Installation guide

FCC ID: U5Z-RB-TX10

Users Manual

Download: PDF
FCCID_3410292

INSTALLATION INSTRUCTIONS RBAND MONITORED EDGE TRANSMITTER Model: RB-TX10 IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION The Miller Edge RBand Monitored Transmitter is intended to provide a wireless connection between a monitored sensing edge and a motorized operator. RBand Transmitters and Receivers meets the 2016 UL 325 requirements for monitored devices and have been certified as UL 325 Recognized Components. RBand is designed for use with operators that comply with 2016 UL 325 using a Miller Edge 10K Sensing Edge. 1. PARTS LIST Kit Contents: Required: 1. RBand Edge Transmitter (RB-TX10) • Miller Edge RBand 10K Edge Receiver 2. (2) 3.6V AA lithium batteries* (Door: RB-D-RX10 or Gate: RB-G-RX10) 3. (4) #6 pan head transmitter mounting screws • 1/8” flat blade screwdriver • 1/4” flat blade screwdriver *Replacement 3.6V AA lithium batteries can be • Miller Edge 10K (T2/blue band) Sensing Edge purchased at your local electronics store or via Miller Edge. Recommended: • Multi-meter capable of reading 10KΩ 2. TRANSMITTER: PROGRAM MODE 2-1. Confirm the Receiver is powered up. Prior to mounting the Transmitter, remove the cover and insert the batteries, noting their polarity. The green LED should blink to indicate that the Transmitter has not been associated with the Receiver yet [IMAGE 1]. 2-2. To enter learn mode, press and hold the Receiver program button for ~2 seconds until the R1 LED turn on, then release the button. 2-3. Press the Transmitter program button for ~2 seconds. The Receiver should beep. Wait 10 seconds for an additional beep to indicate that programming is complete. Note: Refer to Miller Edge RBand Receiver installation instructions for options for additional Transmitters. PROGRAM BUTTON (2) 3.6V AA LITHIUM BATTERIES REMOVABLE SENSING EDGE GREEN LED TERMINAL BLOCK ALIGNMENT PIN (4) CORNER ALIGNMENT PIN MOUNTING HOLES STRAIN RELIEF FITTING IMAGE 1. RBand Transmitter RB-TX10_Install_A4_20170531 Miller Edge, Inc. • www.milleredge.com • info@milleredge.com • East Coast: 800-220-4422 • West Coast: 800-887-3343

IMAGE 2. RBand Transmitter with Door Edge IMAGE 3. RBand Transmitter with Gate Edge 3. TRANSMITTER: INSTALL & TEST 3-1. Strip back approximately 2 inches of outer covering of sensing edge cable, then feed through Transmitter strain relief fitting [IMAGE 1]. Connect the two sensing edge wires to the removable terminal. Dress the wires with a small service loop and tighten the strain relief. Mount unit utilizing the mounting holes at the 4 corners of the Transmitter box. Affix lid to Transmitter, noting alignment pin [IMAGE 1]. 3-2. Test the sensing edge for functionality. 4. TRANSMITTER: SPECIFICATIONS & CONTROLS Transmitter Frequency: 916 MHz, FSK modulation TX Indicator Lights: • Green LED: Normally off • Press PROG button for status Mounting: 4 corner screws (provided) Power Source: Batteries: 2 AA, 3.6V lithium, 2 year life expectancy Dimensions: 1.80”L x 4.78”W x 1.75”H Program Button: Momentary push button is used to associate the Transmitter to the Receiver. 5. FCC COMPLIANCE Model: RB-TX10 FCC ID: U5Z-RB-TX10 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with FCC radiation exposure limits for an uncontrolled environment. This device shall be installed and operated with a minimum distance of 0.4” between users or bystanders and the device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules: These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Re-orient or relocate the receiver antenna 2. Increase the separation between the equipment and the receiver 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4. Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Miller Edge, Inc. • www.milleredge.com • info@milleredge.com • East Coast: 800-220-4422 • West Coast: 800-887-3343


Document Created: 2017-05-31 10:52:53
Document Modified: 2017-05-31 10:52:53
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC