Test report

FCC ID: U4GJX2WB

Test Report

Download: PDF
FCCID_2438157

FCC Measurement/Technical Report on WLAN transceiver incorporated in Mobile Handheld Computer Datalogic Joya X2 BASIC Wifi with DE2011 reader FCC ID: U4GJX2W IC: 3862E-JX2W and WLAN transceiver incorporated in Datalogic Joya X2 PLUS Wifi + BT with SE4500 reader FCC ID: U4GJX2WB IC: 3862E-JX2WB Report Reference: MDE_DATA_1408_FCCe Test Laboratory: Borsigstrasse 11 Germany 7Layers AG 40880 Ratingen Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7 layers AG Aufsichtsratsvorsitzender Registergericht registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Peter Mertel USt-IdNr  VAT No.: Phone: +49 (0) 2102 749 0 Vorstand Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. H.-J. Meckelburg TAX No. 147/5869/0385 www.7Layers.com Dr. H. Ansorge

Table of Contents 0 Applied Standards and Test Summary 3 0.1 Technical Report Summary 3 0.2 FCC and IC Correlation Table 4 0.3 Measurement Summary 5 0.4 Revision History 6 1 Administrative Data 7 1.1 Testing Laboratory 7 1.2 Project Data 7 1.3 Applicant Data 7 1.4 Manufacturer Data 7 2 Test object Data 8 2.1 General EUT Description 8 2.2 EUT Main components 9 2.3 Ancillary Equipment 9 2.4 Auxiliary Equipment 9 2.5 EUT Setups 9 2.6 Operating Modes 10 2.7 Special software used for testing 11 2.8 Product labelling 11 3 Test Results 12 3.1 Spurious radiated emissions 12 3.2 Band edge compliance 20 4 Test Equipment 23 5 Photo Report 31 6 Setup Drawings 31 Test report Reference: MDE_DATA_1408_FCCe Page 2 of 31

0 Applied Standards and Test Summary 0.1 Technical Report Summary Type of Authorization Certification for an Intentional Radiator (Digital Device / Spread Spectrum). Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-13 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz Note: The tests were selected and performed with reference to the FCC Public Notice “Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS)Operating Under §15.247, 558074 D01 DTS Meas Guidance v03r02, 2014-06-05”. Instead of applying ANSI C63.4–1992 which is referenced in the FCC Public Note, the newer ANSI C63.4–2009 is applied. Summary Test Results: The EUT complied with all performed tests as listed in chapter 0.3 Measurement Summary. Test report Reference: MDE_DATA_1408_FCCe Page 3 of 31

0.2 FCC and IC Correlation Table Correlation of measurement requirements for DTS devices (e.g. WLAN 2.4/5 GHz) equipment The following tables show the correlation of measurement requirements for DTS (e.g. WLAN) equipment and Information Technology Equipment (ITE) from FCC and IC standards. DTS equipment Measurement FCC reference IC reference Conducted emissions on § 15.207 RSS-Gen Issue 3: 7.2.4 AC Mains Occupied bandwidth § 15.247 (a) (2) RSS-210 Issue 8: A8.2 (a) Peak power output § 15.247 (b) (3), (4) RSS-210 Issue 8: A8.4 (4) Spurious RF conducted § 15.247 (d) RSS-Gen Issue 3: 6; emissions RSS-210 Issue 8: A8.5 Spurious radiated emissions § 15.247 (d); RSS-Gen Issue 3: 6; § 15.209 (a) RSS-210 Issue 8: A8.5 Band edge compliance § 15.247 (d) RSS-210 Issue 8: A8.5 Power density § 15.247 (e) RSS-210 Issue 8: A8.2 (b) Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 3: 7.1.2 Receiver spurious emissions – RSS-210 Issue 8: 2.3 RSS Gen Issue 3: 6 *) *) Receivers which are part of Transceivers are exempted with respect to Notice 2012-DRS0126. Information Technology Equipment (ITE) Measurement FCC reference IC reference Conducted emissions on § 15.107 ICES-003 Issue 5: 6.1 AC Mains Spurious Radiated Emissions § 15.109 ICES-003 Issue 5: 6.2 Test report Reference: MDE_DATA_1408_FCCe Page 4 of 31

0.3 Measurement Summary FCC Part 15, Subpart C § 15.207 Conducted emissions (AC power line) The measurement was performed according to ANSI C63.4 2009 Setup Port Final Result - AC port N/A FCC Part 15, Subpart C § 15.247 (a) (1) Occupied bandwidth The measurement was performed according to FCC § 15.31 10-1-13 Edition Setup Port Final Result Setup_01 Temp.ant.connector Not performed FCC Part 15, Subpart C § 15.247 (b) (1) Peak power output The measurement was performed according to FCC § 15.31 10-1-13 Edition Setup Port Final Result - Temp.ant.connector Not performed FCC Part 15, Subpart C § 15.247 (d), § 15.35 (b), § 15.207 Spurious conducted emissions The measurement was performed according to ANSI C63.4 2009 Setup Port Final Result - Temp.ant.connector Not performed FCC Part 15, Subpart C § 15.247 (d), § 15.35 (b), § 15.209 Spurious radiated emissions The measurement was performed according to ANSI C63.4 2009 Setup Port Final Result Setup_01 Enclosure passed Setup_02 Enclosure passed FCC Part 15, Subpart C § 15.247 (d) Band edge compliance The measurement was performed according to FCC § 15.31 / 10-1-13 Edition / ANSI C63.4 2009 Setup Port Final Result Setup_01 Enclosure passed Setup_02 Enclosure passed FCC Part 15, Subpart C § 15.247 (e) Power density The measurement was performed according to FCC § 15.31 10-1-13 Edition Setup Port Final Result - Temp.ant.connector Not performed N/A not applicable (the EUT is powered by DC) Test report Reference: MDE_DATA_1408_FCCe Page 5 of 31

layers testing for a smarter world / Responsible for f Responsible Q /(/ Accreditation Scope: . for Test Report: " This report contains only the applicable radiated tests. The applicable conducted tests were tested and reported by another laboratory. 0.4 Revision History Report version control Version Release date Change Description Version validity Initial 2014—10—10 &= Not valid RevO1 2014—10—22 test results for Bluetooth removed; valid editorial corrections Test report Reference: MDE_DATA_1408_FCCe Page 6 of 31

1 Administrative Data 1.1 Testing Laboratory Company Name: 7 Layers AG Address Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716 . The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no.: DAkkS D-PL-12140-01-01 Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Robert Machulec Dipl.-Ing. Thomas Hoell Dipl.-Ing. Andreas Petz Dipl.-Ing. Marco Kullik Report Template Version: 2014-08-26 1.2 Project Data Responsible for testing and report: Dipl.-Ing. Daniel Gall Date of Test(s): 2014-05-27 to 2014-07-25 Date of Report: 2014-10-22 1.3 Applicant Data Company Name: Datalogic ADC s.r.l. Address: Via S. Vitalino, 13 40012 Lippo di Calderara di Reno, Bologna Italy Contact Person: Mr. Eucarpio Guarisco 1.4 Manufacturer Data Company Name: Please see applicant data Address: Contact Person: Test report Reference: MDE_DATA_1408_FCCe Page 7 of 31

2 Test object Data 2.1 General EUT Description Equipment under Test: IEEE 802.11b/g/n WLAN transceiver Type Designation: Datalogic Joya X2 and Joya X2 PLUS Kind of Device: Mobile Handheld Computer (optional) Voltage Type: DC Voltage Level: 3.7 V Tested Modulation Type: WLAN: DBPSK; OFDM:BPSK General product description: The WLAN transceiver is incorporated in a mobile handheld computer, which runs with Windows Mobile 6 CE. Specific product description for the EUT: The focus of this test report is the WLAN transceiver of the Datalogic Joya X2 family, consequently switched on the IEEE 802.11 b/g/n modes, working in the 2.4 GHz band. The tested representative variants are “PLUS” including WLAN and Bluetooth and “BASIC” containing WLAN radio only. The EUT provides the following ports: Ports Enclosure System-port The main components of the EUT are listed and described in Chapter 2.2 Test report Reference: MDE_DATA_1408_FCCe Page 8 of 31

2.2 EUT Main components Type, S/N, Short Descriptions etc. used in this Test Report Short Equipment Type Serial No. HW Status SW Status Description under Test Designation EUT A WLAN (& BT) Datalogic Joya Z14P00157 P/N: 1.80.024.04- (Code: transceiver X2 PLUS Wifi 911300127 SS000 DE1006006ba01) + BT with SE4500 reader Remark: EUT A is equipped with two integral antennas. For Bluetooth an integrated chip antenna with a gain of about 2dB is used. For Wifi a single band antenna with a gain of 3.7dB is used. EUT B WLAN Datalogic Joya Z14P00100 P/N: 1.80.024.04- (Code: transceiver X2 BASIC Wifi 911300120 SS000 DE1006006da01) with DE2011 reader Remark: EUT B is equipped with one integral. A single band antenna with a gain of 3.7dB is used. NOTE: The short description used to simplify the identification of the EUT in this test report. 2.3 Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment, which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Short Equipment under Type Designation Serial No. HW SW Description Test Status Status - – – – – – 2.4 Auxiliary Equipment For the purposes of this test report, auxiliary equipment is defined as equipment, which is used temporarily to enable operational and control features especially used for the tests of the EUT, which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Short Equipment under Type Designation Serial No. HW SW Description Test Status Status - – – – – – 2.5 EUT Setups This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale Setup_01 EUT A Setup for radiated radio measurements variant “PLUS” Setup_02 EUT B Setup for radiated radio measurements variant “BASIC” Test report Reference: MDE_DATA_1408_FCCe Page 9 of 31

2.6 Operating Modes This chapter describes the operating modes of the EUTs used for testing. 2.6.1 Test Channels Band: WLAN 2.4 GHz ISM 2400 - 2483.5 MHz Bottom Middle Top 1 6 11 2412 2437 2462 2.6.2 Datarates SISO: WLAN b-mode; 20 MHz; 1 Mbit/s; DSSS Modulation WLAN g-mode; 20 MHz; 6 Mbit/s; OFDM Modulation WLAN n-mode; 20 MHz; 6.5 Mbit/s; OFDM Modulation The g-mode was selected as “worst case” for OFDM Modulation. Consequently the testing was performed in b-mode and in g-Mode (and not in n-mode). Test report Reference: MDE_DATA_1408_FCCe Page 10 of 31

2.7 Special software used for testing The Windows program “SRU” is used to control the WLAN module which was provided by the applicant. 2.8 Product labelling 2.8.1 FCC ID label Please refer to the documentation of the applicant. 2.8.2 Location of the label on the EUT Please refer to the documentation of the applicant. Test report Reference: MDE_DATA_1408_FCCe Page 11 of 31

3 Test Results 3.1 Spurious radiated emissions Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.4 3.1.1 Test Description The test set-up was made in accordance to the general provisions of ANSI C63.4 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non- conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software ES-K1 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is performed at 2 axes. A pre-check is performed while the EUT is powered from a DC power sourse. 1. Measurement up to 30 MHz The Loop antenna HFH2-Z2 is used. Step 1: pre measurement - Anechoic chamber - Antenna distance: 10 m - Detector: Peak-Maxhold - Frequency range: 0.009 - 0.15 MHz and 0.15 – 30 MHz - Frequency steps: 0.1 kHz and 5 kHz - IF–Bandwidth: 0.2 kHz and 10 kHz - Measuring time / Frequency step: 100 ms Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: final measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is to find the maximum emission level. - Open area test side - Antenna distance: according to the Standard - Detector: Quasi-Peak - Frequency range: 0.009 – 30 MHz - Frequency steps: measurement at frequencies detected in step 1 - IF–Bandwidth: 0.2 - 10 kHz - Measuring time / Frequency step: 100 ms Test report Reference: MDE_DATA_1408_FCCe Page 12 of 31

2. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold - Frequency range: 30 – 1000 MHz - Frequency steps: 60 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 µs - Turntable angle range: –180° to 180° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: second measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is, to find out the approximate turntable angle and antenna height for each frequency. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: –180° to 180° - Turntable step size: 45° - Height variation range: 1 – 4 m - Height variation step size: 0.5 m - Polarisation: horizontal + vertical After this step, the EMI test system has determined the following values for each frequency (of step 1): - Frequency - Azimuth value (of turntable) - Antenna height The last two values have now the following accuracy: - Azimuth value (of turntable): 45° - Antenna height: 0.5 m Step 3: final measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 22.5° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 25 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 22.5 ° around the determined value - Height variation range: ± 25 cm around the determined value Test report Reference: MDE_DATA_1408_FCCe Page 13 of 31

Step 4: final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: The Equipment Under Test (EUT) was set up on a non-conductive support at 1.4 m height in the fully-anechoic chamber. The measurement distance was reduced to 1 m. The results were extrapolated by the extrapolation factor of 20 dB/decade (inverse linear-distance for field strength measurements, inverse linear-distance squared for the power reference level measurements). Due to the fact, that in this frequency range a double-ridged wave guided horn antenna (up to 18 GHz) and a horn antenna (18–25 GHz) are used, the steps 2-4 are omitted. Step 1 was performed with one height of the receiving antenna only. EMI receiver settings: - Detector: Peak, Average - IF Bandwidth = 1 MHz For the data rate in mode n the test is performed as worst-case-check in order to verify that emissions have a comparable level as found at modes b and g. Typically, the measurement is performed in the frequency range 1 to 8 GHz but it depends on the emissions found during the test for the modes b and g. Please refer to the results for the used frequency range. 3.1.2 Test Requirements / Limits FCC Part 15, Subpart C, §15.247 (e) For digitally modulated systems, the peak power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. … The same method of determining the conducted output power shall be used to determine the power spectral density. Test report Reference: MDE_DATA_1408_FCCe Page 14 of 31

3.1.3 Test Requirements / Limits FCC Part 15, Subpart C, §15.247 (d) ... In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Calculated Limits(dBµV/m Frequency in MHz Limit (µV/m) Limits(dBµV/m @10m) distance (m) @10m) 0.009 – 0.49 2400/F(kHz) 300 59.1 dB (48.5 – 13.8) + 30 dB 78.5 – 43.8 0.49 – 1.705 24000/F(kHz) 30 19.1 dB (48.9 – 23.0) + 10 dB 58.9 – 33.0 1.705 – 30 30 30 19.1 dB 29.5 + 10 dB 39.5 Measurement Frequency in MHz Limit (µV/m) Limit (dBµV/m) distance (m) 30 – 88 100 3 40.0 88 – 216 150 3 43.5 216 – 960 200 3 46.0 above 960 500 3 54.0 §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) Test report Reference: MDE_DATA_1408_FCCe Page 15 of 31

3.1.4 Test Protocol Temperature: 23–27 °C Air Pressure: 997-1011 hPa Humidity: 33–50 % WLAN b-Mode; 20 MHz; 1 Mbit/s Channel Center Spurious Margin Ch. Frequency Frequency Level RBW Limit to Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Joya X2 Variant “PLUS” 1/78 2412/2480 2333.0 50.4 PK 1000 74.0 23.6 1/78 2412/2480 2333.0 41.2 AV 1000 54.0 12.8 1/78 2412/2480 2491.0 56.0 PK 1000 74.0 18.0 1/78 2412/2480 2491.0 48.6 AV 1000 54.0 5.4 1/78 2412/2480 4824.0 41.35 PK 1000 74.0 32.65 1/78 2412/2480 4824.0 34.85 AV 1000 54.0 19.15 6/39 2437/2441 2358.0 52.2 PK 1000 74.0 21.8 6/39 2437/2441 2358.0 42.0 AV 1000 54.0 12.0 6/39 2437/2441 7312.0 44.33 PK 1000 74.0 29.67 6/39 2437/2441 7312.0 36.36 AV 1000 54.0 17.64 11/0 2462/2402 1602.0 47.5 PK 1000 74.0 26.5 11/0 2462/2402 1602.0 37.8 AV 1000 54.0 16.2 11/0 2462/2402 2383.0 52.8 PK 1000 74.0 21.2 11/0 2462/2402 2383.0 43.8 AV 1000 54.0 10.2 11/0 2462/2402 2483.0 50.5 PK 1000 74.0 23.5 11/0 2462/2402 2483.0 39.3 AV 1000 54.0 14.7 11/0 2462/2402 7385.0 45.6 PK 1000 74.0 28.4 11/0 2462/2402 7385.0 38.2 AV 1000 54.0 15.8 Note: No (further) spurious emissions in the range 20 dB below the limit found. During testing also the Bluetooth Transceiver was switched on (BT FSK modulation, 1-DH1). Test report Reference: MDE_DATA_1408_FCCe Page 16 of 31

WLAN b-Mode; 20 MHz; 1 Mbit/s Channel Center Spurious Margin Ch. Frequency Frequency Level RBW Limit to Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Joya X2 Variant “BASIC” 1 2412 1235.0 45.3 PEAK 1000 74.0 28.7 1 2412 2333.0 35.7 AV 1000 54.0 18.4 1 2412 2333.0 52.1 PEAK 1000 74.0 21.9 1 2412 2333.0 43.7 AV 1000 54.0 10.3 1 2412 2387.0 51.5 PEAK 1000 74.0 22.6 1 2412 2387.0 42.1 AV 1000 54.0 11.9 1 2412 2491.0 58.1 PEAK 1000 74.0 15.9 1 2412 2491.0 51.7 AV 1000 54.0 2.3 1 2412 4824.0 41.8 PEAK 1000 74.0 32.2 1 2412 4824.0 37.4 AV 1000 54.0 16.6 6 2437 1235.0 45.5 PEAK 1000 74.0 28.5 6 2437 1235.0 35.7 AV 1000 54.0 18.3 6 2437 2356.0 53.7 PEAK 1000 74.0 20.3 6 2437 2356.0 44.9 AV 1000 54.0 9.1 6 2437 4874.0 41.3 PEAK 1000 74.0 32.7 6 2437 4874.0 36.5 AV 1000 54.0 17.5 6 2437 7310.0 44.6 PEAK 1000 74.0 29.5 6 2437 7310.0 35.3 AV 1000 54.0 18.7 11 2462 1235.0 46.1 PEAK 1000 74.0 27.9 11 2462 1235.0 35.7 AV 1000 54.0 18.4 11 2462 2383.0 53.1 PEAK 1000 74.0 20.9 11 2462 2383.0 44.7 AV 1000 54.0 9.3 11 2462 2487.0 51.2 PEAK 1000 74.0 22.9 11 2462 2487.0 40.0 AV 1000 54.0 14.0 11 2462 7387.0 44.1 PEAK 1000 74.0 29.9 11 2462 7387.0 36.0 AV 1000 54.0 18.0 Note: No (further) spurious emissions in the range 20 dB below the limit found. The measurement was performed from 9 kHz up to 8 GHz because at pre-measurements no significant spurious emissions have been found outside this frequency range. Test report Reference: MDE_DATA_1408_FCCe Page 17 of 31

WLAN g-Mode; 20 MHz; 6 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Joya X2 Variant “PLUS” 1/78 2412/2480 2338.0 50.9 PEAK 1000 74.0 23.1 1/78 2412/2480 2338.0 39.2 AV 1000 54.0 14.8 1/78 2412/2480 2390.0 60.6 PEAK 1000 74.0 13.4 1/78 2412/2480 2390.0 46.0 AV 1000 54.0 8.0 1/78 2412/2480 2488.0 58.3 PEAK 1000 74.0 15.7 1/78 2412/2480 2488.0 47.6 AV 1000 54.0 6.4 6/39 2437/2441 2360.0 52.7 PEAK 1000 74.0 21.3 6/39 2437/2441 2360.0 41.1 AV 1000 54.0 12.9 6/39 2437/2441 2483.5 51.7 PEAK 1000 74.0 22.3 6/39 2437/2441 2483.5 39.3 AV 1000 54.0 14.7 6/39 2437/2441 7312.0 51.1 PEAK 1000 74.0 22.9 6/39 2437/2441 7312.0 36.0 AV 1000 54.0 18.0 11/0 2462/2402 1602.0 47.3 PEAK 1000 74.0 26.7 11/0 2462/2402 1602.0 37.8 AV 1000 54.0 16.2 11/0 2462/2402 2383.0 51.1 PEAK 1000 74.0 22.9 11/0 2462/2402 2383.0 39.9 AV 1000 54.0 14.1 11/0 2462/2402 2483.0 60.8 PEAK 1000 74.0 13.2 11/0 2462/2402 2483.0 44.8 AV 1000 54.0 9.2 Note: No (further) spurious emissions in the range 20 dB below the limit found. The measurements were performed from 1 GHz up to 8 GHz because at pre-measurements no significant spurious emissions have been found outside this frequency range. During testing also the Bluetooth Transceiver was switched on (BT PSK modulation, 2-DH1). Test report Reference: MDE_DATA_1408_FCCe Page 18 of 31

WLAN g-Mode; 20 MHz; 6 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Joya X2 Variant “BASIC” 1 2412 1235.0 45.1 PEAK 1000 74.0 28.9 1 2412 1235.0 35.4 AV 1000 54.0 18.6 1 2412 2333.0 51.2 PEAK 1000 74.0 22.9 1 2412 2333.0 40.0 AV 1000 54.0 14.0 1 2412 2390.0 62.5 PEAK 1000 74.0 11.5 1 2412 2390.0 47.0 AV 1000 54.0 7.0 1 2412 2493.0 57.7 PEAK 1000 74.0 16.3 1 2412 2493.0 46.9 AV 1000 54.0 7.1 6 2437 1235.0 45.6 PEAK 1000 74.0 28.4 6 2437 1235.0 35.7 AV 1000 54.0 18.4 6 2437 2356.0 54.9 PEAK 1000 74.0 19.2 6 2437 2356.0 44.2 AV 1000 54.0 9.8 6 2437 2483.5 52.6 PEAK 1000 74.0 21.4 6 2437 2483.5 40.9 AV 1000 54.0 13.2 11 2462 1235.0 45.0 PEAK 1000 74.0 29.0 11 2462 1235.0 35.5 AV 1000 54.0 18.5 11 2462 2383.0 53.3 PEAK 1000 74.0 20.7 11 2462 2383.0 41.8 AV 1000 54.0 12.2 11 2462 2483.5 64.5 PEAK 1000 74.0 9.5 11 2462 2483.5 47.9 AV 1000 54.0 6.1 Note: No (further) spurious emissions in the range 20 dB below the limit found. The measurements were performed from 1 GHz up to 8 GHz because at pre-measurements no significant spurious emissions have been found outside this frequency range. Test report Reference: MDE_DATA_1408_FCCe Page 19 of 31

3.2 Band edge compliance Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.4–2009, FCC §15.31 3.2.1 Test Description The procedure to show compliance with the band edge requirement is divided into two measurements: 1. Show compliance of the lower and higher band edge by a conducted measurement. For the conducted measurement, the Equipment Under Test (EUT) is placed in a shielded room. For the lower band edge the EUT is set to transmit as follows: For a WLAN transmitter working in the 2.4 GHz band on lowest channel: CH1 = 2412 MHz / CH3 = 2422 MHz for a channel bandwidth of 20 / 40 MHz. The lower band edge is 2400 MHz for 2.4 GHz band transmitter. For the higher band edge the EUT is set to transmit as follows: For a WLAN transmitter working in the 2.4 GHz band on highest channel: CH11 = 2462 MHz or CH13 = 2472 MHz / CH11= 2462 MHz for a channel bandwidth of 20 / 40 MHz. The higher band edge is 2483.5 MHz for a 2.4 GHz band transmitter. Analyzer settings for conducted measurement: - Detector: Peak - RBW / VBW = 100 / 300 kHz 2. Showing compliance of the higher band edge falls in to restricted bands by a radiated measurement. The radiated emissions measurements are performed in a typical installation configuration inside the fully anechoic chamber using a horn antenna at 1 m distance. EMI receiver settings for radiated measurement: - Detector: Peak, Average - IF Bandwidth = 1 MHz 3.2.2 Test Requirements / Limits FCC Part 15.247 (d) “In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. ... If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in Section 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)).” Test report Reference: MDE_DATA_1408_FCCe Page 20 of 31

For the conducted measurement the RF power at the band edge shall be “at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power...” For the radiated measurement of the higher band edge connected to a restricted band the limit is “specified in Section 15.209(a)”. 3.2.3 Test Protocol 3.2.3.1 Radiated measurement, higher band edge Temperature: 23–27 °C Air Pressure: 997-1011 hPa Humidity: 33–50 % WLAN b-Mode; 20 MHz; 1 Mbit/s Channel Center Spurious Limit Ch. Frequency Frequency Level RBW [dBµV/m Margin to Limit No. [MHz] [MHz] [dBm] Detector [kHz] ] [dB] Joya X2 Variant “BASIC” 11 2462 2483.5 50.7 PEAK 1000 74.0 23.3 11 2462 2483.5 39.8 AV 1000 54.0 14.2 Joya X2 Variant “PLUS” 11 2462 2483.5 50.5 PEAK 1000 74.0 23.5 11 2462 2483.5 39.3 AV 1000 54.0 14.7 WLAN g-Mode; 20 MHz; 6 Mbit/s Channel Center Spurious Ch. Frequency Frequency Level RBW Limit Margin to Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Joya X2 Variant “BASIC” 11 2462 2483.5 64.5 PEAK 1000 74.0 9.5 11 2462 2483.5 47.9 AV 1000 54.0 6.1 Joya X2 Variant “PLUS” 11 2462 2483.5 60.8 PEAK 1000 74.0 13.2 11 2462 2483.5 44.8 AV 1000 54.0 9.2 Test report Reference: MDE_DATA_1408_FCCe Page 21 of 31

3.2.3.2 Measurement Plot (showing the highest value, “worst case”) Marker: 2.4835 GHz 64.52 dBµV/m Delta Mk: 0 Hz -16.66 dB Level [dBµV/m] 80 70 60 50 40 30 20 10 0 2.48G 2.485G 2.49G 2.495G 2.5G Frequency [Hz] MES DAT_1408_041_pre PK MES DAT_1408_041_pre AV LIM FCC 15.209 3m Field Strength AV Limit LIM FCC 15.209 3m Peak Field Strength Q-Peak Limit WLAN mode g variant “BASIC” Test report Reference: MDE_DATA_1408_FCCe Page 22 of 31

4 Test Equipment List of Used Test Equipment The calibration, hardware and software states are shown for the testing period. Test Equipment Anechoic Chamber Lab ID: Lab 2 Manufacturer: Frankonia Description: Anechoic Chamber for radiated testing Type: 10.58x6.38x6.00 m³ Calibration Details Last Execution Next Exec. NSA (FCC) 2014/01/09 2017/01/09 Single Devices for Anechoic Chamber Single Device Name Type Serial Number Manufacturer Air compressor none - Atlas Copco Anechoic Chamber 10.58 x 6.38 x 6.00 m³ none Frankonia Calibration Details Last Execution Next Exec. FCC listing 96716 3m Part15/18 2014/01/09 2017/01/08 Controller Maturo MCU 961208 Maturo GmbH EMC camera CE-CAM/1 - CE-SYS EMC camera Nr.2 CCD-400E 0005033 Mitsubishi Filter ISDN B84312-C110-E1 Siemens&Matsushita Filter Universal 1A BB4312-C30-H3 - Siemens&Matsushita Test Equipment Auxiliary Equipment for Conducted emissions Lab ID: Lab 1 Manufacturer: Rohde & Schwarz GmbH & Co.KG Description: EMI Conducted Auxiliary Equipment Single Devices for Auxiliary Equipment for Conducted emissions Single Device Name Type Serial Number Manufacturer AC Power Source Chroma 6404 64040001304 Chroma ATE INC. Cable "LISN to ESI" RG214 W18.03+W48.03 Huber&Suhner Impedance Stabilization ISN T800 36159 Teseq GmbH Network Calibration Details Last Execution Next Exec. Standard Calibration 2014/02/06 2016/02/28 Impedance Stabilization ISN/CDN ENY41 100002 Rohde & Schwarz GmbH & Co. Network, Coupling KG Decoupling Network Calibration Details Last Execution Next Exec. Standard calibration 2013/03/01 2015/03/31 Impedance Stabilization ISN/CDN ST08 36292 Teseq GmbH Network, Coupling Decoupling Network Calibration Details Last Execution Next Exec. Standard calibration 2014/01/10 2016/01/31 Test report Reference: MDE_DATA_1408_FCCe Page 23 of 31

Single Devices for Auxiliary Equipment for Conducted emissions (continued) Single Device Name Type Serial Number Manufacturer Impedance Stabilization ISN/CDN T8-Cat6 32187 Teseq GmbH Network, Coupling Decoupling Network Calibration Details Last Execution Next Exec. Standard Calibration 2014/01/08 2016/01/31 One-Line V-Network ESH 3-Z6 100489 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. standard calibration 2014/06/18 2017/11/30 One-Line V-Network ESH 3-Z6 100570 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2013/11/25 2016/11/24 Two-Line V-Network ESH 3-Z5 828304/029 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standart Calibration 2013/03/01 2015/02/28 Two-Line V-Network ESH 3-Z5 829996/002 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2013/03/01 2015/02/28 Test report Reference: MDE_DATA_1408_FCCe Page 24 of 31

Test Equipment Auxiliary Equipment for Radiated emissions Lab ID: Lab 2 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Auxiliary Equipment for Radiated emissions Single Device Name Type Serial Number Manufacturer Antenna mast AM 4.0 AM4.0/180/119205 Maturo GmbH 13 Biconical dipole VUBA 9117 9117-108 Schwarzbeck Calibration Details Last Execution Next Exec. Standard Calibration 2012/01/18 2015/01/17 Broadband Amplifier JS4-18002600-32-5P 849785 Miteq 18MHz-26GHz Broadband Amplifier AFS4-01000400-1Q-10P-4 - Miteq 1GHz-4GHz Broadband Amplifier JS4-00101800-35-5P 896037 Miteq 30MHz-18GHz Cable "ESI to EMI EcoFlex10 W18.01-2+W38.01- Kabel Kusch Antenna" 2 Cable "ESI to Horn UFB311A+UFB293C W18.02-2+W38.02- Rosenberger Micro-Coax Antenna" 2 Double-ridged horn HF 906 357357/001 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/05/18 2015/05/17 Double-ridged horn HF 906 357357/002 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/06/26 2015/06/25 High Pass Filter 4HC1600/12750-1.5-KK 9942011 Trilithic High Pass Filter 5HC2700/12750-1.5-KK 9942012 Trilithic High Pass Filter 5HC3500/12750-1.2-KK 200035008 Trilithic High Pass Filter WHKX 7.0/18G-8SS 09 Wainwright Horn Antenna BBHA 9170 Schwarzbeck 15-26 GHz BBHA 9170 Log.-per. Antenna HL 562 Ultralog 100609 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/12/18 2015/12/17 Log.-per. Antenna HL 562 Ultralog 830547/003 Rohde & Schwarz GmbH & Co. KG Loop Antenna HFH2-Z2 829324/006 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2011/10/27 2014/10/26 Pyramidal Horn Antenna 3160-09 00083069 EMCO Elektronik GmbH 26,5 GHz Pyramidal Horn Antenna 3160-10 00086675 EMCO Elektronik GmbH 40 GHz Test report Reference: MDE_DATA_1408_FCCe Page 25 of 31

Single Devices for Auxiliary Equipment for Radiated emissions (continued) Single Device Name Type Serial Number Manufacturer Tilt device Maturo Antrieb TD1.5-10kg TD1.5- Maturo GmbH (Rohacell) 10kg/024/3790709 Test Equipment Auxiliary Test Equipment Lab ID: Lab 2, Lab 3 Manufacturer: see single devices Description: Single Devices for various Test Equipment Type: various Serial Number: none Single Devices for Auxiliary Test Equipment Single Device Name Type Serial Number Manufacturer AC Power Source Chroma 6404 64040001304 Chroma ATE INC. Broadband Power Divider 1506A / 93459 LM390 Weinschel Associates N (Aux) Broadband Power Divider WA1515 A855 Weinschel Associates SMA Digital Multimeter 03 Fluke 177 86670383 Fluke Europe B.V. (Multimeter) Calibration Details Last Execution Next Exec. Customized calibration 2013/12/04 2015/12/03 Fibre optic link Satellite FO RS232 Link 181-018 Pontis (Aux) Fibre optic link FO RS232 Link 182-018 Pontis Transceiver (Aux) Isolating Transformer LTS 604 1888 Thalheimer Transformatorenwerke GmbH Notch Filter Ultra Stable WRCA800/960-6EEK 24 Wainwright (Aux) Signal Analyzer FSV30 103005 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard 2014/02/10 2016/02/09 Spectrum Analyser FSP3 836722/011 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard 2012/06/13 2015/06/12 Spectrum Analyser FSU26 200418 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2013/07/29 2014/07/28 Vector Signal Generator SMIQ 03B 832492/061 Rohde & Schwarz GmbH & Co.KG Test report Reference: MDE_DATA_1408_FCCe Page 26 of 31

Test Equipment Digital Signalling Devices Lab ID: Lab 1, Lab 2, Lab 3 Description: Signalling equipment for various wireless technologies. Single Devices for Digital Signalling Devices Single Device Name Type Serial Number Manufacturer Bluetooth Signalling Unit CBT 100589 Rohde & Schwarz GmbH & Co. CBT KG Calibration Details Last Execution Next Exec. Standard calibration 2011/11/24 2014/11/23 CMW500 CMW500 107500 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/01/27 2016/01/26 Digital Radio CMD 55 831050/020 Rohde & Schwarz GmbH & Co. Communication Tester KG Calibration Details Last Execution Next Exec. Standard calibration 2011/11/28 2014/11/27 Universal Radio CMU 200 102366 Rohde & Schwarz GmbH & Co. Communication Tester KG HW/SW Status Date of Start Date of End Hardware: 2007/07/16 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B56V14, B68 3v04, PCMCIA, U65V04 Software: K21 4v21, K22 4v21, K23 4v21, K24 4v21, K42 4v21, K43 4v21, K53 4v21, K56 4v22, K57 4v22, K58 4v22, K59 4v22, K61 4v22, K62 4v22, K63 4v22, K64 4v22, K65 4v22, K66 4v22, K67 4v22, K68 4v22, K69 4v22 Firmware: µP1 8v50 02.05.06 --- Universal Radio CMU 200 837983/052 Rohde & Schwarz GmbH & Co. Communication Tester KG Calibration Details Last Execution Next Exec. Standard calibration 2011/12/07 2014/12/06 HW/SW Status Date of Start Date of End HW options: 2007/01/02 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B54V14, B56V14, B68 3v04, B95, PCMCIA, U65V02 SW options: K21 4v11, K22 4v11, K23 4v11, K24 4v11, K27 4v10, K28 4v10, K42 4v11, K43 4v11, K53 4v10, K65 4v10, K66 4v10, K68 4v10, Firmware: µP1 8v40 01.12.05 --- SW: 2008/11/03 K62, K69 Vector Signal Generator SMU200A 100912 Rohde & Schwarz GmbH & Co. KG Test report Reference: MDE_DATA_1408_FCCe Page 27 of 31

Test Equipment Emission measurement devices Lab ID: Lab 1, Lab 2 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Emission measurement devices Single Device Name Type Serial Number Manufacturer Personal Computer Dell 30304832059 Dell Power Meter NRVD 828110/016 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/05/13 2015/05/12 Sensor Head A NRV-Z1 827753/005 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/05/13 2015/05/12 Signal Generator SMR 20 846834/008 Rohde & Schwarz GmbH & Co. KG Spectrum Analyzer ESIB 26 830482/004 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2014/01/07 2016/01/31 HW/SW Status Date of Start Date of End Firmware-Update 4.34.4 from 3.45 during calibration 2009/12/03 Test Equipment Multimeter 12 Lab ID: Lab 4, Lab 5 Description: Ex-Tech 520 Serial Number: 05157876 Single Devices for Multimeter 12 Single Device Name Type Serial Number Manufacturer Digital Multimeter 12 EX520 05157876 Extech Instruments Corp. (Multimeter) Calibration Details Last Execution Next Exec. Customized calibration 2013/12/04 2015/12/03 Test report Reference: MDE_DATA_1408_FCCe Page 28 of 31

Test Equipment T/A Logger 13 Lab ID: Lab 1, Lab 2, Lab 3 Description: Lufft Opus10 TPR Type: Opus10 TPR Serial Number: 13936 Single Devices for T/A Logger 13 Single Device Name Type Serial Number Manufacturer ThermoAirpressure Opus10 TPR (8253.00) 13936 Lufft Mess- und Regeltechnik Datalogger 13 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/02/07 2015/02/06 Test Equipment T/H Logger 02 Lab ID: Lab 1 Description: Lufft Opus10 Serial Number: 7489 Single Devices for T/H Logger 02 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 7489 Lufft Mess- und Regeltechnik 02 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/02/07 2015/02/06 Test Equipment T/H Logger 03 Lab ID: Lab 3 Description: Lufft Opus10 Serial Number: 7482 Single Devices for T/H Logger 03 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 7482 Lufft Mess- und Regeltechnik 03 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/02/07 2015/02/06 Test Equipment T/H Logger 12 Lab ID: Lab 2 Description: Lufft Opus10 Serial Number: 12482 Single Devices for T/H Logger 12 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 12482 Lufft Mess- und Regeltechnik 12 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/01/07 2015/01/06 Test report Reference: MDE_DATA_1408_FCCe Page 29 of 31

Test Equipment T/H Logger 15 Lab ID: Lab 4, Lab 5 Description: Lufft Opus10 Serial Number: 13985 Single Devices for T/H Logger 15 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 13985 Lufft Mess- und Regeltechnik 15 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/01/07 2015/01/06 Test report Reference: MDE_DATA_1408_FCCe Page 30 of 31

5 Photo Report Please refer to external report. 6 Setup Drawings Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting groundplane. Test report Reference: MDE_DATA_1408_FCCe Page 31 of 31


Document Created: 2019-10-05 05:06:22
Document Modified: 2019-10-05 05:06:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC