User Manual-2

FCC ID: UMPTX141

Users Manual

Download: PDF
FCCID_4343740

TX140 Remote Electronic Ignition and Control System OPERATING INSTRUCTIONS -FOR OEM USE ONLY NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This de- vice may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency ener- gy and, if not installed and used in accordance with the instruc- TX140 tions, may cause harmful interference to radio communications. ⚠ WARNING However, there is no guarantee that interference will not occur in Fire or explosion hazard. Attempted disassembly or repair a particular installation. If this equipment does cause harmful in- of controls can cause property damage, severe injury or terference to radio or television reception, which can be deter- death. Do not disassemble the gas valve; it contains no ser- mined by turning the equipment off and on, the user is encour- viceable components. aged to try to correct the interference by one or more of the follow- Read these instructions carefully. Failure to follow them ing measures: could result in a fire or explosion causing property dam- —Reorient or relocate the receiving antenna. age, personal injury, or loss of life. The product must be installed —Increase the separation between the equipment and receiver. and operated according to all local regulations. —Connect the equipment into an outlet on a circuit different from A. that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. ● Do not light any appliance. NOTE: This device complies with CAN ICES-3 (B)/NMB-3(B) ● Do not touch any electrical switch; do not use any ◆ This product meets the applicable Innovation, Science and phone in your building. ● Economic Development Canada technical specifications. Ce produit repond aux specifications techniques applicables a ● If you cannot reach the gas supplier, call the fire de- l'innovation, Science et Developpement economique Canada. partment. ◆ Canadian Compliance Statement This device complies with Industry Canada license-exempt B. Use only your hand to push in or turn the gas control knobs. Never use tools. If a knob will not push in or turn RSSs. Operation is subject to the following two conditions: by hand, don’t try to repair it, call a qualified service tech- 1) This device may not cause interference, and nician. Force or attempted repair may result in a fire or 2) This device must accept any interference, including explosion. interference that may cause undesired operation of the C. Do not use this control or any gas appliance if any part has device. been under water or in contact with water. Immediately call Le present appareil est conforme aux CNR d’Industrie Canada a qualified service technician to replace the control sys- applicables aux appareils radio exempts de licence. L’exploita- tem and any gas control system which has been under water or in contact with water. tion est autorisee aux deux conditions suivantes : 1) l’appareil ne doit pas produire de brouillage; D. These instructions are to be referenced as a user guide, 2) l’utilisateur de l’appareil doit accepter tout brouillage and do not supersede appliance manufacturer’s lighting instructions. radioelectrique subi, meme si le brouillage est suscepti- ble d’en compromettre le fonctionnement. APPLICATION Batteries - Remote Handset: TX140 is a battery-powered electronic remote ignition and 3 x1.5V “AAA” (quality alkaline recommended) control system for gas appliances with pilot burners and ODS systems. 4.5V 100mA GENERAL NOTES NOTE: These remote handsets, receiver, wall switches, are not in- Radio frequency Remote terchangeable with previous versions. 434 MHz for Europe, US, Canada; For all lighting/ignition instructions please refer to appliance manu- facturer’s instructions. 1/4

TX140—Operating Instructions D03 TX140 SERIES REMOTE HANDSET FEATURES TX120 TX140 TX141 Remote 434MHz Controller TX120 TX140 TX141 Unidirectional Model ON/ OFF ★ ★ ★ Childproof ★ ★ ★ Revo Home Compatible ★ ★ ★ Flame Height Adjustment ★ ★ Standing Pilot* ★ LCD Low Battery Indicator Second Burner Thermostat Timer Error Code Notification* Fan Speed ★ Light Dimmer AUX ON/ OFF Fan Delay ON/ OFF Clock Daily Program Thermostat 3 Independent Access Keys *Disabled for Europe 2/4

TX140—Operating Instructions D03 CHILDPROOF FLAME HEIGHT ADJUSTMENT There’s a slide switch can select Handset lock or unlock. During the appliance flame on, briefly Lock: The handset is rendered in- pressing the button changes the operable include the off function. flame height in the following order: Flame height 3 2 1 and back to 3. TURN OFF THE FIRE Wiring of valve and receiver must be completed be- Press button, fore starting ignition. Failure to do so could damage the electronics. NOTE: There is a 3 second delay ⚠ WARNING before the next ignition is possible. When pilot ignition is confirmed, main flame valve turn on to maximum flame height. PILOT FLAME Handset Press button to activate appliance to pilot flame. FAN SPEED ADJUSTMENT Press button to deactivate appli- Handset ance to pilot flame. During the appliance flame on, briefly pressing the button changes the fan speed of thermostat in the follow- ing order: Fan speed 3 2 1 0 and back to Fan speed 3 TURN ON THE FIRE Press button, the ● Main burner and rear burner turn on once pilot ignition is confirmed. ● Main gas goes Max flame height first, MISCELLANEOUS and will goes last flame height memory. Battery replacement Battery replacement is recommended at the beginning of each heating season. Do not use metal tools to remove bat- teries. Using a metal tool could cause a short that may damage the receiver. Dexen Industries, Inc 9220 Norwalk Blvd Santa Fe Springs, CA 90670 Tel: +1 5626998490 3/4


Document Created: 2018-12-18 17:39:34
Document Modified: 2018-12-18 17:39:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC