Test Report

FCC ID: U5O-FIL085

Test Report

Download: PDF
FCCID_4171794

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA FCC TEST REPORT FOR NUM AXES CLASSIC DOG FENCE TRANSMITTER/CAT & SMALL DOG FENCE TRANSMITTER Test Model: PFFUGFIL085 Additional Model No.: PFFUGFIL061, PFFUGFIL079，PFFUGFIL060 Prepared for : NUM AXES Address : 745, rue de la Bergeresse ZAC des Aulnaies, OLIVET 45161, France Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an Address : District, Shenzhen, Guangdong, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : webmaster@LCS-cert.com Date of receipt of test sample : April 02, 2018 Number of tested samples : 1 Sample number : 180402140A Date of Test : April 02, 2018~May 03, 2018 Date of Report : December 25, 2018 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA FCC TEST REPORT FCC CFR 47 PART 15 C Report Reference No. ................. : LCS180402140AEA Date of Issue................................... : Dec 25, 2018 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Address ........................................... : Bao’an District, Shenzhen, Guangdong, China Full application of Harmonised standards ■ : Testing Location/ Procedure .......... Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ......................... : NUM AXES 745, rue de la Bergeresse ZAC des Aulnaies, OLIVET 45161, Address ........................................... : France Test Specification Standard ......................................... : FCC CFR 47 PART 15 C / ANSI C63.10: 2013 Test Report Form No. ..................... : LCSEMC-1.0 TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ..................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. CLASSIC DOG FENCE TRANSMITTER/CAT & SMALL DOG Test Item Description. .................. : FENCE TRANSMITTER Trade Mark ..................................... : Test Model ...................................... : PFFUGFIL085 DC 15V/150mA by power adapter Ratings ............................................ : Adapter input: AC120V,60Hz Result ........................................... : Positive Compiled by: Supervised by: Approved by: Calvin Weng/ Administrators Dick Su / Technique principal Gavin Liang/ Manager This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA FCC -- TEST REPORT December 25, 2018 Test Report No. : LCS180402140AEA Date of issue Test Model.............................. : PFFUGFIL061 CLASSIC DOG FENCE TRANSMITTER/CAT & SMALL DOG EUT......................................... : FENCE TRANSMITTER Applicant............................... : NUM AXES 745, rue de la Bergeresse ZAC des Aulnaies, OLIVET 45161, Address.................................. : France Telephone............................... : / Fax.......................................... : / Manufacturer........................ : NUM AXES 745, rue de la Bergeresse ZAC des Aulnaies, OLIVET 45161, Address................................... : France Telephone............................... : / Fax.......................................... : / Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA Revision History Revision Issue Date Revisions Revised By 000 December 25, 2018 Initial Issue Gavin Liang This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................ 6 1.1. Description of Device (EUT) ...................................................................................................................... 6 1.2. Support Equipment List .............................................................................................................................. 6 1.3. External I/O .................................................................................................................................................. 6 1.4. Description of Test Facility ........................................................................................................................ 6 1.5. Statement of the measurement uncertainty............................................................................................ 7 1.6. Measurement Uncertainty.......................................................................................................................... 7 1.7. Description of Test Modes ......................................................................................................................... 7 2. TEST METHODOLOGY ...................................................................................................................... 8 2.1. EUT Configuration ...................................................................................................................................... 8 2.2. EUT Exercise ............................................................................................................................................... 8 2.3. General Test Procedures........................................................................................................................... 8 2.3.1 Conducted Emissions .............................................................................................................................. 8 2.3.2 Radiated Emissions .................................................................................................................................. 8 3. CONNECTION DIAGRAM OF TEST SYSTEM............................................................................... 9 3.1. Justification .................................................................................................................................................. 9 3.2. EUT Exercise Software .............................................................................................................................. 9 3.3. Special Accessories.................................................................................................................................... 9 3.4. Block Diagram/Schematics ....................................................................................................................... 9 3.5. Equipment Modifications ............................................................................................................................ 9 3.6. Test Setup .................................................................................................................................................... 9 4. SUMMARY OF TEST RESULTS ..................................................................................................... 10 5. POWER LINE CONDUCTED EMISSIONS.................................................................................... 11 6. RADIATED EMISSION MEASUREMENT...................................................................................... 13 7. 99% AND 20 DB BANDWIDTH MEASUREMENT ....................................................................... 19 8. ANTENNA REQUIREMENTS .......................................................................................................... 21 9. LIST OF MEASURING EQUIPMENT ............................................................................................. 22 10. TEST SETUP PHOTOGRAPHS .................................................................................................... 23 11. EXTERIOR HOTOGRAPHS ........................................................................................................... 23 12. INTERIOR PHOTOGRAPHS ......................................................................................................... 23 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 5 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 1. GENERAL INFORMATION 1.1. Description of Device (EUT) CLASSIC DOG FENCE TRANSMITTER/CAT & SMALL EUT DOG FENCE TRANSMITTER Test Model PFFUGFIL085 Additional Model(s) PFFUGFIL061, PFFUGFIL079, PFFUGFIL060 All the structure, PCB is the same except the model name Model Declaration is different, so no additional model is tested. Hardware Version CPSSECAR143 Software Version CPELEPRG086 Version Géné-2-H DC 15V/150mA by power adapter Power Supply Adapter input: AC120V,60Hz Wireless technology Frequency Range 20KHz Channel Spacing N/A Channel Number 1 channel Modulation Type OOK Antenna Description External Antenna, 0dBi (Max.) 1.2. Support Equipment List Manufacturer Description Model Serial Number Certificate HON KWANG Power adapter D7300-01 -- FCC VOC ELECTRIC CO LTD -- -- -- -- -- 1.3. External I/O I/O Port Description Quantity Cable DC in port 1 N/A 1.4. Description of Test Facility FCC Registration Number. is 254912. Industry Canada Registration Number. is 9642A-1. ESMD Registration Number. is ARCB0108. UL Registration Number. is 100571-492. TUV SUD Registration Number. is SCN1081. TUV RH Registration Number. is UA 50296516-001 NVLAP Registration Code is 600167-0 The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.4:2014 and CISPR 16-1-4:2010 SVSWR requirement for radiated emission above 1GHz. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 6 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 1.5. Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. To CISPR 16 – 4 “Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements” and is documented in the LCS quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. 1.6. Measurement Uncertainty Test Item Frequency Range Uncertainty Note 9KHz~30MHz 3.10dB (1) 30MHz~200MHz 2.96dB (1) Radiation Uncertainty : 200MHz~1000MHz 3.10dB (1) 1GHz~26.5GHz 4.00dB (1) Conduction Uncertainty : 150kHz~30MHz 1.63dB (1) Power disturbance : 30MHz~300MHz 1.60dB (1) (1). This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. 1.7. Description of Test Modes The EUT operates at 20 KHz. The following operating modes were applied for the related test items. All test modes were tested, only the result of the worst case was recorded in the report. It was pre-tested on the positioned of each 3 axis. The worst case was found positioned on X-plane. Transmitting Frequency Mode of Operations (KHz) OOK 20 For Conducted Emission Test Mode TX Mode For Radiated Emission Test Mode TX Mode ***Note: Using a temporary antenna connector for the EUT when the conducted measurements are performed. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 7 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 2. TEST METHODOLOGY All measurements contained in this report were conducted with ANSI C63.10: 2013, American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. All radiated and conducted emissions measurement was performed at Shenzhen LCS Compliance Testing Laboratory Ltd. 2.1. EUT Configuration The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 2.2. EUT Exercise The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.201, 15.203, 15.205, 15.207, 15.209 under the FCC Rules Part 15 Subpart C. 2.3. General Test Procedures 2.3.1 Conducted Emissions According to the requirements in Section 6.2 of ANSI C63.10: 2013, AC power-line conducted emissions shall be measured in the frequency range between 0.15 MHz and 30MHz using Quasi-peak and average detector modes. 2.3.2 Radiated Emissions The EUT is placed on a turn table and the turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 6.3 of ANSI C63.10: 2013. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 8 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 3. CONNECTION DIAGRAM OF TEST SYSTEM 3.1. Justification The system was configured for testing in a continuous transmitting condition. 3.2. EUT Exercise Software Powered on the EUT then the EUT will transmit at 20 KHz. 3.3. Special Accessories N/A 3.4. Block Diagram/Schematics Please refer to the related document 3.5. Equipment Modifications Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT. 3.6. Test Setup Please refer to the test setup photo. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 9 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 4. SUMMARY OF TEST RESULTS Applied Standard: FCC Part 15 Subpart C FCC Rules Description Of Test Result §15.203 Antenna Requirement Compliant §15.207(a) Power Line Conducted Emissions Compliant §15.201(a), §15.205(a), Radiated Emissions Measurement Compliant §15.209(a), §15.215(a) §2.1049 99% and 20dB Bandwidth Compliant §15.215 Remark: Note 1 --- Test results inside test report. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 10 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 5. POWER LINE CONDUCTED EMISSIONS 5.1 Standard Applicable According to §15.207 (a): For an intentional radiator which is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed 250 microvolts (The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz). The limits at specific frequency range is listed as follows: Frequency Range Limits (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56 56 to 46 0.50 to 5 56 46 5 to 30 60 50 * Decreasing linearly with the logarithm of the frequency 5.2 Block Diagram of Test Setup 5.3 Test Results PASS. The test data please refer to following page. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 11 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA AC Conducted Emission of charge from power adapter mode @ AC 120V/60Hz @ (worst case) Line Neutral ***Note: Pre-scan all modes and recorded the worst case results in this report. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 12 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 6. RADIATED EMISSION MEASUREMENT 6.1. Standard Applicable According to FCC §15.201 (a) “Intentional radiators operated as carrier current systems, devices operated under the provisions of §§15.211, 15.213, and 15.221, and devices operating below 490 kHz in which all emissions are at least 40 dB below the limits in §15.209 are subject to Suppliers Declaration of Conformity pursuant to the procedures in subpart J of part 2 of this chapter prior to marketing.” Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 6.2. Instruments Setting Please refer to of equipment list in this report. The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RB / VB (Emission in restricted band) 1MHz / 1MHz for Peak, 1 MHz / 1/B kHz for Average RB / VB (Emission in non-restricted band) 1MHz / 1MHz for Peak, 1 MHz / 1/B kHz for Average Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~150kHz / RB/VB 200Hz/1KHz for QP/AVG Start ~ Stop Frequency 150kHz~30MHz / RB/VB 9kHz/30KHz for QP/AVG Start ~ Stop Frequency 30MHz~1000MHz / RB/VB 120kHz/1MHz for QP This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 13 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 6.3. Test Procedure 1) Sequence of testing 9 kHz to 30 MHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used. --- If the EUT is a floor standing device, it is placed on the ground. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions. --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 3 meter. --- The EUT was set into operation. Premeasurement: --- The turntable rotates from 0° to 315° using 45° steps. --- The antenna height is 0.8 meter. --- At each turntable position the analyzer sweeps with peak detection to find the maximum of all emissions Final measurement: --- Identified emissions during the premeasurement the software maximizes by rotating the turntable position (0° to 360°) and by rotating the elevation axes (0° to 360°). --- The final measurement will be done in the position (turntable and elevation) causing the highest emissions with QPK detector. --- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 14 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 2) Sequence of testing 30 MHz to 1 GHz Setup: --- The equipment was set up to simulate a typical usage like described in the user manual or described by manufacturer. --- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane. --- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both. --- Auxiliary equipment and cables were positioned to simulate normal operation conditions --- The AC power port of the EUT (if available) is connected to a power outlet below the turntable. --- The measurement distance is 3 meter. --- The EUT was set into operation. Premeasurement: --- The turntable rotates from 0° to 315° using 45° steps. --- The antenna is polarized vertical and horizontal. --- The antenna height changes from 1 to 3 meter. --- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to find the maximum of all emissions. Final measurement: --- The final measurement will be performed with minimum the six highest peaks. --- According to the maximum antenna and turntable positions of premeasurement the software maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter. --- The final measurement will be done with QP detector with an EMI receiver. --- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement with marked maximum final measurements and the limit will be stored. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 15 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 6.4. Block Diagram of Test Setup Above 18 GHz shall be extrapolated to the specified distance using an extrapolation factor of 20 dB/decade form 3m to 1m. Distance extrapolation factor = 20 log (specific distanc [3m] / test distance [1m]) (dB); Limit line = specific limits (dBuV) + distance extrapolation factor [6 dB]. 6.5. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 16 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 6.6. Results of Radiated Emissions (9 KHz~30MHz) Note: The amplitude of spurious emissions which are attenuated by more than 20 dB below the permissible value has no need to be reported. Distance extrapolation factor = 40 log (specific distance / test distance) (dB); Limit line = specific limits (dBuV) + distance extrapolation factor. 6.7. Results of Radiated Emissions (30 MHz~1000 MHz) PASS. Only record the worst test result in this report. The test data please refer to following page. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 17 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA Horizontal Vertical ***Note: 1). Pre-scan all modes and recorded the worst case results in this report (TX). 2). Emission level (dBuV/m) = 20 log Emission level (uV/m). 3). Corrected Reading: Antenna Factor + Cable Loss + Read Level = Level. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 18 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 7. 99% AND 20 DB BANDWIDTH MEASUREMENT 7.1. Standard Applicable According to §15.215, device must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. According to §2.1049, The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured under the following conditions as applicable. 7.2. Block Diagram of Test Setup 7.3. Test Procedure Use the following spectrum analyzer settings: Span = 3 KHz RBW = 100 Hz VBW = 300 Hz Sweep = auto Detector function = peak Trace = max hold The EUT should be transmitting at its maximum data rate. Allow the trace to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 20 dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 20 dB bandwidth of the emission. If this value varies with different modes of operation (e.g., data rate, modulation format, etc.), repeat this test for each variation. The limit is specified in one of the subparagraphs of this Section. Submit this plot(s). 7.4. Test Results Test Result Of 99% and 20dB Bandwidth Measurement Test Frequency 99% Bandwidth 20dB Bandwidth Limit (KHz) (Hz) (Hz) (MHz) 20.00 209.00 247.00 No Limit Remark: 1. Test results including cable loss; 2. Please refer to following test plots; This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 19 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 20 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 8. ANTENNA REQUIREMENTS 8.1 Standard Applicable According to antenna requirement of §15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be re-placed by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 8.2 Antenna Connected Construction 8.2.1. Standard Applicable According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 8.2.2. Antenna Connector Construction The antenna gain used for transmitting is 0dBi, the EUT use external antenna and a unique antenna connector. Please see EUT photo for details. 8.2.3. Results: Compliance. This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 21 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 9. LIST OF MEASURING EQUIPMENT Item Equipment Manufacturer Model No. Serial No. Last Cal. Next Cal. 1 Power Meter R&S NRVS 100444 2017-06-17 2018-06-16 2 Power Sensor R&S NRV-Z81 100458 2017-06-17 2018-06-16 3 Power Sensor R&S NRV-Z32 10057 2017-06-17 2018-06-16 EPM Series Power 4 Agilent E4419B MY45104493 2017-06-17 2018-06-16 Meter E-SERIES AVG 5 Agilent E9301H MY41495234 2017-06-17 2018-06-16 POWER SENSOR ESA-E SERIES 6 SPECTRUM Agilent E4407B MY41440754 2017-11-18 2018-11-17 ANALYZER 7 MXA Signal Analyzer Agilent N9020A MY49100040 2017-06-17 2018-06-16 SPECTRUM 8 R&S FSP 100503 2017-06-17 2018-06-16 ANALYZER 3m Semi Anechoic 9 SIDT FRANKONIA SAC-3M 03CH03-HY 2017-06-17 2018-06-16 Chamber 10 Positioning Controller MF MF-7082 / 2017-06-17 2018-06-16 11 EMI Test Software AUDIX E3 N/A N/A N/A 12 EMI Test Receiver ROHDE & SCHWARZ ESR 7 101181 2017-06-17 2018-06-16 13 AMPLIFIER QuieTek QTK-A2525G CHM10809065 2017-11-18 2018-11-17 14 Active Loop Antenna SCHWARZBECK FMZB 1519B 00005 2017-06-23 2018-06-22 15 By-log Antenna SCHWARZBECK VULB9163 9163-470 2017-05-02 2018-05-01 16 Horn Antenna EMCO 3115 6741 2017-06-23 2018-06-22 17 RF Cable-R03m Jye Bao RG142 CB021 2017-06-17 2018-06-16 18 RF Cable-HIGH SUHNER SUCOFLEX 106 03CH03-HY 2017-06-17 2018-06-16 19 TEST RECEIVER R&S ESCI 101142 2017-06-17 2018-06-16 20 RF Cable-CON UTIFLEX 3102-26886-4 CB049 2017-06-17 2018-06-16 21 10dB Attenuator SCHWARZBECK MTS-IMP136 261115-001-0032 2017-06-17 2018-06-16 22 Artificial Mains R&S ENV216 101288 2017-06-17 2018-06-16 X-series USB Peak and 23 Average Power Sensor Agilent U2021XA MY54080022 2017-10-27 2018-10-26 Aglient 4 CH. Simultaneous 24 Agilent U2531A MY54080016 2017-10-27 2018-10-26 Sampling 14 Bits 2MS/s 25 Test Software Ascentest AT890-SW 20160630 N/A N/A 26 RF Control Unit Ascentest AT890-RFB N/A 2017-06-17 2018-06-16 This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 22 of 23

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: U5O-FIL085 Report No.:LCS180402140AEA 10. TEST SETUP PHOTOGRAPHS Please refer to separated files for Test Setup Photos of the EUT. 11. EXTERIOR HOTOGRAPHS Please refer to separated files for External Photos of the EUT. 12. INTERIOR PHOTOGRAPHS Please refer to separated files for Internal Photos of the EUT. ------------THE END OF TEST REPORT---------- This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 23 of 23


Document Created: 2019-02-18 23:47:29
Document Modified: 2019-02-18 23:47:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC