TEST REPORT

FCC ID: UG9UBHS-PH1

Test Report

Download: PDF
FCCID_827878

Ref. No.: LR500190707E 243 Jubug-Ri,Yangji-Myeon, Yongin-Si, Gyeonggi-Do, Korea 449-822 Tel: +82-31-323-6008 Fax: +82-31-323-6010 http://www.ltalab.com Dates of Tests: July 24 ~ 31, 2007 Test Report S/N: LR500190707E Test Site : LTA CO., LTD. CERTIFICATIO OF COMPLIANCE FCC ID. UG9UBHS-PH1 APPLICANT Ubixon Co., Ltd. FCC Classification : FHSS Sequence Spread Spectrum (FHSS) Manufacturing Description : Bluetooth Stereo Headset Manufacturer List : Ubixon Co., Ltd. Model name : UBHS-PH1 Test Device Serial No.: : Identical prototype Rule Part(s) : FCC Part 15.247 Subpart C; ANSI C-63.4-2003 Frequency Range : 2402 ~ 2480MHz RF power Class : 2 (-6dBm ~ +4dBm) Data of issue : July 31, 2007 This test report is issued under the authority of: The test was supervised by: Dong –Min JUNG, Technical Manager Kyung-Taek LEE, Test Engineer This test result only responds to the tested sample. It is not allowed to copy this report even partly without the allowance of the test laboratory. This report must not be used by the applicant to claim product endorsement by any agency. NVLAP LAB Code.: 200723-0 Copyright ○ c 2007, LTA Co., Ltd. Page 1 of 30

Ref. No.: LR500190707E TABLE OF CONTENTS 1. GENERAL INFORMATION’S -------------------------------------------------------------------------- 3 2. INFORMATION’S ABOUT TEST ITEM ------------------------------------------------------------- 4 3. TEST REPORT --------------------------------------------------------------------------------------------- 5 3.1 SUMMARY OF TESTS ------------------------------------------------------------------------------ 5 3.2 TECHNICAL CHARACTERISTICS TEST ------------------------------------------------------- 6 3.2.1 CARRIER FREQUENCY SEPARATION ---------------------------------------------------- 6 3.2.2 NUMBER OF HOPPING FREQUENCIES -------------------------------------------------- 8 3.2.3 20 dB BANDWIDTH ---------------------------------------------------------------------------- 11 3.2.4 TIME OF OCCUPANCY (Dwell Time) ------------------------------------------------------- 13 3.2.5 TTANSMITTER OUTPUT POWER ---------------------------------------------------------- 15 3.2.6 BAND – EDGE ----------------------------------------------------------------------------------- 17 3.2.7 FIELD STRENGTH OF HARMONICS ------------------------------------------------------ 23 3.2.8 AC CONDUCTED EMISSIONS -------------------------------------------------------------- 26 APPENDIX APPENDIX TEST EQUIPMENT USED FOR TESTS -------------------------------------------- 29 Copyright ○ c 2007, LTA Co., Ltd. Page 2 of 30

Ref. No.: LR500190707E 1. General information’s 1-1 Test Performed Company name : LTA Co., Ltd. Address : 243, Jubug-ri,Yangji-Myeon,Youngin-Si, Kyunggi-Do, Korea. 449-822 Web site : http://www.ltalab.com E-mail : chahn@ltalab.com Telephone : +82-31-323-6008 Facsimile +82-31-323-6010 Quality control in the testing laboratory is implemented as per ISO/IEC 17025 which is the “General requirements for the competents of calibration and testing laboratory”. 1-2 Accredited agencies LTA Co., Ltd. is approved to perform EMC testing by the following agencies: Agency Country Accreditation No. Validity Reference NVLAP U.S.A 200723-0 2007-09-30 ECT accredited Lab. RRL KOREA KR0049 2009-06-20 EMC accredited Lab. FCC U.S.A 610755 2008-03-28 FCC filing VCCI JAPAN R2133, C2307 2008-06-22 VCCI registration IC CANADA IC5799 2008-04-23 IC filing Copyright ○ c 2007, LTA Co., Ltd. Page 3 of 30

Ref. No.: LR500190707E 2. Information’s about test item 2-1 Applicant & Manufacturer Company name : Ubixon Co., Ltd. Address : 801, Ssanglim Bldg, 151-11, Ssanglim-dong, Chung-gu Seoul, Korea 100-400 Tel / Fax : +82-2-6320-0190 / +82-2-6320-0198 2-2 Equipment Under Test (EUT) Trade name : Digital Audio Player FCC ID : UG9UBHS-PH1 Model name : UBHS-PH1 Serial number : Identical prototype Date of receipt : July 23, 2007 EUT condition : Pre-production, not damaged Antenna type : PCB Pattern antenna Max. Gain: 0.65dBi Frequency Range : 2402 ~ 2480MHz RF output power Range : -6dBm~+4dBm (Class 2) Number of channels : 79 Channel spacing : 1MHz Channel Access Protocol : Frequency Hopping Type of Modulation : GFSK Power Source : 3.7V (Li-Polymer Rechargeable) (Recharging – by USB Cable) 2-3 Tested frequency LOW MID HIGH Frequency (MHz) 2402 2441 2480 2-4 Ancillary Equipment – Bluetooth Equipment Model No. Serial No. Manufacturer earphone N/A N/A N/A - - - - 2-5 Ancillary Equipment – Bluetooth + Charging mode Equipment Model No. Serial No. Manufacturer PC dx2200Microtower CNG6500RX9 HP Monitor VS11353 E060T4021/1-1 View Sonic Keyboard SK-8115 641-OEWW DELL Mouse MO56UO 510022473 DELL Print Deskjet 600K SG7631B1XX HP earphone N/A N/A N/A - - - - Copyright ○ c 2007, LTA Co., Ltd. Page 4 of 30

Ref. No.: LR500190707E 3. Test Report 3.1 Summary of tests FCC Part Test Status Parameter Limit Section(s) Condition (note 1) 15.247(a) Carrier Frequency Separation > 25 kHz C 15.247(a) Number of Hopping Frequencies > 75 hops C 15.247(a) 20 dB Bandwidth < 1 MHz C 15.247 Dwell Time < 0.4 seconds Conducted C 15.247(b) Transmitter Output Power < 1Watt C 15.247(d) Conducted Spurious emission > 20 dBc C 15.247(d) Band Edge > 20 dBc C < 54 dBuV 15.249 / 15.209 Field Strength of Harmonics C (at 3m) Radiated 15.109 Field Strength - C 15.207 /15.107 AC Conducted Emissions EN 55022 Line Conducted C 15.203 Antenna requirement - - C Note 1: C=Complies NC=Not Complies NT=Not Tested NA=Not Applicable Note 2: The data in this test report are traceable to the national or international standards. The sample was tested according to the following specification: FCC Parts 15.247; ANSI C-63.4-2003 Æ Antenna Requirement The Ubixon co.,ltd. UBHS-PH1 unit complies with the requirement of §15.203. The antenna is PCB Pattern antenna. Copyright ○ c 2007, LTA Co., Ltd. Page 5 of 30

Ref. No.: LR500190707E 3.2 Transmitter requirements 3.2.1 Carrier Frequency Separation Procedure: The carrier frequency separation was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function enabled. After the trace being stable, the reading value between the peaks of the adjacent channels using the marker-delta function was recorded as the measurement results. The spectrum analyzer is set to: Span = 3 MHz (wide enough to capture the peaks of two adjacent channels) RBW = 30 kHz (1% of the span or more) Sweep = auto VBW = 30 kHz Detector function = peak Trace = max hold Measurement Data: Test Results Carrier Frequency Separation (MHz) Result 0.997 Complies - See next pages for actual measured spectrum plots. Minimum Standard: The EUT shall have hopping channel carrier frequencies separated by a minimum of 25kHz or the 20dB bandwidth of the hopping channel, whichever is greater. Measurement Setup EUT Spectrum Analyzer Coax cable Figure 1: Measurement setup for the carrier frequency separation Copyright ○ c 2007, LTA Co., Ltd. Page 6 of 30

& n a coor ns fer s .o don at 2e se 1150 rerw vee 1 M drten fie & un se S1rl cora cerre pemtuons seur Res oi do uie aven so «x She sugee 2000 mz Vise ®

Ref. No.: LR500190707E 3.2.2 Number of Hopping Frequencies Procedure: The number of hopping frequencies was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function enabled. To get higher resolution, four frequency ranges within the 2400 ~ 2483.5 MHz FH band were examined. The spectrum analyzer is set to: Frequency range 1: Start = 2389.5MHz, Stop = 2414.5 MHz 2: Start = 2414.5MHz, Stop = 2439.5 MHz 3: Start = 2439.5MHz, Stop = 2464.5 MHz 4: Start = 2464.5MHz, Stop = 2489.5 MHz RBW = 300 kHz (1% of the span or more) Sweep = auto VBW = 300 kHz (VBW ≥ RBW) Detector function = peak Trace = max hold Span = 25MHz Measurement Data: Complies Total number of Hopping Channels 79 - See next pages for actual measured spectrum plots. Minimum Standard: At least 15 hopes Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2007, LTA Co., Ltd. Page 8 of 30

Ref. No.: LR500190707E Number of Hopping Frequencies Copyright ○ c 2007, LTA Co., Ltd. Page 9 of 30

Ref. No.: LR500190707E Number of Hopping Frequencies Copyright ○ c 2007, LTA Co., Ltd. Page 10 of 30

Ref. No.: LR500190707E 3.2.3 20 dB Bandwidth Procedure: The bandwidth at 20 dB below the highest inband spectral density was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function disabled at the highest, middle and the lowest available channels.. After the trace being stable, Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 20dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is ( as close as possible to ) even with the reference marker level. The marker-delta reading at this point is the 20 dB bandwidth of the emission. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest channels Span = 2 MHz (approximately 2 or 3 times of the 20 dB bandwidth) RBW = 30 kHz Sweep = auto VBW = 30 kHz (VBW ≥ RBW) Detector function = peak Trace = max hold Measurement Data: Frequency Test Results Channel No. (MHz) Measured Bandwidth (MHz) Result 2402 0 0.945 Complies 2441 39 0.930 Complies 2480 78 0.937 Complies - See next pages for actual measured spectrum plots. Minimum Standard: N/A Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2007, LTA Co., Ltd. Page 11 of 30

Ref. No.: LR500190707E 20 dB Bandwidth Copyright ○ c 2007, LTA Co., Ltd. Page 12 of 30

Ref. No.: LR500190707E 3.2.4 Time of Occupancy (Dwell Time) Procedure: The dwell time was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function enabled. The spectrum analyzer is set to: Center frequency = 2441 MHz Span = zero RBW = 1 MHz VBW = 1 MHz (VBW ≥ RBW) Trace = max hold Detector function = peak Measurement Data: Channel Test Results Channel Frequency Packet Type Number (MHz) Dwell Time (ms) Result DH 1 140.05 Complies 39 2441 DH 3 265.91 Complies DH 5 311.48 Complies - See next pages for actual measured spectrum plots. Minimum Standard: 0.4 seconds within a 30 second period per any frequency Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2007, LTA Co., Ltd. Page 13 of 30

Ref. No.: LR500190707E DH 1 DH 3 DH 5 Copyright ○ c 2007, LTA Co., Ltd. Page 14 of 30

Ref. No.: LR500190707E 3.2.5 Transmitter Output Power Procedure: The peak output power was measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function disabled at the highest, middle and the lowest available channels.. After the trace being stable, Use the marker-to-peak function to set the marker to the peak of the emission. The indicated level is the peak output power. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest channels Span = 3 MHz (approximately 5 times of the 20 dB bandwidth) RBW = 1 MHz (greater than the 20dB bandwidth of the emission being measured) VBW = 1 MHz (VBW ≥ RBW) Detector function = peak Trace = max hold Sweep = auto Measurement Data: Frequency Test Results Ch. (MHz) dBm W Result 2402 0 0.04 0.001009 Complies 2441 39 0.25 0.001059 Complies 2480 78 0.98 0.001253 Complies - See next pages for actual measured spectrum plots. Minimum Standard: < 1W Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2007, LTA Co., Ltd. Page 15 of 30

Ref. No.: LR500190707E Peak Output Power Copyright ○ c 2007, LTA Co., Ltd. Page 16 of 30

Ref. No.: LR500190707E 3.2.6 Band Edge Procedure: The bandwidth at 20dB down from the highest inband spectral density is measured with a spectrum analyzer connected to the antenna terminal, while EUT had its hopping function disabled at the highest, middle and the lowest available channels. After the trace being stable, Use the marker-to-peak function to measure 20 dB down both sides of the intentional emission. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest channels RBW = 100 kHz VBW = 100 kHz Span = 10 MHz Detector function = peak Trace = max hold Sweep = auto Measurement Data: Complies - All conducted emission in any 100kHz bandwidth outside of the spread spectrum band was at least 20dB lower than the highest inband spectral density. Therefore the applying equipment meets the requirement. - See next pages for actual measured spectrum plots. Minimum Standard: > 20 dBc Measurement Setup Same as the Chapter 3.2.1 (Figure 1) Copyright ○ c 2007, LTA Co., Ltd. Page 17 of 30

Ref. No.: LR500190707E Band - edge (with Hopping) Copyright ○ c 2007, LTA Co., Ltd. Page 18 of 30

Ref. No.: LR500190707E Band - edge (without Hopping) Copyright ○ c 2007, LTA Co., Ltd. Page 19 of 30

Ref. No.: LR500190707E Band - edge (at 20 dB blow) – Low channel Frequency Range = 30 MHz ~ 10th harmonic. Copyright ○ c 2007, LTA Co., Ltd. Page 20 of 30

Ref. No.: LR500190707E Band - edge (at 20 dB blow) – Mid channel Frequency Range = 30 MHz ~ 10th harmonic. Copyright ○ c 2007, LTA Co., Ltd. Page 21 of 30

Ref. No.: LR500190707E Band - edge (at 20 dB blow) – High channel Frequency Range = 30 MHz ~ 10th harmonic. Copyright ○ c 2007, LTA Co., Ltd. Page 22 of 30

Ref. No.: LR500190707E 3.2.7 Field Strength of Harmonics Procedure: The EUT was placed on a 0.8m high wooden table inside a shielded enclosure. An antenna was placed near the EUT and measurements of frequencies and amplitudes of field strengths were recorded for reference during final measurements. For final radiated testing, measurements were performed in OATS. Measurements were performed with the EUT oriented in 3 orthogonal axis and rotated 360 degrees to determine worst-case orientation for maximum emissions. The spectrum analyzer is set to: Center frequency = the worst channel Frequency Range = 30 MHz ~ 10th harmonic. RBW = 100 kHz ( 30MHz ~ 1 GHz) Peak:VBW ≥ RBW th = 1 MHz (1 GHz ~ 10 harmonic ) Average:VBW=10Hz Span = 100 MHz Detector function = Average Trace = max hold Sweep = auto Measurement Data: Complies Low channel Mid channel High channel Frequency Level Frequency Level Frequency Level (MHz) (dBuV) (MHz) (dBuV) (MHz) (dBuV) 3204.0 36.1 3253.3 35.8 3305.3 35.7 4005.8 35.3 4065.6 36.2 4130.6 36.4 4804.3 44.7 4882.0 45.3 4960.3 45.4 - - - - - - Measurement uncertainty ± 6 dB No other emissions were detected at a level greater than 20dB below limit. Minimum Standard: FCC Part 15.209(a) Frequency (MHz) Limit (uV/m) @ 3m 30 ~ 88 100 ** 88 ~ 216 150 ** 216 ~ 960 200 ** Above 960 500 ** Except as provided in 15.209(g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88MHz, 174-216MHz or 470-806MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g. 15.231 and 15.241. Copyright ○ c 2007, LTA Co., Ltd. Page 23 of 30

243 kimg—ni, yargi—Myeon, Youngin—s, Gyeonegi—do 449—822 Korea Tel +82.31—3235008,9 Fax+82—31—3236010 RUT/Model. No.: UBHG—PHL TEST MODE: BT mode Temp Humi : 34 / §3 Tested by: KILTI.S Data: 165 o Level(dBuvim) Date: 2007—07—30 FCC CLASS—B 40 1 0 5| ; 2 3 8 30 50 100 200 500 1000 Frequency (MHz) Freq Reading C.F Result Limit Margin Height Angle Polarity 10 es.so as.70 —a9.18 35. 52 40.00 «.48 100 s40 verticai 20 as.25 a7.2o —16.38 a0.s2 40.00 9.18 ass so nortzontat a zoz.es as.s0 —13.13 30. 67 43. 5o 12.83 208 109 rortzoNtat a rev.es 45. so —5.68 as.se 46.00 10. 18 asi 200 HoRtzoNTAL s syi.es 44. 80 —s.04 as.ve 46.00 9.24 aso 119 ortzoNTAL 6. a74.e5 40. 70 ~5.98 as.77 46.00 11.23 aso 208 rortzoNTAL Remarks: C.F (Correction Factor} = Antenna factor 4 Cable loss — Preamp gain

243 kimg—ni, yargi—Myeon, Youngin—s, Gyeonegi—do 449—822 Korea Tel +82.31—3235008,9 Fax+82—31—3236010 RUT/Model. No.: UBHG—PHL TEST MODE: CHARGING + BT mode Temp Humi : 34 / §3 Tested by: KILTI.S Data: 164 o Level(dBuvim) Date: 2007—07—30 FCC CLASS—B 4 & 40 1 2 3 0 30 50 100 200 500 1000 Frequency (MHz) Freq Reading C.F Result Limit Margin Height Angle Polarity o mt abuy db dBu¥/n dBu¥/m as cn deg 10 38.s0 a7.80 —12.90 as.00 40.00 5.00 100 2o« verttcau a e7.se 48.10 —i3.61 a«.49 40.00 s.s1 100 sos verttcau a iss.ss as.20 —ro.18 as.02 «3.50 7.48 ses 100 mortzontau a rez.as so.30 —o.82 40.48 46.00 s.se 207 so« wortzontau s sse.ve so.l0 —e.380 ai.9l 46.00 a.20 380 so nortzoutan 6. sso.es a9.80 ~a.ar ail49 46.00 a.51 aso zos wortzontau Remarks: C.F (Correction Factor} = Antenna factor 4 Cable loss — Preamp gain

Ref. No.: LR500190707E 3.2.8 AC Conducted Emissions Procedure: The conducted emissions are measured in the shielded room with a spectrum analyzer in peak hold. While the measurement, EUT had its hopping function disabled at the middle channels in line with Section 15.31(m). Emissions closest to the limit are measured in the quasi-peak mode (QP) with the tuned receiver using a bandwidth of 9 kHz. The emissions are maximized further by cable manipulation and Exerciser operation. The highest emissions relative to the limit are listed. Measurement Data: Complies - See next pages for actual measured spectrum plots. - No emissions were detected at a level greater than 10dB below limit. Minimum Standard: FCC Part 15.207(a)/EN 55022 Frequency Range Conducted Limit (dBuV) (MHz) Quasi-Peak Average 0.15 ~ 0.5 66 to 56 * 56 to 46 * 0.5 ~ 5 56 46 5 ~ 30 60 50 * Decreases with the logarithm of the frequency Copyright ○ c 2007, LTA Co., Ltd. Page 26 of 30

243 kimg—ni, yargi—Myeon, Youngin—s, Gyeonegi—do 449—822 Korea Tel +82.31—323.5008 Fa+82.31—323—6010 UT / Model No. : UBHS—PRL Phase : urmE Test Mode : CHARGING + BT mode Test Power 120 / so Temp. /Huni.. : 25 / s5 Test Engineer : B.S.RIH Data: 231 File: E00e3 EMI DATAI2007.TA_Conduction_0707_2.EMI (231) go Level {dBuy) Date: 2007—07—28 CISPR CLASS—B CISPR CLASS—8 (AVG) L;Lu, *' . ; ML 8 0.15 0.5 1 2 5 10 20 30 Frequency (MHz) Freq m» RD C.Y Result Result Limit Limit Margin Margin l1.19s as.40 sa.7s o.96 ae.se as.es eo.o0 §0.00 as.s4 15.31 11.870 so.so 26.20 1.00 ar.so 27.20 e0.o0 s0.00 28.50 22.80 Remarks: C.F (Correction Factor) = Insertion loss + Cable loss

OCB LTA 243 kimg—ni, yargi—Myeon, Youngin—s, Gyeonegi—do 449—822 Korea Tel +82.31—323.5008 Fa+82.31—323—6010 RUT / Model No. : UBHS—PHL Phase : weutral Test Mode : CHARCTNG + BT mode Test Power : 220 / so Tenp . /Hun.. : 2s / 5s Test Engineer Data: 227 File: E0Oe3 EMI DATA2007.TA_Conduction_0707_2.EMI (227) o Level(dBu¥) Date: 2007—07—28 CISPRCLASS—B CISPR CLASS—8 (AVG) 40 Hargin ay 11.870 ao.so 27.4l 0.96 ar.ve as.s7 eo.o0 so.00 2s.24 2l.63 Remarks: C.F (Correction Factor) = Insertion loss + Cable loss

Ref. No.: LR500190707E APPENDIX TEST EQUIPMENT USED FOR TESTS Copyright ○ c 2007, LTA Co., Ltd. Page 29 of 30

Ref. No.: LR500190707E Description Model No. Serial No. Manufacturer Next Cal. Date 1 Spectrum Analyzer 8594E 3649A03649 HP Apr-08 2 Signal Generator 8648C 3623A02597 HP Apr-08 3 Attenuator (3dB) 8491A 37822 HP Nov-07 4 Attenuator (10dB) 8491A 63196 HP Nov-07 5 EMI Test Receiver ESVD 843748/001 R&S Jan-08 6 LISN KNW-407 8-1430-1 Kyoritsu Jan-08 7 Two-Line V-Network ESH3-Z5 893045/017 R&S Jan-08 8 RF Amplifier 8447D 2949A02670 HP Jan-08 9 RF Amplifier 8447D 2439A09058 HP Jan-08 10 RF Amplifier 8449B 3008A02126 HP Apr-09 11 Test Receiver ESHS10 828404009 R&S Jan-08 12 TRILOG Antenna VULB 9160 9160-3212 SCHWARZBECK Jul-08 13 Log.-Per. Antenna VULP 9118 9118 A 401 SCHWARZBECK Apr-09 14 Biconical Antenna BBA 9106 VHA 9103-2315 SCHWARZBECK Apr-09 15 Horn Antenna 3115 00055005 ETS LINDGREN Mar-09 16 Dipole Antenna VHA9103 2116 Schwarzbeck Nov-07 17 Dipole Antenna VHA9103 2117 Schwarzbeck Nov-07 18 Dipole Antenna UHA9105 2261 Schwarzbeck Nov-07 19 Dipole Antenna UHA9105 2262 Schwarzbeck Nov-07 20 Spectrum Analyzer 8591E 3649A05888 HP Jan-08 21 Spectrum Analyzer 8563E 3425A02505 HP Apr-08 22 Hygro-Thermograph THB-36 0041557-01 ISUZU Feb-08 23 Splitter (SMA) ZFSC-2-2500 SF617800326 Mini-Circuits Jun-08 24 RF Switch MP59B 6200414971 ANRITSU Jun-08 25 RF Switch MP59B 6200438565 ANRITSU Jun-08 26 Power Divider 11636A 6243 HP Nov-07 27 DC Power Supply 6622A 3448A03079 HP Oct-07 28 Attenuator (30dB) 11636A 6243 HP Nov-07 29 Frequency Counter 5342A 2826A12411 HP Apr-08 30 Power Meter EPM-441A GB32481702 HP Apr-08 31 Power Sensor 8481A 2702A64048 HP Apr-08 32 Audio Analyzer 8903B 3729A18901 HP Nov-07 33 Modulation Analyzer 8901B 3749A05878 HP Nov-07 34 TEMP & HUMIDITY Chamber YJ-500 L05022 JinYoung Tech Oct-07 35 LOOP-ANTENNA FMZB 1516 151602/94 SCHWARZBECK Mar-09 Copyright ○ c 2007, LTA Co., Ltd. Page 30 of 30


Document Created: 2007-08-08 19:39:38
Document Modified: 2007-08-08 19:39:38
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC