Test report Bluetooth LE - FCC report

FCC ID: U4GFX4WB

Test Report

Download: PDF
FCCID_3768877

PARTIAL T E S T R E P O R T No.: 17-1-0180901T11a According to: FCC Regulations Part 15.205 Part 15.209 Part 15.247 for Datalogic S.r.l. FALCON X4 Type: E00ANM4HS0GF0A4 FCC ID: U4GFX4WB Laboratory Accreditation and Listings Voluntary Controls for Industry Canada Electromagnetic Emissions Reg. No.: 3462D-1 Reg. No.: MRA US-EU 0003 Reg. No.: 3462D-2 R-2666 C-2914, Reg. No.: 3462D-3 T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 31 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 17-1-0180901T11a, Page 2 of 31 Table of contents 1. SUMMARY OF TEST RESULTS...................................................................................................................... 3 1.1. Tests measurement overview according to FCC Standard .............................................................................. 3 2. ADMINISTRATIVE DATA ............................................................................................................................... 5 2.1. Identification of the testing laboratory ............................................................................................................. 5 2.2. Test location .................................................................................................................................................... 5 2.3. Organizational items ........................................................................................................................................ 5 2.4. Applicant’s details ........................................................................................................................................... 5 2.5. Manufacturer’s details ..................................................................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................. 6 3.1. Certification Data of Main EUT declared by Applicant .................................................................................. 6 3.2. Bluetooth LE Technical Data of Main EUT as Declared by Applicant ........................................................... 7 3.3. EUT: Type, S/N etc. and short descriptions used in this test report ................................................................ 8 3.4. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions .................................................................. 8 3.5. EUT set-ups ..................................................................................................................................................... 8 3.6. EUT operating modes ...................................................................................................................................... 9 3.7. Configuration of cables used for testing .......................................................................................................... 9 4. DESCRIPTION OF TEST SYSTEM SET-UP’S .............................................................................................. 10 4.1. Test system set-up for conducted measurements on antenna port ................................................................... 10 4.2. Test system set-up for radiated magnetic field measurements below 30 MHz ................................................ 11 4.3. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz ............................................... 12 4.4. Test system set-up for radiated electric field measurement above 1 GHz ....................................................... 13 5. MEASUREMENTS ............................................................................................................................................. 14 5.1. Duty-Cycle....................................................................................................................................................... 14 5.2. RF-Parameter – RF Power conducted.............................................................................................................. 16 5.3. General Limit - Radiated field strength emissions below 30 MHz .................................................................. 18 5.4. General Limit - Radiated field strength emissions. 30 MHz - 1 GHz .............................................................. 20 5.5. General Limit - Radiated emissions. above 1 GHz .......................................................................................... 22 5.6. RF-Parameter - Radiated Band Edge compliance measurements .................................................................... 24 5.7. Measurement uncertainties .............................................................................................................................. 26 6. ABBREVIATIONS USED IN THIS REPORT ................................................................................................. 27 7. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ......................... 27 8. INSTRUMENTS AND ANCILLARY ................................................................................................................ 28 TC” ......................................................................................................................................................................... 28 9. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ............................................................................. 31 Table of Annex Annex No. Contents Reference Description Total Pages Annex 1 Test results CETECOM_TR17-1-0180901T11a-A1 20 Annex 2 External photographs of EUT CETECOM_TR17-1-0180901T11a-A2 9 Annex 2 Internal photographs of EUT CETECOM_TR17-1-0180901T11a-A3 12 Annex 4 Test set-up photographs CETECOM_TR17-1-0180901T11a-A4 10 The listed attachments are an integral part of this report. CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 3 of 31 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The test results apply exclusively to the test samples as presented in this report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. Also we refer on special conditions which the applicant should fulfill according §2.927 to §2.948, special focus regarding modification of the equipment and availability of sample equipment for market surveillance tests. The presented Equipment Under Test(in this report, hereinafter referred as EUT) : FALCON X4 integrates total 1 of pre-certified module WL18MODGI (FCC ID: Z64-WL18DBMOD) & supports following technologies : EUT supported Technologies which are not tested within this test report EUT supported Technology Test Report Reference Bluetooth FHSS (BR-EDR) Modes: 2402 – 2480 MHz CETECOM_TR17-1-0180901T10a WLAN 802.11b/g/n(HT20) Modes: 2412 – 2462 MHz CETECOM_TR17-1-0180901T12a WLAN 802.11a/n(HT20)/n(HT40)Modes: 5150–5850 MHz CETECOM_TR17-1-0180901T16a AC Power Lines - Internal Battery Charging CETECOM_TR17-1-0180901T18a EUT supported Technologies which are tested within this test report - 2.4 GHz Bluetooth Low Energy Modes : 2402 – 2480 MHz Following test cases have been performed to show compliance with valid Part 15.205/15.209/15.247 of the FCC CFR Title 47 Rules, Edition 4th November 2016. 1.1. Tests measurement overview according to FCC Standard References and Limits EUT EUT Test cases Port op. Result FCC Standard Test limit set-up mode TX-Mode 6 dB Antenna terminal §15.247 (a) (2) At least 500 kHz -- -- Remark 2) bandwidth (conducted) 99% occupied Antenna terminal 2.1049(h) 99% Power bandwidth -- -- Remark 2) bandwidth (conducted) Transmitter Peak Antenna terminal §15.247 (b) (3) <1W 2 1 Pass output power (conducted) Power Spectral Antenna terminal §15.247 (e) < 8 dBm in 3 kHz band -- -- Remark 2) Density (conducted) Operation within Transmitter Antenna terminal -- designated operational -- -- Not tested frequency stability (conducted) band Transmitter Peak < 1 W for antenna Enclosure output power §15.247 (b) (3) with directional gain -- -- Remark 2) (radiated) radiated less than 6 dBi. 20 dBc Conducted Out-Of-Band RF- Antenna terminal §15.247 (d) Emissions in restricted -- -- Remark 2) emissions (conducted) bands CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 4 of 31 Emissions in restricted Band-Edge Enclosure bands must meet the §15.247 (d) 1 1 Pass emissions (radiated) general field strength radiated limits General field Enclosure + Emissions in restricted §15.247 (d) strength emissions Interconnecting bands must meet the §15.205 1 1 Pass + restricted cables general field-strength §15.209 bands (radiated) radiated limits AC-Power Lines AC-Power lines AC Power line Conducted or §15.207(a) -- -- Remark 1) conducted limits Emissions Battery Charger Remark 1) : Not tested in this report as Bluetooth test configuration was operated using fully charged internal battery Refer separate report CETECOM_TR17-1-0180901T18a Remark 2): Refer WL18MODGI (FCC ID: Z64-WL18DBMOD) Report No. FR4O0971B, Rev.01, issue date Dec 19,2014 Specific Absorption Rate (SAR) Measurements (separation distance user to RF-radiating element within 20cm) References & Limits EUT EUT Test cases Port op. Result FCC Standard Test Limit set-up mode Specific Absorption §2.1091 Rate (SAR) for Cabinet §2.1093 Devices Used by the Specific + Refer separate General Public Absorption Inter- + report (Uncontrolled -- -- CETECOM_TR17- Rate (SAR) connecting IEEE 1528-2013 Environment) 1-0180901T09a requirements cables + : 1.6 W/Kg as (radiated) KDB 865664D01v0r04 averaged over any 1 g tissue ...................................................... .................................................... Dipl.-Ing. Niels Jeß M.Sc. Ajit Phadtare Responsible for test section Responsible for test report CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 5 of 31 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Rachid Acharkaoui Deputy: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report and Project leader: M.Sc. Ajit Phadtare Receipt of EUT: 2017-10-20 Date(s) of test: 2017-10-12 to 2017-12-25 Date of report: 2017-12-27 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 13.02 2.4. Applicant’s details Applicant’s name: Datalogic S.r.l. Address: Via S. Vitalino, 13 40012, Lippo di Calderara di Reno (BO) ITALY Contact: Mr. Francesco Rossi 2.5. Manufacturer’s details Manufacturer’s name: same as Applicant Address: same as Applicant CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 6 of 31 3. Equipment under test (EUT) 3.1. Certification Data of Main EUT declared by Applicant EUT Model FALCON X4 EUT Model Type E00ANM4HS0GF0A4 EUT Type Portable Mobile Computer EUT Applications Shopping Applications & General Purpose Mobile Computer FCC ID U4GFX4WB Additional Information: Integrated Module Integrated Module WL18MODGI Module Certification FCC ID Z64-WL18DBMOD Number of Integrated Modules 1 Additional Information : Supported Technologies Technology Modes Frequency Range Remarks Bluetooth LE Bluetooth Low Energy 2402 MHz – 2480 MHz refer chapter 3.2 Bluetooth FHSS Bluetooth BR-EDR 2402 MHz – 2480 MHz not tested under this report WLAN 2.4 GHz WLAN 802.11b/g/n(HT20) 2412 MHz – 2462 MHz not tested under this report WLAN 5 GHz WLAN 802.11a/n(HT20)/n(HT40) 5150 MHz –5850 MHz not tested under this report CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 7 of 31 3.2. Bluetooth LE Technical Data of Main EUT as Declared by Applicant EUT Model FALCON X4 EUT Model Type E00ANM4HS0GF0A4 EUT Type Portable Mobile Computer EUT Applications Shopping applications & general purpose mobile computer Hardware Version BETA Software Version Android 4.4.4 Firmware Version 2.01.46.20180109 Frequency Band 2.4 GHz ISM Band (2400 MHz - 2483.5 MHz) Frequency Channels (Range) Channel 37: 2402 MHz to Channel 39: 2480 MHz Number of Channels 40 (37 Hopping + 3 Advertising) Channels Power Settings +7 dBm (According to Applicant’s Declaration Max. Rated Power Values) Nominal Channel Bandwidth 1 MHz Type of DSSS Mode Low Energy (LE) Mode : Modulation | Data Rate  BT 4.0: GFSK | 1 Mbps Antenna Details Integrated (ANT1 & ANT2) Antenna Connections Primary Antenna : ANT1 (BT LE) Secondary Antenna: ANT2 not used Antenna Type Laird PCBA Antenna ANT1 Gain (Peak) 3.04 dBi (2400 MHz – 2500 MHz) (According to Applicant’s Declaration) ANT2 Gain (Peak) 2.80 dBi (2400 MHz – 2500 MHz) (According to Applicant’s Declaration) Total Number of Modules 1 (WL18MODGI Module FCC ID: Z64-WL18DBMOD) Total Number of Antennas 2 Primary Antenna : ANT1 (BT LE) Secondary Antenna: ANT2 not used Test Mode Settings Datalogic RFTest Application MAX Field Strength Average Value: 97.392 dBµV/m Peak Value : 98.058 dBµV/m (Radiated@3m) with Duty Cycle Correction : 1.99 dB  Internal Battery : BT-26 | Li-ion|3.7- 4.2VDC 5200mAh Power Supply (2 Cylindrical Cells) Special EMI Components -- EUT Sample Type  Production  Pre-Production  Engineering Firmware  for normal use  Special version for test execution : Datalogic RFTest FCC label attached  Yes  No For further details refer Applicants Declaration & following technical documents Description of Reference Document (supplied by applicant) Version Total Pages FALCON X4_Test-Tools_Quick_Start_Instructions Rev: 0 Date: 14/09/2017 45 822002580 Rev: A FALCON X4_Quick Start Guide 2 December 2017 FALCON X4 Hardware Modifications December 2017 7 Datalogic Falcon FX4 Antenna_Rev E Rev:E Date : 30/10/2017 15 CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 8 of 31 3.3. EUT: Type, S/N etc. and short descriptions used in this test report Short Serial Hardware Software Descrip- EUT Type Number Status Status tion*) HW SW Version: Version: Android 4.4.4 BETA EUT A FALCON X4 E00ANM4HS0GF0A4 Z17P02008 Firmware P/N: Version: 945550001 2.01.46.2018 0109 HW SW Version: Version: Android 4.4.4 BETA EUT B FALCON X4 E00ANM4HS0GF0A4 Z17P02012 Firmware P/N: Version: 945550001 2.01.46.2018 0109 *) EUT short description is used to simplify the identification of the EUT in this test report. 3.4. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE short SW S/N HW descrip- Auxiliary Equipment Type software serial number hardware status tion *) status AE 1 -- -- -- -- -- *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. 3.5. EUT set-ups EUT set- Combination of EUT and AE Description up no.*) set. 1 EUT A Radiated measurements set. 2 EUT B + Cable 1 + Cable 2 Conducted measurements *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 9 of 31 3.6. EUT operating modes EUT Description of Additional information operating operating modes mode no.*) For Bluetooth Low Energy Modes tests are carried out with different Channels | Modulation | Data Rate Combinations with help of Datalogic RFTest Application. The EUT was put to Fixed Channel (Modulated) Continuous transmissions mode | Pattern Length : 37 | PRBS9 with help of Bluetooth Low Energy Datalogic RFTest Application. Modes* op. 1 (Channel Type | Frequency | Power Settings) TX-Fixed Channel Lowest Channel : 0 : 2402 MHz | Power : +7 dBm (Modulated) Middle Channel :19: 2440 MHz | Power : +7 dBm Highest Channel :39: 2480 MHz | Power : +7 dBm *Other supported wireless technologies were put in idle mode using special test software Bluetooth Low Energy The EUT was put to Fixed Channel (Modulated) Continuous Modes* receiving mode with help of Datalogic RFTest Application. op. 2 RX-Fixed Channel *Other supported wireless technologies were put in idle mode using (Modulated) special test software *) EUT operating mode no. is used to simplify the test report. 3.7. Configuration of cables used for testing Cable number Description Connections Cable length Cable 1 RF –SMA Cable EUT ANT1 to Power Meter 0.08 m Cable 2 RF –SMA Cable EUT ANT2 to 50 Ω Termination 0.08 m CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 10 of 31 4. Description of test system set-up’s 4.1. Test system set-up for conducted measurements on antenna port Bluetooth conducted RF-Setup 1 (BT1 Set-up) General description: The EUT‘s RF-signal is coupled out by a suitable antenna coupling connector (1). The signal is first attenuated (2) then connected to the power meter (3) for conducted power measurements. The specific attenuation loss is determined prior to the measurement within a set-up attenuation measurement. These are then taken into account by correcting the measurement readings. Schematic: Testing method: ANSI C63.10:2013, KDB 558074 D01 DTS Meas.Guidance v04 Used Equipment Passive Elements Test Equipment Remark:  20 dB Attenuator  Power Meter See List of equipment under each test  Low loss RF-cables  DC-Power Supply case and chapter 8 for calibration  Spectrum- Analyser info Measurement uncertainty See chapter 5.7 CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 11 of 31 4.2. Test system set-up for radiated magnetic field measurements below 30 MHz Specification: ANSI C63.10-2013 chapter 6.4 (§6.4.4.2) General Description: Evaluating the radiated field emissions are done first by an exploratory emission measurement and a final measurement for most critical frequencies determined. The loop antenna was placed at 1 m height above ground plane and 3 m measurement distance from set-up for investigations. Because of reduced measurement distance, correction data were applied, as stated in chapter “General Limit - Radiated field strength emissions below 30 MHz“. The tests are performed in the semi anechoic room recognized by the regulatory commission. Schematic: Testing method: Exploratory, preliminary measurement Final measurement on critical frequencies The EUT and it’s associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 0.8 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (step cable position, etc. 90°, range 0°to 360°) and the EUT itself either on 3-orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT), the emission spectrum was recorded. The precisely. After this step, for all identified critical loop antenna was moved at least to frequencies, the maximum peak was determined. 2-perpendicular axes (antenna vector in direction of EUT and parallel to EUT) in order to maximize Following parameters were varied: the turntable the emissions. The results are documented in a angle continuously in the range 0 to 360 degree, diagram. Critical frequencies (low margin to the EUT itself either over 3-orthogonal axis (not limit) are saved within a data reduction table for defined usage position) or 2-orthogonal axis further investigations. If various operating modes (defined usage position). are supported, further investigations are made to find the worst-case. Also the interconnection On the determined worst-case position, a final cables and equipment position were varied in measurement with necessary bandwidth and order to maximize the emissions. detector according standard has been carried out. Formula: EC = ER + AF + CL + DF - GA AF =Antenna factor CL = Cable loss M = LT-EC DF= Distance correction factor EC = Electrical field – corrected value ER = Receiver reading GA= Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. Distance correction: Reference for applied correction (extrapolating) factors due to reduced measurement distance: ANSI C63.10:2013, §6.4.4.2 - Equations (2) + (3) + (4) CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 12 of 31 4.3. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz Specification: ANSI C63.4-2014 chapter 8.2.3, ANSI C63.10-2013 chapter 6.5 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a NSA-compliant semi anechoic room (SAR) recognized by the regulatory commissions. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are placed Based on the exploratory measurements, the most on a non-conductive position manipulator (tipping critical frequencies are re-measured by main- device) of 0.8 m height which is placed on the taining the EUT’s worst-case operation mode, cable turntable. By rotating the turntable (range 0° to position, etc. either on 10m OATS or 3m semi- 360°, step 90°) and the EUT itself either on 3- anechoic room. orthogonal axis (portable equipment) or 2- orthogonal axis (defined operational position of First a frequency zoom around the critical frequency EUT) the emission spectrum and it’s is done to locate the frequency more precisely. After characteristics was recorded with an EMI- this step, for all identified critical frequencies, the receiver, broadband antenna and software. maximum peak was determined. Measurement antenna: horizontal and vertical, Following parameters were varied: the turntable heights: 1,0 m and 1,82 m as worst-case angle continuously in the range 0 to 360 degree, the determined by an exploratory emission EUT itself either over 3-orthogonal axis (not measurements. The results are documented in a defined usage position) or 2-orthogonal axis diagram. Critical frequencies (low margin to (defined usage position). The measurement antenna limit) are saved within a table for further height between 1 m and 4 m. investigations. If various operating modes are supported, further investigations are made to find On the determined worst-case position, a final the worst-case of them. Also the interconnection measurement with necessary bandwidth and cables and equipment position were varied in detector according standard has been carried out. order to maximize the emissions. Formula: EC = ER + AF + CL + DF - GA (1) AF = Antenna factor CL = Cable loss M = LT - EC (2) DF = Distance correction factor (if used) EC = Electrical field – corrected value ER = Receiver reading GA = Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 13 of 31 4.4. Test system set-up for radiated electric field measurement above 1 GHz Specification: ANSI C63.4-2014 chapter 8.3, ANSI C63.10-2013 chapter 6.6.3.3 & 6.6.4 General Description: Evaluating the emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a CISPR 16-1-4:2010 compliant fully anechoic room (FAR) recognized by the regulatory commission. The measurement distance was set to 3 meter for frequencies up to 18 GHz and 2 meter above 18 GHz. A logarithmic periodic antenna is used for the frequency range 30 MHz to 1 GHz. Horn antennas are used for frequency range 1 GHz to 40 GHz. The EUT is aligned within 3 dB beam width of the measurement antenna with three orthogonal axis measurements on the EUT. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are placed Based on the exploratory measurements, the most on a non-conductive position manipulator (tipping critical frequencies are re-measured by main- device) of 1.55 m height which is placed on the taining the EUT’s worst-case operation mode, turntable. By rotating the turntable (range 0° to cable position, etc. 360°, step 15°) and the EUT itself either on 3- orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT) the emission spectrum and it’s precisely. After this step, for all identified critical characteristics was recorded with an EMI- frequencies, the maximum peak was determined. receiver, broadband antenna and software. Following parameters were varied: the turntable The measurements are performed in horizontal angle continuously in the range 0 to 360 degree, and vertical polarization of the measurement the EUT itself over 3-orthogonal axis and the antennas. The results are documented in a height for EUT with large dimensions. diagram. Critical frequencies (low margin to limit) are saved within a table for further On the determined worst-case position, a final investigations. If various operating modes are measurement with necessary bandwidth and supported, further investigations are made to find detector according standard has been carried out. the worst-case of them. Also the interconnection On the determined worst-case position, a final cables and equipment position were varied in measurement with necessary bandwidth and order to maximize the emissions. detector according standard has been carried out. Formula: EC = ER + AF + CL + DF - GA (1) EC = Electrical field – corrected value ER = Receiver reading M = LT - EC (2) M = Margin LT = Limit AF = Antenna factor CL = Cable loss DF = Distance correction factor (if used) GA = Gain of pre-amplifier (if used) All units are dB-units, positive margin means value is below limit. CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 14 of 31 5. Measurements 5.1. Duty-Cycle 5.1.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') Ambient Climatic conditions Temperature: (22±2)°C Rel. humidity: (45±15)% Test Site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  Equipment  331 HC 4055      Spectr. Analys.  683 FSU26  120 FSEM  264 FSEK  693 TS8997   Power Meter  262 NRV-S  266 NRV-Z31  265 NRV-Z33  261 NRV-Z55  356 NRV-Z1  Multimeter  341 Fluke 112      DC Power  086 LNG50-10  087 EA3013  354 NGPE 40  349 car battery  350 Car battery  463 HP3245A Supply Voltage  230 V 50 Hz via public mains 4.20 V DC (fully charged internal battery) Otherwise Attenuator  530  K4 Cable 10dB Method of measurement:  conducted  radiated A special firmware program is used for test purposes. In contrast to normal operating mode a higher duty- cycle is set in order to facilitate the measurements. This is maximized at the extent possible. The necessary duty-cycle correction factor is determined on nominal conditions on 1 channel for all sub-bands. It is assumed that no noticeable changes occur when tested on other channels or climatic conditions. Calculated with following formulas: x Txon 1 Duty cycle: Duty cycle factor [dB]: 10 log  Txon  Txoff x CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 15 of 31 Results: Set-up No.: 2 Op. Mode: 1 DUTY-CYCLE Measurement TX ON TX OFF Correction- BT-LE GFSK Marker 1 Marker 2 Marker 3 Marker 2 - Marker 3 - Duty Cycle Factor: Plot No. Marker 1 Marker 2 100log(1/DC) Data Rate ms ms ms ms ms (%) (dB) (Remark 1) BT-LEMode| B.W. 1 MHz | SISO | Ch 19 (2440 MHz) | 7 dBm 1MBit 0,669872 1,067308 1,298077 0,39744 0,23077 63,27 1,99 1 Remark 1: For further details please refer  Annex 1: Test results - CETECOM_TR17-1-0180901T11a-A1  The results were corrected in order to evaluate for worst-case result each time when average values are necessary for example average radiated emissions or similar  No correction necessary: Duty-Cycle > 98% CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 16 of 31 5.2. RF-Parameter – RF Power conducted 5.2.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  443 System CTC-FAR-EMI-  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS  683 FSU 26    spectr. analys.  489 ESU  120 FSEM  264 FSEK    power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  4.20 V DC (fully charged internal battery) otherwise  613 20dB Attenuator  Directional Coupler 1539R-10 Power meter  600 NRVD Power meter  266 NRV-Z31 Peak Power Sensor Supply voltage  230 V 50 Hz via public mains  5.2.2. Requirements: FCC  §15.247 (b) (3) + KDB 558074 D01 DTS Meas.Guidance v04 ANSI  C63.10-2013 Chapter 6.101 5.2.3. Reference: EUT antenna characteristics:  Directional Gain < 6 dBi (measured: difference between measured conducted and radiated eirp. power)  Directional Gain > 6 dBi (measured / applicant’s declaration) -> conducted power reduction necessary 5.2.4. EUT settings: For FHHS-systems hopping mode was switched-off so fixed three different channels could be measured. The EUT was instructed to send with maximum power (if adjustable) according applicants instructions. Different modulation characteristics have been checked, e.g. data rates which EUT can operate. 5.2.5. Measurement method: The measurement was performed in non-hopping transmission mode with the carrier set to lowest/middle and highest channel. The power was also checked for different data rates, modulation scheme or packet types if applicable. 5.2.6. Settings on Spectrum-Analyzer: Center Frequency Nominal channel frequency Span 8 MHz Resolution Bandwidth (RBW) 3 MHz > 20dB-Bandwidth of the signal Video Bandwidth (VBW) 3 times the resolution bandwidth = 10MHz Sweep time coupled Detector Peak, Max hold mode Sweep Mode Repetitive mode CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 17 of 31 5.2.7. Conducted measurement: Max. Peak Power  Applicant’s declared Maximum Directional ANT1 Peak Gain : 3.04 dBi Conducted Max Peak Power Measurements [dBm] Set-up no.: 2 Low channel = 0 Middle channel = 19 High channel = 78 Op-Mode: 1 (2402 MHz) (2440 MHz) (2480 MHz) Bluetooth LE Mode GFSK| 1 Mbps 0.12 0.29 0.39 Pattern Length:37 | PRBS9 Remark : Measurements results are only valid and compliant with power setting: +7 dBm Maximum Conducted value 0.39 dBm 0.00109 W Maximum antenna ANT1 gain 3.04 dBi Maximum e.i.r.p. value 3.43 dBm 0.00220 W FCC 15.247 Limit 30.00 dBm 1W CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 18 of 31 5.3. General Limit - Radiated field strength emissions below 30 MHz 5.3.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  347 Radio.lab.   receiver  377 ESCS30  001 ESS     spectr. analys.  584 FSU  120 FSEM  264 FSEK    antenna  574 BTA-L  021 EMCO6502  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix  378 RadiSense DC power  671 EA-3013S  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 Supply voltage  230 V 50 Hz via public mains  4.2 V DC (fully charged internal battery) 5.3.2. Requirements FCC  Part 15. Subpart C. §15.205 & §15.209  Part 15.247 (d) ANSI C63.10-2013 Frequency Field strength limit Distance Remarks [MHz] [μV/m] [dBμV/m] [m] 0.009 – 0.490 2400/f (kHz) 67.6 – 20Log(f) (kHz) 300 Correction factor used due to measurement distance of 3 m 0.490 – 1.705 24000/f (kHz) 87.6 – 20Log(f) (kHz) 30 Correction factor used due to measurement distance of 3 m 1.705 – 30 30 29.5 30 Correction factor used due to measurement distance of 3 m 5.3.3. Test condition and test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)%  9 – 150 kHz RBW/VBW = 200 Hz Scan step = 80 Hz Scan data  150 kHz – 30 MHz RBW/VBW = 9 kHz Scan step = 4 kHz  other: EMI-Receiver or Scan-Mode  6 dB EMI-Receiver Mode  3dB Spectrum analyser Mode Analyzer Settings Detector Peak (pre-measurement) and Quasi-PK/Average (final if applicable) Mode: Repetitive-Scan. max-hold Sweep-Time Coupled – calibrated display if continuous signal otherwise adapted to EUT’s individual transmission duty-cycle General measurement procedures Please see chapter “Test system set-up radiated magnetic field measurements below 30 MHz” 5.3.4. Radiated Field Strength Emissions – 9 kHz to 30 MHz Results Radiated Field Strength Emissions – 9 kHz to 30 MHz Temperature :+21 °C Technology: Bluetooth LE Modes TX-Fixed Channel (Modulated) Diagram Set- OP- Used detector Test Settings No. up mode Verdict (Remark 1) Modulation | Data Rate| Pattern Details | Test Channel no. no. PK AV QP GFSK | 1 Mbps | Pattern Length:37 | PRBS9 2.54 1 1    Pass Lowest Channel 0: 2402 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 2.55 1 1    Pass Middle Channel 19: 2440 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 2.56 1 1    Pass Highest Channel 39: 2480 MHz Remark 1: For further details please refer  Annex 1: Test results - CETECOM_TR17-1-0180901T11a-A1 Remark 2: Measurements results are only valid and compliant with power setting: +7 dBm CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 19 of 31 5.3.5. Correction factors due to reduced meas. distance (f< 30 MHz) The used correction factors when the measurement distance is reduced compared to regulatory measurement distance. are calculated according Extrapolation formulas valid for EUT’s with maximum dimension of 0.625xLambda. Formula 2+3+4 as presented in ANSI C63.10. Chapter 6.4.4 are used for the calculations of proper extrapolation factors. CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 20 of 31 5.4. General Limit - Radiated field strength emissions. 30 MHz - 1 GHz 5.4.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA receiver  377 ESCS30  001 ESS  489 ESU 40  620 ESU 26 spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix DC power  671 EA-3013S  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE Supply voltage  230 V 50 Hz via public mains  4.2 V DC (fully charged internal battery) 5.4.2. Requirements/Limits  Part 15 Subpart B. §15.109. class B FCC  Part 15 Subpart C. §15.209 @ frequencies defined in §15.205  Part 15.247 (d)  C63.4-2014 ANSI  C63.10-2013 Radiated emissions limits. 3 meters Frequency [MHz] QUASI Peak [µV/m] QUASI-Peak [dBµV/m] 30 - 88 100 40.0 Limit 88 - 216 150 43.5 216 - 960 200 46.0 above 960 500 54.0 5.4.3. Restricted bands of operation (FCC §15.205) MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 0.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.20725-4.20775 37.5-38.25 1645.5-1646.5 9.3-9.5 6.215-6.218 73-74.6 1660-1710 10.6-12.7 6.26775-6.26825 74.8-75.2 1718.8-1722.2 13.25-13.4 6.31175-6.31225 108-121.94 2200-2300 14.47-14.5 8.291-8.294 123-138 2310-2390 15.35-16.2 8.362-8.366 149.9-150.05 2483.5-2500 17.7-21.4 8.37625-8.38675 156.52475-156.52525 2690-2900 22.01-23.12 8.41425-8.41475 156.7-156.9 3260-3267 23.6-24.0 12.29-12.293 162.0125-167.17 3332-3339 31.2-31.8 12.51975-12.52025 167.72-173.2 3345.8-3358 36.43-36.5 12.57675-12.57725 240-285 3600-4400 -- 13.36-13.41 322-335.4 -- -- CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 21 of 31 5.4.4. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 0.8m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver Scan frequency range:  30 – 1000 MHz  other: (Analyzer) Settings Scan-Mode  6 dB EMI-Receiver Mode  3 dB spectrum analyser mode Detector Peak / Quasi-peak RBW/VBW 100 kHz/300 kHz Mode: Repetitive-Scan. max-hold Scan step 80 kHz Sweep-Time Coupled – calibrated display if continuous tx-signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for electric field measurement in the range 30 MHz to 1 GHz” 5.4.5. Radiated Field Strength Emissions – 30 MHz to 1 GHz Results Radiated Field Strength Emissions – 30 MHz to 1 GHz Temperature :+21 °C Technology: Bluetooth LE Modes TX-Fixed Channel (Modulated) Diagram Set- OP- Used detector Test Settings No. up mode Verdict (Remark 1) Modulation | Data Rate| Pattern Details | Test Channel no. no. PK AV QP GFSK | 1 Mbps | Pattern Length:37 | PRBS9 3.54 1 1    Pass Lowest Channel 0: 2402 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 3.55 1 1    Pass Middle Channel 19: 2440 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 3.56 1 1    Pass Highest Channel 39: 2480 MHz Remark 1: For further details please refer  Annex 1: Test results - CETECOM_TR17-1-0180901T11a-A1 Remark 2: Measurements results are only valid and compliant with power setting: +7 dBm CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 22 of 31 5.5. General Limit - Radiated emissions. above 1 GHz 5.5.1. Test location and equipment FAR test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU 40   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025  302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2  376 BBHA9120E  antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170  multimeter  341 Fluke 112      signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW DCpower car  611 E3632A  087 EA3013  354 NGPE 40  349  350 Car battery  battery Supply voltage  230 V 50 Hz via public mains  4.2 V DC (fully charged internal battery) 5.5.2. Requirements/Limits (CLASS B equipment)  Part 15 Subpart B. §15.109 class B FCC  Part 15 Subpart C. §15.209 for frequencies defined in §15.205  Part 15.247 (d)  C63.4-2014 ANSI  C63.10-2013 Limits Frequency AV AV Peak Peak [MHz] [µV/m] [dBµV/m] [µV/m] [dBµV/m] or [dBm/MHz] RSS-Gen.. Issue 500 54.0 5000 74.0 dBµV/m 4. §8.10 - Table 6 5.5.3. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 1.5m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Spectrum- Scan frequency range:  1 – 18 GHz  18 – 25 GHz  18 – 40 GHz  other: Analyzer Scan-Mode  6 dB EMI-Receiver Mode  3 dB Spectrum analyser Mode settings Detector Peak and Average RBW/VBW 1 MHz / 3 MHz Mode: Repetitive-Scan. max-hold Scan step 400 kHz Sweep-Time Coupled – calibrated display if CW signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for radiated electric field measurements above 1 GHz” CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 23 of 31 5.5.4. Radiated Field Strength Emissions – 1 GHz to 18 GHz Results Radiated Field Strength Emissions – 1 GHz to 18 GHz Temperature :+21 °C Technology: Bluetooth LE Modes TX-Fixed Channel (Modulated) Diagram Set- OP- Used detector Test Settings No. up mode Verdict (Remark 1) Modulation | Data Rate| Pattern Details | Test Channel no. no. PK AV QP GFSK | 1 Mbps | Pattern Length:37 | PRBS9 4.54 1 1    Pass Lowest Channel 0: 2402 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 4.55 1 1    Pass Middle Channel 19: 2440 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 4.56 1 1    Pass Highest Channel 39: 2480 MHz Remark 1: For further details please refer  Annex 1: Test results - CETECOM_TR17-1-0180901T11a-A1 Remark 2: Measurements results are only valid and compliant with power setting: +7 dBm 5.5.5. Radiated Field Strength Emissions – 18 GHz to 25 GHz Results Radiated Field Strength Emissions – 18 GHz to 25 GHz Temperature :+21 °C Technology: Bluetooth LE Modes TX-Fixed Channel (Modulated) Diagram Set- OP- Used detector Test Settings No. up mode Verdict (Remark 1) Modulation | Data Rate| Pattern Details | Test Channel no. no. PK AV QP GFSK | 1 Mbps | Pattern Length:37 | PRBS9 4.54a 1 1    Pass Lowest Channel 0: 2402 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 4.55a 1 1    Pass Middle Channel 19: 2440 MHz GFSK | 1 Mbps | Pattern Length:37 | PRBS9 4.56a 1 1    Pass Highest Channel 39: 2480 MHz Remark 1: For further details please refer  Annex 1: Test results - CETECOM_TR17-1-0180901T11a-A1 Remark 2: Measurements results are only valid and compliant with power setting: +7 dBm CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 24 of 31 5.6. RF-Parameter - Radiated Band Edge compliance measurements 5.6.1. Test location and equipment FAR test site  441 EMI SAR  348 EMI cond.  443 EMI FAR  347 Radio.lab.  337 OATS  spectr. analys.  584 FSU  120 FSEM  264 FSEK  489 ESU 40   antenna meas  574 BTA-L  289 CBL 6141  608 HL 562  549 HL025  302 BBHA9170  477 GPS antenna meas  123 HUF-Z2  132 HUF-Z3  030 HFH-Z2  376 BBHA9120E  antenna subst  071 HUF-Z2  020 EMCO3115  063 LP 3146  303 BBHA9170  multimeter  341 Fluke 112      signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW DCpower  611 E3632A  087 EA3013  354 NGPE 40  349 carbattery  350 Car battery  sSupply  230 V 50 Hz via public mains  4.2 V DC (fully charged internal battery) voltage 5.6.2. Requirements/Limits  Part 15 Subpart B. §15.109 class B FCC  Part 15 subpart C. §15.209 @ frequencies defined in §15.205  Part 15.247 (d) ANSI  C63.4-2009  C63.4-2014  C63.10-2009  C63.10-2013. Chapter 6.10.6 5.6.3. Test condition and measurement test set-up Signal ink to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 1.5m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% Spectrum- Scan frequency range:  1 – 18 GHz  18 – 25 GHz  18 – 40 GHz  other: see diagrams Analyzer Scan-Mode  6 dB EMI-Receiver Mode  3 dB Spectrum analyser Mode settings Detector Peak and Average RBW/VBW Left band-edge: 100kHz/300kHz Right band-edge: 1 MHz / 3 MHz Mode: Repetitive-Scan. max-hold Scan step 40kHz or 400 kHz Sweep-Time Coupled – calibrated display if CW signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for radiated electric field measurements above 1 GHz” for general measurements procedures in anechoic chamber. 5.6.4. Measurement Method For uncritical results where a measurement resolution bandwidth of 1MHz can clearly show the compliance without influencing the results. a field strength measurement was performed to show compliance. For critical results a Marker-Delta marker method was used for showing compliance to restricted bands. The method is according ANSI C63.10:2013. Chapter 6.10.6 “Marker-Delta method”.. The method consists of three independent steps: 1. Step: Prior to the measurement the fundamental radiated In-Band field strength was performed. The determined value is used as reference value. 2. Step: Second step consist of finding the relative attenuation between the fundamental emission and the maximum local out-of-band emission (within 2 MHz range around the band edge either on the band-edge directly or some modulation product if the level is greater than that on the band-edge) when measured with lower resolution bandwidth. 3. Step: The delta value recorded in step 2 will be subtracted from value recorded in step 1. thus giving the required field strength at the band-edge. This value must fulfil the requirements for radiated spurious emissions in restricted bands in FCC §15.205 with the general limits of FCC §15.209. 5.6.5. EUT settings The EUT was set in Hopping OFF mode with maximum power (if adjustable) according to applicants instructions. CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 25 of 31 5.6.6. Results: for non-restricted bands near-by 5.6.6.1. Non-restricted bands near-by - limits according FCC §15.247 Set-up No.: 1 Op. Mode: 1 Fundamental Value Peak-Value Remark: [dBuV/m] Channel Restricted at Band- Difference Limit Margin Diagram No. Average -Value + Verdict No. band ? Edge [dB] [dBc] [dB] Peak-Value Duty Cycle Data Rate | Power | Hopping ? Correction [dBuV/m] 9.57 0 NO 96,24 86,13 51,41 44,83 20,00 24,83 PASS LE Mode | GFSK | 1 Mbps |+7 dBm | Hopping OFF Remark 1: For further details please refer  Annex 1: Test results - CETECOM_TR17-1-0180901T11a-A1 Remark 2: Measurements results are only valid and compliant with power setting: +7 dBm 5.6.6.2. Restricted bands near-by §15.205 with limits accord. FCC §15.209 Set-up No.: 1 Op. Mode: 1 Fundamental Value Value at Band-Edge Limits Margin Remark: [dBuV/m] [dBuV/m] [dBuV/m] [dB] Channel Restricted Diagram No. Average - Verdict no. band ? Average -Value + Peak Value + Duty Peak Average Peak-Value Duty Cycle Peak Average Data Rate | Power | Hopping ? -Value Cycle -Value -Value Correction Correction 9.58 39 YES 98,058 97,392 58,11 48,79 74,00 54,00 15,89 5,21 PASS LE Mode | GFSK | 1 Mbps |+7 dBm | Hopping OFF Remark 1: For further details please refer  Annex 1: Test results - CETECOM_TR17-1-0180901T11a-A1 Remark 2: Measurements results are only valid and compliant with power setting: +7 dBm CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 26 of 31 5.7. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k. such that a confidence level of approximately 95% is achieved. For uncertainty determination. each component used in the concrete measurement set-up was taken in account and it’s contribution to the overall uncertainty according it’s statistical distribution calculated. Following table shows expectable uncertainties for each measurement type performed. Calculated uncertainty based on a RF-Measurement Reference Frequency range Remarks confidence level of 95% Conducted emissions 9 kHz - 150 kHz 4.0 dB CISPR 16-2-1 - (U CISPR) 150 kHz - 30 MHz 3.6 dB Radiated emissions 30 MHz - 1 GHz 4.2 dB CISPR 16-2-3 E-Field Enclosure 1 GHz - 18 GHz 5.1 dB Disturbance power CISPR 16-2-2 30 MHz - 300 MHz - - Substitution Power Output radiated - 30 MHz - 4 GHz 3.17 dB method Cel- Cel- Set-up No. BT1 W1 W2 -- C1 C2 Power Output conducted - 9 kHz - 12.75 GHz N/A 0.60 0.7 0.25 N/A -- - 12.75 - 26.5GHz N/A 0.82 -- N/A N/A -- Conducted emissions - 9 kHz - 2.8 GHz 0.70 N/A 0.70 N/A 0.69 -- N/A - not on RF-port 2.8 GHz - 12.75GHz 1.48 N/A 1.51 N/A 1.43 -- applicable 12.75 GHz - 18GHz 1.81 N/A 1.83 N/A 1.77 -- 18 GHz - 26.5GHz 1.83 N/A 1.85 N/A 1.79 -- 0.1272 ppm (Delta Marker) Frequency Occupied bandwidth - 9 kHz - 4 GHz error 1.0 dB Power - 0.1272 ppm (Delta Marker) Frequency Emission bandwidth 9 kHz - 4 GHz error - See above: 0.70 dB Power Frequency stability - 9 kHz - 20 GHz 0.0636 ppm - 150 kHz - 30 MHz 5.0 dB Magnetic Radiated emissions 30 MHz - 1 GHz 4.2 dB field - Enclosure 1 GHz - 20 GHz 3.17 dB E-field Substitution Table: measurement uncertainties. valid for conducted/radiated measurements CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 27 of 31 6. Abbreviations used in this report The abbreviations ANSI American National Standards Institute AV . AVG. CAV Average detector EIRP Equivalent isotropically radiated power. determined within a separate measurement EGPRS Enhanced General Packet Radio Service EUT Equipment Under Test FCC Federal Communications Commission. USA IC Industry Canada n.a. not applicable Op-Mode Operating mode of the equipment PK Peak RBW resolution bandwidth RF Radio frequency RSS Radio Standards Specification. Documents from Industry Canada Rx Receiver TCH Traffic channel Tx Transmitter QP Quasi peak detector VBW Video bandwidth ERP Effective radiated power 7. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS. Deutsche All laboratories and test sites of CETECOM GmbH. Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz. 3 m / 10 m (OATS) FCC. Federal Communications 487 Radiated Measurements 30 MHz to 1 GHz. 3 m (SAR) (MRA US-EU Commission 558 Radiated Measurements above 1 GHz. 3 m (FAR) 0003) Laboratory Division. USA 348 Mains Ports Conducted Interference Measurements 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz. 3 m / 10 m (OATS) 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz. 3 m (SAR) IC. Industry Canada Certification 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz. 3 m (SAR) and Engineering Bureau 558 3462D-3 Radiated Measurements above 1 GHz. 3 m (FAR) 487 R-2666 Radiated Measurements 30 MHz to 1 GHz. 3 m (SAR) VCCI. Voluntary Control Council 550 G-301 Radiated Measurements 1 GHz to 6 GHz. 3 m (SAR) for Interference by Information 348 C-2914 Mains Ports Conducted Interference Measurements Technology Equipment. Japan 348 T-1967 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site. SAR = Semi Anechoic Room. FAR = Fully Anechoic Room CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 28 of 31 8. Instruments and Ancillary TC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 8.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 9.15.00 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 9.15.00 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 607 Signal Generator SMR 20 832033/011 V1.25 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 Setup V03.26, Test programm component V03.02.20 670 Univ. Radio Communication Tester CMU 200 106833 µP1 =V8.50, Firmware = V.20 689 Vector Signal Generator SMU200 100970 02.20.360.142 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 29 of 31 8.1.2. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 001 EMI Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 16.05.2018 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 12 M - 15.05.2018 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 12 M - 17.05.2018 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 15.05.2019 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 30.05.2019 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 30.04.2018 030 Loop Antenna (H-field) HFH-Z2 879604/026 Rohde & Schwarz 36 M - 30.04.2018 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 15.05.2019 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 30.04.2018 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 30.04.2018 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 BOCONSULT 36 M - 30.05.2019 133 horn antenna 18 GHz (Meas 1) 3115 9012-3629 EMCO 36 M 1c 10.03.2020 134 horn antenna 18 GHz (Subst 2) 3115 9005-3414 EMCO 36 M - 10.03.2020 136 adjustable dipole antenna (Dipole 1) 3121C-DB4 9105-0697 EMCO 36 M - 30.04.2018 140 Signal Generator SMHU 831314/006 Rohde & Schwarz 24 M - 30.05.2018 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 30.05.2018 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 30.05.2018 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 30.05.2019 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 30.05.2018 266 Peak Power Sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 30.05.2018 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 12 M - 17.05.2018 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 14.03.2020 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 20.03.2020 331 Climatic Test Chamber -40/+180 Grad HC 4055 43146 Heraeus Vötsch 24 M - 30.10.2018 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 30.05.2018 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 17.05.2019 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 355 Power Meter URV 5 891310/027 Rohde & Schwarz 24 M - 30.05.2018 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 24.05.2019 371 Bluetooth Tester CBT32 100153 R&S 36 M - 30.05.2019 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 12 M - 17.05.2018 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 15.05.2018 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 18.05.2018 126.0604.0003.3.3.3.2 LUFFT Mess u. 405 Thermo-/Hygrometer OPUS 10 THI 24 M - 30.03.2019 2 Regeltechnik 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 24.05.2018 439 UltraLog-Antenna HL 562 100248 Rohde & Schwarz 36 M - 10.03.2020 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 16.06.2018 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 30.05.2018 CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 30 of 31 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 467 Digital Multimeter Fluke 112 89680306 Fluke USA 36 M - 30.04.2018 468 Digital Multimeter Fluke 112 90090455 Fluke USA 36 M - 30.04.2018 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 16.05.2019 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d System EMI field (SAR) ETS Lindgren / 487 System CTC NSA-Verification SAR-EMI - 24 M - 31.03.2019 NSA CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 18.05.2019 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- 503 band reject filter WRCG 824/849-814/859- SN 5 Wainwright pre-m 2 WRCA 800/960-02/40- 512 notch filter GSM 850 SN 24 Wainwrght 12 M 1c 30.06.2017 6EEK 517 relais switch matrix HF Relais Box Keithley SE 04 Keithley pre-m 2 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 18.05.2019 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 530 10 dB Broadband resistive power divider R 416110000 LOT 9828 - pre-m 2 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 30.03.2018 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 05.07.2018 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz 36/12 M - 31.07.2018 System CTC S-VSWR Verification SAR- System EMI Field SAR S- ETS 550 - 24 M - 30.03.2019 EMI VSWR Lindgren/CETECOM System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 08.08.2019 VSWR 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia 36/12 M - 31.03.2019 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz pre-m - 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz pre-m - 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 17.05.2019 601 medium-sensitivity diode sensor NRV-Z5 (Reserve) 8435323/003 Rohde & Schwarz 24 M - 15.05.2019 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 30.05.2018 617 Power Splitter/Combiner ZFSC-2-2-S+ S F987001108 Mini Circuits - 2 618 Power Splitter/Combiner 50PD-634 600994 JFW Industries USA - 2 619 Power Splitter/Combiner 50PD-634 600995 JFW Industries, USA - 3 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 16.05.2018 621 Step Attenuator 0-139 dB RSP 100017 Rohde & Schwarz pre-m 2 625 Generic Test Load USB Generic Test Load USB - CETECOM - 2 201.0999.9302.6.4.1.4 627 data logger OPUS 1 G. Lufft GmbH 24 M - 30.03.2019 3 634 Spectrum Analyzer FSM (HF-Unit) 826188/010 Rohde & Schwarz pre-m 2 HDMI cable with Ethernet 637 High Speed HDMI with Ethernet 1m - KogiLink - 2 1m 638 HDMI Kabel with Ethernet 1,5 m flach HDMI cable with Ethernet - Reichelt - 2 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 641 HDMI cable with Ethernet Certified HDMI cable with - PureLink - 2 642 Wideband Radio Communication Tester CMW 500 126089 Rohde&Schwarz 12 M - 24.05.2018 644 Amplifierer ZX60-2534M+ SN865701299 Mini-Circuits - - 670 Univ. Radio Communication Tester CMU 200 106833 Rohde & Schwarz 24 M - 30.05.2018 671 DC-power supply 0-5 A EA-3013S - Elektro Automatik pre-m 2 678 Power Meter NRP 101638 Rohde&Schwarz pre-m - 683 Spectrum Analyzer FSU 26 200571 Rohde & Schwarz 12 M - 17.05.2018 Narda Safety Test 686 Field Analyzer EHP-200A 160WX30702 24 M - 29.03.2019 Solutions 687 Signal Generator SMF 100A 102073 Rohde&Schwarz 12 M - 17.05.2018 688 Pre Amp JS-18004000-40-8P 1750117 Miteq pre-m - 690 Spectrum Analyzer FSU 100302/026 Rohde&Schwarz 12 M - 16.05.2018 691 OSP120 Base Unit OSP120 101183 Rohde & Schwarz 12 M - 22.05.2018 692 Bluetooth Tester CBT 32 100236 Rohde & Schwarz 36 M - 29.05.2020 697 Power Splitter ZN4PD-642W-S+ 165001445 Mini-Circuits - 2 MA 4010-KT080-XPET- MA4170-KT100- 703 INNCO Antennen Mast INNCO pre-m - ZSS3 XPET- CO3000/933/3841051 704 INNCON Controller CO 3000-4port INNCO Systems GmBh pre-m - 6/L 711 Harmonic Mixer 90 GHz - 140GHz RPG FS-Z140 101004 RPG 12 M - 22.02.2018 712 Harmonic Mixer 75 GHz - 110GHz FS-Z110 101468 Rohde & Schwarz 12 M - 22.02.2018 713 Harmonic Mixer, 50 GHz - 75GHz FS-Z75 101022 Rohde & Schwarz 12 M - 22.05.2018 714 Signal Analyzer 67GHz FSW67 104023 Rohde & Schwarz 24 M - 03.03.2019 RPG Radiometer 715 Harmonic Mixer, 140 GHz - 220GHz FS-Z220 101009 12 M - 03.08.2018 Physics 716 Harmonic Mixer 220 GHz to 325 GHZ FS-Z325 101005 RPG Radiometer Physics 12 M - 13.02.2018 747 Spectrum Analyzer FSU 26 200152 Rohde & Schwarz 12 M - 18.05.2018 CETECOM_TR17-1-0180901T11a

Test Report 17-1-0180901T11a, Page 31 of 31 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 748 Pickett-Potter Horn Antenna FH-PP 4060 010001 Radiometer Physiscs - - 749 Pickett-potter Horn Antenna FH-PP 60-90 010003 Radiometer Physics - - 750 Pickett-Potter Horn Antenna FH-PP 140-220 010011 Radiometer Physics - - 8.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months. between this every 12 months internal validation 36/12 M Calibration every 36 months. between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration 9. Versions of test reports (change history) Version Applied changes Date of release -- Inital release 2017-12-27 -- -- -- -- -- -- CETECOM_TR17-1-0180901T11a


Document Created: 2018-01-30 00:39:56
Document Modified: 2018-01-30 00:39:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC