz (Subst 2) 3115 9005-3414 EMCO 36 M - 10.03.2020 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 30.05.2020 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 30.05.2020 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 30.05.2020 266 Peak Power Sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 30.05.2020 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 AMF-2D-100M4G-35- 287 pre-amplifier 25MHz - 4GHz 379418 Miteq 12 M 1c 16.11.2019 10P 291 high pass filter GSM 850/900 WHJ 2200-4EE 14 Wainwright GmbH 12 M 1c 16.11.2019 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 12 M - 22.05.2020 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 14.03.2020 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 20.03.2020 331 Climatic Test Chamber -40/+180 Grad HC 4055 43146 Heraeus Vötsch 24 M - 10.01.2021 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 30.05.2020 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 23.05.2021 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 21.05.2021 371 Bluetooth Tester CBT32 100153 R&S 36 M - 30.05.2019 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 12 M - 22.05.2020 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 22.05.2020 389 Digital Multimeter Keithley 2000 0583926 Keithley pre-m - 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 01.07.2020 396 Thermo/Hygrometer Thermo/Hygrometer - Conrad 24 M - 09.01.2021 126.0604.0003.3.3.3. LUFFT Mess u. 405 Thermo-/Hygrometer OPUS 10 THI 24 M - 16.05.2021 22 Regeltechnik GmbH 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 25.05.2020 439 UltraLog-Antenna HL 562 100248 Rohde & Schwarz 36 M - 10.03.2020 System EMI field (SAR) 441 CTC-SAR-EMI Cable Loss - CETECOM 12 M 5 05.06.2017 Cable CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 27 of 30 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due System CTC-FAR-EMI- ETS-Lindgren / 443 CTC-FAR-EMI-RSE - 12 M 5 16.11.2019 RSE CETECOM WRCT 1850.0/2170.0- Wainwright 448 notch filter WCDMA_FDD II 5 12 M 1c 16.11.2019 5/40-10SSK Instruments GmbH WRCT 824.0/894.0-5/40- 449 notch filter WCDMA FDD V 1 Wainwright 12 M 1c 16.11.2019 8SSK 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 30.05.2020 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 30.05.2020 467 Digital Multimeter Fluke 112 89680306 Fluke USA 36 M - 30.05.2021 468 Digital Multimeter Fluke 112 90090455 Fluke USA 36 M - 30.04.2021 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 30.05.2021 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d AMF-5D-02501800-25- 484 pre-amplifier 2,5 - 18 GHz 1244554 Miteq 12 M - 16.11.2019 10P System CTC NSA-Verification SAR- System EMI field (SAR) ETS Lindgren / 487 - 24 M - 16.04.2021 EMI NSA CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 30.06.2020 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- WRCG 824/849-814/859- 503 band reject filter SN 5 Wainwright pre-m 2 60/10SS WRCA 800/960-02/40- 512 notch filter GSM 850 SN 24 Wainwrght 12 M 1c 16.11.2019 6EEK HF Relais Box Keithley 517 relais switch matrix SE 04 Keithley pre-m 2 System 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 23.05.2021 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 10 dB Broadband resistive power 530 R 416110000 LOT 9828 - pre-m 2 divider 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 30.07.2019 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 30.07.2019 36/12 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz - 31.07.2021 M System CTC S-VSWR Verification System EMI Field SAR ETS 550 - 24 M - 30.08.2019 SAR-EMI S-VSWR Lindgren/CETECOM 552 high pass filter 2,8-18GHz WHKX 2.8/18G-10SS 4 Wainwright 12 M 1c 16.11.2019 557 System CTC-OTA-2 R&S TS8991 - Rohde & Schwarz 12 M 5 24.01.2020 System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 08.08.2019 VSWR 36/12 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia - 03.05.2022 M 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz pre-m - 594 Wideband Radio Communication Tester CMW 500 101757 Rohde & Schwarz 12 M - 26.06.2020 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz pre-m - 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 30.05.2021 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 30.05.2020 617 Power Splitter/Combiner ZFSC-2-2-S+ S F987001108 Mini Circuits - 2 618 Power Splitter/Combiner 50PD-634 600994 JFW Industries USA - 2 619 Power Splitter/Combiner 50PD-634 600995 JFW Industries, USA - 3 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 30.05.2020 621 Step Attenuator 0-139 dB RSP 100017 Rohde & Schwarz pre-m 2 625 Generic Test Load USB Generic Test Load USB - CETECOM - 2 634 Spectrum Analyzer FSM (HF-Unit) 826188/010 Rohde & Schwarz pre-m 2 HDMI cable with 637 High Speed HDMI with Ethernet 1m - KogiLink - 2 Ethernet 1m HDMI cable with 638 HDMI Kabel with Ethernet 1,5 m flach - Reichelt - 2 Ethernet 1,5m 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 Certified HDMI cable 641 HDMI cable with Ethernet - PureLink - 2 with 644 Amplifierer ZX60-2534M+ SN865701299 Mini-Circuits - - 670 Univ. Radio Communication Tester CMU 200 106833 Rohde & Schwarz 24 M - 30.05.2020 671 DC-power supply 0-5 A EA-3013S - Elektro Automatik pre-m 2 678 Power Meter NRP 101638 Rohde&Schwarz pre-m - 683 Spectrum Analyzer FSU 26 200571 Rohde & Schwarz 12 M - 30.05.2020 CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 28 of 30 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 687 Signal Generator SMF 100A 102073 Rohde&Schwarz 12 M - 30.05.2020 688 Pre Amp JS-18004000-40-8P 1750117 Miteq pre-m - 690 Spectrum Analyzer FSU 100302/026 Rohde&Schwarz 24 M - 30.05.2021 691 OSP120 Base Unit OSP120 106833 Rohde & Schwarz 12 M - 30.05.2020 692 Bluetooth Tester CBT 32 100236 Rohde & Schwarz 36 M - 29.05.2020 CTC-Radio Lab 693 TS8997 - Rohde&Schwarz 12 M 5 07.01.2020 1_TS8997 697 Power Splitter ZN4PD-642W-S+ 165001445 Mini-Circuits - 2 701 CMW500 wide. Radio Comm. CMW500 158150 Rohde & Schwarz 24 M - 30.07.2020 MA 4010-KT080-XPET- MA4170-KT100- 703 INNCO Antennen Mast INNCO pre-m - ZSS3 XPET-ZSS3 CO3000/933/384105 INNCO Systems 704 INNCON Controller CO 3000-4port pre-m - 16/L GmBh 711 Harmonic Mixer 90 GHz - 140GHz RPG FS-Z140 101004 RPG 36 M - 22.02.2020 712 Harmonic Mixer 75 GHz - 110GHz FS-Z110 101468 Rohde & Schwarz 36 M - 22.02.2020 713 Harmonic Mixer, 50 GHz - 75GHz FS-Z75 101022 Rohde & Schwarz 24 M - 05.07.2021 714 Signal Analyzer 67GHz FSW67 104023 Rohde & Schwarz 24 M - 04.07.2021 RPG Radiometer 715 Harmonic Mixer, 140 GHz - 220GHz FS-Z220 101009 36 M - 03.08.2020 Physics RPG Radiometer 716 Harmonic Mixer 220 GHz to 325 GHZ FS-Z325 101005 36 M - 13.02.2020 Physics 748 Pickett-Potter Horn Antenna FH-PP 4060 010001 Radiometer Physiscs 36 M - 750 Pickett-Potter Horn Antenna FH-PP 220 010011 Radiometer Physics 36 M - 751 Digital Optical System optoCAN-FD Transceiver 17-010416 mk-messtechnik GmbH - - 752 Digital Optical System optoCAN-FD Transceiver 17-010083 mk-messtechnik GmbH - - 753 Digital Optical System optoCAN-FD Transceiver 17-010084 mk-messtechnik GmbH - - 754 Digital Optical System optoCAN-FD Transceiver 17-010415 mk-messtechnik GmbH - - optoLAN-100-MAX 755 Digital Optical System 17-010795 mk-messtechnik GmbH - - Transceiver WIDEBAND RADIO 757 CMW500 163673 Rohde&Schwarz 12 M - 30.05.2020 COMMUNICATION Elektro-Automatik 781 Power Supply PS 2042-10 B 2815450369 - - GmbH &Co.KG lektro-Automatik 782 Power Supply PS 2042-10 B 2815450348 - - GmbH &Co.KG 783 Spectrum Analyzer FSU 26 100414 Rohde & Schwarz 12 M - 30.05.2020 784 Power Supply NGSM 32/10 00196 Rohde & Schwarz 12 M - RF Step Attenuator 785 RSP 860712/012 Rohde & Schwarz 12 M - 0…139.9dB 786 SAR Probe ES3DV3 3340 Speag 36 M - 14.02.2021 787 OSP OSP B157WX 101264 Rohde & Schwarz 24 M - 30.05.2020 Seibersdorf 788 Precision Omnidirectional Dipole POD 618 6182558/Q 36 M - 30.06.2021 Labaratories Seibersdorf 789 Precision Omnidirectional Dipole POD 16 162496/Q 36 M - 30.06.2021 Laboratories Antenna System 790 Horn Antenna ASY-SGH-124-SMA 29F14182337 36 M - 08.10.2021 Solutions 791 Pickett-Potter Horn Antenna FH-PP-325 10024 Radiometer Physics 36 M - 792 Pickett-Potter Horn Antenna FH-PP 075 10006 Radiometer Physics 36 M - 793 Pickett-Potter Horn Antenna FH-PP 140 10008 Radiometer Physics 36 M - 794 Pickett-Potter Horn Antenna FH-PP 110 10014 Radiometer Physics 36 M - 795 SGH Antenna SGH-26-WR10 1144 Anteral S.L. 36 M - 798 WR-22 Rectangular Gain Horn SAR-2309-22-S2 13254-01 SAGE Millimeter, Inc. 36 M - 799 Transceiver optoLAN-Gb 18-014746 mk messtechnik pre-m - 801 Spectrum Analyzer FSP 13 100960 Rohde & Schwarz 24 M - 14.01.2021 NARDA Safety 802 Exposure Level Tester ELT-400 O-0026 24 M - 30.01.2021 Solutions Narda Safety Test 803 Probe ELT probe 3cm² O-0026 24 M - 30.01.2021 Solution 805 Thermo-Hygrometer Web-Thermo-Hygrometer 02749814 W&T 24 M - 806 AC2600 Smart Wifi Router Netgear Nighthawk x4S 5K5188590067B Netgear - - Direct Coupler C-05020- 807 Direct Coupler 511 ET Industries - - 10 808 Diode Power Sensor NRV-Z1 829894/001 Rohde & Schwarz 24 M - 24.05.2021 Pasternack Enterprises 809 Standard gain Horn Antenna WR-159 Horn Antenna - - - Inc. CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 29 of 30 8.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibrationequipment Ancillary of this equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months, between this every 12 months internal validation 36/12 M Calibration every 36 months, between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration CETECOM_TR17_1_0133807T02a

Test Report 17-1-0133807T02a, Page 30 of 30 9. Versions of test reports (change history) Version Applied changes Date of release -- Initial release 2019-10-25 -- -- -- -- -- -- -------------------- End of the Test Report -------------------- CETECOM_TR17_1_0133807T02a


Document Created: 2019-10-25 13:37:42
Document Modified: 2019-10-25 13:37:42
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC