Test Report

FCC ID: U5O-SPR009

Test Report

Download: PDF

FCCID_4037977

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

FCC TEST REPORT

For

NUMAXES

CANICOM SPRAY TRANSMITTER

Test Model: PFDRESPR009

Additional Model: PFDRESPR004

Prepared for : NUMAXES
Z.A.C. des Aulnaies - 745 rue de la Bergeresse- C.S. 30157 - 45161
Address :
OLIVET CEDEX - FRANCE

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd.
1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an
Address :
District, Shenzhen, Guangdong, China
Tel : (+86)755-82591330
Fax : (+86)755-82591332
Web : www.LCS-cert.com
Mail : webmaster@LCS-cert.com

Date of receipt of test sample : July 20, 2018
Number of tested samples : 1
Serial number : Prototype
Date of Test : July 20, 2018~ July 31, 2018
Date of Report : August 03, 2018

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

FCC -- TEST REPORT

August 03, 2018
Test Report No. : LCS180718013AEA
Date of issue

Test Model.............................. : PFDRESPR009

EUT......................................... : CANICOM SPRAY TRANSMITTER

Applicant............................... : NUMAXES
Z.A.C. des Aulnaies - 745 rue de la Bergeresse- C.S. 30157 -
Address.................................. :
45161 OLIVET CEDEX - FRANCE
Telephone............................... : /
Fax.......................................... : /

Manufacturer........................ : NUMAXES
Z.A.C. des Aulnaies - 745 rue de la Bergeresse- C.S. 30157 -
Address................................... :
45161 OLIVET CEDEX - FRANCE
Telephone............................... : /
Fax.......................................... : /

Factory................................... : /
Address................................... : /
Telephone............................... : /
Fax.......................................... : /

Test Result Positive

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

Revision History

Revision Issue Date Revisions Revised By
000 August 03, 2018 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

TABLE OF CONTENTS

1. GENERAL INFORMATION .................................................................................................................................... 6
1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................ 6
1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS .......................................................................................... 6
1.3. EXTERNAL I/O CABLE ......................................................................................................................................... 6
1.4. DESCRIPTION OF TEST FACILITY ........................................................................................................................ 6
1.5. STATEMENT OF THE MEASUREMENT UNCERTAINTY .......................................................................................... 6
1.6. MEASUREMENT UNCERTAINTY ........................................................................................................................... 7
1.7. DESCRIPTION OF TEST MODES .......................................................................................................................... 7
2. TEST METHODOLOGY ......................................................................................................................................... 8
2.1. EUT CONFIGURATION ........................................................................................................................................ 8
2.2. EUT EXERCISE ................................................................................................................................................... 8
2.3. GENERAL TEST PROCEDURES ........................................................................................................................... 8
3. SYSTEM TEST CONFIGURATION ...................................................................................................................... 9
3.1. JUSTIFICATION .................................................................................................................................................... 9
3.2. EUT EXERCISE SOFTWARE ................................................................................................................................ 9
3.3. SPECIAL ACCESSORIES ...................................................................................................................................... 9
3.4. BLOCK DIAGRAM/SCHEMATICS........................................................................................................................... 9
3.5. EQUIPMENT MODIFICATIONS .............................................................................................................................. 9
3.6. TEST SETUP ........................................................................................................................................................ 9
4. SUMMARY OF TEST RESULTS ........................................................................................................................ 10
5. TEST RESULT ....................................................................................................................................................... 11
5.1. RADIATED EMISSION MEASUREMENT............................................................................................................... 11
5.2. 20 DB BANDWIDTH MEASUREMENT ....................................................................................................... 23
5.3. AC POWER LINE CONDUCTED EMISSIONS ........................................................................................................ 25
5.4. ANTENNA REQUIREMENTS ................................................................................................................................ 26
6. LIST OF MEASURING EQUIPMENTS .............................................................................................................. 27
7. TEST SETUP PHOTOGRAPHS OF EUT .......................................................................................................... 28
8. EXTERIOR PHOTOGRAPHS OF THE EUT ..................................................................................................... 28
9. INTERIOR PHOTOGRAPHS OF THE EUT ...................................................................................................... 28

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

1.6. Measurement Uncertainty

Test Item Frequency Range Uncertainty Note
9KHz~30MHz ±3.10dB (1)
30MHz~200MHz ±2.96dB (1)
Radiation Uncertainty : 200MHz~1000MHz ±3.10dB (1)
1GHz~26.5GHz ±3.80dB (1)
26.5GHz~40GHz ±3.90dB (1)
Conduction Uncertainty : 150kHz~30MHz ±1.63dB (1)
Power disturbance : 30MHz~300MHz ±1.60dB (1)

(1). This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence
level using a coverage factor of k=2.

1.7. Description of Test Modes

The EUT has been tested under operating condition.
This test was performed with EUT in X, Y, Z position and the worst case was found when EUT in X
position.
Worst-case mode and channel used for 9 KHz-1000 MHz radiated emissions was the mode and channel
with the highest output power, that was determined to be TX mode.
***Note: Using a temporary antenna connector for the EUT when conducted measurements are
performed.

Channel List & Frequency
Channel Frequency(MHz) Channel Frequency(MHz)
1 915.011 -- --

Transmitting Frequency
Mode of Operations (MHz)
ASK 915.011
For Conducted Emission
Test Mode TX Mode
For Radiated Emission
Test Mode TX Mode

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

2. TEST METHODOLOGY

All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices.
The radiated testing was performed at an antenna-to-EUT distance of 3 meters. All radiated and
conducted emissions measurement was performed at Shenzhen LCS Compliance Testing Laboratory Ltd.

2.1. EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions
requirement and operating in a manner that intends to maximize its emission characteristics in a
continuous normal application.

2.2. EUT Exercise
The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the
measurements.
According to its specifications, the EUT must comply with the requirements of the Section 15.203, 15.205,
15.207, 15.209 and 15.249 under the FCC Rules Part 15 Subpart C.

2.3. General Test Procedures

2.3.1 Conducted Emissions

The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in
Section 6.2.1 of ANSI C63.10-2013 Conducted emissions from the EUT measured in the frequency range
between 0.15 MHz and 30MHz using Quasi-peak and average detector modes.

2.3.2 Radiated Emissions

The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360
degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving
antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be
maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find
out the maximum emissions, expiatory radiated emission measurements were made according to the
requirements in Section 6.3 of ANSI C63.10-2013.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

3. SYSTEM TEST CONFIGURATION

3.1. Justification
The system was configured for testing in a continuous transmits condition.

3.2. EUT Exercise Software
The system was configured for testing in a continuous transmits condition by software (YL_800T.exe)
provided by application.

3.3. Special Accessories
N/A

3.4. Block Diagram/Schematics
Please refer to the related document.

3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.

3.6. Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

4. SUMMARY OF TEST RESULTS

Applied Standard: FCC Part 15 Subpart C
FCC Rules Description of Test Result
§15.205(a), §15.209(a), §15.249(a),
Radiated Emissions Measurement Compliant
§15.249(c)
§15.205, §15.249(d) Emissions at Restricted Band Compliant
§15.215 99% and 20dB Bandwidth Compliant
§15.207(a) AC Line Conducted Emissions N/A*
§15.203 Antenna Requirements Compliant

Remark:

N/A* - Not Applicable!!!

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

5. TEST RESULT

5.1. Radiated Emission Measurement

5.1.1. Standard Applicable

1). According to §15.249 (d): Emissions radiated outside of the specified frequency bands, except for
harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general
radiated emission limits in §15.209, whichever is the lesser attenuation.

Frequencies (MHz) Field Strength (microvolts/meter) Measurement Distance (meters)
0.009~0.490 2400/F(KHz) 300
0.490~1.705 24000/F(KHz) 30
1.705~30.0 30 30
30~88 100 3
88~216 150 3
216~960 200 3
Above 960 500 3
2). According to §15.249 (a): Except as provided in paragraph (b) of this section, the field strength of
emissions from intentional radiators operated within these frequency bands shall comply with the
following:

Fundamental Field strength of fundamental Field strength of harmonics
frequency millivolts/meter dBuV/m microvolts/meter dBuV/m
902-928 MHz 50 94 500 54
2400-2483.5 MHz 50 94 500 54
5725-5875 MHz 50 94 500 54
24.0-24.25 GHz 250 108 2500 68
As shown in §15.35(b), for frequencies above 1000 MHz, the field strength limits in paragraphs (a) and (b)
of this section are based on average limits. However, the peak field strength of any emission shall not
exceed the maximum permitted average limits specified above by more than 20 dB under any condition of
modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall
not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth
5.1.2. Measuring Instruments and Setting

Please refer to equipment’s list in this report. The following table is the setting of spectrum analyzer and
receiver.

Spectrum Parameter Setting
Attenuation Auto
Start Frequency 1000 MHz
Stop Frequency 10th carrier harmonic
RB / VB (Emission in restricted band) 1MHz / 3MHz for Peak, 1 MHz / 10Hz for Average
RB / VB (Emission in non-restricted band) 1MHz / 3MHz for Peak, 1 MHz / 10Hz for Average

Receiver Parameter Setting
Attenuation Auto
Start ~ Stop Frequency 9kHz~150kHz / RB/VB 200Hz/1KHz for QP/Average
Start ~ Stop Frequency 150kHz~30MHz / RB/VB 9kHz/30KHz for QP/Average
Start ~ Stop Frequency 30MHz~1000MHz / RB/VB 120kHz/1MHz for QP

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 11 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

5.1.3. Test Procedures

1) Sequence of testing 9 kHz to 30 MHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna height is 0.8 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions

Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0° to 360°) and by rotating the elevation axes (0° to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to
the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be
stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

2) Sequence of testing 30 MHz to 1 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to
find the maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software maximize
the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable
angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the
premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

3) Sequence of testing 1 GHz to 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height scan range is 1 meter to 2.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with peak detection to find the
maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software maximize
the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter. This
procedure is repeated for both antenna polarizations.
--- The final measurement will be done in the position (turntable, EUT-table and antenna polarization)
causing the highest emissions with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position, antenna
polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of
the premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 14 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

4) Sequence of testing above 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.

Premeasurement:
--- The antenna is moved spherical over the EUT in different polarizations of the antenna.

Final measurement:
--- The final measurement will be performed at the position and antenna orientation for all detected
emissions that were found during the premeasurements with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and limit
will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

5.1.9. Results of Radiated Emissions (Above 1GHz)

Temperature 22.3℃ Humidity 52.3%
Test Engineer Wilson Hong Configurations TX

Reading Ant. Pre. Cab.
Freq. Measured Limit Margin
Level Fac. Fac. Loss Remark Pol.
MHz dBuV/m dBuV/m dB
dBuV dB/m dB dB
TX-Mode
1830.022 51.16 33.06 35.04 2.10 51.28 74.00 -22.72 Peak Horizontal
1830.022 44.96 33.06 35.04 2.10 45.08 54.00 -8.92 Average Horizontal
1830.022 52.27 33.06 35.04 2.10 52.39 74.00 -21.61 Peak Vertical
1830.022 47.22 33.06 35.04 2.10 47.34 54.00 -6.66 Average Vertical
2745.033 56.26 33.11 35.09 2.68 56.96 74.00 -17.04 Peak Horizontal
2745.033 42.36 33.11 35.09 2.68 43.06 54.00 -10.94 Average Horizontal
2745.033 61.03 33.11 35.09 2.68 61.73 74.00 -12.27 Peak Vertical
2745.033 44.36 33.11 35.09 2.68 45.06 54.00 -8.94 Average Vertical
3660.044 57.70 33.03 35.07 3.10 58.76 74.00 -15.24 Peak Horizontal
3660.044 42.34 33.03 35.07 3.10 43.4 54.00 -10.6 Average Horizontal
3660.044 60.38 33.03 35.07 3.10 61.44 74.00 -12.56 Peak Vertical
3660.044 43.80 33.03 35.07 3.10 44.86 54.00 -9.14 Average Vertical
9150.110 52.33 33.26 35.14 3.94 54.39 74.00 -19.61 Peak Horizontal
9150.110 44.93 33.26 35.14 3.94 46.99 54.00 -7.01 Average Horizontal
9150.110 56.77 33.26 35.14 3.94 58.83 74.00 -15.17 Peak Vertical
9150.110 47.64 33.26 35.14 3.94 49.7 54.00 -4.3 Average Vertical

Notes:
1). Measuring frequencies from 9 KHz~10th harmonic (ex. 10GHz), No emission found between lowest internal
used/generated frequency to 30MHz.
2). Radiated emissions measured in frequency range from 9k~10th harmonic (ex. 10GHz) were made with an
instrument using Peak detector mode.
3). No emission was be recorded above 18GHz means the reading of emissions are attenuated more than
20dB below the permissible limits or the field strength is too small to be measured.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 20 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

5.4. Antenna Requirements

5.4.1 Standard Applicable
According to antenna requirement of §15.203, an intentional radiator shall be designed to ensure that no
antenna other than that furnished by the responsible party shall be used with the device. The use of a
permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator
shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design
the unit so that a broken antenna can be re-placed by the user, but the use of a standard antenna jack or
electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices
operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this
requirement does not apply to intentional radiators that must be professionally installed, such as perimeter
protection systems and some field disturbance sensors, or to other intentional radiators which, in
accordance with Section 15.31(d), must be measured at the installation site. However, the installer shall
be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not
exceeded.

And according to §15.247(4)(1), system operating in the 2400-2483.5MHz bands that are used
exclusively for fixed, point-to-point operations may employ transmitting antennas with directional gain
greater than 6dBi provided the maximum peak output power of the intentional radiator is reduced by 1 dB
for every 3 dB that the directional gain of the antenna exceeds 6dBi.

5.4.2 Antenna Connected Construction
5.4.2.1. Standard Applicable

According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that
furnished by the responsible party shall be used with the device.

5.4.2.2. Antenna Connector Construction

The directional gains of antenna used for transmitting is -1.0dBi (Max.), and the antenna is an integral
antenna connect to PCB board and no consideration of replacement. Please see EUT photo for details.

5.4.2.3. Results: Compliance.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 26 of 28

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-SPR009 Report No.: LCS180718013AEA

7. TEST SETUP PHOTOGRAPHS OF EUT

Please refer to separated files for Test Setup Photos of the EUT.

8. EXTERIOR PHOTOGRAPHS OF THE EUT

Please refer to separated files for External Photos of the EUT.

9. INTERIOR PHOTOGRAPHS OF THE EUT

Please refer to separated files for Internal Photos of the EUT.

----------------THE END OF REPORT---------------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 28 of 28

Document Created: 2018-10-13 17:03:37
Document Modified: 2018-10-13 17:03:37

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC