Test Report DFS

FCC ID: UDX-60082010

Test Report

Download: PDF
FCCID_4127250

FCC DFS Test Report Report No. : FZ851627 FCC DFS Test Report FCC ID : UDX-60082010 Equipment : Network Camera Brand Name : CISCO Model Name : MV32-HW Applicant/ : Cisco Systems, Inc. Manufacturer 170 West Tasman Drive San Jose, CA. 95134 USA Standard : 47 CFR FCC Part 15.407 The product was received on May 24, 2018, and testing was started from Nov. 19, 2018 and completed on Nov. 19, 2018. We, SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, would like to declare that the tested sample has been evaluated in accordance with the procedures given in KDB 905462 D02 UNII DFS Compliance Procedures New Rules v02 and shown compliance with the applicable technical standards. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any agency of United States government. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. ___________________________________________ __________________________________________ Approved by: Allen Lin SDoC by: XXXXX SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) TEL : 886-3-327-3456 Page Number : 1 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 Table of Contents HISTORY OF THIS TEST REPORT .................................................................................................................. 3 SUMMARY OF TEST RESULT ......................................................................................................................... 4 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information.............................................................................................................................................. 5 1.2 Testing Applied Standards ..................................................................................................................... 7 1.3 Testing Location Information .................................................................................................................. 7 2 TEST CONFIGURATION OF EUT......................................................................................................... 8 2.1 Test Channel Frequencies Configuration ............................................................................................... 8 2.2 The Worst Case Measurement Configuration ........................................................................................ 8 2.3 Support Equipment ................................................................................................................................. 8 3 DYNAMIC FREQUENCY SELECTION (DFS) TEST RESULT ............................................................. 9 3.1 General DFS Information ....................................................................................................................... 9 3.2 Radar Test Waveform Calibration ........................................................................................................12 3.3 In-service Monitoring ............................................................................................................................19 4 TEST EQUIPMENT AND CALIBRATION DATA ................................................................................23 5 MEASUREMENT UNCERTAINTY ......................................................................................................24 TEST SETUP PHOTOS V01 PHOTOGRAPHS OF EUT V01 TEL : 886-3-327-3456 Page Number : 2 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 History of this test report Report No. Version Description Issued Date FZ851627 01 Initial issue of report Dec. 14, 2018 TEL : 886-3-327-3456 Page Number : 3 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 Summary of Test Result Report Result Ref. Std. Clause Test Items Remark Clause (PASS/FAIL) DFS: In-Service Monitoring for Channel Move CMT ≤ 10sec 3.3 KDB 905462 7.8.3 PASS Time (CMT) DFS: In-Service Monitoring for Channel Closing CCTT ≤ 60 ms starting at 3.3 KDB 905462 7.8.3 PASS Transmission Time (CCTT) CMT 200ms DFS: In-Service Monitoring for Non-Occupancy NOP ≥ 30 min 3.3 KDB 905462 7.8.3 PASS Period (NOP) Declaration of Conformity: The test results with all measurement uncertainty excluded are presented in accordance with the regulation limits or requirements declared by manufacturers. Comments and explanations: None Reviewed by: Jackson Tsai Report Producer: Michelle Tsai TEL : 886-3-327-3456 Page Number : 4 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 1 General Description 1.1 Information 1.1.1 RF General Information Specification Items Description Product Type WLAN (1TX, 1RX) Radio Type Intentional Transceiver Power Type From PoE Modulation IEEE 802.11a: OFDM (BPSK / QPSK / 16QAM / 64QAM) IEEE 802.11n/ac: see the below table Data Rate (Mbps) IEEE 802.11a: OFDM (6/9/12/18/24/36/48/54) IEEE 802.11n/ac: see the below table Channel Bandwidth 20/40/80 MHz operating channel bandwidth Operating Mode Master Bridge Mesh Client with radar detection Client without radar detection Communication Mode IP Based (Load Based) Frame Based TPC Function With TPC Without TPC Weather Band (5600~5650MHz) With 5600~5650MHz Without 5600~5650MHz Power-on cycle NA (No Channel Availability Check Function) Software / Firmware Version 0503f Note: EUT employ a TPC mechanism and TPC have the capability to operate at least 6 dB below highest RF output power. Antenna & Bandwidth Antenna One (TX) Band width Mode 20 MHz 40 MHz 80 MHz IEEE 802.11a V X X IEEE 802.11n V V X IEEE 802.11ac V V V TEL : 886-3-327-3456 Page Number : 5 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 IEEE 11n/ac Spec. Number of Protocol Data Rate / MCS Transmit Chains (NTX) 802.11n (HT20) 1 MCS0-15 802.11n (HT40) 1 MCS0-15 802.11ac (VHT20) 1 MCS 0-8/Nss1 802.11ac (VHT40) 1 MCS 0-9/Nss1 802.11ac (VHT80) 1 MCS 0-9/Nss1 Note 1: IEEE Std. 802.11n modulation consists of HT20 and HT40 (HT: High Throughput). Then EUT support HT20 and HT40. Note 2: HT20 and HT40 use a combination of OFDM-BPSK, QPSK, 16QAM, 64QAM modulation. Note 3: IEEE Std. 802.11ac modulation consists of VHT20, VHT40, VHT80 (VHT: Very High Throughput). Then EUT support VHT20, VHT40, VHT80. Note 4: VHT20, VHT40, VHT80 use a combination of OFDM-BPSK, QPSK, 16QAM, 64QAM, 256QAM modulation. Note 5: Modulation modes consist of below configuration: 11a: IEEE 802.11a, HT20/HT40: IEEE 802.11n, VHT20/VHT40/VHT80: IEEE 802.11ac 1.1.2 Antenna Information Ant. Brand Model Name Antenna Type Connector 1 ARISTOTLE RFA-25-AP628-P1-U PIFA Antenna I-PEX 2 ARISTOTLE RFA-25-AP628-P2-U Dipole Antenna I-PEX Gain (dBi) Ant. Port 2.4G 5G BT 1 1 -2.22 -1.69 -2.22 2 2 -1.4 -1.36 - For 2.4 GHz function: For IEEE 802.11b/g/n mode (1TX/1RX) The EUT support diversity function, Ant. 1 or Ant. 2 can be used as transmitting/receiving antenna. For 5 GHz function: For IEEE 802.11a/n/ac mode (1TX/1RX) The EUT support diversity function, Ant. 1 or Ant. 2 can be used as transmitting/receiving antenna. For Bluetooth function: For Bluetooth mode (1TX/1RX) Only Ant. 1 can be used as transmitting/receiving antenna. TEL : 886-3-327-3456 Page Number : 6 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 1.1.3 DFS Band Carrier Frequencies There are three bandwidth systems. For 20MHz bandwidth systems, use Channel 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140. For 40MHz bandwidth systems, use Channel 54, 62, 102, 110, 118, 126, 134. For 80MHz bandwidth systems, use Channel 58, 106, 122. Frequency Band Channel No. Frequency Channel No. Frequency 52 5260 MHz 60 5300 MHz 5250~5350 MHz 54 5270 MHz 62 5310 MHz Band 2 56 5280 MHz 64 5320 MHz 58 5290 MHz - - 100 5500 MHz 120 5600 MHz 102 5510 MHz 122 5610 MHz 104 5520 MHz 124 5620 MHz 106 5530 MHz 126 5630 MHz 5470~5725 MHz 108 5540 MHz 128 5640 MHz Band 3 110 5550 MHz 132 5660 MHz 112 5560 MHz 134 5670 MHz 116 5580 MHz 136 5680 MHz 118 5590 MHz 140 5700 MHz 1.2 Testing Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards:  KDB 905462 D02 UNII DFS Compliance Procedures New Rules v02  KDB 905462 D03 Client Without DFS New Rules v01r02 1.3 Testing Location Information Testing Location HWA YA ADD : No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) TEL : 886-3-327-3456 FAX : 886-3-327-0973 Test site Designation No. TW1190 with FCC. JHUBEI ADD : No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. TEL : 886-3-656-9065 FAX : 886-3-656-9085 Test site Designation No. TW0006 with FCC. Test Condition Test Site No. Test Engineer Test Environment Test Date DFS Site DFS01-HY Peng 27.3°C / 63.9% 19/Nov/2018 TEL : 886-3-327-3456 Page Number : 7 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 2 Test Configuration of EUT 2.1 Test Channel Frequencies Configuration Test Channel Frequencies Configuration IEEE Std. Test Channel Freq. (MHz) 802.11ac (VHT80) 5530 MHz 2.2 The Worst Case Measurement Configuration The Worst Case Mode for Following Conformance Tests Tests Item Dynamic Frequency Selection (DFS) Test Condition Conducted measurement at transmit chains The EUT shall be configured to operate at the highest transmitter output power setting. If more than one antenna assembly is intended for this power setting, the gain of the antenna assembly with the lowest gain shall be used. Modulation Mode 802.11ac (VHT80) 2.3 Support Equipment Support Equipment No. Equipment Brand Name Model Name 1 AP (Master) EDIMAX EW-7679WAC 2 NoteBook DELL Latitude E5550 3 Adapter for NB DELL FA90PSO-00 4 NoteBook DELL Latitude E5540 5 Adapter for NB DELL FA90PSO-00 TEL : 886-3-327-3456 Page Number : 8 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3 Dynamic Frequency Selection (DFS) Test Result 3.1 General DFS Information 3.1.1 DFS Parameters Table D.1: DFS requirement values Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds Channel Move Time 10 seconds (Note 1). Channel Closing Transmission Time 200 milliseconds + an aggregate of 60 milliseconds over remaining 10 second periods. (Notes 1 and 2). U-NII Detection Bandwidth Minimum 100% of the 99% power bandwidth (Note 3). Note 1: Channel Move Time and the Channel Closing Transmission Time should be performed with Radar Type 0. The measurement timing begins at the end of the Radar Type 0 burst. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate Channel changes (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. Note 3: During the U-NII Detection Bandwidth detection test, radar type 0 is used and for each frequency step the minimum percentage of detection is 90%. Measurements are performed with no data traffic. Table D.2: Interference threshold values Maximum Transmit Power Value (see note) EIRP ≥ 200 mW -64 dBm EIRP < 200 mW and PSD < 10dBm/MHz -62 dBm EIRP < 200 mW and PSD ≥ 10dBm/MHz -64 dBm Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. Note3: EIRP is based on the highest antenna gain. For MIMO devices refer to KDB Publication 662911. TEL : 886-3-327-3456 Page Number : 9 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.1.2 Applicability of DFS Requirements Prior to Use of a Channel DFS Operational mode Requirement Client without radar Client with radar Master detection detection Yes Not required Yes Non-Occupancy Period (See the note) DFS Detection Threshold Yes Not required Yes Channel Availability Check Time Yes Not required Not required U-NII Detection Bandwidth Yes Not required Yes Note : According to KDB 905462 D03 Client Without DFS New Rules v01r02 (b) 6."An analyzer plot that contains a single 30-minute sweep on the original channel " 3.1.3 Applicability of DFS Requirements during Normal Operation DFS Operational mode Requirement Client without radar Client with radar Master detection detection DFS Detection Threshold Yes Not required Yes Channel Closing Transmission Time Yes Yes Yes Channel Move Time Yes Yes Yes U-NII Detection Bandwidth Yes Not required Yes Additional requirements for devices Master Device or Client Client Without Radar Detection with multiple bandwidth modes with Radar Detection U-NII Detection Bandwidth and All BW modes must be tested Not required Statistical Performance Check Channel Move Time and Channel Test using widest BW mode Test using the widest BW mode Closing Transmission Time available available for the link All other tests Any single BW mode Not required Note: Frequencies selected for statistical performance check (Section 7.8.4) should include several frequencies within the radar detection bandwidth and frequencies near the edge of the radar detection bandwidth. For 802.11 devices it is suggested to select frequencies in each of the bonded 20 MHz channels and the channel center frequency. TEL : 886-3-327-3456 Page Number : 10 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.1.4 Channel Loading/Data Streaming The data file (MPEG-4) has been transmitting in a streaming mode. Software to ping the client is permitted to simulate data transfer with random ping intervals. Minimum channel loading of approximately 17%. Unicast protocol has been used. TEL : 886-3-327-3456 Page Number : 11 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.2 Radar Test Waveform Calibration 3.2.1 Short Pulse Radar Test Waveforms Minimum Radar Pulse Width Percentage of Minimum PRI (µsec) Number of Pulses Type (µsec) Successful Trials Detection 0 1 1428 18 See Note 1 See Note 1 15 unique PRI in KDB 1A 1 60% 15 905462 D02 Table 5a   1   19  10 6  Roundup   15 unique  PRI within  360   PRI    1B 1 518-3066, 60% 15 Excluding 1A PRI 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 Aggregate (Radar Types 1-4) 80% 120 Note 1: Short Pulse Radar Type 0 should be used for the detection bandwidth test, channel move time, and channel closing time tests. A minimum of 30 unique waveforms are required for each of the short pulse radar types 1 through 4. If more than 30 waveforms are used for short pulse radar types 1 through 4, then each additional waveform must also be unique and not repeated from the previous waveforms. The aggregate is the average of the percentage of successful detections of short pulse radar types 1-4. 3.2.2 Long Pulse Radar Test Waveform Minimum Pulse Chirp Number of Radar Number of Percentage of Minimum Width Width PRI (µsec) Pulses Type Bursts Successful Trials (µsec) (MHz) per Burst Detection 5 50-100 5-20 1000-2000 1-3 8-20 80% 30 Each waveform is defined as follows:  The transmission period for the Long Pulse Radar test signal is 12 seconds.  There are a total of 8 to 20 Bursts in the 12 second period, with the number of Bursts being randomly chosen. This number is Burst Count.  Each Burst consists of 1 to 3 pulses, with the number of pulses being randomly chosen. Each Burst within the 12 second sequence may have a different number of pulses.  The pulse width is between 50 and 100 microseconds, with the pulse width being randomly chosen. Each pulse within a Burst will have the same pulse width. Pulses in different Bursts may have different pulse widths.  Each pulse has a linear FM chirp between 5 and 20 MHz, with the chirp width being randomly chosen. Each pulse within a transmission period will have the same chirp width. The chirp is centered on the pulse. For example, with a radar frequency of 5300 MHz and a 20 MHz chirped signal, the chirp starts at 5290 MHz and TEL : 886-3-327-3456 Page Number : 12 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 ends at 5310 MHz.  If more than one pulse is present in a Burst, the time between the pulses will be between 1000 and 2000 microseconds, with the time being randomly chosen. If three pulses are present in a Burst, the time between the first and second pulses is chosen independently of the time between the second and third pulses.  The 12 second transmission period is divided into even intervals. The number of intervals is equal to Burst Count. Each interval is of length (12,000,000 / Burst Count) microseconds. Each interval contains one Burst. The start time for the Burst, relative to the beginning of the interval, is between 1 and [(12,000,000 / Burst Count) – (Total Burst Length) + (One Random PRI Interval)] microseconds, with the start time being randomly chosen. The step interval for the start time is 1 microsecond. The start time for each Burst is chosen independently. 3.2.3 Frequency Hopping Radar Test Waveform Minimum Pulse Hopping Radar PRI Pulses Hopping Percentage of Minimum Width Sequence Type (µsec) per Hop Rate (kHz) Successful Trials (µsec) Length (ms) Detection 6 1 333 9 0.333 300 70% 30 The FCC Type 6 waveform uses a static waveform with 100 bursts in the instruments ARB. In addition, the RF list mode is operated with a list containing 100 frequencies from a randomly generated list and it had be ensured that at least one of the random frequencies falls into the UNII Detection Bandwidth of the DUT. Each burst from the waveform file initiates a trigger pulse at the beginning that switches the RF list from one item to the next one. 3.2.4 DFS Threshold Level DFS Threshold Level DFS Threshold level: -63 dBm at the antenna connector in front of the antenna The Interference Radar Detection Threshold Level is is -64 dBm + 0 [dBi] + 1 dB = -63 dBm. That had been been taken into account the output power range and antenna gain. 3.2.5 Calibration Setup Client Conducted Calibration Setup TEL : 886-3-327-3456 Page Number : 13 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.2.6 Radar Waveform calibration Plot Modulation Mode: 802.11ac (VHT80) Test Frequency: 5530 MHz Radar #0 DFS detection threshold level TEL : 886-3-327-3456 Page Number : 14 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.2.7 Test Setup A spectrum analyzer is used as a monitor to verify that the EUT has vacated the Channel within the (Channel Closing Transmission Time and Channel Move Time, and does not transmit on a Channel during the Non-Occupancy Period after the detection and Channel move. Client without Radar Detect Conducted Measurement TEL : 886-3-327-3456 Page Number : 15 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.2.8 Data traffic Plot EUT Data traffic Plot Modulation Mode: 802.11ac (VHT80) Test Frequency: 5530 MHz TEL : 886-3-327-3456 Page Number : 16 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 Master Data Traffic Plot Modulation Mode: 802.11ac (VHT80) Test Frequency: 5530 MHz TEL : 886-3-327-3456 Page Number : 17 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 Without Data Traffic Plot Modulation Mode: 802.11ac (VHT80) Test Frequency: 5530 MHz TEL : 886-3-327-3456 Page Number : 18 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

seorroncas. FCC DFS Test Report Report No. : FZ851627 3.3 In—service Monitoring 3.3.1 In—service Monitoring Limit In—service Monitoring Limit Channel Move Time 10 sec Channel Closing Transmission Time |200 ms + an aggregate of 60 ms over remaining 10 sec periods. Non—occupancy period Minimum 30 minutes 3.3.2 Measuring Instruments Refer a test equipment and calibration data table in this test report. 3.3.3 Test Procedures Test Method K verified during In—Service Monitoring; Channel Closing Transmission Time, Channel Move Time. Client Device will associate with the EUT. Observe the transmissions of the EUT at the end of the radar Burst on the Operating Channel for duration greater than 10 seconds. Measure and record the transmissions from the EUT during the observation time (Channel Move Time}. Compare the Channel Move Time and Channel Closing Transmission Time limits. K verified during In—Service Monitoring; Channel Closing Transmission Time, Channel Move Time. One 12 sec plot needs to be reported for the Short Pulse Radar Types 0. And zoom—in a 60 ms plot verified channel closing time for the aggregate transmission time starting from 200ms after the end of the radar signal to the completion of the channel move. B verified during In—Service Monitoring; Non—Occupancy Period. Client Device will associate with the EUT. Observe the transmissions of the EUT at the end of the radar Burst on the Operating Channel for duration greater than 10 seconds. Measure and record the transmissions from the EUT during the observation time (Non—Occupancy Period). Compare the Non—Occupancy Period limits. 3.3.4 Test Result of In—service Monitoring Modulation Mode: 802.11ac (VHT80) Test Result Parameter Limit Type 0 Test Channel (MHz) 5530 MHz — Channel Move Time (sec.) 0.0225 < 10s Channel Closing Transmission Time (ms) (Note) 0.000 < 60ms Non—Occupancy Period (min.) >30 > 30 min Note: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move (an aggregate of 60 milliseconds) during the remainder of the 10 seconds period. The aggregate duration of control signals will not count quiet periods in between transmissions. TEL : 886—3—327—3456 Page Number : 19 of 24 FAX : 886—3—327—0978 Issued Date : Dec. 14, 2018 Report Template No.: HE1—D2 Ver2.3 Report Version : 01 FCC ID : UDX—60082010

FCC DFS Test Report Report No. : FZ851627 3.3.5 Test Plot of In-Service Monitoring for Channel Move Time Modulation Mode Freq. Radar Type 802.11ac (VHT80) 5530 MHz 0 EUT Signal Radar TEL : 886-3-327-3456 Page Number : 20 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.3.6 Test Plot of In-Service Monitoring for Channel Closing Transmission Time Modulation Mode Freq. Radar Type 802.11ac (VHT80) 5530 MHz 0 Channel Closing Transmission Time is comprised of 200 ms starting at the beginning of the Channel Move Time plus 60ms additional intermittent control signals TEL : 886-3-327-3456 Page Number : 21 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 3.3.7 Test Plot of In-Service Monitoring for Non-Occupancy Period Modulation Mode Freq. 802.11ac (VHT80) 5530 MHz Non-Occupancy Period During the 30 minutes observation time, UUT did not make any transmissions on a channel after a radar signal was detected on that channel by either the Channel Availability Check or the In-Service Monitoring. TEL : 886-3-327-3456 Page Number : 22 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

FCC DFS Test Report Report No. : FZ851627 4 Test Equipment and Calibration Data Calibration Calibration Due Instrument Manufacturer Model No. Serial No. Spec. Date Date Spectrum R&S FSP7 100645 9kHz ~ 7GHz 27/Sep/2018 26/Sep/2019 Analyzer Vector Signal Keysight N5182B MY53051912 9kHz ~ 6GHz 04/Dec/2017 03/Dec/2018 Generator MTJ RF cable 2m 000000-MT18A-200 D5100 1 GHz ~ 40 GHz 01/Nov/2018 31/Oct/2019 Cooperation HUBER+ RF cable 0.5m SUCOFLEX 104 MY23003/4 25 MHz ~ 26.5 GHz 01/Nov/2018 31/Oct/2019 SUHNER HUBER+ RF cable 0.2m SUCOFLEX 104 SN324530/4 25 MHz ~ 26.5 GHz 01/Nov/2018 31/Oct/2019 SUHNER TEL : 886-3-327-3456 Page Number : 23 of 24 FAX : 886-3-327-0973 Issued Date : Dec. 14, 2018 Report Template No.: HE1-D2 Ver2.3 Report Version : 01 FCC ID : UDX-60082010

seorroncas. FCC DFS Test Report Report No. : FZ851627 5 Measurement Uncertainty Test Items Uncertainty Remark Conducted Emission 1.3 dB Confidence levels of 95% Temperature 0.7 °C Confidence levels of 95% Humidity 4% Confidence levels of 95% ————THE END———— TEL : 886—3—327—3456 Page Number : 24 of 24 FAX : 886—3—327—0978 Issued Date : Dec. 14, 2018 Report Template No.: HE1—D2 Ver2.3 Report Version : 01 FCC ID : UDX—60082010


Document Created: 2019-03-31 09:36:49
Document Modified: 2019-03-31 09:36:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC