User Manual

FCC ID: UP5AT8100

Users Manual

Download: PDF
FCCID_749517

AT 8000 Series fast installation guide Welcome to AT 8000 Series Step 5: Installing one sensor into wheel Tire Pressure Monitoring Please get help from professional tire shops if necessary. System (TPMS). This Fast 1. Remove the wheel installation Guide is intended from vehicle, to give you a fast overview of Deflate, and the key steps required to separate rim and install your AT 8000 Serial tire. TPMS. For more detailed 2. Fix sensor on rim. information, please refer to the 3. Assemble rim and 8000 Serial TPMS Installation tire, inflate to Guide. typical pressures. 4. Balance wheel and Installation steps: install to vehicle. Step 1: Check components 5. Use receiver to search ID of this wheel again, and assign this ID to the position respect to this tire installation. Make sure that the sensor inside tire was keeping work well. Steps 6: Continue to install all other sensors with the same procedure. Install all tires to the right positions of vehicle. Using receiver to search and assign all IDs to correct position respect to tire installation. Steps 7: Setup pressure and temperature thresholds according to tire type.  Do not mix up each tire’s ID, or the detected tire parameter Step 2: Check identification number may not be correct!  It is easy to identify each tier’s ID by changing its pressure Each sensor should be (slightly deflate) and monitor the receiver for checking this assigned a unique pressure variation and tire position. identification number  Check all recorded tire IDs by press Key 1. Each single press on (ID), which was marked Key 1 can call one tire parameters out, including temperature, on the top of sensor. pressure, and identification code. Continually press on Key 1 can Step 3: Enable and Test read tire parameters one by one. sensors before installing To enable a sensor, it is only needed to pull out the jumper attached on sensor. After successfully enabled, sensor will start to measure environment air pressure and temperature and send them to receiver. Step 4: Set up the receiver Key1 Key2 Key3 Key4 Plug the attached power cord into Receiver and insert the other terminal to the cigarette electrical socket of vehicle. You can adjust parameters  Typical torque of new valve nut is 3~5 N-m(30~50 kgf-cm). of receiver according to your requirement.  In order to guarantee sealing, be sure that the rubber rings are  Only the first two and last four digitals of ID will show on panel properly positioned between rim and valve. of receiver, for example, if ID is 34125678, only345678 will be shown. Valve nut

Receiver Setting Setup Temperature limits Panel Setting tire Numeric row 1 Receive Status Numeric row 2 High/Low limit indication Alarm Temperature unit Temperature limit Pressure unit Status displayer - Numeric row 3 + Select tuning item Key 1 Key 2 Key 3 Key 4 Setup Pressure limits RF Symbol Alarm Setting tire High/Low limit indication Tire 1 Tire 2 Pressure limit Tire 4 Tire 3 - + Modes In order to integrate friendly operation interface and powerful parameter Select tuning item adjusting function, AT8000 contains four major operation modes, and it is easy to switch between them by press Key 4 over 0.5 second: Tire ID search and assign ↓ Working mode Step 1: Switch into ID search mode by: ↓ Setup Temperature limits 1. Press Key 4 into Tire ID search and assign ↓ Setup Pressure limits mode. 2. Press Key 1 Tire ID search and assign confirm to search. 22 11 Working mode Key functions: Step 2: Waiting for ID search Selected ID PSI/KPA ℉/℃ One ID had been searched First received ID was selected Select tire Display Step 3: Assign searched ID to exact position Graphic display ID assigned Tire Tire ID Select ID from Selected Tire for ID buffer. Temperature assigning The third of six ID. Pressure Press to assign ID Select Tire to assign ID

FCC Notice: Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 910805 2


Document Created: 2006-12-11 13:32:40
Document Modified: 2006-12-11 13:32:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC