Test report

FCC ID: U4GFX3P

Test Report

Download: PDF
FCCID_2382521

FCC Measurement/Technical Report on WLAN / Bluetooth transceiver in Mobile Handheld Computer Datalogic Falcon X3+ FCC ID: U4GFX3P Report Reference: MDE_DATA_1405_FCCi_Rev1 Test Laboratory: Borsigstrasse 11 Germany 7Layers AG 40880 Ratingen Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7 layers AG Aufsichtsratsvorsitzender Registergericht registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Peter Mertel USt-IdNr  VAT No.: Phone: +49 (0) 2102 749 0 Vorstand Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. H.-J. Meckelburg TAX No. 147/5869/0385 www.7Layers.com Dr. H. Ansorge

Table of Contents 0 Applied Standards and Test Summary 3 0.1 Technical Report Summary 3 0.2 FCC and IC Correlation Table 4 0.3 Measurement Summary 5 1 Administrative Data 7 1.1 Testing Laboratory 7 1.2 Project Data 7 1.3 Applicant Data 7 1.4 Manufacturer Data 7 2 Test object Data 8 2.1 General EUT Description 8 2.2 EUT Main components 9 2.3 Ancillary Equipment 9 2.4 Auxiliary Equipment 9 2.5 EUT Setups 9 2.6 Operating Modes 10 2.7 Special software used for testing 11 2.8 Product labelling 11 3 Test Results 12 3.1 Spurious radiated emissions 12 3.2 Band edge compliance 18 4 Test Equipment 21 5 Photo Report 32 6 Setup Drawings 32 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 2 of 32

0 Applied Standards and Test Summary 0.1 Technical Report Summary Type of Authorization Certification for an Intentional Radiator (Digital Device / Spread Spectrum). Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 and 15 (10-1-13 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart C – Intentional Radiators § 15.201 Equipment authorization requirement § 15.207 Conducted limits § 15.209 Radiated emission limits; general requirements § 15.247 Operation within the bands 902-928 MHz, 2400-2483.5 MHz Note: The tests were selected and performed with reference to the FCC Public Notice “Guidance for Performing Compliance Measurements on Digital Transmission Systems (DTS)Operating Under §15.247, 558074 D01 DTS Meas Guidance v03r02, 2014-06-05”. Instead of applying ANSI C63.4–1992 which is referenced in the FCC Public Note, the newer ANSI C63.4–2009 is applied. Summary Test Results: The EUT complied with all performed tests as listed in chapter 0.3 Measurement Summary. Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 3 of 32

0.2 FCC and IC Correlation Table Correlation of measurement requirements for DTS devices (e.g. WLAN 2.4/5 GHz) equipment The following tables show the correlation of measurement requirements for DTS (e.g. WLAN) equipment and Information Technology Equipment (ITE) from FCC and IC standards. DTS equipment Measurement FCC reference IC reference Conducted emissions on § 15.207 RSS-Gen Issue 3: 7.2.4 AC Mains Occupied bandwidth § 15.247 (a) (2) RSS-210 Issue 8: A8.2 (a) Peak power output § 15.247 (b) (3), (4) RSS-210 Issue 8: A8.4 (4) Spurious RF conducted § 15.247 (d) RSS-Gen Issue 3: 6; emissions RSS-210 Issue 8: A8.5 Spurious radiated emissions § 15.247 (d); RSS-Gen Issue 3: 6; § 15.209 (a) RSS-210 Issue 8: A8.5 Band edge compliance § 15.247 (d) RSS-210 Issue 8: A8.5 Power density § 15.247 (e) RSS-210 Issue 8: A8.2 (b) Antenna requirement § 15.203 / 15.204 RSS-Gen Issue 3: 7.1.2 Receiver spurious emissions – RSS-210 Issue 8: 2.3 RSS Gen Issue 3: 6 *) *) Receivers which are part of Transceivers are exempted with respect to Notice 2012-DRS0126. Information Technology Equipment (ITE) Measurement FCC reference IC reference Conducted emissions on § 15.107 ICES-003 Issue 5: 6.1 AC Mains Spurious Radiated Emissions § 15.109 ICES-003 Issue 5: 6.2 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 4 of 32

0.3 Measurement Summary FCC Part 15, Subpart C § 15.207 Conducted emissions (AC power line) The measurement was performed according to ANSI C63.4 2009 OP-Mode Setup Port Final Result - - AC port N/A FCC Part 15, Subpart C § 15.247 (a) (1) Occupied bandwidth The measurement was performed according to FCC § 15.31 10-1-13 Edition OP-Mode Setup Port Final Result op-mode 1b Setup_01 Temp.ant.connector Not performed FCC Part 15, Subpart C § 15.247 (b) (1) Peak power output The measurement was performed according to FCC § 15.31 10-1-13 Edition OP-Mode Setup Port Final Result - - Temp.ant.connector Not performed FCC Part 15, Subpart C § 15.247 (d), § 15.35 (b), § 15.207 Spurious conducted emissions The measurement was performed according to ANSI C63.4 2009 OP-Mode Setup Port Final Result - - Temp.ant.connector Not performed FCC Part 15, Subpart C § 15.247 (d), § 15.35 (b), § 15.209 Spurious radiated emissions The measurement was performed according to ANSI C63.4 2009 OP-Mode Setup Port Final Result op-mode 1b Setup_01 Enclosure passed op-mode 2b Setup_01 Enclosure passed op-mode 3b Setup_01 Enclosure passed op-mode 1g Setup_01 Enclosure passed op-mode 2g Setup_01 Enclosure passed op-mode 3g Setup_01 Enclosure passed op-mode 1n Setup_01 Enclosure passed op-mode 2n Setup_01 Enclosure passed op-mode 3n Setup_01 Enclosure passed op-mode BT1-BDR Setup_01 Enclosure passed op-mode BT2-BDR Setup_01 Enclosure passed op-mode BT3-BDR Setup_01 Enclosure passed op-mode BT1-ED1 Setup_01 Enclosure passed op-mode BT2-ED1 Setup_01 Enclosure passed op-mode BT3-ED1 Setup_01 Enclosure passed op-mode BT1-ED2 Setup_01 Enclosure passed op-mode BT2-ED2 Setup_01 Enclosure passed op-mode BT3-ED2 Setup_01 Enclosure passed Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 5 of 32

FCC Part 15, Subpart C § 15.247 (d) Band edge compliance The measurement was performed according to FCC § 15.31 / 10-1-13 Edition / ANSI C63.4 2009 OP-Mode Setup Port Final Result op-mode 3b Setup_01 Enclosure passed op-mode 3g Setup_01 Enclosure passed op-mode 3n Setup_01 Enclosure passed op-mode BT3-BDR Setup_01 Enclosure passed op-mode BT3-ED1 Setup_01 Enclosure passed op-mode BT3-ED2 Setup_01 Enclosure passed FCC Part 15, Subpart C § 15.247 (e) Power density The measurement was performed according to FCC § 15.31 10-1-13 Edition OP-Mode Setup Port Final Result - - Temp.ant.connector Not performed N/A not applicable (the EUT is powered by DC) Responsible for Responsible Accreditation Scope: for Test Report: 0.4 Revision History Report version control Version Release date Change Description Version validity FCCi 2014-08-13 Initial version Not valid FCCi_Rev1 2014-08-26 Editorial Change after TCB review: valid Bluetooth transceiver added on frontpage and in chapter 2.2 EUT description Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 6 of 32

1 Administrative Data 1.1 Testing Laboratory Company Name: 7 Layers AG Address Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716 . The test facility is also accredited by the following accreditation organisation: Laboratory accreditation no.: DAkkS D-PL-12140-01-01 Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Robert Machulec Dipl.-Ing. Thomas Hoell Dipl.-Ing. Andreas Petz Dipl.-Ing. Marco Kullik Report Template Version: 2014-08-26 1.2 Project Data Responsible for testing and report: Dipl.-Ing. Marco Kullik Date of Test(s): 2014-06-03 to 2014-07-21 Date of Report: 2014-08-13 1.3 Applicant Data Company Name: Datalogic ADC s.r.l. Address: Via S. Vitalino, 13 40012 Lippo di Calderara di Reno, Bologna Italy Contact Person: Mr. Eucarpio Guarisco 1.4 Manufacturer Data Company Name: Please see applicant data Address: Contact Person: Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 7 of 32

2 Test object Data 2.1 General EUT Description Equipment under Test: IEEE 802.11a/b/g/n WLAN & BT transceiver Type Designation: Datalogic FALCON X3+ Kind of Device: Mobile Handheld Computer (optional) Voltage Type: DC Voltage Level: 5.0 V Tested Modulation Type: WLAN: DBPSK; OFDM:BPSK; OFDM: 64-QAM BT: GFSK, π/4-DQPSK, 8-DPSK General product description: The EUT is a mobile handheld computer. It runs with Windows Mobile 6 CE. Specific product description for the EUT: The EUT is a dual band WLAN (802.11 a/b/g/n, 2.4 and 5 GHz) and Bluetooth module with one joint antenna connector for WLAN and Bluetooth. In IEEE 802.11n mode it only supports 20 MHz bandwidth channels (MCS7), providing 72.2 Mbit/s transfer data rates respectively. The object of this test report is the BT and WLAN transceiver, consequently switched on the IEEE 802.11 b/g/n modes, working in the 2.4 band. In IEEE 802.11n mode, it was tested with 20 MHz channel bandwidth. The EUT provides the following ports: Ports Enclosure System-port The main components of the EUT are listed and described in Chapter 2.2 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 8 of 32

2.2 EUT Main components Type, S/N, Short Descriptions etc. used in this Test Report Short Equipment Type Serial No. HW Status SW Status Description under Test Designation EUT A WLAN & BT FALCON X3+ 5M P/N: 1.88 and (Code: transceiver 945250051 subsequent DE1006002aa01) Remark: EUT A is equipped with two dual-band integral antennas (2.4 & 5 GHz) frequency band with a maximal antenna gain of 4.2 dBi in the 4.9 – 5.9 GHz frequency range. EUT A WLAN & BT FALCON X3+ 9I P/N: 1.88 and (Code: transceiver 945250055 subsequent DE1006002ab01) Remark: EUT A is equipped with two dual-band integral antennas (2.4 & 5 GHz) frequency band with a maximal antenna gain of 4.2 dBi in the 4.9 – 5.9 GHz frequency range. NOTE: The short description used to simplify the identification of the EUT in this test report. 2.3 Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment, which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Short Equipment under Type Designation Serial No. HW SW Description Test Status Status - – – – – – 2.4 Auxiliary Equipment For the purposes of this test report, auxiliary equipment is defined as equipment, which is used temporarily to enable operational and control features especially used for the tests of the EUT, which is not used during normal operation or equipment that is used during the tests in combination with the EUT but is not subject of this test report. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Auxiliary Equipment can influence the test results. Short Equipment under Type Designation Serial No. HW SW Description Test Status Status - – – – – – 2.5 EUT Setups This chapter describes the combination of EUTs and equipment used for testing. The rationale for selecting the EUTs, ancillary and auxiliary equipment and interconnecting cables, is to test a representative configuration meeting the requirements of the referenced standards. Setup Combination of EUTs Description and Rationale Setup_01 EUT A setup for radiated radio measurements Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 9 of 32

2.6 Operating Modes This chapter describes the operating modes of the EUTs used for testing. 2.6.1 Test Channels Band: WLAN 2.4 GHz ISM 900 MHz 902 - 928 MHz 2400 - 2483.5 MHz Bottom Middle Top Bottom Middle Top 1 6 11 2412 2437 2462 Band: BT 2.4 GHz ISM 900 MHz 902 - 928 MHz 2400 - 2483.5 MHz Bottom Middle Top Bottom Middle Top 0 39 78 2402 2441 2480 2.6.2 Datarates SISO: WLAN b-Mode; 20 MHz; 6 Mbit/s WLAN g-Mode; 20 MHz; 11 Mbit/s WLAN n-Mode; 20 MHz; 72.2 Mbit/s BT 1-DH1; 1 Mbit/s BT 2-DH1; 2 Mbit/s BT 3-DH1; 3 Mbit/s WLAN: Data rate / frequency 2412 2437 2462 b-mode, 6 Mbit/s 1b 2b 3b g-mode, 11 Mbit/s 1g 2g 3g n-Mode, 72.2 Mbit/s (MCS7) 1n 2n 3n BT: Data rate / frequency 2402 2441 2480 BT 1-DH1; 1 Mbit/s BT1-BDR BT2-BDR BT3-BDR BT 2-DH1; 2 Mbit/s BT1-ED1 BT2-ED1 BT3-ED1 BT 3-DH1; 3 Mbit/s BT1-ED2 BT2-ED2 BT3-ED2 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 10 of 32

2.7 Special software used for testing The Windows program “SRU” is used to control the WLAN module. 2.8 Product labelling 2.8.1 FCC ID label Please refer to the documentation of the applicant. 2.8.2 Location of the label on the EUT Please refer to the documentation of the applicant. Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 11 of 32

3 Test Results 3.1 Spurious radiated emissions Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.4 3.1.1 Test Description The test set-up was made in accordance to the general provisions of ANSI C63.4 in a typical installation configuration. The Equipment Under Test (EUT) was set up on a non- conductive table 1.0 x 2.0 m² in the semi-anechoic chamber. The influence of the EUT support table that is used between 30–1000 MHz was evaluated. The measurement procedure is implemented into the EMI test software ES-K1 from R&S. Exploratory tests are performed at 3 orthogonal axes to determine the worst-case orientation of a body-worn or handheld EUT. The final test on all kind of EUTs is performed at 2 axes. A pre-check is performed while the EUT is powered from a DC power sourse. 1. Measurement up to 30 MHz The Loop antenna HFH2-Z2 is used. Step 1: pre measurement - Anechoic chamber - Antenna distance: 10 m - Detector: Peak-Maxhold - Frequency range: 0.009 - 0.15 MHz and 0.15 – 30 MHz - Frequency steps: 0.1 kHz and 5 kHz - IF–Bandwidth: 0.2 kHz and 10 kHz - Measuring time / Frequency step: 100 ms Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: final measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is to find the maximum emission level. - Open area test side - Antenna distance: according to the Standard - Detector: Quasi-Peak - Frequency range: 0.009 – 30 MHz - Frequency steps: measurement at frequencies detected in step 1 - IF–Bandwidth: 0.2 - 10 kHz - Measuring time / Frequency step: 100 ms Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 12 of 32

2. Measurement above 30 MHz and up to 1 GHz Step 1: Preliminary scan This is a preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Antenna distance: 3 m - Detector: Peak-Maxhold - Frequency range: 30 – 1000 MHz - Frequency steps: 60 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 µs - Turntable angle range: –180° to 180° - Turntable step size: 90° - Height variation range: 1 – 3 m - Height variation step size: 2 m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: second measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is, to find out the approximate turntable angle and antenna height for each frequency. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: –180° to 180° - Turntable step size: 45° - Height variation range: 1 – 4 m - Height variation step size: 0.5 m - Polarisation: horizontal + vertical After this step, the EMI test system has determined the following values for each frequency (of step 1): - Frequency - Azimuth value (of turntable) - Antenna height The last two values have now the following accuracy: - Azimuth value (of turntable): 45° - Antenna height: 0.5 m Step 3: final measurement In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency, which was determined the turntable azimuth and antenna height will be adjusted. The turntable azimuth will slowly vary by ± 22.5° around this value. During this action, the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position, the antenna height will also slowly vary by ± 25 cm around the antenna height determined. During this action, the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100 ms - Turntable angle range: ± 22.5 ° around the determined value - Height variation range: ± 25 cm around the determined value Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 13 of 32

Step 4: final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak (< 1 GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1 s After the measurement a plot will be generated which contains a diagram with the results of the preliminary scan and a chart with the frequencies and values of the results of the final measurement. 3. Measurement above 1 GHz The following modifications apply to the measurement procedure for the frequency range above 1 GHz: The Equipment Under Test (EUT) was set up on a non-conductive support at 1.4 m height in the fully-anechoic chamber. The measurement distance was reduced to 1 m. The results were extrapolated by the extrapolation factor of 20 dB/decade (inverse linear-distance for field strength measurements, inverse linear-distance squared for the power reference level measurements). Due to the fact, that in this frequency range a double-ridged wave guided horn antenna (up to 18 GHz) and a horn antenna (18–25 GHz) are used, the steps 2-4 are omitted. Step 1 was performed with one height of the receiving antenna only. EMI receiver settings: - Detector: Peak, Average - IF Bandwidth = 1 MHz For the data rate in mode n the test is performed as worst-case-check in order to verify that emissions have a comparable level as found at modes b and g. Typically, the measurement is performed in the frequency range 1 to 8 GHz but it depends on the emissions found during the test for the modes b and g. Please refer to the results for the used frequency range. 3.1.2 Test Requirements / Limits FCC Part 15, Subpart C, §15.247 (e) For digitally modulated systems, the peak power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. … The same method of determining the conducted output power shall be used to determine the power spectral density. Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 14 of 32

3.1.3 Test Requirements / Limits FCC Part 15, Subpart C, §15.247 (d) ... In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). FCC Part 15, Subpart C, §15.209, Radiated Emission Limits Measurement Calculated Limits(dBµV/m Frequency in MHz Limit (µV/m) Limits(dBµV/m @10m) distance (m) @10m) 0.009 – 0.49 2400/F(kHz) 300 59.1 dB (48.5 – 13.8) + 30 dB 78.5 – 43.8 0.49 – 1.705 24000/F(kHz) 30 19.1 dB (48.9 – 23.0) + 10 dB 58.9 – 33.0 1.705 – 30 30 30 19.1 dB 29.5 + 10 dB 39.5 Measurement Frequency in MHz Limit (µV/m) Limit (dBµV/m) distance (m) 30 – 88 100 3 40.0 88 – 216 150 3 43.5 216 – 960 200 3 46.0 above 960 500 3 54.0 §15.35(b) ..., there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit.... Used conversion factor: Limit (dBµV/m) = 20 log (Limit (µV/m)/1µV/m) Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 15 of 32

3.1.4 Test Protocol Temperature: 23–27 °C Air Pressure: 997-1011 hPa Humidity: 33–50 % WLAN b-Mode; 20 MHz; 6 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Type 1 2412 4824.0 47.2 AV 1000 54.0 6.8 RB 6 2437 4874.0 42.6 AV 1000 54.0 11.4 RB 11 2462 2384.0 40.4 AV 1000 54.0 13.6 RB 11 2462 4924.0 39.1 AV 1000 54.0 14.9 RB BT 1-DH1; 1 Mbit /s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBm] [dB] Type - - - - - - - Note: No (further) spurious emissions in the range 20 dB below the limit found. The results of the pre-test with peak detector have been similar for all three transmit frequencies in the frequency range 30–1000 MHz and independent from the transmit frequency. Therefore the final test applying the QP-(quasi-peak-)detector was perfomed only for one transmit frequency. WLAN g-Mode; 20 MHz; 11 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Type 1 2412 2389.0 43.0 AV 1000 54.0 11.0 RB WLAN n-Mode; 20 MHz; 72.2 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Type 1 2412 2390.0 63.1 PEAK 1000 74.0 10.9 RB 1 2412 2390.0 45.6 AV 1000 54.0 8.4 RB Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 16 of 32

BT 2-DH1; 2 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBm] [dB] Type - - - - - - - BT 3-DH1; 3 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBm] [dB] Type - - - - - - - Note: No (further) spurious emissions in the range 20 dB below the limit found. The measurement was performed from 1 GHz up to 8 GHz because at pre-measurements no significant spurious emissions have been found outside this frequency range. Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 17 of 32

3.2 Band edge compliance Standard FCC Part 15, Subpart C The test was performed according to: ANSI C63.4–2009, FCC §15.31 3.2.1 Test Description The procedure to show compliance with the band edge requirement is divided into two measurements: 1. Show compliance of the lower and higher band edge by a conducted measurement. For the conducted measurement, the Equipment Under Test (EUT) is placed in a shielded room. For the lower band edge the EUT is set to transmit as follows: For a WLAN transmitter working in the 2.4 GHz band on lowest channel: CH1 = 2412 MHz / CH3 = 2422 MHz for a channel bandwidth of 20 / 40 MHz. The lower band edge is 2400 MHz for 2.4 GHz band transmitter. For the higher band edge the EUT is set to transmit as follows: For a WLAN transmitter working in the 2.4 GHz band on highest channel: CH11 = 2462 MHz or CH13 = 2472 MHz / CH11= 2462 MHz for a channel bandwidth of 20 / 40 MHz. The higher band edge is 2483.5 MHz for a 2.4 GHz band transmitter. Analyzer settings for conducted measurement: - Detector: Peak - RBW / VBW = 100 / 300 kHz 2. Showing compliance of the higher band edge falls in to restricted bands by a radiated measurement. The radiated emissions measurements are performed in a typical installation configuration inside the fully anechoic chamber using a horn antenna at 1 m distance. EMI receiver settings for radiated measurement: - Detector: Peak, Average - IF Bandwidth = 1 MHz 3.2.2 Test Requirements / Limits FCC Part 15.247 (d) “In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. ... If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in Section 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)).” Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 18 of 32

For the conducted measurement the RF power at the band edge shall be “at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power...” For the radiated measurement of the higher band edge connected to a restricted band the limit is “specified in Section 15.209(a)”. 3.2.3 Test Protocol 3.2.3.1 Radiated measurement, higher band edge Temperature: 23–27 °C Air Pressure: 997-1011 hPa Humidity: 33–50 % WLAN b-Mode; 20 MHz; 6 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Type 11 2462 2483.5 51.6 PEAK 1000 74.0 22.4 BE 11 2462 2483.5 40.9 AV 1000 54.0 13.1 BE WLAN g-Mode; 20 MHz; 11 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBm] [dB] Type 11 2462 2483.5 63.1 PEAK 1000 74.0 10.9 BE 11 2462 2483.5 44.5 AV 1000 54.0 9.5 BE WLAN n-Mode; 20 MHz; 72.2 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBm] [dB] Type 11 2462 2483.5 63.8 PEAK 1000 74.0 10.2 BE 11 2462 2483.5 45.6 AV 1000 54.0 8.4 BE Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 19 of 32

BT 1-DH1; 1 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Type 78 2462 2483.5 49.9 PEAK 1000 74.0 24.1 BE 78 2462 2483.5 37.6 AV 1000 54.0 16.4 BE BT 2-DH1; 2 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Type 78 2462 2483.5 49.5 PEAK 1000 74.0 24.5 BE 78 2462 2483.5 37.7 AV 1000 54.0 16.3 BE BT 3-DH1; 3 Mbit/s Channel Margin Center Spurious to Ch. Frequency Frequency Level RBW Limit Limit Limit No. [MHz] [MHz] [dBm] Detector [kHz] [dBµV/m] [dB] Type 78 2462 2483.5 50.0 PEAK 1000 74.0 24.0 BE 78 2462 2483.5 37.7 AV 1000 54.0 16.3 BE 3.2.3.2 Measurement Plot (showing the highest value, “worst case”) M ar k er : 2. 4835 G Hz 63. 81 d Bµ V/ m De lt a M k : 0 Hz - 18. 17 dB L e v e l [ d Bµ V/ m ] 80 70 60 50 40 30 20 10 0 2. 48G 2. 485G 2. 49G 2. 495G 2. 5G Fr e q u e n c y [ Hz ] M ES DA T _ 1 4 0 5 _ 039_pr e PK M ES DA T _ 1 4 0 5 _ 039_pr e AV LI M F CC 1 5 . 2 0 9 3m F ie ld St r e n g t h A V L im it LI M F CC 1 5 . 2 0 9 3m Pe a k F ie ld St r e n g t h Q - Pe a k L im it Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 20 of 32

4 Test Equipment List of Used Test Equipment The calibration, hardware and software states are shown for the testing period. Test Equipment Anechoic Chamber Lab ID: Lab 2 Manufacturer: Frankonia Description: Anechoic Chamber for radiated testing Type: 10.58x6.38x6.00 m³ Calibration Details Last Execution Next Exec. NSA (FCC) 2014/01/09 2017/01/09 Single Devices for Anechoic Chamber Single Device Name Type Serial Number Manufacturer Air compressor none - Atlas Copco Anechoic Chamber 10.58 x 6.38 x 6.00 m³ none Frankonia Calibration Details Last Execution Next Exec. FCC listing 96716 3m Part15/18 2014/01/09 2017/01/08 Controller Maturo MCU 961208 Maturo GmbH EMC camera CE-CAM/1 - CE-SYS EMC camera Nr.2 CCD-400E 0005033 Mitsubishi Filter ISDN B84312-C110-E1 Siemens&Matsushita Filter Universal 1A BB4312-C30-H3 - Siemens&Matsushita Test Equipment Auxiliary Equipment for Conducted emissions Lab ID: Lab 1 Manufacturer: Rohde & Schwarz GmbH & Co.KG Description: EMI Conducted Auxiliary Equipment Single Devices for Auxiliary Equipment for Conducted emissions Single Device Name Type Serial Number Manufacturer AC Power Source Chroma 6404 64040001304 Chroma ATE INC. Cable "LISN to ESI" RG214 W18.03+W48.03 Huber&Suhner Impedance Stabilization ISN T800 36159 Teseq GmbH Network Calibration Details Last Execution Next Exec. Standard Calibration 2014/02/06 2016/02/28 Impedance Stabilization ISN/CDN ENY41 100002 Rohde & Schwarz GmbH & Co. Network, Coupling KG Decoupling Network Calibration Details Last Execution Next Exec. Standard calibration 2013/03/01 2015/03/31 Impedance Stabilization ISN/CDN ST08 36292 Teseq GmbH Network, Coupling Decoupling Network Calibration Details Last Execution Next Exec. Standard calibration 2014/01/10 2016/01/31 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 21 of 32

Single Devices for Auxiliary Equipment for Conducted emissions (continued) Single Device Name Type Serial Number Manufacturer Impedance Stabilization ISN/CDN T8-Cat6 32187 Teseq GmbH Network, Coupling Decoupling Network Calibration Details Last Execution Next Exec. Standard Calibration 2014/01/08 2016/01/31 One-Line V-Network ESH 3-Z6 100489 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. standard calibration 2014/06/18 2017/11/30 One-Line V-Network ESH 3-Z6 100570 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2013/11/25 2016/11/24 Two-Line V-Network ESH 3-Z5 828304/029 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standart Calibration 2013/03/01 2015/02/28 Two-Line V-Network ESH 3-Z5 829996/002 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2013/03/01 2015/02/28 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 22 of 32

Test Equipment Auxiliary Equipment for Radiated emissions Lab ID: Lab 2 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Auxiliary Equipment for Radiated emissions Single Device Name Type Serial Number Manufacturer Antenna mast AM 4.0 AM4.0/180/119205 Maturo GmbH 13 Biconical Broadband SBA 9119 9119-005 Schwarzbeck Antenna Biconical dipole VUBA 9117 9117-108 Schwarzbeck Calibration Details Last Execution Next Exec. Standard Calibration 2012/01/18 2015/01/17 Broadband Amplifier JS4-18002600-32-5P 849785 Miteq 18MHz-26GHz Broadband Amplifier AFS4-01000400-1Q-10P-4 - Miteq 1GHz-4GHz Broadband Amplifier JS4-00101800-35-5P 896037 Miteq 30MHz-18GHz Cable "ESI to EMI EcoFlex10 W18.01-2+W38.01- Kabel Kusch Antenna" 2 Cable "ESI to Horn UFB311A+UFB293C W18.02-2+W38.02- Rosenberger Micro-Coax Antenna" 2 Double-ridged horn HF 906 357357/001 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/05/18 2015/05/17 Double-ridged horn HF 906 357357/002 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/06/26 2015/06/25 High Pass Filter 4HC1600/12750-1.5-KK 9942011 Trilithic High Pass Filter 5HC2700/12750-1.5-KK 9942012 Trilithic High Pass Filter 5HC3500/12750-1.2-KK 200035008 Trilithic High Pass Filter WHKX 7.0/18G-8SS 09 Wainwright Horn Antenna BBHA 9170 Schwarzbeck 15-26 GHz BBHA 9170 Log.-per. Antenna HL 562 Ultralog 100609 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/12/18 2015/12/17 Log.-per. Antenna HL 562 Ultralog 830547/003 Rohde & Schwarz GmbH & Co. KG Loop Antenna HFH2-Z2 829324/006 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2011/10/27 2014/10/26 Pyramidal Horn Antenna 3160-09 00083069 EMCO Elektronik GmbH 26,5 GHz Pyramidal Horn Antenna 3160-10 00086675 EMCO Elektronik GmbH 40 GHz Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 23 of 32

Single Devices for Auxiliary Equipment for Radiated emissions (continued) Single Device Name Type Serial Number Manufacturer Tilt device Maturo Antrieb TD1.5-10kg TD1.5- Maturo GmbH (Rohacell) 10kg/024/3790709 Test Equipment Auxiliary Test Equipment Lab ID: Lab 2, Lab 3 Manufacturer: see single devices Description: Single Devices for various Test Equipment Type: various Serial Number: none Single Devices for Auxiliary Test Equipment Single Device Name Type Serial Number Manufacturer AC Power Source Chroma 6404 64040001304 Chroma ATE INC. Broadband Power Divider 1506A / 93459 LM390 Weinschel Associates N (Aux) Broadband Power Divider WA1515 A855 Weinschel Associates SMA Digital Multimeter 03 Fluke 177 86670383 Fluke Europe B.V. (Multimeter) Calibration Details Last Execution Next Exec. Customized calibration 2013/12/04 2015/12/03 Fibre optic link Satellite FO RS232 Link 181-018 Pontis (Aux) Fibre optic link FO RS232 Link 182-018 Pontis Transceiver (Aux) Isolating Transformer LTS 604 1888 Thalheimer Transformatorenwerke GmbH Notch Filter Ultra Stable WRCA800/960-6EEK 24 Wainwright (Aux) Signal Analyzer FSV30 103005 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard 2014/02/10 2016/02/09 Spectrum Analyser FSP3 836722/011 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard 2012/06/13 2015/06/12 Spectrum Analyser FSU26 200418 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2013/07/29 2014/07/28 Vector Signal Generator SMIQ 03B 832492/061 Rohde & Schwarz GmbH & Co.KG Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 24 of 32

Test Equipment Digital Signalling Devices Lab ID: Lab 1, Lab 2, Lab 3 Description: Signalling equipment for various wireless technologies. Single Devices for Digital Signalling Devices Single Device Name Type Serial Number Manufacturer Bluetooth Signalling Unit CBT 100589 Rohde & Schwarz GmbH & Co. CBT KG Calibration Details Last Execution Next Exec. Standard calibration 2011/11/24 2014/11/23 CMW500 CMW500 107500 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/01/27 2016/01/26 Digital Radio CMD 55 831050/020 Rohde & Schwarz GmbH & Co. Communication Tester KG Calibration Details Last Execution Next Exec. Standard calibration 2011/11/28 2014/11/27 Universal Radio CMU 200 102366 Rohde & Schwarz GmbH & Co. Communication Tester KG HW/SW Status Date of Start Date of End Hardware: 2007/07/16 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B56V14, B68 3v04, PCMCIA, U65V04 Software: K21 4v21, K22 4v21, K23 4v21, K24 4v21, K42 4v21, K43 4v21, K53 4v21, K56 4v22, K57 4v22, K58 4v22, K59 4v22, K61 4v22, K62 4v22, K63 4v22, K64 4v22, K65 4v22, K66 4v22, K67 4v22, K68 4v22, K69 4v22 Firmware: µP1 8v50 02.05.06 --- Universal Radio CMU 200 837983/052 Rohde & Schwarz GmbH & Co. Communication Tester KG Calibration Details Last Execution Next Exec. Standard calibration 2011/12/07 2014/12/06 HW/SW Status Date of Start Date of End HW options: 2007/01/02 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B54V14, B56V14, B68 3v04, B95, PCMCIA, U65V02 SW options: K21 4v11, K22 4v11, K23 4v11, K24 4v11, K27 4v10, K28 4v10, K42 4v11, K43 4v11, K53 4v10, K65 4v10, K66 4v10, K68 4v10, Firmware: µP1 8v40 01.12.05 --- SW: 2008/11/03 K62, K69 Vector Signal Generator SMU200A 100912 Rohde & Schwarz GmbH & Co. KG Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 25 of 32

Test Equipment Emission measurement devices Lab ID: Lab 1, Lab 2 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Emission measurement devices Single Device Name Type Serial Number Manufacturer Personal Computer Dell 30304832059 Dell Power Meter NRVD 828110/016 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/05/13 2015/05/12 Sensor Head A NRV-Z1 827753/005 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/05/13 2015/05/12 Signal Generator SMR 20 846834/008 Rohde & Schwarz GmbH & Co. KG Spectrum Analyzer ESIB 26 830482/004 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2014/01/07 2016/01/31 HW/SW Status Date of Start Date of End Firmware-Update 4.34.4 from 3.45 during calibration 2009/12/03 Test Equipment Multimeter 12 Lab ID: Lab 4, Lab 5 Description: Ex-Tech 520 Serial Number: 05157876 Single Devices for Multimeter 12 Single Device Name Type Serial Number Manufacturer Digital Multimeter 12 EX520 05157876 Extech Instruments Corp. (Multimeter) Calibration Details Last Execution Next Exec. Customized calibration 2013/12/04 2015/12/03 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 26 of 32

Test Equipment Radio Lab Test Equipment Lab ID: Lab 3 Description: Radio Lab Test Equipment Single Devices for Radio Lab Test Equipment Single Device Name Type Serial Number Manufacturer Broadband Power Divider WA1515 A856 Weinschel Associates SMA Coax Attenuator 10dB 4T-10 F9401 Weinschel Associates SMA 2W Coax Attenuator 10dB 56-10 W3702 Weinschel Associates SMA 2W Coax Attenuator 10dB 56-10 W3711 Weinschel Associates SMA 2W Coax Cable Sucotest 2,0m Huber&Suhner Huber&Suhner Coax Cable Rosenberger FA210A0010003030 54491-2 Rosenberger Micro-Coax Micro Coax FA210A0010003030 SMA/SMA 1,0m Power Meter NRVD 828110/016 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/05/13 2015/05/12 RF Step Attenuator RSP RSP 833695/001 Rohde & Schwarz GmbH & Co.KG Rubidium Frequency Datum, Model: MFS 5489/001 Datum-Beverly Standard Calibration Details Last Execution Next Exec. Standard calibration 2013/06/24 2014/07/02 Standard calibration 2014/07/03 2015/07/02 Sensor Head A NRV-Z1 827753/005 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2014/05/13 2015/05/12 Signal Generator SME SME03 827460/016 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2011/11/25 2014/11/24 Signal Generator SMP SMP02 836402/008 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2013/05/06 2016/05/05 Spectrum Analyser FSIQ26 840061/005 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2013/02/12 2015/02/11 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 27 of 32

Test Equipment Regulatory Bluetooth RF Test Solution Lab ID: Lab 4 Description: Regulatory Bluetooth RF Tests Type: Bluetooth RF Serial Number: 001 Single Devices for Regulatory Bluetooth RF Test Solution Single Device Name Type Serial Number Manufacturer ADU 200 Relay Box 7 Relay Box A04380 Ontrak Control Systems Inc. Bluetooth Signalling Unit CBT 100302 Rohde & Schwarz GmbH & CBT Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2013/08/28 2014/08/27 Power Meter NRVD NRVD 832025/059 Calibration Details Last Execution Next Exec. Standard calibration 2013/08/26 2014/08/25 Power Sensor NRV Z1 A PROBE 832279/013 Calibration Details Last Execution Next Exec. Standard calibration 2013/08/28 2014/08/27 Power Supply NGSM 32/10 2725 Calibration Details Last Execution Next Exec. Standard calibration 2013/06/20 2015/06/19 Rubidium Frequency Datum MFS 002 Datum GmbH Normal MFS Calibration Details Last Execution Next Exec. Standard calibration 2013/08/27 2014/08/26 Signal Analyser FSIQ26 1119.6001.26 832695/007 Rohde & Schwarz GmbH & Co.KG Vector Signal Generator SMIQ03B 832870/017 SMIQ03B Calibration Details Last Execution Next Exec. Standard calibration 2013/06/21 2016/06/20 Test Equipment Shielded Room 02 Lab ID: Lab 1 Manufacturer: Frankonia Description: Shielded Room for conducted testing Type: 12 qm Serial Number: none Test Equipment Shielded Room 07 Lab ID: Lab 4, Lab 5 Description: Shielded Room 4m x 6m Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 28 of 32

Test Equipment T/A Logger 13 Lab ID: Lab 1, Lab 2, Lab 3 Description: Lufft Opus10 TPR Type: Opus10 TPR Serial Number: 13936 Single Devices for T/A Logger 13 Single Device Name Type Serial Number Manufacturer ThermoAirpressure Opus10 TPR (8253.00) 13936 Lufft Mess- und Regeltechnik Datalogger 13 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/02/07 2015/02/06 Test Equipment T/H Logger 02 Lab ID: Lab 1 Description: Lufft Opus10 Serial Number: 7489 Single Devices for T/H Logger 02 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 7489 Lufft Mess- und Regeltechnik 02 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/02/07 2015/02/06 Test Equipment T/H Logger 03 Lab ID: Lab 3 Description: Lufft Opus10 Serial Number: 7482 Single Devices for T/H Logger 03 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 7482 Lufft Mess- und Regeltechnik 03 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/02/07 2015/02/06 Test Equipment T/H Logger 12 Lab ID: Lab 2 Description: Lufft Opus10 Serial Number: 12482 Single Devices for T/H Logger 12 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 12482 Lufft Mess- und Regeltechnik 12 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/01/07 2015/01/06 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 29 of 32

Test Equipment T/H Logger 15 Lab ID: Lab 4, Lab 5 Description: Lufft Opus10 Serial Number: 13985 Single Devices for T/H Logger 15 Single Device Name Type Serial Number Manufacturer ThermoHygro Datalogger Opus10 THI (8152.00) 13985 Lufft Mess- und Regeltechnik 15 (Environ) GmbH Calibration Details Last Execution Next Exec. Customized calibration 2013/01/07 2015/01/06 Test Equipment Temperature Chamber 01 Lab ID: Lab 4, Lab 5 Manufacturer: see single devices Description: Temperature Chamber KWP 120/70 Type: Weiss Serial Number: see single devices Single Devices for Temperature Chamber 01 Single Device Name Type Serial Number Manufacturer Temperature Chamber KWP 120/70 59226012190010 Weiss Umwelttechnik GmbH Weiss 01 Calibration Details Last Execution Next Exec. Customized calibration 2014/03/12 2016/03/11 Test Equipment Temperature Chamber 05 Lab ID: Lab 3 Manufacturer: see single devices Description: Temperature Chamber VT4002 Type: Vötsch Serial Number: see single devices Single Devices for Temperature Chamber 05 Single Device Name Type Serial Number Manufacturer Temperature Chamber VT 4002 58566080550010 Vötsch Vötsch 05 Calibration Details Last Execution Next Exec. Customized calibration 2014/03/11 2016/03/10 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 30 of 32

Test Equipment WLAN RF Test Solution Lab ID: Lab 5 Manufacturer: 7 layers AG Description: Regulatory WLAN RF Tests Type: WLAN RF Serial Number: 001 Single Devices for WLAN RF Test Solution Single Device Name Type Serial Number Manufacturer Arbitrary Waveform TGA12101 284482 Generator Power Meter NRVD NRVD 832025/059 Calibration Details Last Execution Next Exec. Standard calibration 2013/08/26 2014/08/25 Power Sensor NRV Z1 A PROBE 832279/013 Calibration Details Last Execution Next Exec. Standard calibration 2013/08/28 2014/08/27 Power Supply NGSM 32/10 2725 Calibration Details Last Execution Next Exec. Standard calibration 2013/06/20 2015/06/19 Rubidium Frequency Datum MFS 002 Datum GmbH Normal MFS Calibration Details Last Execution Next Exec. Standard calibration 2013/08/27 2014/08/26 Signal Analyser FSIQ26 1119.6001.26 832695/007 Rohde & Schwarz GmbH & Co.KG Spectrum Analyser FSU26 100136 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard Calibration 2014/01/06 2015/01/05 HW/SW Status Date of Start Date of End FSU FW Update to v4.61 SP3, K5 v4.60 and K73 v4.61 2011/12/05 Spectrum Analyser FSU3 200046 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2013/06/20 2014/06/19 HW/SW Status Date of Start Date of End Firmware Version 4.51 SP1 2011/12/07 Option FS-K72 4.50 SP1 Option FS-K73 4.50 SP1 TOCT Switching Unit Switching Unit 040107 7 layers, Inc. Vector Signal Generator SMIQ03B 832870/017 SMIQ03B Calibration Details Last Execution Next Exec. Standard calibration 2013/06/21 2016/06/20 Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 31 of 32

5 Photo Report Please refer to external report. 6 Setup Drawings Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting groundplane. Test report Reference: MDE_DATA_1405_FCCi_Rev1 Page 32 of 32


Document Created: 2014-08-26 11:29:07
Document Modified: 2014-08-26 11:29:07
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC