Test Report DTS BT LE

FCC ID: UDX-60053010

Test Report

Download: PDF
FCCID_3501326

                                                               FCC Test Report

                       Report No.: RF170314C06

                            FCC ID: UDX-60053010

                       Test Model: Z3-HW

                 Received Date: Mar. 14, 2017

                         Test Date: Apr. 13 ~ Apr. 20, 2017

                     Issued Date: May 03, 2017


                         Applicant: Cisco Systems, Inc.

                          Address: 170 West Tasman Drive, San Jose, CA 95134



                        Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

                    Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan,
                                 R.O.C.
                  Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City
                                 33383, TAIWAN (R.O.C.)




This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted
only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this
report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product
unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you
provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided,
however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time
shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific
mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification.
This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies.

Report No.: RF170314C06                                              Page No. 1 / 34                                            Report Format Version: 6.1.1


                                                                   Table of Contents
Release Control Record .................................................................................................................................. 4
1         Certificate of Conformity...................................................................................................................... 5
2         Summary of Test Results ..................................................................................................................... 6
    2.1      Measurement Uncertainty ................................................................................................................... 6
    2.2      Modification Record ............................................................................................................................ 6
3         General Information .............................................................................................................................. 7
    3.1      General Description of EUT ................................................................................................................ 7
    3.2      Description of Test Modes ................................................................................................................... 8
    3.2.1    Test Mode Applicability and Tested Channel Detail............................................................................. 9
    3.3      Description of Support Units .............................................................................................................. 11
    3.3.1    Configuration of System under Test ................................................................................................... 11
    3.4      Duty Cycle of Test Signal .................................................................................................................. 12
    3.5      General Description of Applied Standards ........................................................................................ 12
4         Test Types and Results ...................................................................................................................... 13
    4.1      Radiated Emission and Bandedge Measurement............................................................................. 13
    4.1.1    Limits of Radiated Emission and Bandedge Measurement .............................................................. 13
    4.1.2    Test Instruments ................................................................................................................................ 14
    4.1.3    Test Procedures................................................................................................................................. 15
    4.1.4    Deviation from Test Standard ............................................................................................................ 15
    4.1.5    Test Set Up ........................................................................................................................................ 16
    4.1.6    EUT Operating Conditions................................................................................................................. 17
    4.1.7    Test Results ....................................................................................................................................... 18
    4.2      Conducted Emission Measurement .................................................................................................. 22
    4.2.1    Limits of Conducted Emission Measurement .................................................................................... 22
    4.2.2    Test Instruments ................................................................................................................................ 22
    4.2.3    Test Procedures................................................................................................................................. 22
    4.2.4    Deviation from Test Standard ............................................................................................................ 23
    4.2.5    Test Setup .......................................................................................................................................... 23
    4.2.6    EUT Operating Conditions................................................................................................................. 23
    4.2.7    Test Results ....................................................................................................................................... 24
    4.3      6dB Bandwidth Measurement ........................................................................................................... 26
    4.3.1    Limits of 6dB Bandwidth Measurement ............................................................................................. 26
    4.3.2    Test Setup .......................................................................................................................................... 26
    4.3.3    Test Instruments ................................................................................................................................ 26
    4.3.4    Test Procedure .................................................................................................................................. 26
    4.3.5    Deviation from Test Standard ............................................................................................................ 26
    4.3.6    EUT Operating Conditions................................................................................................................. 26
    4.3.7    Test Result ......................................................................................................................................... 27
    4.4      Conducted Output Power Measurement........................................................................................... 28
    4.4.1    Limits of Conducted Output Power Measurement ............................................................................ 28
    4.4.2    Test Setup .......................................................................................................................................... 28
    4.4.3    Test Instruments ................................................................................................................................ 28
    4.4.4    Test Procedures................................................................................................................................. 28
    4.4.5    Deviation from Test Standard ............................................................................................................ 28
    4.4.6    EUT Operating Conditions................................................................................................................. 28
    4.4.7    Test Results ....................................................................................................................................... 28
    4.5      Power Spectral Density Measurement .............................................................................................. 29
    4.5.1    Limits of Power Spectral Density Measurement ............................................................................... 29
    4.5.2    Test Setup .......................................................................................................................................... 29
    4.5.3    Test Instruments ................................................................................................................................ 29
    4.5.4    Test Procedure .................................................................................................................................. 29
    4.5.5    Deviation from Test Standard ............................................................................................................ 29
    4.5.6    EUT Operating Condition .................................................................................................................. 29

Report No.: RF170314C06                                              Page No. 2 / 34                                             Report Format Version: 6.1.1


    4.5.7   Test Results ....................................................................................................................................... 30
    4.6     Conducted Out of Band Emission Measurement .............................................................................. 31
    4.6.1   Limits of Conducted Out of Band Emission Measurement ............................................................... 31
    4.6.2   Test Setup .......................................................................................................................................... 31
    4.6.3   Test Instruments ................................................................................................................................ 31
    4.6.4   Test Procedure .................................................................................................................................. 31
    4.6.5   Deviation from Test Standard ............................................................................................................ 31
    4.6.6   EUT Operating Condition .................................................................................................................. 31
    4.6.7   Test Results ....................................................................................................................................... 32
5       Pictures of Test Arrangements .......................................................................................................... 33
Appendix – Information on the Testing Laboratories ................................................................................ 34




Report No.: RF170314C06                                             Page No. 3 / 34                                             Report Format Version: 6.1.1


                                          Release Control Record


Issue No.             Description                                         Date Issued
RF170314C06           Original release.                                   May 03, 2017




Report No.: RF170314C06                      Page No. 4 / 34       Report Format Version: 6.1.1


1    Certificate of Conformity


            Product: 802.11a/b/g/n/ac Wireless Security Appliance

              Brand: Cisco

        Test Model: Z3-HW

    Sample Status: Engineering sample

          Applicant: Cisco Systems, Inc.

          Test Date: Apr. 13 ~ Apr. 20, 2017

         Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247)
                          ANSI C63.10:2013




The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd.,
Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data
evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts
of the measurements of the sample’s EMC characteristics under the conditions specified in this report.




      Prepared by :                                               , Date:       May 03, 2017
                             Pettie Chen / Senior Specialist




     Approved by :                                                , Date:       May 03, 2017
                               Ken Liu / Senior Manager




Report No.: RF170314C06                         Page No. 5 / 34                      Report Format Version: 6.1.1


2      Summary of Test Results


                               47 CFR FCC Part 15, Subpart C (Section 15.247)

        FCC
                               Test Item                   Result                    Remarks
       Clause
                                                                      Meet the requirement of limit.
       15.207      AC Power Conducted Emission              Pass      Minimum passing margin is -5.45dB at
                                                                      0.38706MHz.
       15.205 /                                                       Meet the requirement of limit.
                   Radiated Emissions and Band Edge
       15.209 /                                             Pass      Minimum passing margin is -1.3dB at
                   Measurement
      15.247(d)                                                       4960.00MHz.

      15.247(d)    Antenna Port Emission                    Pass      Meet the requirement of limit.

    15.247(a)(2)   6dB bandwidth                            Pass      Meet the requirement of limit.

      15.247(b)    Conducted power                          Pass      Meet the requirement of limit.

      15.247(e)    Power Spectral Density                   Pass      Meet the requirement of limit.

       15.203      Antenna Requirement                      Pass      No antenna connector is used.


2.1      Measurement Uncertainty
Where relevant, the following measurement uncertainty levels have been estimated for tests performed on
the EUT as specified in CISPR 16-4-2:
                                                                                      Expanded Uncertainty
                    Measurement                                 Frequency
                                                                                           (k=2) (±)
         Conducted Emissions at mains ports                150kHz ~ 30MHz                   2.94 dB
                                                           30MHz ~ 200MHz                   3.59 dB
           Radiated Emissions up to 1 GHz
                                                          200MHz ~1000MHz                   3.60 dB
                                                            1GHz ~ 18GHz                    2.29 dB
           Radiated Emissions above 1 GHz
                                                            18GHz ~ 40GHz                   2.29 dB


2.2      Modification Record
There were no modifications required for compliance.




Report No.: RF170314C06                       Page No. 6 / 34                          Report Format Version: 6.1.1


3     General Information
3.1    General Description of EUT

 Product                     802.11a/b/g/n/ac Wireless Security Appliance
 Brand                       Cisco
 Test Model                  Z3-HW
 Status of EUT               Engineering sample
 Power Supply Rating         54Vdc (adapter)
 Modulation Type             GFSK
 Transfer Rate               1Mbps
 Operating Frequency         2402 ~ 2480MHz
 Number of Channel           40
 Channel Spacing             2MHz
 Output Power                3.258mW
 Antenna Type                Chip antenna with 2.66dBi gain
 Antenna Connector           NA
 Accessory Device            Adapter
 Data Cable Supplied         NA
Note:
1. The EUT consumes power from the following adapter.
 Adapter
 Brand                         Cisco
 Model                         MA-PWR-50WAC
 Input Power                   100-240VAC, 50/60Hz, 2A
 Output Power                  54V, 0.92A
                               1.5m non-shielded DC cable without core
 Power Line
                               1.7m non-shielded AC cable without core
2. WLAN 2.4GHz, 5GHz & BT LE technology can transmit at same time.
3. Spurious emission of the simultaneous operation (WLAN 2.4GHz, 5GHz & BT LE) has been evaluated and
   no non-compliance was found.
4. The above EUT information is declared by manufacturer and for more detailed features description, please
   refer to the manufacturer's specifications or user's manual.




Report No.: RF170314C06                      Page No. 7 / 34                        Report Format Version: 6.1.1


3.2   Description of Test Modes

40 channels are provided to this EUT:
  Channel      Freq. (MHz)   Channel    Freq. (MHz)      Channel   Freq. (MHz)   Channel      Freq. (MHz)
      0            2402         10         2422               20      2442         30             2462
      1            2404         11         2424               21      2444         31             2464
      2            2406         12         2426               22      2446         32             2466
      3            2408         13         2428               23      2448         33             2468
      4            2410         14         2430               24      2450         34             2470
      5            2412         15         2432               25      2452         35             2472
      6            2414         16         2434               26      2454         36             2474
      7            2416         17         2436               27      2456         37             2476
      8            2418         18         2438               28      2458         38             2478
      9            2420         19         2440               29      2460         39             2480




Report No.: RF170314C06                     Page No. 8 / 34                       Report Format Version: 6.1.1


3.2.1        Test Mode Applicability and Tested Channel Detail

    EUT                                 APPLICABLE TO
 CONFIGURE                                                                                       DESCRIPTION
   MODE               RE1G            RE<1G         PLC           APCM

         -               √               √            √               √         -

Where         RE1G: Radiated Emission above 1GHz &        RE<1G: Radiated Emission below 1GHz
                     Bandedge Measurement
              PLC: Power Line Conducted Emission           APCM: Antenna Port Conducted Measurement

Note:
1. The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Z-plane.




Radiated Emission Test (Above 1GHz):

        Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
        between available modulations, data rates and antenna ports (if EUT with antenna diversity
        architecture).
        Following channel(s) was (were) selected for the final test as listed below.
        EUT
 CONFIGURE           AVAILABLE CHANNEL             TESTED CHANNEL            MODULATION TYPE              DATA RATE (Mbps)
     MODE
         -                   0 to 39                   0, 19, 39                    GFSK                           1



Radiated Emission Test (Below 1GHz):

        Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
        between available modulations, data rates and antenna ports (if EUT with antenna diversity
        architecture).
        Following channel(s) was (were) selected for the final test as listed below.
        EUT
 CONFIGURE           AVAILABLE CHANNEL             TESTED CHANNEL            MODULATION TYPE              DATA RATE (Mbps)
     MODE
         -                   0 to 39                       0                        GFSK                           1



Power Line Conducted Emission Test:

        Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
        between available modulations, data rates and antenna ports (if EUT with antenna diversity
        architecture).
        Following channel(s) was (were) selected for the final test as listed below.
        EUT
 CONFIGURE           AVAILABLE CHANNEL             TESTED CHANNEL            MODULATION TYPE              DATA RATE (Mbps)
     MODE
         -                   0 to 39                       0                        GFSK                           1




Report No.: RF170314C06                                Page No. 9 / 34                                Report Format Version: 6.1.1


Antenna Port Conducted Measurement:

     This item includes all test value of each mode, but only includes spectrum plot of worst value of each
     mode.
     Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
     between available modulations, data rates and antenna ports (if EUT with antenna diversity
     architecture).
     Following channel(s) was (were) selected for the final test as listed below.
     EUT
 CONFIGURE        AVAILABLE CHANNEL         TESTED CHANNEL              MODULATION TYPE      DATA RATE (Mbps)
    MODE
       -                  0 to 39               0, 19, 39                     GFSK                     1




Test Condition:

 APPLICABLE TO        ENVIRONMENTAL CONDITIONS                 INPUT POWER                    TESTED BY
      RE1G                   23deg. C, 71%RH                      120Vac, 60Hz               James Yang
      RE<1G                   23deg. C, 71%RH                      120Vac, 60Hz               Jones Chang
       PLC                    25deg. C, 75%RH                      120Vac, 60Hz               James Yang
      APCM                    25deg. C, 60%RH                      120Vac, 60Hz                Ted Chang




Report No.: RF170314C06                         Page No. 10 / 34                          Report Format Version: 6.1.1


3.3      Description of Support Units

The EUT has been tested as an independent unit together with other necessary accessories or support units.
The following support units or accessories were used to form a representative test configuration during the
tests.

 ID         Product           Brand                Model No.             Serial No.             FCC ID                  Remarks
 A.        Notebook           DELL                  E5410                1HC2XM1          FCC DoC Approved -
 B.          Load              N/A                   N/A                      N/A                    N/A       -
 C.      USB 3.0 Flash         HP                   v250W                      01                    N/A       -
Note:
1. All power cords of the above support units are non-shielded (1.8m).
2. Item A acted as communication partner to transfer data.


                                                                      Shielding
 ID           Descriptions              Qty.         Length (m)                       Cores (Qty.)                 Remarks
                                                                      (Yes/No)
 1.     RJ45 Cable                       4               1.8              N                0          Cat5e
 2.     RJ45 Cable                       1                 10             N                0          Cat5e


3.3.1      Configuration of System under Test




                         Load (B)            (1)                   EUT
                                                                                               USB 3.0 Flash (C)

                                             (2)


                                                                                                           Adapter (EUT)




                                                                                                                               Remote site




                                                        Notebook (A)




Report No.: RF170314C06                                     Page No. 11 / 34                                  Report Format Version: 6.1.1


3.4   Duty Cycle of Test Signal
Duty cycle = 100%




3.5   General Description of Applied Standards
The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the
requirements of the following standards:

FCC Part 15, Subpart C (15.247)
558074 D01 DTS Meas Guidance v04
ANSI C63.10-2013

All test items have been performed and recorded as per the above standards.



NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is
      necessary for typical use. It has been verified to comply with the requirements of FCC Part 15,
      Subpart B, Class B (DoC). The test report has been issued separately.




Report No.: RF170314C06                       Page No. 12 / 34                       Report Format Version: 6.1.1


4       Test Types and Results
4.1     Radiated Emission and Bandedge Measurement
4.1.1    Limits of Radiated Emission and Bandedge Measurement

Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified
as below table. Other emissions shall be at least 20dB below the highest level of the desired power:


            Frequencies                        Field Strength                  Measurement Distance
               (MHz)                         (microvolts/meter)                      (meters)

            0.009 ~ 0.490                       2400/F(kHz)                              300
            0.490 ~ 1.705                       24000/F(kHz)                              30
            1.705 ~ 30.0                              30                                  30
               30 ~ 88                               100                                   3
              88 ~ 216                               150                                   3
              216 ~ 960                              200                                   3
             Above 960                               500                                   3
Note:
1.    The lower limit shall apply at the transition frequencies.
2.    Emission level (dBuV/m) = 20 log Emission level (uV/m).
3.    For frequencies above 1000MHz, the field strength limits are based on average detector, however, the
      peak field strength of any emission shall not exceed the maximum permitted average limits, specified
      above by more than 20dB under any condition of modulation.




Report No.: RF170314C06                       Page No. 13 / 34                        Report Format Version: 6.1.1


4.1.2   Test Instruments

       Description &
                                  Model No.                   Serial No.         Cal. Date          Cal. Due
       Manufacturer
Test Receiver
                                   N9038A                   MY55420137         Mar. 27, 2017     Mar. 26, 2018
KEYSIGHT
Spectrum Analyzer
                                    FSP40                         100041       Nov. 16, 2016 Nov. 15, 2017
ROHDE & SCHWARZ
BILOG Antenna
                                  VULB9168                    9168-171         Dec. 28, 2016 Dec. 27, 2017
SCHWARZBECK
HORN Antenna
                                    9120D                          209         Dec. 27, 2016 Dec. 26, 2017
SCHWARZBECK
HORN Antenna
                                  BBHA 9170                BBHA9170241         Dec. 14, 2016 Dec. 13, 2017
SCHWARZBECK
Loop Antenna                       EM-6879                         269         Aug. 11, 2016 Aug. 10, 2017
Preamplifier
                                    8447D                   2944A10738         Aug. 22, 2016 Aug. 21, 2017
Agilent
Preamplifier
                                    8449B                   3008A01922         Sep. 18, 2016 Sep. 17, 2017
Agilent
RF signal cable
                               SUCOFLEX 104          Cable-CH3-03 (214378) Aug. 22, 2016 Aug. 21, 2017
HUBER+SUHNER
RF signal cable                                            Cable-CH3-03
                               SUCOFLEX 106                                    Aug. 22, 2016 Aug. 21, 2017
HUBER+SUHNER                                              (309224+12738)
Software                       ADT_Radiated_
                                                                   NA               NA                 NA
BV ADT                          V7.6.15.9.4
Antenna Tower
                                   MA 4000                        013303            NA                 NA
inn-co GmbH
Antenna Tower Controller
                                    AT100                   AT93021702              NA                 NA
BV ADT
Turn Table
                                    TT100                   TT93021702              NA                 NA
BV ADT
Turn Table Controller
                                    SC100                   SC93021702              NA                 NA
BV ADT
Turn Table
                                    TT100                   TT93021705              NA                 NA
BV ADT
Turn Table Controller
                                    SC100                   SC93021705              NA                 NA
BV ADT
High Speed Peak Power
                                   ML2495A                    0824012          Aug. 11, 2016 Aug. 10, 2017
Meter
Power Sensor                       MA2411B                    0738171          Aug. 11, 2016 Aug. 10, 2017

Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable
         to NML/ROC and NIST/USA.
      2. The test was performed in HwaYa Chamber 3.
      3. The horn antenna and preamplifier (model: 8449B) are used only for the measurement of emission
         frequency above 1GHz if tested.
      4. The FCC Site Registration No. is 988962.
      5. The IC Site Registration No. is IC 7450F-3.




Report No.: RF170314C06                        Page No. 14 / 34                        Report Format Version: 6.1.1


4.1.3   Test Procedures

For Radiated emission below 30MHz
a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber
    room. The table was rotated 360 degrees to determine the position of the highest radiation.
b.   The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top
     of a variable-height antenna tower.
c.   Both X and Y axes of the antenna are set to make the measurement.
d.   For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned
     from 0 degrees to 360 degrees to find the maximum reading.
e.   The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with
     Maximum Hold Mode.
NOTE:
1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency
   below 30MHz.


For Radiated emission above 30MHz
a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above
    1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to
    determine the position of the highest radiation.
b.   The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top
     of a variable-height antenna tower.
c.   The height of antenna is varied from one meter to four meters above the ground to determine the
     maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to
     make the measurement.
d.   For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned
     to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to
     find the maximum reading.
e.   The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum
     hold mode when the test frequency is below 1 GHz.
f.   The test-receiver system was set to peak and average detect function and specified bandwidth with
     maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets
     average limit, measurement with the average detector is unnecessary.
Note:
1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for
    Quasi-peak detection (QP) at frequency below 1GHz.
2.   The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz
     for Peak detection (PK) at frequency above 1GHz.
3.   The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T
     (Duty cycle < 98%) or 3 x RBW (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz.
4.   All modes of operation were investigated and the worst-case emissions are reported.
4.1.4   Deviation from Test Standard

No deviation.




Report No.: RF170314C06                        Page No. 15 / 34                        Report Format Version: 6.1.1


4.1.5   Test Set Up

 For Radiated emission below 30MHz


                                                                    1m
            EUT&                       3m
            Support Units

                              Turn Table

              80cm


                                     Ground Plane
                                     Test Receiver




 For Radiated emission 30MHz to 1GHz

                                                       Ant. Tower
                                                                     1-4m
                                                                     Variable
              EUT&
                                           3m
                                            10m
              Support Units

                                  Turn Table

                  80cm


                                       Ground Plane

                                       Test Receiver




Report No.: RF170314C06                 Page No. 16 / 34                 Report Format Version: 6.1.1


 For Radiated emission above 1GHz



                                                                   Ant. Tower         1-4m
                                                                                      Variable
               EUT&                              3m
               Support Units

                                       Turn Table
                                                       Absorber

                 150cm


                                              Ground Plane
                                              Test Receiver




 For the actual test configuration, please refer to the attached file (Test Setup Photo).


4.1.6   EUT Operating Conditions

a. Placed the EUT on the testing table.
b. Prepared a notebook to act as a communication partner and placed it outside of testing area.
c. The communication partner connected with EUT via a RJ45 cable and ran a test program (provided by
   manufacturer) to enable EUT under transmission condition continuously at specific channel frequency.
d. The communication partner sent data to EUT by command "PING".




Report No.: RF170314C06                         Page No. 17 / 34                            Report Format Version: 6.1.1


4.1.7    Test Results
Above 1GHz Worst-Case Data
CHANNEL                    TX Channel 0            DETECTOR                 Peak (PK)
FREQUENCY RANGE            1GHz ~ 25GHz            FUNCTION                 Average (AV)


                   ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                   EMISSION                           ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT    MARGIN
NO.                  LEVEL                             HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)          (dB/m)
 1       2390.00     55.1 PK     74.0      -18.9        1.05 H     44          24.1             31.0
 2       2390.00     43.3 AV     54.0      -10.7        1.05 H     44          12.3             31.0
 3      *2402.00     95.8 PK                            1.00 H      31         64.6             31.2
 4      *2402.00     94.4 AV                            1.00 H     31          63.2             31.2
 5       4804.00     55.1 PK     74.0      -18.9        1.13 H     317         54.7              0.4
 6       4804.00     47.9 AV     54.0       -6.1        1.13 H     317         47.5              0.4
                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                   EMISSION                           ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT    MARGIN
NO.                  LEVEL                             HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)          (dB/m)
 1       2390.00     55.6 PK     74.0      -18.4        3.08 V     97          24.6             31.0
 2       2390.00     43.4 AV     54.0      -10.6        3.08 V     97          12.4             31.0
 3      *2402.00     96.0 PK                            3.16 V     102         64.8             31.2
 4      *2402.00     94.7 AV                            3.16 V     102         63.5             31.2
 5       4804.00     55.9 PK     74.0      -18.1        2.61 V     310         55.5              0.4
 6       4804.00     49.4 AV     54.0       -4.6        2.61 V     310         49.0              0.4


Remarks:
           1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
           2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
           3. The other emission levels were very low against the limit.
           4. Margin value = Emission Level – Limit value
           5. " * ": Fundamental frequency.




Report No.: RF170314C06                     Page No. 18 / 34                          Report Format Version: 6.1.1


CHANNEL                    TX Channel 19            DETECTOR                 Peak (PK)
FREQUENCY RANGE            1GHz ~ 25GHz             FUNCTION                 Average (AV)


                  ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                   EMISSION                            ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT     MARGIN
NO.                  LEVEL                              HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)     (dB)
                    (dBuV/m)                              (m)     (Degree)     (dBuV)          (dB/m)
 1     *2440.00      95.3 PK                             1.33 H      22         64.0             31.3
 2     *2440.00      94.4 AV                             1.33 H     22          63.1             31.3
 3      4880.00      55.5 PK     74.0       -18.5        1.35 H     319         54.9              0.6
 4      4880.00      49.1 AV     54.0        -4.9        1.35 H     319         48.5              0.6
                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                   EMISSION                            ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT     MARGIN
NO.                  LEVEL                              HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)     (dB)
                    (dBuV/m)                              (m)     (Degree)     (dBuV)          (dB/m)
 1     *2440.00      95.5 PK                             3.34 V     105         64.2             31.3
 2     *2440.00      94.0 AV                             3.34 V     105         62.7             31.3
 3      4880.00      58.0 PK     74.0       -16.0        2.82 V     311         57.4              0.6
 4      4880.00      51.4 AV     54.0        -2.6        2.82 V     311         50.8              0.6


Remarks:
           1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
           2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
           3. The other emission levels were very low against the limit.
           4. Margin value = Emission Level – Limit value
           5. " * ": Fundamental frequency.




Report No.: RF170314C06                      Page No. 19 / 34                          Report Format Version: 6.1.1


CHANNEL                    TX Channel 39            DETECTOR                 Peak (PK)
FREQUENCY RANGE            1GHz ~ 25GHz             FUNCTION                 Average (AV)


                  ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                   EMISSION                            ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT     MARGIN
NO.                  LEVEL                              HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)     (dB)
                    (dBuV/m)                              (m)     (Degree)     (dBuV)          (dB/m)
 1     *2480.00      92.9 PK                             1.29 H      24         61.4             31.5
 2     *2480.00      91.4 AV                             1.29 H     24          59.9             31.5
 3      2483.50      56.2 PK     74.0       -17.8        1.35 H     27          24.7             31.5
 4      2483.50      43.9 AV     54.0       -10.1        1.35 H     27          12.4             31.5
 5      4960.00      56.5 PK     74.0       -17.5        1.52 H     347         55.7              0.8
 6      4960.00      49.7 AV     54.0        -4.3        1.52 H     347         48.9              0.8
                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                   EMISSION                            ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT     MARGIN
NO.                  LEVEL                              HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)     (dB)
                    (dBuV/m)                              (m)     (Degree)     (dBuV)          (dB/m)
 1     *2480.00      92.5 PK                             3.28 V     76          61.0             31.5
 2     *2480.00      91.2 AV                             3.28 V     76          59.7             31.5
 3      2483.50      55.6 PK     74.0       -18.4        3.30 V     79          24.1             31.5
 4      2483.50      44.1 AV     54.0        -9.9        3.30 V      79         12.6             31.5
 5      4960.00      60.3 PK     74.0       -13.7        2.44 V     274         59.5              0.8
 6      4960.00      52.7 AV     54.0        -1.3        2.44 V     274         51.9              0.8


Remarks:
           1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
           2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
           3. The other emission levels were very low against the limit.
           4. Margin value = Emission Level – Limit value
           5. " * ": Fundamental frequency.




Report No.: RF170314C06                      Page No. 20 / 34                          Report Format Version: 6.1.1


Below 1GHz worst-case data
CHANNEL                   TX Channel 0             DETECTOR
                                                                            Quasi-Peak (QP)
FREQUENCY RANGE           30MHz ~ 1GHz             FUNCTION


                  ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                   EMISSION                           ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT    MARGIN
NO.                  LEVEL                             HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)          (dB/m)
 1       57.12      27.5 QP      40.0      -12.5        1.99 H     16          42.1            -14.6
 2      146.56      35.4 QP      43.5       -8.1        1.99 H     252         49.4            -14.0
 3      191.28      33.3 QP      43.5      -10.2        1.00 H     239         49.4            -16.1
 4      230.16      28.4 QP      46.0      -17.6        1.50 H     245         44.2            -15.8
 5      601.52      28.3 QP      46.0      -17.7        1.50 H     223         33.6             -5.3
 6      834.84      29.5 QP      46.0      -16.5        1.00 H     208         30.4             -0.9
                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                   EMISSION                           ANTENNA     TABLE        RAW         CORRECTION
        FREQ.                    LIMIT    MARGIN
NO.                  LEVEL                             HEIGHT     ANGLE       VALUE          FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)          (dB/m)
 1      121.28      33.7 QP      43.5       -9.8        1.00 V     186         49.8            -16.1
 2      212.66      29.2 QP      43.5      -14.3        1.00 V     245         45.1            -15.9
 3      309.88      21.4 QP      46.0      -24.6        1.00 V     233         33.2            -11.8
 4      399.31      21.3 QP      46.0      -24.7        1.49 V     279         31.5            -10.2
 5      578.19      29.9 QP      46.0      -16.1        1.00 V      91         36.0             -6.1
 6      871.78      28.9 QP      46.0      -17.1        1.00 V     189         29.4             -0.5


Remarks:
    1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
    2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
                                 – Pre-Amplifier Factor(dB)
    3. The other emission levels were very low against the limit of frequency range 30MHz ~ 1000MHz.
    4. Margin value = Emission Level – Limit value
    5. The emission levels were very low against the limit of frequency range 9kHz ~ 30MHz.




Report No.: RF170314C06                     Page No. 21 / 34                          Report Format Version: 6.1.1


4.2     Conducted Emission Measurement
4.2.1    Limits of Conducted Emission Measurement

                                                            Conducted Limit (dBuV)
        Frequency (MHz)
                                               Quasi-peak                               Average
          0.15 - 0.5                             66 - 56                                 56 - 46
          0.50 - 5.0                                 56                                    46
          5.0 - 30.0                                 60                                    50
Note: 1. The lower limit shall apply at the transition frequencies.
      2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz.


4.2.2    Test Instruments

        Description &                                                                            Due Date Of
                                 Model No.            Serial No.     Date Of Calibration
        Manufacturer                                                                              Calibration
Test Receiver
                                   ESCI                 100613          Nov. 21, 2016           Nov. 20, 2017
ROHDE & SCHWARZ
RF signal cable (with
10dB PAD)                         5D-FB            Cable-cond1-01       Dec. 22, 2016           Dec. 21, 2017
Woken
LISN
ROHDE & SCHWARZ                  ESH3-Z5             835239/001         Mar. 10, 2017           Mar. 09, 2018
(EUT)
LISN
ROHDE & SCHWARZ                  ESH3-Z5                100311           Jul. 28, 2016          Jul. 27, 2017
(Peripheral)
Software                      BV ADT_Cond_
                                                          NA                  NA                      NA
ADT                              V7.3.7.3

Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable
         to NML/ROC and NIST/USA.
      2. The test was performed in HwaYa Shielded Room 1.
      3. The VCCI Site Registration No. is C-2040.



4.2.3    Test Procedures

a.    The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being
      connected to the power mains through a line impedance stabilization network (LISN). Other support units
      were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of
      coupling impedance for the measuring instrument.
b.    Both lines of the power mains connected to the EUT were checked for maximum conducted interference.
c.    The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not
      recorded.
Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP)
       and average detection (AV) at frequency 0.15MHz-30MHz.




Report No.: RF170314C06                        Page No. 22 / 34                          Report Format Version: 6.1.1


4.2.4   Deviation from Test Standard

No deviation.



4.2.5   Test Setup

                                   Vertical Ground
                                   Reference Plane                               Test Receiver


                                   EUT
                      40cm




                                                        80cm
                      LISN



                                                                   Horizontal Ground
                                                                    Reference Plane

                          Note: 1.Support units were connected to second LISN.




For the actual test configuration, please refer to the attached file (Test Setup Photo).


4.2.6   EUT Operating Conditions

Same as 4.1.6.




Report No.: RF170314C06                         Page No. 23 / 34                           Report Format Version: 6.1.1


4.2.7   Test Results

                                                                                    Quasi-Peak (QP) /
Phase                          Line (L)                     Detector Function
                                                                                    Average (AV)
Channel                        Channel 0


                           Corr.    Reading Value     Emission Level            Limit              Margin
           Freq.
 No                       Factor       [dB (uV)]         [dB (uV)]           [dB (uV)]               (dB)
           [MHz]           (dB)      Q.P.     AV.      Q.P.     AV.        Q.P.       AV.      Q.P.        AV.
  1       0.18075         10.36     31.23    20.84    41.59    31.20      64.45     54.45     -22.86 -23.25
  2       0.36505         10.39     32.53    31.06    42.92    41.45      58.61     48.61     -15.69      -7.16
  3       0.38706         10.40     39.62    32.22    50.02    42.62      58.13     48.13      -8.11      -5.51
  4       0.44507         10.40     27.10    19.46    37.50    29.86      56.97     46.97     -19.47 -17.11
  5       0.81802         10.40     22.70    15.13    33.10    25.53      56.00     46.00     -22.90 -20.47
  6       5.86642         10.65     20.37    14.56    31.02    25.21      60.00     50.00     -28.98 -24.79

REMARKS:
               1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
               2. The emission levels of other frequencies were very low against the limit.
               3. Margin value = Emission level - Limit value
               4. Correction factor = Insertion loss + Cable loss
               5. Emission Level = Correction Factor + Reading Value.




Report No.: RF170314C06                        Page No. 24 / 34                         Report Format Version: 6.1.1


                                                                                    Quasi-Peak (QP) /
Phase                          Neutral (N)                  Detector Function
                                                                                    Average (AV)
Channel                        Channel 0


                           Corr.   Reading Value      Emission Level            Limit              Margin
           Freq.
 No                       Factor      [dB (uV)]          [dB (uV)]           [dB (uV)]               (dB)
           [MHz]           (dB)     Q.P.     AV.       Q.P.     AV.        Q.P.       AV.       Q.P.       AV.
  1       0.31813         10.15    26.83    21.07     36.98    31.22      59.76     49.76     -22.78 -18.54
  2       0.38706         10.16    40.00    32.52     50.16    42.68      58.13     48.13      -7.97      -5.45
  3       0.65216         10.16    22.78    15.48     32.94    25.64      56.00     46.00     -23.06 -20.36
  4       0.82234         10.17    23.23    16.15     33.40    26.32      56.00     46.00     -22.60 -19.68
  5       4.05986         10.34    24.25    17.11     34.59    27.45      56.00     46.00     -21.41 -18.55
  6       5.86642         10.41    21.58    15.56     31.99    25.97      60.00     50.00     -28.01 -24.03

REMARKS:
               1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
               2. The emission levels of other frequencies were very low against the limit.
               3. Margin value = Emission level - Limit value
               4. Correction factor = Insertion loss + Cable loss
               5. Emission Level = Correction Factor + Reading Value.




Report No.: RF170314C06                        Page No. 25 / 34                         Report Format Version: 6.1.1


4.3     6dB Bandwidth Measurement
4.3.1    Limits of 6dB Bandwidth Measurement

The minimum of 6dB Bandwidth Measurement is 0.5 MHz.

4.3.2    Test Setup


                                                           Spectrum
           EUT
                                    Attenuator             Analyzer


4.3.3    Test Instruments

Refer to section 4.1.2 to get information of above instrument.

4.3.4    Test Procedure

a.    Set resolution bandwidth (RBW) = 100kHz
b.    Set the video bandwidth (VBW) ≥ 3 x RBW, Detector = Peak.
c.    Trace mode = max hold.
d.    Sweep = auto couple.
e.    Measure the maximum width of the emission that is constrained by the frequencies associated with the
      two amplitude points (upper and lower) that are attenuated by 6 dB relative to the maximum level
      measured in the fundamental emission


4.3.5    Deviation from Test Standard

No deviation.


4.3.6    EUT Operating Conditions

The software provided by client to enable the EUT under transmission condition continuously at lowest,
middle and highest channel frequencies individually.




Report No.: RF170314C06                          Page No. 26 / 34                    Report Format Version: 6.1.1


4.3.7    Test Result

                                             6dB Bandwidth        Minimum Limit
        Channel           Frequency (MHz)                                                 Pass / Fail
                                                 (MHz)                (MHz)
          0                    2402                 0.71               0.5                   Pass

          19                   2440                 0.71               0.5                   Pass

          39                   2480                 0.72               0.5                   Pass

                                       Spectrum Plot of Worst Value




Report No.: RF170314C06                      Page No. 27 / 34                     Report Format Version: 6.1.1


4.4     Conducted Output Power Measurement
4.4.1        Limits of Conducted Output Power Measurement

For systems using digital modulation in the 2400–2483.5 MHz bands: 1 Watt (30dBm)

4.4.2        Test Setup



             EUT                            Power Sensor                  Power Meter
                            Attenuator




4.4.3        Test Instruments

Refer to section 4.1.2 to get information of above instrument.

4.4.4        Test Procedures

A peak power sensor was used on the output port of the EUT. A power meter was used to read the response
of the peak power sensor. Record the power level.


4.4.5        Deviation from Test Standard

No deviation.


4.4.6        EUT Operating Conditions

Same as Item 4.3.6.


4.4.7        Test Results

  Channel          Frequency (MHz) Peak Power (mW) Peak Power (dBm)             Limit (dBm)          Pass/Fail

        0                 2402              3.258                  5.13             30                 Pass

        19                2440              3.034                  4.82             30                 Pass

        39                2480              2.377                  3.76             30                 Pass




Report No.: RF170314C06                         Page No. 28 / 34                        Report Format Version: 6.1.1


4.5     Power Spectral Density Measurement
4.5.1    Limits of Power Spectral Density Measurement

The Maximum of Power Spectral Density Measurement is 8dBm.

4.5.2    Test Setup


                                                              Spectrum
               EUT
                                        Attenuator            Analyzer


4.5.3    Test Instruments

Refer to section 4.1.2 to get information of above instrument.


4.5.4    Test Procedure

a.    Set analyzer center frequency to DTS channel center frequency.
b.    Set the span to 1.5 times the DTS bandwidth.
c.    Set the RBW to: 3 kHz ≤ RBW ≤ 100 kHz.
d.    Set the VBW ≥ 3 × RBW.
e.    Detector = peak.
f.    Sweep time = auto couple.
g.    Trace mode = max hold.
h.    Allow trace to fully stabilize.
i.    Use the peak marker function to determine the maximum amplitude level within the RBW.


4.5.5    Deviation from Test Standard

No deviation.


4.5.6    EUT Operating Condition

Same as Item 4.3.6




Report No.: RF170314C06                          Page No. 29 / 34                  Report Format Version: 6.1.1


4.5.7     Test Results

                           Freq.              PSD                  Limit            Pass
        Channel
                          (MHz)              (dBm)                (dBm)             /Fail
          0               2402               -6.54                  8               Pass

          19              2440               -6.54                  8               Pass

          39              2480               -6.25                  8               Pass

                                   Spectrum Plot of Worst Value




Report No.: RF170314C06                  Page No. 30 / 34                  Report Format Version: 6.1.1


4.6     Conducted Out of Band Emission Measurement
4.6.1    Limits of Conducted Out of Band Emission Measurement

Below 20dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth).

4.6.2    Test Setup


                                                                  Spectrum
                EUT
                                         Attenuator               Analyzer


4.6.3    Test Instruments

Refer to section 4.1.2 to get information of above instrument.


4.6.4    Test Procedure

MEASUREMENT PROCEDURE REF
a.    Set the RBW = 100 kHz.
b.    Set the VBW ≥ 300 kHz.
c.    Detector = peak.
d.    Sweep time = auto couple.
e.    Trace mode = max hold.
f.    Allow trace to fully stabilize.
g.    Use the peak marker function to determine the maximum power level in any 100 kHz band segment
      within the fundamental EBW.

MEASUREMENT PROCEDURE OOBE
a.    Set RBW = 100 kHz.
b.    Set VBW ≥ 300 kHz.
c.    Detector = peak.
d.    Sweep = auto couple.
e.    Trace Mode = max hold.
f.    Allow trace to fully stabilize.
g.    Use the peak marker function to determine the maximum amplitude level.


4.6.5    Deviation from Test Standard

No deviation.

4.6.6    EUT Operating Condition

Same as Item 4.3.6




Report No.: RF170314C06                        Page No. 31 / 34                    Report Format Version: 6.1.1


4.6.7   Test Results

                                           CH 0




                                          CH 19




                                          CH 39




                    CH 0 Band edge                      CH 39 Band edge




Report No.: RF170314C06              Page No. 32 / 34             Report Format Version: 6.1.1


5     Pictures of Test Arrangements

Please refer to the attached file (Test Setup Photo).




Report No.: RF170314C06                        Page No. 33 / 34   Report Format Version: 6.1.1


Appendix – Information on the Testing Laboratories

We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to
provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and
approved according to ISO/IEC 17025.

If you have any comments, please feel free to contact us at the following:

Linko EMC/RF Lab                                      Hsin Chu EMC/RF/Telecom Lab
Tel: 886-2-26052180                                   Tel: 886-3-6668565
Fax: 886-2-26051924                                   Fax: 886-3-6668323

Hwa Ya EMC/RF/Safety Lab
Tel: 886-3-3183232
Fax: 886-3-3270892

Email: service.adt@tw.bureauveritas.com
Web Site: www.bureauveritas-adt.com

The address and road map of all our labs can be found in our web site also.



--- END ---




Report No.: RF170314C06                       Page No. 34 / 34                      Report Format Version: 6.1.1



Document Created: 2017-05-13 11:07:57
Document Modified: 2017-05-13 11:07:57

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC