Users Manual

FCC ID: UP5-AT63

Users Manual

Download: PDF
FCCID_3116055

AT63 sensor User’s guide 1. Introduction 3.1.2 Remove original valve cap and screw lock nut (1) This AT63 BLE sensor is a type of sensor that and will become (2). Screw the Sensor onto valve stem combined TPMS and cellphone. AT63 TPMS external clockwise (3). Screw (1) lock nut back and use wrench sensor adapts BLE low energy transmission, let driver to lock tightly (4). (3)(4) steps could effectively prevents understand tire situation through cellphone. When the sensor from removing. system detects tire pressure or temperature abnormal situation, it (APP) will directly alarm the driver. About This Manual：  The information in this manual is subject to change without notice. 3.1.3 The sensor label already indicates the sensor ID  This manual has been created with extra care. In case and its wheel order, please follow the wheel order to that you have any comments or questions regarding install sensors. this manual, please contact your local dealer or our Customer Service Center.  Before operating this set, please fully understand the EX : prerequisite such as specifications or constraints of Sensor Model: AT63 ID:810C619A the hardware and software. We are not responsible and have no liability for any loss, damage or injury as a result of misuse. Note： 2. Check Accessories (1) Beware of the conductivity between the sensor Model Photograph and valve stem. (2) Sensors are supposed to be well locked valve AT63 sensor stem to avoid from leaking. (3) Please replace original manufacturer’s sensor Battery battery in case voltage is below 2.7v. (4)External sensor will transmit data every 58~62 Lock nut seconds when the vehicle is running, and when the vehicle stops, the sensor will transmit data every 148~152 seconds. Wrench Userguide 3. System installation 3.1 Install sensor(battery changeable) 3.1.1 Place batteries into the sensor and screw the top cap off. Please attend to the electrode of the battery. Copyright (C) ATBS Technology Co. R7 版權所有請勿翻印

4. iTPMS APP Installation: 4.2 App Operating 4.2.1 Click below ID, and enter the ID learning page, start iTPMS App is for free. Through the iTPMS you can know to learn the sensor ID. tire temperature and pressure, sensor battery voltage, and each sensor’s ID. 4.1 Install APP (Take IOS as example) 4.1.1 Download the APP: iTPMS BLE from Apple Store or Google Play. 4.1.2 Go to Setting => General => Bluetooth Page. 4.1.3 Turn on the Bluetooth Note: When the above BLE words light up, then it represents it detects AT63’s signal already. 4.2.2 Place batteries into the sensor properly. When 4.1.4: Turn on the Bluetooth, and it will scan the devices sensor detects pressure, ID will turn to red to alert the automatically. user. 4.1.5 Install battery properly, and then enter to the sensor ID setting pages. After setting the ID properly, it will 4.2.3 Enter Setup page, users can set up the unit and limit read the tire data immediately. of tire pressure and temperature. Copyright (C) ATBS Technology Co. R7 版權所有請勿翻印

4.2.4 In the meantime, this TPMS program also afford user to B) Steps for scanning QR Code: manual input the ID function and scanning QR function, 1) Click middle QR buttom please refer to the following steps: 2) Enter into ID Read page, and click the blank to start A) Manual key in ID steps: scanning QR code. And then click save. 1) Click the right upper “Edit” 2) Turn to New page 3) Click the blank and appear keyboard, enter the ID and 3) Click “Yes” 4) Click SAVE and then click save. click yes, and it’s done. 4) Click “Yes” Note: Click Cancel and back to learn ID page. 5) Click SAVE and then click yes, and it’s done. Note: Be sure you already turn on the Bluetooth 5. Specification 5.1 AT63 Sensor Model AT63 Operation -40℃~ 85℃ Temperature Operation 100%, IP 68 Humidity Total Outer 22±0. 2mm meter Total Height 21±0. 2mm Copyright (C) ATBS Technology Co. R7 版權所有請勿翻印

Weight 9.79 (+0.5g) process of power supply will cause malfunction. Please Battery Around 12 months lifespan use the certified battery. Improper battery or wrong Battery size CR1632 for TPMS spec procedures will affect efficiency or cause malfunction of Monitoring 0 ~900kpa +7Kpa ( 0—130psi +1Psi) pressure sensors. Monitoring 49°C~85°C +1°C 6.12 Please observe tire pressure, temperature and temperature Frequency 2.4GHz battery voltage at all times. If the receiver cannot get the Others When a tire stops, it transmits every 150 seconds (+2 seconds). If not, it transmits every information for a long time, please check your sensors. 60 Seconds (+2 seconds) 6.13 FCC Notice Federal Communication Commission Interference 6. Caution: Statement 6.1 Information provided in user‘s guide is for reference This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to only. You should operate the device only when your Part 15 of the FCC Rules. These limits are designed vehicle stops. to provide reasonable protection against harmful interference in a residential installation. This 6.2 This product may be interrupted by some harmful equipment generates, uses, and can radiate radio system and may lead to malfunction. frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 6.3 In order to install internal sensor properly, users are interference to radio communications. However, there is no guarantee that interference will not occur in a suggested to body shop for assistance. Please beware of particular installation. If this equipment does cause the location of each sensor. Do not beat the valve directly harmful interference to radio or television reception, which can be determined by turning the equipment off or use any tools to harm the valve. and on, the user is encouraged to try to correct the 6.4 Four sensors‘ IDs of this product have already set by interference by one or more of the following measures: * Reorient or relocate the receiving antenna. the manufacturer. If you would like to replace new * Increase the separation between the equipment and sensors, please seek the agent for assistance. receiver. + Connect the equipment into an outlet on a circuit 6.4 Do not soak our product or sensor in the water or different from that to which the receiver is connected. + Consult the dealer or an experienced radio/TV chemical. Chemicals are not allowed to clean. technician for help. 6.5 Do not use water or chemicals to clean or soak the FCC Radiation Exposure Statement: receiver and sensors directly. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be 6.6 Do not replace the rubber gasket arbitrarily. If there is installed and operated with minimum distance 20cm between the any damage, please replace it with the certified one. radiator & your body. 6.7 The warranty of the product is one year, please use Notice: Any modifications or any system the product correctly. The warranty excludes natural and alterations cannot guarantee the user‘s rights is artificial disasters, drops, soaking in water accident, fire protected continuously. accident, anomalistic power supply and other damages. 6.8 The warranty won‘t cover any consumptive accessories like: the packaging, Velcro, manual, etc. 6.9 Please refer to the steps from user‘s guide to avoid any abnormal operation. It may lead to malfunction. 6.10 Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. 6.11 Please follow the instruction of power supply. Wrong Copyright (C) ATBS Technology Co. R7 [aeen


Document Created: 2016-08-30 11:57:04
Document Modified: 2016-08-30 11:57:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC