5GHz report JNG B GUN radiated

FCC ID: U4GJNGW

Test Report

Download: PDF
FCCID_3211621

PARTIAL TEST REPORT No.: 2-20842790-15-8b According to: FCC Regulations Part 15.407, Part 15.207 IC-Regulations RSS-Gen, Issue 4 RSS-247, Issue 1 for Datalogic ADC S.r.l. JOYA TOUCH Type:B00AN00HL0GT0W7-GRR FCC-ID: U4GJNGW IC: 3862E-JNGW PMN: JOYA TOUCH HVIN: JNG B GUN Laboratory Accreditation and Listings Voluntary Controls for Industry Canada Electromagnetic Emissions Reg. No.: 3462D-2 Reg. No.: MRA US-EU 0003 Reg. No.: 3462D-3 R-2666 C-2914, T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 32 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 2-20842790-15-8b, Page 2 of 32 Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. Tests measurement overview according of US CFR Title 47, Subpart 15C and Canada RSS-Standards: ...... 3 1.2. Attestation:....................................................................................................................................................... 4 2. ADMINISTRATIVE DATA ............................................................................................................................... 5 2.1. Identification of the testing laboratory ............................................................................................................. 5 2.2. Test location .................................................................................................................................................... 5 2.3. Organizational items ........................................................................................................................................ 5 2.4. Applicant’s details ........................................................................................................................................... 5 2.5. Manufacturer’s details ..................................................................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 6 3.1. Technical 5GHz W-LAN data of main EUT declared by applicant ................................................................ 6 3.2. IEEE 802.11 OVERVIEW: MODULATION AND DATA RATES .............................................................. 7 3.3. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 7 3.4. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 7 3.5. EUT set-ups ..................................................................................................................................................... 7 3.6. EUT operating modes ...................................................................................................................................... 8 3.7. EUT power level configurations ...................................................................................................................... 8 3.8. Configuration of cables used for testing .......................................................................................................... 8 4. DESCRIPTION OF TEST SYSTEM SET-UP’S .............................................................................................. 9 4.1. Test system set-up for conducted measurements on antenna port ................................................................... 9 4.2. Test system set-up for radiated magnetic field measurements below 30 MHz ................................................ 11 4.3. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz ............................................... 12 4.4. Test system set-up for radiated electric field measurement above 1 GHz ....................................................... 13 5. MEASUREMENTS ............................................................................................................................................. 14 5.1. Duty-Cycle....................................................................................................................................................... 14 5.2. RF-Parameter - Transmitter Peak output power (conducted and radiated) ...................................................... 15 5.3. RF-Parameter - Power Spectral Density .......................................................................................................... 17 5.4. General Limit - Radiated field strength emissions below 30 MHz .................................................................. 19 5.5. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz .............................................................. 21 5.6. General Limit - Radiated emissions, above 1 GHz .......................................................................................... 23 5.7. General Limit - Band-edge compliance measurements ................................................................................... 25 5.8. Measurement uncertainties .............................................................................................................................. 27 6. ABBREVIATIONS USED IN THIS REPORT ................................................................................................. 28 7. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 28 8. INSTRUMENTS AND ANCILLARY ................................................................................................................ 29 8.1. Used equipment “CTC” ................................................................................................................................ 29 9. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ............................................................................. 32 Table of annex The listed attachments are an integral part of this report Total pages Annex 1: Test result diagrams (separate document) TR2-20842790-15-8b-A1 77 Annex 2: External photographs of EUT (separate document) TR2-20842790-15-8b-A2 6 Annex 3: Internal photographs of EUT (separate document) TR2-20842790-15-8b-A3 12 Annex 4: Test set-up photographs (separate document) TR2-20842790-15-8b-A4 12 Tune-up procedure for SSD45_JOYA TOUCH Basic_rev20160621 (supplied by applicant) 2 JOYANG_TEST-TOOLS_QUICK_START_INSTRUCTIONS_REV20160530 (supplied by applicant) 41 JOYANG_ WLAN Antenna Final Report (22-Feb-2016) (supplied by applicant) 11 Operational Description_JOYA TOUCH_20160530_rev05 (supplied by applicant) 10 TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 3 of 32 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. Also we refer on special conditions which the applicant should fulfill according §2.927 to §2.948, special focus regarding modification of the equipment and availability of sample equipment for market surveillance tests. The presented Equipment Under Test (in this report, hereinafter referred as EUT) supports radiofrequency technologies with WLAN technology and operating frequency range at 5150 to 5850 GHz according to IEEE 802.11 a/ac. Other implemented wireless technologies were not considered within this test report. The build-in W-LAN module is already approved with FCC ID: SQG-SSD45N and IC:3147A-SSD45N. Following test cases have been performed to show compliance with valid Part 15.209/15.407 of the FCC CFR Title 47 Rules, Edition 4th November 2015 and IC RSS-247 Issue 1/RSS-Gen Issue 4 standards. 1.1. Tests measurement overview according of US CFR Title 47, Subpart 15C and Canada RSS-Standards: References and Limits EUT EUT Test cases Port FCC RSS- op. Result Test limit set-up Standard Standard mode TX-Mode Antenna 99% occupied RSS-Gen, terminal 2.1049(h) 99% Power bandwidth -- -- Remark 1.) bandwidth Issue 4 (conducted) No pass/fail criteria Antenna To be reported accord. Duty-Cycle terminal -- -- 2 1 Remark 4.) KDB789033 or ANSI (conducted) C63.10:2013 RSS-247, (1) lesser of 200mW or Issue 1 10dBm+10logB Antenna chapter Maximum §15.407(a) (2): lesser of 250mW or Pass terminal 6.2.1(1) 2 1 output power (1)(2)(3) 11dBm+10logB Remark 4.) (conducted) 6.2.2(1) (3): lesser of 250mW or 6.2.3(1) 11dBm+10logB 6.2.4(1) RSS-247, Issue 1 Antenna chapter (1): 10dBm/MHz Peak Power §15.407(a) Pass terminal 6.2.1(1) (2): 11dBm/MHz 2 1 Spectral density (1)(2)(3) Remark 4.) (conducted) 6.2.2(1) (3): 11dBm/MHz 6.2.3(1) 6.2.4(1) RSS-247, Issue 1 Antenna chapter See Antenna gain §15.407(a) < 6dBi or reduction of terminal 6.2.1(1) -- -- Applicant’s information (1)(2)(3) power/power density (conducted) 6.2.2(1) declaration 6.2.3(1) 6.2.4(1) TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 4 of 32 General field Enclosure + FCC/IC: Emissions in strength §15.407(6) emissions Inter- §15.407(b) restricted bands must meet connecting the general field-strength 1 1 Pass within §15.205 RSS-247, cables radiated limits restricted §15.209 Issue 1 (radiated) IC: Chapter 8.9 Table 4+5+6 bands chapter 6.2.1(2) Emissions in restricted bands §15.205 6.2.2(2) must meet the general field- 1 1 Pass §15.209 6.2.3(2) strength radiated limits Enclosure + 6.2.4(2) chapter 8.9 Table 6 Band-Edge Inter- Out-of-band emission EIRP compliance connecting < -27dBm/MHz or radiated cables RSS-Gen., -17dBm/MHz (radiated) §15.407(b) Issue 4 1 1 Pass If applicable (EIRP>200mW): Elevation Mask of radiation pattern IC: A9.3 Dynamic Antenna RSS-247, (a) General frequency terminal §15.407 Issue 1 -- -- Remark 2.) (b) Operational requirements selection (DFS) (conducted) chapter 6.3 -- AC-Power FCC §15.107 RSS-Gen, Lines class B limits AC-Power Issue 4: §15.207 §15.207 limits -- -- Remark 3.) lines Chapter 8.8, Conducted Table 3 Emissions IC: Table 3 Remark: 1.) Please refer integrated SSD45N W-LAN Module’s reports FCC ID: SQG-SSD45N Report No.FR442904-01AN Version Rev.01, issued Sep. 15, 2015 Report No.FR442904-01AI Version Rev.01, issued Sep. 15, 2015 IC:3147A-SSD45N Report No.CR442904-02AN Version Rev.01, issued Nov. 03, 2015 2.) Please refer separate Report No.1-1858_16-02-03 issued on 25.05.2016 3.) Please refer separate test report TR2-20842790-15-10d, performed on EUT with FCC-ID: U4GJNGWB and IC: 3862E-JNGWB due to same charging circuit design – see applicants documents 4.) Conducted Tests performed only on Worst-Case JOYA TOUCH Variant Type: P00AN04HL0GT0W7-GRR (see test report TR2-20842790-15-10b) RF-Exposure Evaluation (separation distance user to RF-radiating element greater 20cm) References & Limits EUT EUT opera- Test cases Port FCC Result RSS Section Test Limit set-up ting Standard mode RF-Field Cabinet Strength Limits: Radio + FCC: “general See separate frequency §1.1310(b) Inter- RSS-102 population/ test report radiation §2.1091 1 1 connecting Issue 5 uncontrolled” 1-1858_16- exposure §2.1093 01-04 cables environment requirements (radiated) Table 1 IC: Table 4 1.2. Attestation: I declare that all measurements were performed by me or under my supervision and that all measurements have been performed and are correct to my best knowledge and belief to Industry Canada standards. All requirements as shown in above table are met in accordance with enumerated standards. Digitally signed by christian. lorenz@cetecom.com DN: cn=christian. lorenz@cetecom.com Date: 2016.10.31 11:17:12 +01'00' ...................................................... .................................................... Dipl.-Ing. Rachid Acharkaoui Dipl:-Ing. Christian Lorenz Responsible for test section Responsible for test report TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 5 of 32 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Rachid Acharkaoui Deputy: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report : Dipl:-Ing. Christian Lorenz Project leader: Dipl.-Ing. V. Krueger Receipt of EUT: 2016-02-29 Date(s) of test: 2016-03-02 to 2016-10-10 Date of report: 2016-10-12 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 13.02 2.4. Applicant’s details Applicant’s name: Datalogic ADC S.r.l. Address: Via S. Vitalino, 13 40012, Lippo di Calderara di Reno (BO) ITALY Contact person: Mr. Eucarpio Guarisco 2.5. Manufacturer’s details Manufacturer’s name: please see Applicant's details Address: please see Applicant's details TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 6 of 32 3. Equipment under test (EUT) 3.1. Technical 5GHz W-LAN data of main EUT declared by applicant U-NII 1  Ch. 36 to Ch. 48 (Nominal 20MHz signal bandwidth) (5150-5250MHz)  Ch. 38 to Ch. 46 (Nominal 40MHz signal bandwidth) U-NII2A  Ch. 52 to Ch. 64 (Nominal 20MHz signal bandwidth) Frequency range (5250-5350MHz)  Ch. 54 to Ch. 62 (Nominal 40MHz signal bandwidth) and channels U-NII 2C  Ch. 100 to 140 (Nominal 20MHz signal bandwidth) (5470-5725MHz)  Ch. 102 to 134 (Nominal 40MHz signal bandwidth)  Ch. 149 to 165 (Nominal 20MHz signal bandwidth) U-NII-3  Ch. 151 to 159 (Nominal 40MHz signal bandwidth)  BPSK  QPSK Type of modulation (packet types)  16-QAM  64-QAM  256-QAM  20MHz bandwidth: 36/40/44/48/52/56/60/64/100/104/108/112/116 Number of channels 132/136/138/140/149/153/157/161/165 (USA/Canada -bands)  40MHz bandwidth: 38/46/54/62/102/110/118/134/151/159  Integrated Antenna Type  External, no RF- connector  External, separate RF-connector According to Applicant’s declaration 5150 to 5250 MHz: 5.88 dBi Antenna Gain 5250 to 5350 MHz: 5.88 dBi 5470 to 5700 MHz: 5.88 dBi 5725 to 5850 MHz: 5.88 dBi  W-LAN 2.4 GHz(not tested within this test report)  Bluetooth©(not tested within this test report) Installed options  NFC (not tested within this test report)  battery charging option (WPC) (not tested within this test report)  Internal battery Li-Io 3.41V DC to 4.35 V DC (nominal 3.75 V DC) Power supply  over AC/DC adapter: 120V/60 Hz  DC power only: Special EMI components -- EUT sample type  Production  Pre-Production  Engineering Firmware  for normal use  Special version for test execution FCC label attached  yes  no Please refer Applicants declaration for further details TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 7 of 32 3.2. IEEE 802.11 OVERVIEW: MODULATION AND DATA RATES The modulations and data rates defined for 802.11 a/n transmitters are identified in the table below. Also it shows which operational mode is possible for the device under test (EUT) according applicant’s information. 802.11a-Mode (OFDM system) Brutto data rate [MBps] Modulation type of subcarriers Supported by EUT 6/9 BPSK Yes 12 /18 QPSK Yes 24 / 36 16-QAM Yes 48 / 54 64-QAM Yes Remark: 52 sub-carriers which can be modulated at different data-rates. 802.11n-Mode (OFDM) Brutto data rate [MBps] Modulation type Supported by EUT 7.2/14.4/21.7/28.9/43.3/57.8/65/72.2 Mbps HT20 (MCS0..MCS7) Yes 14.444/28.889/43.333/57.778/86.667/ HT20 (MCS8..MCS15) No 115.556/130/144.444 Mbps 15/30/45/60/90/120/135/150 Mbps HT40 (MCS0..MCS7) No 30/60 Mbps HT40 (MCS8..MCS9) No 90/120/180/240/270/300 Mbps HT40 (MCS10..MCS15) No 3.3. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial number hardware status software status tion*) SW Beta HW B00AN00HL0GT0 Version:WEC7 EUT A JOYA TOUCH Z16P00218 Version W7-GRR Firmware P/N: 911350024 Version: 2.16 *) EUT short description is used to simplify the identification of the EUT in this test report 3.4. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE short S/N HW SW descrip- Auxiliary Equipment Type serial number hardware status software status tion *) AE 1 -- -- -- -- -- *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. 3.5. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) set. 1 EUT A Radiated measurements Set-up set. 2 EUT A + Cable 1 Conducted measurements Set-up *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 8 of 32 3.6. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) With help of installed Datalogic test firmware version 2.16 a continuous TX- a/n (HT20) Mode can be established on op. 1 TX- Mode -desired channels, modulation data rates in LRU Application -maximum 90% power level in LMU application. *) EUT operating mode no. is used to simplify the test report. 3.7. EUT power level configurations EUT Description of operating Power level information operating modes mode no.*) With help of installed Datalogic test firmware version 2.16 maximum 90% power level in LMU application is configured for all measurements included in this report. op. 1 TX- Mode This Power level will now be considered as a Nominal Power level throughout this report & shall be used for compliance purposes. 3.8. Configuration of cables used for testing Cable S/N HW Cable length number Item Type serial number hardware status Cable 1 RF –SMA Cable -- -- -- -- TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 9 of 32 4. Description of test system set-up’s 4.1. Test system set-up for conducted measurements on antenna port Conducted Set-up W1 W-LAN conducted RF-Setup 1 (W1 Set-up) General description: The EUT‘s RF-signal is coupled out by a suitable antenna coupling connector (1). The signal is first attenuated (2) then connected to the power meter (3) for conducted power measurements. The specific attenuation loss is determined prior to the measurement within a set-up attenuation measurement. These are then taken into account by correcting the measurement readings. Schematic: Testing method: ANSI C63.10: 2013 Chapter 12.3.3.1+ FCC KDB 789033v01r03 Used Equipment Passive Elements Test Equipment Remark:  20 dB Attenuator  Power Meter See List of equipment under each test  Low loss RF-  DC-Power Supply case and chapter 8 for calibration info cables  Spectrum-Analyser Measurement uncertainty See chapter 5.8 TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 10 of 32 Conducted Set-up W2 W-LAN conducted RF-Setup 2 (W2 Set-up) General description: The EUT‘s RF-signal is coupled out by a suitable antenna coupling connector (1). The signal is first attenuated (2) then connected to spectrum-analyzer (4) for RF-conducted measurements. The specific attenuation loss is determined prior to the measurement within a set-up attenuation measurement. These are then taken into account by correcting the measurement readings of the spectrum-analyzer. Schematic: Testing method: ANSI C63.10:2013, FCC KDB 789033v01r03 Used Equipment Passive Elements Test Equipment Remark:  20 dB Attenuator  Power Meter See List of equipment under each test  Low loss RF-  DC-Power Supply case and chapter 8 for calibration info cables  Spectrum-Analyser Measurement uncertainty See chapter 5.8 Testing method for DTS- ANSI C63.10: 2013 Chapter 11.9.2.3.1+ FCC KDB 789033v01r03 devices: TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 11 of 32 4.2. Test system set-up for radiated magnetic field measurements below 30 MHz Specification: ANSI C63.10-2013 chapter 6.4 (§6.4.4.2) General Description: Evaluating the radiated field emissions are done first by an exploratory emission measurement and a final measurement for most critical frequencies determined. The loop antenna was placed at 1 m height above ground plane and 3 m measurement distance from set-up for investigations. Because of reduced measurement distance, correction data were applied, as stated in chapter “General Limit - Radiated field strength emissions below 30 MHz“. The tests are performed in the semi anechoic room recognized by the regulatory commission. Schematic: Testing method: Exploratory, preliminary measurement Final measurement on critical frequencies The EUT and it’s associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 0.8 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (step cable position, etc. 90°, range 0°to 360°) and the EUT itself either on 3-orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT), the emission spectrum was recorded. The precisely. After this step, for all identified critical loop antenna was moved at least to frequencies, the maximum peak was determined. 2-perpendicular axes (antenna vector in direction of EUT and parallel to EUT) in order to maximize Following parameters were varied: the turntable the emissions. The results are documented in a angle continuously in the range 0 to 360 degree, diagram. Critical frequencies (low margin to the EUT itself either over 3-orthogonal axis (not limit) are saved within a data reduction table for defined usage position) or 2-orthogonal axis further investigations. If various operating modes (defined usage position). are supported, further investigations are made to find the worst-case. Also the interconnection On the determined worst-case position, a final cables and equipment position were varied in measurement with necessary bandwidth and order to maximize the emissions. detector according standard has been carried out. Formula: EC = ER + AF + CL + DF - GA AF =Antenna factor CL = Cable loss M = LT-EC DF= Distance correction factor EC = Electrical field – corrected value ER = Receiver reading GA= Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. Distance correction: Reference for applied correction (extrapolating) factors due to reduced measurement distance: ANSI C63.10:2013, §6.4.4.2 - Equations (2) + (3) + (4) TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 12 of 32 4.3. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz Specification: ANSI C63.4-2014 chapter 8.2.3, ANSI C63.10-2013 chapter 6.5 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a NSA-compliant semi anechoic room (SAR) recognized by the regulatory commissions. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are placed Based on the exploratory measurements, the most on a non-conductive position manipulator (tipping critical frequencies are re-measured by main- device) of 0.8 m height which is placed on the taining the EUT’s worst-case operation mode, cable turntable. By rotating the turntable (range 0° to position, etc. either on 10m OATS or 3m semi- 360°, step 90°) and the EUT itself either on 3- anechoic room. orthogonal axis (portable equipment) or 2- orthogonal axis (defined operational position of First a frequency zoom around the critical frequency EUT) the emission spectrum and it’s is done to locate the frequency more precisely. After characteristics was recorded with an EMI- this step, for all identified critical frequencies, the receiver, broadband antenna and software. maximum peak was determined. Measurement antenna: horizontal and vertical, Following parameters were varied: the turntable heights: 1,0 m and 1,82 m as worst-case angle continuously in the range 0 to 360 degree, the determined by an exploratory emission EUT itself either over 3-orthogonal axis (not measurements. The results are documented in a defined usage position) or 2-orthogonal axis diagram. Critical frequencies (low margin to (defined usage position). The measurement antenna limit) are saved within a table for further height between 1 m and 4 m. investigations. If various operating modes are supported, further investigations are made to find On the determined worst-case position, a final the worst-case of them. Also the interconnection measurement with necessary bandwidth and cables and equipment position were varied in detector according standard has been carried out. order to maximize the emissions. Formula: EC = ER + AF + CL + DF - GA (1) AF = Antenna factor CL = Cable loss M = LT - EC (2) DF = Distance correction factor (if used) EC = Electrical field – corrected value ER = Receiver reading GA = Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 13 of 32 4.4. Test system set-up for radiated electric field measurement above 1 GHz Specification: ANSI C63.4-2014 chapter 8.3, ANSI C63.10-2013 chapter 6.6.3.3 & 6.6.4 General Description: Evaluating the emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a CISPR 16-1-4:2010 compliant fully anechoic room (FAR) recognized by the regulatory commission. The measurement distance was set to 3 meter for frequencies up to 18 GHz and 2 meter above 18 GHz. A logarithmic periodic antenna is used for the frequency range 30 MHz to 1 GHz. Horn antennas are used for frequency range 1 GHz to 40 GHz. The EUT is aligned within 3 dB beam width of the measurement antenna with three orthogonal axis measurements on the EUT. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are placed Based on the exploratory measurements, the most on a non-conductive position manipulator (tipping critical frequencies are re-measured by main- device) of 1.55 m height which is placed on the taining the EUT’s worst-case operation mode, turntable. By rotating the turntable (range 0° to cable position, etc. 360°, step 15°) and the EUT itself either on 3- orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT) the emission spectrum and it’s precisely. After this step, for all identified critical characteristics was recorded with an EMI- frequencies, the maximum peak was determined. receiver, broadband antenna and software. Following parameters were varied: the turntable The measurements are performed in horizontal angle continuously in the range 0 to 360 degree, and vertical polarization of the measurement the EUT itself over 3-orthogonal axis and the antennas. The results are documented in a height for EUT with large dimensions. diagram. Critical frequencies (low margin to limit) are saved within a table for further On the determined worst-case position, a final investigations. If various operating modes are measurement with necessary bandwidth and supported, further investigations are made to find detector according standard has been carried out. the worst-case of them. Also the interconnection On the determined worst-case position, a final cables and equipment position were varied in measurement with necessary bandwidth and order to maximize the emissions. detector according standard has been carried out. Formula: EC = ER + AF + CL + DF - GA (1) EC = Electrical field – corrected value ER = Receiver reading M = LT - EC (2) M = Margin LT = Limit AF = Antenna factor CL = Cable loss DF = Distance correction factor (if used) GA = Gain of pre-amplifier (if used) All units are dB-units, positive margin means value is below limit. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 14 of 32 5. Measurements 5.1. Duty-Cycle 5.1.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') Ambient Climatic conditions Temperature: (22±2)°C Rel. humidity: (45±15)% test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  equipment  331 HC 4055      spectr. analys.  683 FSU26  120 FSEM  264 FSEK    power meter  262 NRV-S  266 NRV-Z31  265 NRV-Z33  261 NRV-Z55  356 NRV-Z1  multimeter  341 Fluke 112      DC power  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery  350 Car battery  463 HP3245A line voltage  230 V 50 Hz via public mains  4.35 V DC (fully charged internal battery) otherwise K4 Cable  530 Attenuator 10dB Method of measurement:  conducted  radiated A special firmware program is used for test purposes. In opposite to normal operating mode a higher duty-cycle is set in order to facilitate the measurements. This is maximized at the extent possible. The necessary duty-cycle correction factor is determined on nominal conditions on middle channel only. It is assumed that no noticeable changes occur when tested on other channels or climatic conditions. The Duty-Cycle was constant, means without variations. Minimum and maximum modulation index was tested, the duty cycle is to be found therefore between a minimum and maximum values. DUT Y-CYCLE M e asure me nt WLAN Marker 1 Marker 2 T X on T X off Correction- Channel 36 [RX ON] [BTS ON'] Converted to Factor: DC ms ms ms ms 100log(1/DC) (%) Modulation (dB) Results: Calculated with following formulas: Duty cycle: x Tx on 1 Duty cycle factor [dB]: 10 log  Tx on  Tx off x The results were corrected in order to evaluate for worst-case result each time when average values are necessary for example average radiated emissions or similar. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 15 of 32 5.2. RF-Parameter - Transmitter Peak output power (conducted and radiated) 5.2.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  443 System CTC-FAR-EMI-  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  489 ESU 40  620 ESU 26   otherwise  600 NRVD  357 NRV-Z1  693 TS8997 spectr. analys.  215 FSU  120 FSEM  264 FSEK    power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 6 dB Power 20dB otherwise  693 TS8997  248  529  - cable OTA20  613  K5 Cable Attenuator divider Attenuator line voltage  4.35 V DC (fully charged internal battery) 5.2.2. Reference: FCC  Part 15 Subpart C, §15.407(a)(1)(2)(3) IC  RSS-247, Issue 1 ANSI  C63.10-2013  789033 D02 General UNII test procedures v01r03: Subchapter E, Method PM (3)(a) KDB Guidance no.  U-NII 1: 5.15-5.25 GHz: FCC Outdoor access point: 1W + antenna gain max. 6dBi + Elevation > 30° 21 dBm EIRP FCC Indoor Access Point: 1W + antenna gain max. 6dBi FCC Mobile & Portable client: 250mW + antenna gain max. 6dBi IC: E.I.R.P. max. 200mW or 10+10log10(B) whichever power less  U-NII2: 5.25-5.35 GHz: FCC: 250mW or 11dBm+10log10(B) IC: 250mW or 11dBm+10log10(B) + EIRP Elevation Mask requirements if max. Limits EIRP>200mW Max. EIRP 1Watt or 17+10log10(B) whichever power less  U-NII2extension: 5.470-5.725 GHz: FCC/IC: Lesser of: 250mW or 11dBm+10log10(B) whichever power less Max. EIRP 1Watt or 17+10log10(B) whichever power less  U-NII3 : 5.475-5.85 GHz: FCC/IC: Max. EIRP 1Watt Remark: -- 5.2.3. Antenna characteristics: According §15.407(a)(1)(2):  directional gain < 6 dBi (measured: difference between measured conducted and radiated eirp. power)  directional gain > 6 dBi (measured / applicant’s declaration) -> conducted power reduction necessary  Maximum declared antenna gain [isotropic]: 5.88 dBi 5.2.4. EUT settings: The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. Different modulation characteristics have been checked, e.g. data rates which EUT can operate. Different frequencies within each operating band have been selected. 5.2.5. Measurement method: The power was also checked for different data rates, modulation scheme or packet types if applicable. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 16 of 32 5.2.6. Conducted power measurement and EIRP calculation Duty-Cycle Correction applicable according. to KDB 789033v01r03 Max. Peak Power (conducted) [dBm] Set-up no: 2 U-NII 1 U-NII-A U-NII2C U-NII-3 Op-Mode: 1 (5150-5250MHz) (5250-5350MHz) (5470-5725MHz) (5725-5825MHz) Measured Level 14.46 13.88 12.13 12.82 a-Mode Measured Level 14.46 13.74 12.15 12.77 n(HT20)-Mode Measured Max. Level 14.46 13.88 12.15 12.82 23.98 (Outdoor use 21.0 Conducted Limit [dBm]: dBm e.i.r.p. for azimuth angles 23.98 23.98 30.0 > 30° over horizon) Remark: 1.) Only maximum values among all data rates and modulations are given above. For other data rates please refer measurement table in separate annex A1 2.) Above values are inclusive Duty cycle correction factors. For further details please refer measurement table in separate annex A1 3.) Conducted Tests performed only on Worst-Case JOYA TOUCH Variant Type: P00AN04HL0GT0W7-GRR ( see test report TR2-20842790-15-10b ) 5.2.7. Verdict: Pass TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 17 of 32 5.3. RF-Parameter - Power Spectral Density 5.3.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  489 ESU  683 FSU26   spectr. analys.  489 ESU  120 FSEM  264 FSEK    power supply  463 HP3245A  457 EA 3013A  463  268 EA- 3050  494 AG6632A  498 NGPE 40  4.35 V DC (fully charged internal battery)  060 110 V 60 Hz via PAS 5000 otherwise 530 10dB Attenuator  cable K4 5.3.2. REFERENCES: §15.247(e), RSS-247, Chapter 5.2(2) (e) For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall be used to determine the power spectral density. 5.3.3. TEST CONDITION AND MEASUREMENT TEST SET-UP Signal ink to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% General measurement procedures Please see chapter “Test system set-up for conducted RF-measurement at antenna Port” (W2 Set-up) 5.3.4. EUT SETTINGS: The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. Different modulation characteristics have been checked, e.g. data rates which EUT can operate. 5.3.5. MEASUREMENT METHOD/ SPECTRUM-ANALYZER SETTINGS Measurement Method  ANSI 63.10:2009  PKPSD-Method  AVGPSD Method  FCC KDB 789033v01r03 Center Frequency Nominal channel frequency Span 5..30% higher than the EBW measured before Resolution Bandwidth (RBW) > 3 kHz (at least 3 times RBW) - pls. see diagram Video Bandwidth (VBW) > 10 kHz - pls. see diagram Sweep time coupled Detector Peak, Max hold mode for method PKPSD or RMS method AVGPSD Sweep Mode Repetitive mode, allow trace to stabilize (PKPSD) or single (AVGPSD) Addition of correction factors external measuring set-up path-loss Remarks:-- TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 18 of 32 5.3.6. RESULTS Power Spectral Density Test conditions Set-up no: 2 Op-Mode: 1 RBW Units dBm/1MHz dBm/500kHz U-NII 1 U-NII-A U-NII2C U-NII-3 Operating Bands (5150-5250MHz) (5250-5350MHz) (5470-5725MHz) (5725-5825MHz) Channel Number 36 40 48 52 56 64 100 116 140 149 157 165 Channel Frequency (MHz) 5180 5200 5240 5260 5280 5320 5500 5580 5700 5745 5785 5825 a-Mode 3.01 2.21 2.24 2.17 1.33 1.22 0.68 0.86 -0.32 -2.78 -1.78 -1.89 Measured Conducted (dBm) n(HT20)-Mode 2.65 2.68 2.37 1.99 1.95 1.02 0.45 0.43 -0.53 -2.83 -1.90 -2.05 Measured Conducted (dBm) Max. Conducted Value 3.01 2.17 0.86 -1.78 (dBm) Conducted Limits (dBm) 11 11 11 30 Antenna Gain (dBi) 5.88 5.88 5.88 5.88 Max. E.I.R.P. 8.89 8.05 6.74 4.10 Calculated(dBm) 11 + Limits (dBm) Antenna Gain 17 17 30 (< 6 dBi) Remarks: 1.) Measurements are performed only for modes with relevant data rates and modulations having maximum conducted power values among available a / n(HT20) modes, other data rates and modulations. For further details & other data rates please refer diagrams in separate annex A1 2.) Max. E.I.R.P. Calculated(dBm) = Max. Conducted Value (dBm) + Applicant’s declared Antenna Gain (dBi) 3.) Conducted Tests performed only on Worst-Case JOYA TOUCH Variant Type: P00AN04HL0GT0W7-GRR ( see test report TR2-20842790-15-10b ) 5.3.7. VERDICT: Pass TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 19 of 32 5.4. General Limit - Radiated field strength emissions below 30 MHz 5.4.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  347 Radio.lab.   receiver  377 ESCS30  001 ESS     spectr. analys.  584 FSU  120 FSEM  264 FSEK    antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix  378 RadiSense DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 line voltage  4.35 V DC (fully charged internal battery) 5.4.2. Requirements FCC Part 15, Subpart C, §15.205 & §15.209 IC RSS-Gen: Issue 4: §8.9 Table 5 ANSI C63.10-2013 Frequency Field strength limit Distance Remarks [MHz] [μV/m] [dBμV/m] [m] 0.009 – 0.490 2400/f (kHz) 67.6 – 20Log(f) (kHz) 300 Correction factor used due to measurement distance of 3 m 0.490 – 1.705 24000/f (kHz) 87.6 – 20Log(f) (kHz) 30 Correction factor used due to measurement distance of 3 m 1.705 – 30 30 29.5 30 Correction factor used due to measurement distance of 3 m 5.4.3. Test condition and test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)%  9 – 150 kHz RBW/VBW = 200 Hz Scan step = 80 Hz Scan data  150 kHz – 30 MHz RBW/VBW = 9 kHz Scan step = 4 kHz  other: EMI-Receiver or Scan-Mode  6 dB EMI-Receiver Mode  3dB Spectrum analyser Mode Analyzer Settings Detector Peak (pre-measurement) and Quasi-PK/Average (final if applicable) Mode: Repetitive-Scan, max-hold Sweep-Time Coupled – calibrated display if continuous signal otherwise adapted to EUT’s individual transmission duty-cycle General measurement procedures Please see chapter “Test system set-up radiated magnetic field measurements below 30 MHz” 5.4.4. Measurement Results The EUT is put on operation on middle channel only. If critical peaks are found (Margin <10 dB) the lowest and highest channels will be performed too.For more information please see the diagrams. Table of measurement results: Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark Result No. range no. no. Range No. PK AV QP 2.07 Middle 40 9 kHz-30 MHz 1 1 a mode, 6Mbps, Ch40    Pass 2.08 High 140 9 kHz-30 MHz 1 1 a mode, 6Mbps, Ch140    Pass n(HT20) Mode, MCS0, 2.10 Middle 40 9 kHz-30 MHz 1 1 Ch40    Pass n(HT20) Mode, MCS0, 2.11 Low 100 9 kHz-30 MHz 1 1 Ch100    Pass n(HT20) Mode, MCS0, 2.12 Low 149 9 kHz-30 MHz 1 1 Ch149    Pass Remark: For further details please refer diagrams in separate annex A1 TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 20 of 32 5.4.5. Correction factors due to reduced meas. distance (f< 30 MHz) The used correction factors when the measurement distance is reduced compared to regulatory measurement distance, are calculated according Extrapolation formulas valid for EUT’s with maximum dimension of 0.625xLambda. Formula 2+3+4 as presented in ANSI C63.10, Chapter 6.4.4 are used for the calculations of proper extrapolation factors. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 21 of 32 5.5. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz 5.5.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA receiver  377 ESCS30  001 ESS  489 ESU 40  620 ESU 26 spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix DC power  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE line voltage  4.35 V DC (fully charged internal battery) 5.5.2. Requirements/Limits  Part 15 Subpart B, §15.109, class B FCC  Part 15 Subpart C, §15.209 @ frequencies defined in §15.205  RSS-Gen., Issue 4, Chapter 8.9, Table 4+6 (licence-exempt radio apparatus)  RSS-Gen., Issue 4, Chapter 7.1.2, Table 2 (receiver) IC  ICES-003, Issue 6, Table 5 (Class B)  RSS-247, Issue 1, Chapter 5  C63.4-2014 ANSI  C63.10-2013 Radiated emissions limits, 3 meters Frequency [MHz] QUASI Peak [µV/m] QUASI-Peak [dBµV/m] 30 - 88 100 40.0 Limit 88 - 216 150 43.5 216 - 960 200 46.0 above 960 500 54.0 5.5.3. Restricted bands of operation (FCC §15.205/ RSS-Gen, Issue 4 Chapter 8.9, Table 4) MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 0.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.20725-4.20775 37.5-38.25 1645.5-1646.5 9.3-9.5 6.215-6.218 73-74.6 1660-1710 10.6-12.7 6.26775-6.26825 74.8-75.2 1718.8-1722.2 13.25-13.4 6.31175-6.31225 108-121.94 2200-2300 14.47-14.5 8.291-8.294 123-138 2310-2390 15.35-16.2 8.362-8.366 149.9-150.05 2483.5-2500 17.7-21.4 8.37625-8.38675 156.52475-156.52525 2690-2900 22.01-23.12 8.41425-8.41475 156.7-156.9 3260-3267 23.6-24.0 12.29-12.293 162.0125-167.17 3332-3339 31.2-31.8 12.51975-12.52025 167.72-173.2 3345.8-3358 36.43-36.5 12.57675-12.57725 240-285 3600-4400 -- 13.36-13.41 322-335.4 -- -- Remark: only spurious emissions are allowed within these frequency bands not exceeding the limits per §15.209 TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 22 of 32 5.5.4. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 0.8m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver Scan frequency range:  30 – 1000 MHz  other: (Analyzer) Settings Scan-Mode  6 dB EMI-Receiver Mode  3 dB spectrum analyser mode Detector Peak / Quasi-peak RBW/VBW 100 kHz/300 kHz Mode: Repetitive-Scan, max-hold Scan step 80 kHz Sweep-Time Coupled – calibrated display if continuous tx-signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for electric field measurement in the range 30 MHz to 1 GHz” 5.5.5. MEASUREMENT RESULTS The results are presented below in summary form only. For more information please consult the diagrams included in annex 1. Table of measurement results: Dia- Carrier Channel Set- OP- Used detector Result Frequency gram up mode Remark range no. no. no. Range No. PK AV QP 30 MHz – 3.07 Middle 40 1 1 a mode, 6Mbps, Ch40    Pass 1 GHz 30 MHz – 3.08 High 140 1 1 a mode, 6Mbps, Ch140    Pass 1 GHz 30 MHz – n(HT20) Mode, MCS0, 3.10 Middle 40 1 1    Pass 1 GHz Ch40 30 MHz – n(HT20) Mode, MCS0, 3.11 Low 100 1 1   s Pass 1 GHz Ch100 30 MHz – n(HT20) Mode, MCS0, 3.12 Low 149 1 1   s Pass 1 GHz Ch149 Remark: For further details please refer diagrams in separate annex A1 TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 23 of 32 5.6. General Limit - Radiated emissions, above 1 GHz 5.6.1. Test location and equipment FAR test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab. 337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU 40   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025 302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2  376 BBHA9120E  antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170   multimeter  341 Fluke 112      signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW DCpower  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery 350 Car battery  line voltage  4.35 V DC (fully charged internal battery) 5.6.2. Requirements/Limits (CLASS B equipment)  Part 15 Subpart B, §15.109 class B FCC  Part 15 Subpart C, §15.209 for frequencies defined in §15.205  Part 15 Subpart C, §15.407(b)(1)(2)(3) 9  RSS-Gen., Issue 4, Chapter 8.9, Table 4+6 (transmitter licence excempt)  RSS-Gen., Issue 4, Chapter 8.9, Table 2 (receiver) IC  ICES-003, Issue 6, Chapter 6.2.2, Table 7 (class B)  RSS-247, Issue 1, Chapter 6  C63.4-2014 ANSI  C63.10-2013 Limits Frequency AV AV Peak Peak [MHz] [µV/m] [dBµV/m] [µV/m] [dBµV/m] or [dBm/MHz] above 1 GHz for frequencies as defined in §15.205 500 54.0 5000 74.0 dBµV/m or RSS-Gen., Issue 4, §8.10 - Table 6 -27dBm/MHz §15.407(b) (68.5 dBµV/m) Or -- -- -- or RSS-247, Issue 1 -17dBm/MHz (78.5 dBµV/m) 5.6.3. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 1.5m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Spectrum- Scan frequency range:  1 – 18 GHz  18 – 25 GHz  18 – 40 GHz  other: Analyzer Scan-Mode  6 dB EMI-Receiver Mode  3 dB Spectrum analyser Mode settings Detector Peak and Average RBW/VBW 1 MHz / 3 MHz Mode: Repetitive-Scan, max-hold Scan step 400 kHz Sweep-Time Coupled – calibrated display if CW signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for radiated electric field measurements above 1 GHz” TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 24 of 32 5.6.4. Measurement Results The results are presented below in summary form only. For more information please consult the diagrams included in annex 1. Dia- Carrier Channel Set- OP- Used detector Result Frequency gram up mode Remark range no. no. no. Range No. PK AV QP 4.07 Middle 40 1-7GHz 1 1 a mode, 6Mbps, Ch40    Pass 4.07a Middle 40 7-18GHz 1 1 a mode, 6Mbps, Ch40    Pass 4.07b Middle 40 18-40GHz 1 1 a mode, 6Mbps, Ch40    Pass 4.08 High 140 1-7GHz 1 1 a mode, 6Mbps, Ch140    Pass 4.08a High 140 7-18GHz 1 1 a mode, 6Mbps, Ch140    Pass 4.08b High 140 18-40GHz 1 1 a mode, 6Mbps, Ch140    Pass n(HT20) Mode, MCS0, 4.10 Middle 40 1-7GHz 1 1    Pass Ch40 n(HT20) Mode, MCS0, 4.10a Middle 40 7-18GHz 1 1    Pass Ch40 n(HT20) Mode, MCS0, 4.10b Middle 40 18-40GHz 1 1    Pass Ch40 n(HT20) Mode, MCS0, 4.11 Low 100 1-7GHz 1 1    Pass Ch100 n(HT20) Mode, MCS0, 4.11a Low 100 7-18GHz 1 1    Pass Ch100 n(HT20) Mode, MCS0, 4.11b Low 100 18-40GHz 1 1    Pass Ch100 n(HT20) Mode, MCS0, 4.12 Low 149 1-7GHz 1 1    Pass Ch149 n(HT20) Mode, MCS0, 4.12a Low 149 7-18GHz 1 1    Pass Ch149 n(HT20) Mode, MCS0, 4.12b Low 149 18-40GHz 1 1    Pass Ch149 Remark: 1.) For further details please refer diagrams in separate annex A1 2.)As no critical harmonics within 6 dB margin from limits have been observed; hence measurements from 18 GHz-40 GHz have been not tested. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 25 of 32 5.7. General Limit - Band-edge compliance measurements 5.7.1. Test location and equipment FAR test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU 40   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025  302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2    antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170   multimeter  341 Fluke 112      signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW DC power  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery  350 Car battery  line voltage  4.35 V DC (fully charged internal battery) 5.7.2. Test condition and measurement test set-up Signal ink to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 1.5m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Spectrum- Scan frequency range:  1 – 18 GHz  18 – 25 GHz  18 – 40 GHz  other: see diagrams Analyzer Scan-Mode  6 dB EMI-Receiver Mode  3 dB Spectrum analyser Mode settings Detector Peak and Average RBW/VBW Band-edge: 1 MHz / 3 MHz Repetitive-Scan, max-hold Mode: 40kHz or 400 kHz Scan step Coupled – calibrated display if CW signal otherwise adapted to EUT’s individual duty-cycle Sweep-Time General measurement procedures Please see chapter “Test system set-up for radiated electric field measurements above 1 GHz” for general measurements procedures in anechoic chamber. 5.7.3. Requirements/ Limits  Part 15 Subpart C, §15.407(b)(1)(2)(3) FCC  Part 15 subpart C, §15.209 @ frequencies defined in §15.205  RSS-247, Issue 1, Chapter 5.5; RSS-Gen: Issue 4: §8.9 Table 4+5+6 IC  RSS-Gen: Issue 4: §8.9, Table 4+6  C63.10-2009 for TX-mode ANSI  C63.10-2013, Chapter 6.10.6 KDB Guidance no.  789033 D01 General UNII test procedures v01r03’: G(2)(c)(d), G(3)(d) Limits AV Peak accord. Above 1GHz [dBµV/m] [dBµV/m] §15.205 54.0 74.0 EIRP – limit for outside operating frequency band Carrier operating Peak [dBm] Peak [dBµV/m]1.) frequency band [MHz] 30 MHz to 40 GHz 30 MHz to 40 GHz@3m 5.15 – 5.25 GHz -27.0 68.2 Limits 5.25 – 5.35 GHz -27.0 68.2 accord. 5.47 – 5.725 GHz -27.0 68.2 §15.407 -27.0 68.2 (10 MHz greater above/below band edge) (10 MHz greater above/below band edge) 5.725 – 5.825 GHz -17.0 78.2 (within 10 MHz offset to band-edge) (within 10 MHz offset to band-edge) Remark: 1.) Conversion formula between EIRP and field strength used (Please read measurement method). 5.7.4. Measurement method For uncritical results where a measurement bandwidth of 1MHz can clearly show the compliance without influencing the results, a field strength measurement was performed only. For critical results a Marker-Delta marker method was used for showing compliance to restricted bands according §15.205. The method is according ANSI 63.10:2013 “Marker-Delta method”, §6.9.3. The method consists of three independent steps: 1. Step: Prior to the measurement the fundamental radiated In-Band field strength was performed. The determined value is used as reference value. TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 26 of 32 2. Step: Second step consist of finding the relative attenuation between the fundamental emission and the maximum local out-of-band emission (within 2 MHz range around the band edge either on the band-edge directly or some modulation product if the level is greater than that on the band-edge) when measured with lower resolution bandwidth. 3. Step: The delta value recorded in step 2 will be subtracted from value recorded in step 1, thus giving the required field strength at the band-edge. This value must fulfil the requirements for radiated spurious emissions in restricted bands in §15.205 with the general limits of §15.209. The formula EIRP[dBm] = E [dBµV/m] - 95.2 for radiated measurements, which used field strength at 3 meters to convert the value in dBm. 5.7.5. EUT settings The EUT was instructed to send with maximum intended power levels according to applicants instructions. 5.7.6. Results: 5.7.6.1. Non-restricted bands near-by - limits according FCC §15.407 and RSS-247, Issue 1, Chapter 5.5 Fundamental Value Diagram Channel Restricted [dBuV/m] Peak-Value at Band- Limit Margin Verdict Remark: No. No. band ? Average- Edge [dBuV/m] [dBuV/m] [dB] Peak-Value Value a mode, 6 Mbps, 9.15 100 No 104.94 97.6 55.70 68.2 12.5 Pass CH100 n(HT20) mode, MCS0, 9.19 100 No 106.10 97.21 57.20 68.2 11.0 Pass CH100 a mode, 6 Mbps, 9.16 140 No 104.80 97.74 59.80 68.2 8.40 Pass CH140 n(HT20) mode, MCS0, 9.20 140 No 106.13 96.9 59.66 68.2 8.54 Pass CH140 n(HT20) mode, MCS0, 9.21 149 No 105.86 96.71 65.26 78.2 12.94 Pass CH149 n(HT20) mode, MCS0, 9.22 165 No 106.81 97.96 62.76 78.2 15.44 Pass CH165 5.7.6.2. Restricted bands near-by (§15.205 with limits accord. FCC §15.209) and (RSS-Gen, Issue 4, Chapter 8.10) Fundamental Value Value of Band-Edge Limits Margin Diagram Channel Restricted [dBuV/m] [dBuV/m] [dBuV/m] [dB] Verdict: Remark: No. No. band ? Peak- Average- Peak- Average- Peak- Average- Peak- Average- Value Value Value Value Value Value Value Value a mode, 6 9.13 36 Yes 105.14 98.00 54.60 44.60 74 54 19.40 9.40 Pass Mbps, CH36 n(HT20) 9.17 36 Yes 107.69 98.63 57.21 45.90 74 54 16.79 8.10 Pass mode, MCS0, CH36 a mode, 6 9.14 64 Yes 104.59 97.5 54 44.76 74 54 20 9.24 Pass Mbps, CH64 n(HT20) 9.18 64 Yes 106.28 97.38 53.96 44.71 74 54 20.04 9.29 Pass mode, MCS0, CH64 Remark: Please refer chapter 5.1 for applicable duty-cycle correction factor 5.7.7. Verdict: Pass TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 27 of 32 5.8. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it’s contribution to the overall uncertainty according it’s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based on a RF-Measurement Reference Frequency range Remarks confidence level of 95% Conducted emissions 9 kHz - 150 kHz 4.0 dB CISPR 16-2-1 - (U CISPR) 150 kHz - 30 MHz 3.6 dB Radiated emissions 30 MHz - 1 GHz 4.2 dB CISPR 16-2-3 E-Field Enclosure 1 GHz - 18 GHz 5.1 dB Disturbance power CISPR 16-2-2 30 MHz - 300 MHz - - Substitution Power Output radiated - 30 MHz - 4 GHz 3.17 dB method Cel- Cel- Set-up No. BT1 W1 W2 -- C1 C2 Power Output conducted - 9 kHz - 12.75 GHz N/A 0.60 0.7 0.25 N/A -- - 12.75 - 26.5GHz N/A 0.82 -- N/A N/A -- Conducted emissions - 9 kHz - 2.8 GHz 0.70 N/A 0.70 N/A 0.69 -- N/A - not on RF-port 2.8 GHz - 12.75GHz 1.48 N/A 1.51 N/A 1.43 -- applicable 12.75 GHz - 18GHz 1.81 N/A 1.83 N/A 1.77 -- 18 GHz - 26.5GHz 1.83 N/A 1.85 N/A 1.79 -- 0.1272 ppm (Delta Marker) Frequency Occupied bandwidth - 9 kHz - 4 GHz error 1.0 dB Power - 0.1272 ppm (Delta Marker) Frequency Emission bandwidth 9 kHz - 4 GHz error - See above: 0.70 dB Power Frequency stability - 9 kHz - 20 GHz 0.0636 ppm - 150 kHz - 30 MHz 5.0 dB Magnetic Radiated emissions 30 MHz - 1 GHz 4.2 dB field - Enclosure 1 GHz - 20 GHz 3.17 dB E-field Substitution Table: measurement uncertainties, valid for conducted/radiated measurements TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 28 of 32 6. Abbreviations used in this report The abbreviations ANSI American National Standards Institute AV , AVG, CAV Average detector EIRP Equivalent isotropically radiated power, determined within a separate measurement EGPRS Enhanced General Packet Radio Service EUT Equipment Under Test FCC Federal Communications Commission, USA IC Industry Canada n.a. not applicable Op-Mode Operating mode of the equipment PK Peak RBW resolution bandwidth RF Radio frequency RSS Radio Standards Specification, Dokuments from Industry Canada Rx Receiver TCH Traffic channel Tx Transmitter QP Quasi peak detector VBW Video bandwidth ERP Effective radiated power 7. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) FCC, Federal Communications 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) MRA US-EU Commission 558 Radiated Measurements above 1 GHz, 3 m (FAR) 0003 Laboratory Division, USA 348 Mains Ports Conducted Interference Measurements (MRA US-EU 0003) 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) IC, Industry Canada Certification 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) and Engineering Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 487 R-2666 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) VCCI, Voluntary Control Council 550 G-301 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) for Interference by Information 348 C-2914 Mains Ports Conducted Interference Measurements Technology Equipment, Japan 348 T-1967 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 29 of 32 8. Instruments and Ancillary 8.1. Used equipment “CTC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 8.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 9.15.00 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 9.15.00 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 Setup V03.26, Test programm component V03.02.20 670 Univ. Radio Communication Tester CMU 200 106833 µP1 =V8.50, Firmware = V.20 689 Vector Signal Generator SMU200 100970 02.20.360.142 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 30 of 32 8.1.2. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 001 EMI Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 30.05.2017 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 12 M - 30.05.2017 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 12 M - 30.05.2017 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 30.04.2017 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 30.05.2019 020 Horn Antenna 18 GHz (Subst 1) 3115 9107-3699 EMCO 36/12 M - 31.03.2017 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 30.04.2018 030 Loop Antenna (H-field) HFH-Z2 879604/026 Rohde & Schwarz 36 M - 30.04.2018 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 30.04.2017 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 WRCT 1900/2200-5/40- 066 notch filter (WCDMA; FDD1) 5 Wainwright GmbH 12 M 1g 30.06.2016 10EEK 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 30.04.2018 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 30.04.2018 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 BOCONSULT 36 M - 30.05.2019 136 adjustable dipole antenna (Dipole 1) 3121C-DB4 9105-0697 EMCO 36 M - 30.04.2018 140 Signal Generator SMHU 831314/006 Rohde & Schwarz 24 M - 30.05.2018 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 30.05.2018 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 30.05.2018 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 30.05.2019 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 30.05.2018 266 Peak Power Sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 30.05.2018 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 287 pre-amplifier 25MHz - 4GHz AMF-2D-100M4G-35-10P 379418 Miteq 12 M 1c 30.06.2017 291 high pass filter GSM 850/900 WHJ 2200-4EE 14 Wainwright GmbH 12 M 1c 30.06.2017 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 12 M - 30.05.2017 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 31.03.2017 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 31.03.2017 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 Heraeus Vötsch Pre-m 2 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 30.05.2018 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 30.04.2017 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 355 Power Meter URV 5 891310/027 Rohde & Schwarz 24 M - 30.05.2018 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 30.04.2017 371 Bluetooth Tester CBT32 100153 R&S 36 M - 30.05.2019 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 12 M - 30.05.2017 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 30.05.2017 389 Digital Multimeter Keithley 2000 0583926 Keithley 24 M - 30.04.2017 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 30.05.2017 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 30.04.2017 439 UltraLog-Antenna HL 562 100248 Rohde & Schwarz 36 M - 31.03.2017 System CTC-FAR-EMI- ETS-Lindgren / 443 CTC-FAR-EMI-RSE - 12 M 5 30.06.2017 RSE CETECOM WRCT 1850.0/2170.0- Wainwright Instruments 448 notch filter WCDMA_FDD II 5 12 M 1c 30.06.2017 5/40- GmbH TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 31 of 32 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due WRCT 824.0/894.0-5/40- 449 notch filter WCDMA FDD V 1 Wainwright 12 M 1c 30.06.2017 8SSK 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 30.04.2017 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 30.05.2018 467 Digital Multimeter Fluke 112 89680306 Fluke USA 36 M - 30.04.2018 468 Digital Multimeter Fluke 112 90090455 Fluke USA 36 M - 30.04.2018 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 30.04.2017 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d AMF-5D-02501800-25- 484 pre-amplifier 2,5 - 18 GHz 1244554 Miteq 12 M - 30.06.2017 10P System EMI field (SAR) ETS Lindgren / 487 System CTC NSA-Verification SAR-EMI - 24 M - 31.07.2017 NSA CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 30.05.2017 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- 503 band reject filter WRCG 824/849-814/859- SN 5 Wainwright pre-m 2 WRCA 800/960-02/40- 512 notch filter GSM 850 SN 24 Wainwrght 12 M 1c 30.06.2017 6EEK 517 relais switch matrix HF Relais Box Keithley SE 04 Keithley pre-m 2 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 30.04.2017 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 530 10 dB Broadband resistive power divider R 416110000 LOT 9828 - pre-m 2 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 30.05.2017 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 30.04.2017 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz 36/12 M - 31.07.2018 System CTC S-VSWR Verification SAR- System EMI Field SAR S- ETS 550 - 24 M - 31.07.2017 EMI VSWR Lindgren/CETECOM 552 high pass filter 2,8-18GHz WHKX 2.8/18G-10SS 4 Wainwright 12 M 1c 30.06.2017 557 System CTC-OTA-2 R&S TS8991 - Rohde & Schwarz 12 M 5 30.09.2016 System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 19.04.2017 VSWR 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia 36/12 M - 31.03.2019 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz pre-m - 594 Wideband Radio Communication Tester CMW 500 101757 Rohde & Schwarz 12 M - 30.04.2017 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz pre-m - 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Rohde & Schwarz 24 M - 30.04.2017 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 30.04.2017 601 medium-sensitivity diode sensor NRV-Z5 (Reserve) 8435323/003 Rohde & Schwarz 24 M - 30.04.2017 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 30.05.2018 617 Power Splitter/Combiner ZFSC-2-2-S+ S F987001108 Mini Circuits - 2 618 Power Splitter/Combiner 50PD-634 600994 JFW Industries USA - 2 619 Power Splitter/Combiner 50PD-634 600995 JFW Industries, USA - 3 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 30.05.2017 621 Step Attenuator 0-139 dB RSP 100017 Rohde & Schwarz pre-m 2 625 Generic Test Load USB Generic Test Load USB - CETECOM - 2 201.0999.9302.6.4.1.4 627 data logger OPUS 1 G. Lufft GmbH 24 M - 30.04.2017 3 634 Spectrum Analyzer FSM (HF-Unit) 826188/010 Rohde & Schwarz pre-m 2 HDMI cable with Ethernet 637 High Speed HDMI with Ethernet 1m - KogiLink - 2 1m 638 HDMI Kabel with Ethernet 1,5 m flach HDMI cable with Ethernet - Reichelt - 2 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 641 HDMI cable with Ethernet Certified HDMI cable with - PureLink - 2 644 Amplifierer ZX60-2534M+ SN865701299 Mini-Circuits - - 670 Univ. Radio Communication Tester CMU 200 106833 Rohde & Schwarz 24 M - 30.05.2018 671 DC-power supply 0-5 A EA-3013S - Elektro Automatik pre-m 2 678 Power Meter NRP 101638 Rohde&Schwarz pre-m - 683 Spectrum Analyzer FSU 26 200571 Rohde & Schwarz 12 M - 30.05.2017 Narda Safety Test 686 Field Analyzer EHP-200A 160WX30702 24 M - 30.04.2017 Solutions 687 Signal Generator SMF 100A 102073 Rohde&Schwarz 12 M - 30.05.2017 688 Pre Amp JS-18004000-40-8P 1750117 Miteq pre-m - 690 Spectrum Analyzer FSU 100302/026 Rohde&Schwarz 12 M - 30.05.2017 692 Bluetooth Tester CBT 32 100236 Rohde & Schwarz 36 M - 31.03.2017 TR2-20842790-15-8b

Test Report 2-20842790-15-8b, Page 32 of 32 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 697 Power Splitter ZN4PD-642W-S+ 165001445 Mini-Circuits - 2 8.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months, between this every 12 months internal validation 36/12 M Calibration every 36 months, between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration 9. Versions of test reports (change history) Version Applied changes Date of release -- Initial release 2016-10-12 -- -- -- TR2-20842790-15-8b


Document Created: 2016-10-31 11:33:48
Document Modified: 2016-10-31 11:33:48
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC