DFS Test Report Part 3

FCC ID: UCE312057A

Test Report

Download: PDF
FCCID_1857317

TEST REPORT SERIAL NO: UL-RPT-RP90385JD16B VERSION 1.0 ISSUE DATE: 30 November 2012 Appendix 3. Radar Calibration Radar calibration procedure. The system was configured as shown in section 4.2, but with the spectrum analyser port terminated into a 50Ω load, and a spectrum analyser connected to the master port. The radar was then replayed by the Aeroflex DFS test system, the waveform captured, and the amplitude adjusted until correct. The accuracy of the radars pulses themselves and the software which creates them has already been approved by the FCC and NTIA. See Appendix 4 for details. Below are plots of the radar bursts at the DFS master port of the attenuation network. The Aeroflex signal generator was set to -7.7 dBm output. RBW 1 MHz Marker 1 [T1 ] * VBW 3 MHz -60.95 dBm Ref -10 dBm * Att 20 dB SWT 30 ms -2.000000 µs -10 Delta 1 [T1 ] -2.07 dB 24.276000 ms A -20 1 PK * CLRWR TRG -30 -40 LNA -50 1 -60 1 3DB TRG -67.4 dBm -70 DC -80 -90 -100 -110 Center 5.32 GHz 3 ms/ Date: 29.NOV.2012 11:26:59 Type 1 (Short) Radar Page 22 of 25 RFI Global Services Ltd trading as UL

TEST REPORT SERIAL NO: UL-RPT-RP90385JD16B VERSION 1.0 ISSUE DATE: 30 November 2012 Radar calibration procedure (continued) RBW 1 MHz Marker 1 [T1 ] * VBW 3 MHz -61.03 dBm Ref -10 dBm * Att 20 dB SWT 14 s 66.666667 µs -10 Delta 1 [T1 ] 0.64 dB 11.163600 s A -20 1 PK * CLRWR TRG -30 -40 LNA -50 1 1 -60 3DB TRG -67.4 dBm -70 DC -80 -90 -100 -110 Center 5.32 GHz 1.4 s/ Date: 29.NOV.2012 11:41:52 Type 5 (Long) Radar RFI Global Services Ltd trading as UL Page 23 of 25

TEST REPORT SERIAL NO: UL-RPT-RP90385JD16B VERSION 1.0 ISSUE DATE: 30 November 2012 Appendix 4. Aeroflex Test Platform Approval email From: Andrew Leimer [mailto:Andrew.Leimer@fcc.gov] Sent: Friday, September 23, 2011 4:24 PM To: Chisham, Steve Cc: Carey, Tim; Hack, Barry; Rashmi Doshi; Joe Dichoso Subject: RE: Certification for Aeroflex DFS solution Hello Steve, The Aeroflex "DXI based DFS test solution" system used for DFS alternative radar signal generation has been approved by the FCC and NTIA. This approval permits the system to be used by labs in the testing of DFS devices for equipment authorization Certification. It is recommended that applicants that use your system for testing include a statement in the Test Report or a Letter Exhibit stating that the system has FCC and NTIA approval. This E-mail is your record of this approval. Note that the appropriate term for your system is Approved as the term Certification is reserved for devices gaining equipment authorization through the FCC or a TCB. Regards, Andy Leimer FCC/OET/EACB Page 24 of 25 RFI Global Services Ltd trading as UL

TEST REPORT SERIAL NO: UL-RPT-RP90385JD16B VERSION 1.0 ISSUE DATE: 30 November 2012 Appendix 5. System Noise Floor Reference Plots As required by Section 8.3.18(iii) of FCC 06-96, the following plot shows the reference noise floor of the system used during measurement. RBW 1 MHz Marker 1 [T1 ] * VBW3 MHz -77.64 dBm Ref -10 dBm * Att 20 dB SWT 14 s 66.666667 µs -10 Delta 1 [T1 ] 0.35 dB 11.163600 s A -20 SGL 1 PK * CLRWR -30 -40 LNA -50 -60 3DB -70 DC 1 1 -80 -90 -100 -110 Center 5.32 GHz 1.4 s/ Date: 29.NOV.2012 11:45:57 Noise Floor of Spectrum Analyser RFI Global Services Ltd trading as UL Page 25 of 25


Document Created: 2012-12-11 09:18:31
Document Modified: 2012-12-11 09:18:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC