Test report RFID

FCC ID: U4GJNG3SD

Test Report

Download: PDF
FCCID_3230204

TEST REPORT No.: 2-20842790-15-11a According to: FCC Regulations Part 15.225 Part 15.207 Part 15.209 IC Regulations RSS-210, Issue 9 RSS-Gen Issue 4 for Datalogic ADC S.r.l. JOYA TOUCH 3-SLOT CRADLE FCC-ID: U4GJNG3SD IC: 3862E-JNG3SD PMN: JOYA TOUCH 3-SLOT CRADLE HVIN: 3SD WPT Laboratory Accreditation and Listings Voluntary Controls for Industry Canada Electromagnetic Emissions Reg. No.: 3462D-2 Reg. No.: MRA US-EU 0003 R-2666 C-2914, Reg. No.: 3462D-3 T-1967, G-301 accredited according to DIN EN ISO/IEC 17025 CETECOM GmbH Laboratory Radio Communications & Electromagnetic Compatibility Im Teelbruch 116 • 45219 Essen • Germany Registered in Essen, Germany, Reg. No.: HRB Essen 8984 Tel.: + 49 (0) 20 54 / 95 19-954 • Fax: + 49 (0) 20 54 / 95 19-964 E-mail: info@cetecom.com • Internet: www.cetecom.com Page 1 of 25 The test results relate only to the individual items which have been tested. This report shall not be reproduced in parts without the written approval of the testing laboratory © Copyright: All rights reserved by CETECOM

Test Report 2-20842790-15-11a, Page 2 of 25 TABLE OF CONTENTS 1. SUMMARY OF TEST RESULTS ..................................................................................................................... 3 1.1. Tests overview according CFR47, Part 15, Subpart C .................................................................................... 3 2. ADMINISTRATIVE DATA .............................................................................................................................. 4 2.1. Identification of the testing laboratory ............................................................................................................ 4 2.2. Test location ................................................................................................................................................... 4 2.3. Organizational items ....................................................................................................................................... 4 2.4. Applicant’s details .......................................................................................................................................... 4 2.5. Manufacturer’s details .................................................................................................................................... 4 3. EQUIPMENT UNDER TEST (EUT) ................................................................................................................ 5 3.1. Technical data of main EUT declared by applicant ........................................................................................ 5 3.2. EUT: Type, S/N etc. and short descriptions used in this test report ............................................................... 5 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions ................................................................. 6 3.4. EUT set-ups .................................................................................................................................................... 6 3.5. EUT operating modes ..................................................................................................................................... 6 4. DESCRIPTION OF TEST SYSTEM SET-UP’S ............................................................................................. 7 4.1. Test system set-up for AC power-line conducted emission measurements .................................................... 7 4.2. Test system set-up for conducted measurements on antenna port ................................................................... 8 4.3. Test system set-up for radiated magnetic field measurements below 30 MHz ................................................ 9 4.4. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz .............................................. 10 5. MEASUREMENTS ............................................................................................................................................ 11 5.1. General Limit - Conducted emissions on AC-Power lines ............................................................................. 11 5.2. Radiated field strength emission mask at 13.110-14.010MHz ....................................................................... 12 5.3. General Limit - Radiated field strength emissions below 30 MHz ................................................................. 13 5.4. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz ............................................................. 15 5.5. Frequency error (tolerance) ............................................................................................................................ 17 5.6. Measurement uncertainties ............................................................................................................................. 20 6. ACCREDITATION DETAILS OF CETECOM’S LABORATORIES AND TEST SITES ........................ 21 7. INSTRUMENTS AND ANCILLARY ............................................................................................................... 22 7.1. Used equipment “CTC” .................................................................................................................................. 22 8. VERSIONS OF TEST REPORTS (CHANGE HISTORY) ............................................................................ 25 Table of annex The listed attachments are an integral part of this report Total pages Annex 1: Test result diagrams (separate document) TR2-20842790-15-11a-A1 32 Annex 2: External photographs of EUT (separate document) TR2-20842790-15-11a-A2 5 Annex 3: Internal photographs of EUT (separate document) TR2-20842790-15-11a-A3 12 Annex 4: Test set-up photographs (separate document) TR2-20842790-15-11a-A4 9 Operational Description_JOYA TOUCH 3-SLOT CRADLE_20160530_rev03 (supplied by applicant) 7 JOYANG_TEST-TOOLS_QUICK_START_INSTRUCTIONS_REV20160530 (supplied by applicant) 41 Operational Description_JOYA TOUCH_20160530_rev05 (supplied by applicant) 10 TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 3 of 25 1. Summary of test results The test results apply exclusively to the test samples as presented in this Report. The CETECOM GmbH does not assume responsibility for any conclusions and generalizations taken in conjunction with other specimens or samples of the type of the item presented to tests. The Equipment Under Test (in this report, hereinafter referred as EUT) is a radio transmitting device with a integrated RFID Transmitter at nominal 13.56MHz. 1.1. Tests overview according CFR47, Part 15, Subpart C REFERENCES & LIMITS EUT EUT opera- TEST CASES PORT FCC Standard Result TEST LIMIT set-up ting RSS Standard mode FIELD §2.1046 FCC Part 15.225 limits STRENGTH §15.225 (radiated in 30m (a)(b) Cabinet 1 1 Pass measurement (c)(d) distance) & EMISSION MASK RSS-210 , Issue9 IC: Annex B.6 §2.202 99% Power Antenna For 99% OCCUPIED §2.1049 coupling 2 1 information BANDWIDTH (radiated) only RSS-Gen Issue 4 IC: Chapter 6.6 Cabinet §15.209(a) FCC:2400/F(kHz) µV/m SPURIOUS + 24000/F(kHz) µV/m EMISSIONS Intercon 30 µV/m 1 1 Pass (radiated) necting cables RSS-Gen Issue 4 IC: Chapter 8.9 (radiated) §2.1055 FCC: ±100ppm FREQUENCY Antenna §15.225(e) coupling 2 2 Pass STABILITY (radiated) RSS-210 , Issue 9 IC: ±0.01% (±100 ppm). AC-Power Lines AC- §15.207 FCC §15.207 limits Power 3 1 Pass Conducted lines RSS-Gen Issue 4 IC: Table 4, Chapter 7.2.4 Emissions Digitally signed by christian. Digital unterschrieben von lorenz@cetecom.com Ajit Phadtare DN: cn=Ajit Phadtare, DN: cn=christian. o=CETECOM GmbH, ou=RC- lorenz@cetecom.com EMC, email=ajit.phadtare@ceteco Date: 2016.12.05 10:33:13 m.com, c=DE Datum: 2016.12.05 10:27:35 +01'00' +01'00' ...................................................... .................................................... Dipl.-Ing. Ch. Lorenz MSc. Ajit Phadtare Responsible for test section Responsible for test report TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 4 of 25 2. Administrative Data 2.1. Identification of the testing laboratory Company name: CETECOM GmbH Address: Im Teelbruch 116 45219 Essen - Kettwig Germany Responsible for testing laboratory: Dipl.-Ing. Rachid Acharkaoui Deputy: Dipl.-Ing. Niels Jeß 2.2. Test location 2.2.1. Test laboratory “CTC” Company name: see chapter 2.1. Identification of the testing laboratory 2.3. Organizational items Responsible for test report : MSc. Ajit Phadtare Project leader: Dipl.-Ing. V. Krueger Receipt of EUT: 2016-02-29 Date(s) of test: 2016-04-21 to 2016-06-28 Date of report: 2016-12-05 ----------------------------------------------------------------------------------------------------------------------------------------------------- Version of template: 13.02 2.4. Applicant’s details Applicant’s name: Datalogic ADC S.r.l. Address: Via S. Vitalino, 13 40012, Lippo di Calderara di Reno (BO) ITALY Contact person: Mr.Eucarpio Guarisco 2.5. Manufacturer’s details Manufacturer’s name: please see Applicant's details Address: please see Applicant's details TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 5 of 25 3. Equipment under test (EUT) 3.1. Technical data of main EUT declared by applicant Main function Wireless charger for JOYA TOCUH Terminals Type JOYA TOUCH 3-SLOT CRADLE Frequency range and channels 13.553 -13.567 MHz (US/Canada -bands) Type of modulation (packet types) ASK (Amplitude Shift Keying) Occupied bandwidth 38.94 kHz Number of channels 1 nominal channel at 13.56MHz (USA/Canada -bands)  Integrated Antenna Type  External, no RF- connector  External, separate RF-connector Antenna Gain No information from applicant MAX Field strength (radiated): 26.73 dBμV/m Peak@30m distance Installed options  battery charging option (WPC) (not tested within this test report) Power supply  12 V DC using AC/DC adapter: 120V/60 Hz Special EMI components -- EUT sample type  Production  Pre-Production  Engineering Firmware  for normal use  Special version for test execution FCC label attached  yes  no 3.2. EUT: Type, S/N etc. and short descriptions used in this test report Short S/N HW SW descrip- EUT Type serial hardware status software status tion*) number Beta 2 HW Firmware JOYA TOUCH Version EUT A N/A Z15P00993 Version: 3- SLOT CRADLE P/N:91ACC0043 99.99.99 *) EUT short description is used to simplify the identification of the EUT in this test report. TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 6 of 25 3.3. Auxiliary Equipment (AE): Type, S/N etc. and short descriptions AE S/N HW SW short Auxiliary Equipment Type serial number hardware status software status descrip- tion *) SW Beta HW P00AN04HL0H Version:WEC7 AE 1 JOYA TOUCH Z16P00044 Version T0W7-GR0 Firmware P/N:911350015 Version: 2.16 SW Beta HW P00AN04HL0G Version:WEC7 AE 2 JOYA TOUCH Z16P00014 Version T0W7-GRR Firmware P/N:9113500013 Version: 2.16 AC/DC Adapter 120 V AC 60 Hz AE 3 EDACPOWER EA10681U-120 331210680014C3 -- to 12VDC 6 A ELEC *) AE short description is used to simplify the identification of the auxiliary equipment in this test report. 3.4. EUT set-ups EUT set-up Combination of EUT and AE Remarks no.*) set. 1 EUT A + AE 1+AE 3 Radiated Measurements table top set up set. 2 EUT A + AE 2+AE 3 Conducted Measurements Antenna coupling set up set. 3 EUT A + AE 1+AE 3 AC-Power Lines Conducted Emissions set up *) EUT set-up no. is used to simplify the identification of the EUT set-up in this test report. 3.5. EUT operating modes EUT Description of operating Additional information operating modes mode no.*) Continuous NFC (13.56 MHz) Tx mode activated between EUT A & AE 1 using Cradle Test application. TX-Mode op. 1 - modulated signal with maximum output power Modulated - Duty-Cycle greater than 98%. - AE1 used for exchanging the RF information. Continuous NFC (13.56 MHz) Tx mode activated in only EUT A TX-Mode - unmodulated signal with maximum output power op. 2 Unmodulated - Duty-Cycle greater than 98%. - AE1 used only to maintain unmodulated NFC signal *) EUT operating mode no. is used to simplify the test report. TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 7 of 25 4. Description of test system set-up’s 4.1. Test system set-up for AC power-line conducted emission measurements Specification: ANSI C63.4-2009 chapter 7, ANSI C63.10-2013 chapter 6.2 General Description: The radio frequency voltage conducted back into the AC power line in the frequency range 150 kHz to 30 MHz has to be investigated. Compliance should be tested by measuring the radio frequency voltage between each power line and ground at the power terminals in the stated frequency range. A 50 Ohm / 50 µH line impedance stabilization network (LISN) is used coupling the interface to the measurement equipment. The EUT power input leads are connected through the LISN to the AC-power source. The LISN enclosure is electrically connected to the ground plane. The measuring instrument is connected to the coaxial output of the LISN. Tabletop devices were set-up on a 80 cm height above reference ground plane, floor standing equipment 10 cm raised above ground plane. Measurements have been performed on each phase line and neutral line of the devices AC-power lines. The EUT was power supplied with 110 V/60 Hz. The EUT was tested in the defined operating mode and installed (connected) to accessory equipment according the general description of use given by the applicant. Schematic: Only schematic view, we refer to figure 6, 7 and 8 of ANSI C63.4-2009 for more details. Testing method: Exploratory, preliminary measure- Final testing for power phases and ments as a first step, determines the critical frequencies (Margin to AV- or worst-case phase line (neutral or phase) QP limit lower than 3 dB) as a second as well as the most critical operating step includes measurements with mode of the equipment. A complete receivers detector set to Quasi-Peak and frequency-sweep with PK-Detector is Average. performed on each current-carrying conductor. Formula: VC= VR + CL (1) VC = measured Voltage –corrected value M= LT-VC (2) VR = Receiver reading CL = Cable loss M = Margin LT = Limit Values are in dB, positive margin means value is below limit. TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 8 of 25 4.2. Test system set-up for conducted measurements on antenna port Specification: ANSI 63.10:2013 Schematic: In case an external connector is not available, the coupling unit consists of a near-field antenna which is directly connected to the spectrum analyzer. Testing method: ANSI 63.10:2013, Chapter 6.7 TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 9 of 25 4.3. Test system set-up for radiated magnetic field measurements below 30 MHz Specification: ANSI C63.4-2009 chapter 8.2.1, ANSI C63.10-2013 chapter 6.4 General Description: Evaluating the radiated field emissions are done first by an exploratory emission measurement and a final measurement for most critical frequencies determined. The loop antenna was placed at 1 m height above ground plane and 3 m measurement distance from set-up for investigations. Because of reduced measurement distance, correction data were applied, as stated in chapter “General Limit - Radiated field strength emissions below 30 MHz“. The tests are performed in the semi anechoic room recognized by the regulatory commission. Schematic: Testing method: Exploratory, preliminary measurement Final measurement on critical frequencies The EUT and it’s associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 0.8 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (step cable position, etc. 90°, range 0°to 360°) and the EUT itself either on 3-orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT), the emission spectrum was recorded. The precisely. After this step, for all identified critical loop antenna was moved at least to frequencies, the maximum peak was determined. 2-perpendicular axes (antenna vector in direction of EUT and parallel to EUT) in order to Following parameters were varied: the turntable maximize the emissions. The results are angle continuously in the range 0 to 360 degree, documented in a diagram. Critical frequencies the EUT itself either over 3-orthogonal axis (not (low margin to limit) are saved within a data defined usage position) or 2-orthogonal axis reduction table for further investigations. If (defined usage position). various operating modes are supported, further investigations are made to find the worst-case. On the determined worst-case position, a final Also the interconnection cables and equipment measurement with necessary bandwidth and position were varied in order to maximize the detector according standard has been carried out. emissions. Formula: EC = ER + AF + CL + DF - GA AF =Antenna factor CL = Cable loss M = LT-EC DF= Distance correction factor EC = Electrical field – corrected value ER = Receiver reading GA= Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. Distance correction: Reference for applied correction (extrapolating) factors: IEEC Transaction EMC, Vol. 47, No. 3 , Aug. 2005, Journal Paper “Extrapolating Near-field emissions of low frequency loop transmitters”. TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 10 of 25 4.4. Test system set-up for radiated electric field measurement 30 MHz to 1 GHz Specification: ANSI C63.4-2009 chapter 8, ANSI C63.10-2013 chapter 6.5 General Description: Evaluating the field emissions have to be done first by an exploratory emissions measurement and a final measurement for most critical frequencies. The tests are performed in a NSA-compliant semi anechoic room (SAR) recognized by the regulatory commissions. Schematic: Testing method: Exploratory, preliminary measurements Final measurement on critical frequencies The EUT and its associated accessories are Based on the exploratory measurements, the most placed on a non-conductive position manipulator critical frequencies are re-measured by main- (tipping device) of 0.8 m height which is placed taining the EUT’s worst-case operation mode, on the turntable. By rotating the turntable (range cable position, etc. 0° to 360°, step 90°) and the EUT itself either on 3-orthogonal axis (portable equipment) or 2- First a frequency zoom around the critical orthogonal axis (defined operational position of frequency is done to locate the frequency more EUT) the emission spectrum and it’s precisely. After this step, for all identified critical characteristics was recorded with an EMI- frequencies, the maximum peak was determined. receiver, broadband antenna and software. Following parameters were varied: the turntable Measurement antenna: horizontal and vertical, angle continuously in the range 0 to 360 degree, heights: 1,0 m and 1,82 m as worst-case the EUT itself either over 3-orthogonal axis (not determined by an exploratory emission defined usage position) or 2-orthogonal axis measurements. The results are documented in a (defined usage position). The measurement diagram. Critical frequencies (low margin to antenna height between 1 m and 4 m. limit) are saved within a table for further investigations. If various operating modes are On the determined worst-case position, a final supported, further investigations are made to find measurement with necessary bandwidth and the worst-case of them. Also the interconnection detector according standard has been carried out. cables and equipment position were varied in order to maximize the emissions. Formula: EC = ER + AF + CL + DF - GA (1) AF = Antenna factor CL = Cable loss M = LT - EC (2) DF = Distance correction factor (if used) EC = Electrical field – corrected value ER = Receiver reading GA = Gain of pre-amplifier (if used) LT = Limit M = Margin All units are dB-units, positive margin means value is below limit. TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 11 of 25 5. Measurements 5.1. General Limit - Conducted emissions on AC-Power lines 5.1.1. Test location and equipment test location  CETECOM Essen (Chapter 2.2.1) Please see Chapter 2.2.2  Please see Chapter 2.2.3 test site  333 EMI field  348 EMI cond. receiver  001 ESS  377 ESCS 30 489 ESU 40  620 ESU 26 LISN  005 ESH2-Z5  007 ESH3-Z6 300 ESH3-Z5 & 50 used for AE  no LISN for AE signaling  392 MT8820A  436 CMU 547 CMU  594 CMW line voltage  12 VDC (for EUT A supplied from AE3)  060 120 V 60 Hz via PAS 5000 (for AE3) 5.1.2. Requirements FCC Part 15, Subpart B, §15.207 IC RSS-Gen Issue 4, Chapter 8.8, Table 3 ANSI C63.10-2013 Frequency Limit [MHz] QUASI-Peak [dBµV] AVERAGE [dBµV] 0.15 – 0.5 66 to 56* 56 to 46* Class B 0.5 – 5 56 46 5 – 30 60 50 Remark: * decreases with the logarithm of the frequency 5.1.3. Test condition and test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing (40 cm distance to reference EUT stands isolated on reference ground plane (floor) ground plane (wall) Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)%  9 – 150 kHz, RBW = 200 Hz, Step = 61 Hz Scan data  150 kHz – 30 MHz RBW = 9 kHz, Step = 4 kHz EMI-Receiver or  other: Analyzer settings Scan-Mode 6 dB EMI-Receiver Mode Pre-measurement Peak detector, Repetitive-Scan, max-hold, sweep-time 50 µs per frequency point Final measurement Average & Quasi-peak detector at critical frequencies General measurement procedures Please see chapter “Test system set-up for AC power line conducted emissions measurements” 5.1.4. Measurement results The results are presented below in summary form only. For more information please see the diagrams Set-up no.:3 EUT OP-mode no.: 1 Diagram- Power Result Used Detector Additional (scan-) information Remarks No. line Measurement performed with NFC  Peak (pre-scan) antenna in normal operating mode. For Remark 1) 1.01  CAV (final) L1/ N Inconclusive compliance further investigations are Remark 2)  QP (final) necessary.  Peak (pre-scan) Measurement performed without NFC 1.01b  CAV (final) L1/ N antenna & NFC output port Remark 1) Pass  QP (final) terminated with 50 Ohm impedance. Remark: 1.) For further details please refer diagrams in separate annex A1 2.) Reference Measurement diagram No .1.01 is valid only in combination with Measurement diagram No .1.01b TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 12 of 25 5.2. Radiated field strength emission mask at 13.110-14.010MHz 5.2.1.TEST LOCATION AND EQUIPMENT (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS     spectr. analys.  120 FSEM  264 FSEK     antenna  048 EMCO3143  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  power supply  087 EA 3013 S  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix  477 GPS  line voltage  12 VDC (for EUT A supplied from AE3)  060 120 V 60 Hz via PAS 5000 (for AE3) 5.2.2. STANDARDS AND LIMITS: CFR 47, §15.225(a)(b)(c)(d) & RSS-210, Issue 9 Annex B.6 Field strength Measurement Frequency distance Remarks [MHz] [μV/m] [dBuV/m] [meters] 13.553 -13.567 15.848 84.00 30 (allocated band) 13.410-13.710 334 50.47 30 Correction factor used due to measurement 13.110-14.010 106 40.50 30 distance of 3m Outside band 30 29.5 30 13.110-14.010 5.2.3. TEST CONDITION AND MEASUREMENT TEST SET-UP link to test system (if used):  air link  cable connection  EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver (Analyzer) Settings Span/Range: 9kHz to 150kHz; 150 kHz to 30 MHz RBW/VBW: 200Hz/auto; 10 kHz/ auto (ANSI63.10/CISPR#16) Detector/ Mode: PEAK, TRACE max-hold mode, repetitive scan for exploratory measurements Quasi-Peak, for final measurement on critical frequencies (f<1GHz) 5.2.4. GENERAL MEASUREMENT PROCEDURES: The measurement test set-up and test procedure are in accordance with the provisions described in ANSI 63.10: 2013 The Equipment under Test (EUT) was set-up to defined operating mode and installed (connected) to accessory equipment according the general description of use given by the applicant. The measurement loop antenna was situated in 3m distance to the EUT. Between EUT and measurement antenna absorbers are covering the GND-Plane. Radiated magnetic emission measurements were made with the antenna situated in 1 meter height. The loop antenna was moved at least to 2-perpendicular axes (antenna vector in direction of EUT and parallel to EUT) in order to maximize the emissions, the EUT itself either over 3- orthogonal axes (no defined usage position) or 2-orthogonal axis (defined usage position). According the standard the compliance should be checked in 30m measurement distance. Therefore an additional extrapolation factor was used in order to normalize the measurement data. The frequency dependent extrapolation factor used for this reduced measurement distance, can be found in the chapter 5.3.4.1 5.2.5. MEASUREMENT RESULTS: CARRIER FIELD STRENGTH (EMISSION MASK) Carrier Set- OP- Diagram Frequency Used detector Channel up mode Remark Result No. range no. no. Range No. PK AV QP 2.05 nominal 1 12 - 15 MHz 1 1 Carrier field strength:26.73 dBuV/m    Pass Remark: 1.) For further details please refer diagrams in separate annex A1 5.2.6. VERDICT: Pass TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 13 of 25 5.3. General Limit - Radiated field strength emissions below 30 MHz 5.3.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  347 Radio.lab.   receiver  377 ESCS30  001 ESS     spectr. analys.  584 FSU  120 FSEM  264 FSEK    antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix  378 RadiSense DC power  087 EA 3013S  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 line voltage  12 VDC (for EUT A supplied from AE3)  060 120 V 60 Hz via PAS 5000 (for AE3) 5.3.2. Requirements FCC Part 15, Subpart C, §15.205 & §15.209 IC RSS-Gen., Issue 4: Chapter 8.9, Table 5 ANSI C63.10-2013 Frequency Field strength limit Distance Remarks [MHz] [μV/m] [dBμV/m] [m] 0.009 – 0.490 2400/f (kHz) 67.6 – 20Log(f) (kHz) 300 Correction factor used due to measurement distance of 3 m 0.490 – 1.705 24000/f (kHz) 87.6 – 20Log(f) (kHz) 30 Correction factor used due to measurement distance of 3 m 1.705 – 30 30 29.5 30 Correction factor used due to measurement distance of 3 m 5.3.3. Test condition and test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)%  9 – 150 kHz RBW/VBW = 200 Hz Scan step = 80 Hz Scan data  150 kHz – 30 MHz RBW/VBW = 9 kHz Scan step = 4 kHz  other: EMI-Receiver or Scan-Mode  6 dB EMI-Receiver Mode  3dB Spectrum analyser Mode Analyzer Settings Detector Peak (pre-measurement) and Quasi-PK/Average (final if applicable) Mode: Repetitive-Scan, max-hold Sweep-Time Coupled – calibrated display if continuous signal otherwise adapted to EUT’s individual transmission duty-cycle General measurement procedures Please see chapter “Test system set-up radiated magnetic field measurements below 30 MHz” 5.3.4. Measurement Results The results are presented below in summary form only. The EUT is put on operation on nominal channel. Table of measurement results: Carrier Set- OP- Diagram Used detector Channel Frequency range up mode Remark Result No. no. no. Range PK AV QP 13.56 MHz NFC Carrier on 2.06 Nominal 9 kHz-30 MHz 1 1    Pass diagram: Not relevant for verdict Remark: 1.) For further details please refer diagrams in separate annex A1 TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 14 of 25 5.3.4.1. Correction factors due to reduced meas. distance (f< 30 MHz) The used correction factors when the measurement distance is reduced compared to regulatory measurement distance, are calculated according Extrapolation formulas valid for EUT’s with maximum dimension of 0.625xLambda. Formula 2+3+4 as presented in ANSI C63.10, Chapter 6.4.4 are used for the calculations of proper extrapolation factors. TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 15 of 25 5.4. General Limit - Radiated field strength emissions, 30 MHz - 1 GHz 5.4.1. Test location and equipment test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA receiver  377 ESCS30  001 ESS  489 ESU 40  620 ESU 26 spectr. analys.  584 FSU  120 FSEM  264 FSEK antenna  574 BTA-L  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  477 GPS signaling  392 MT8820A  371 CBT32  547 CMU  594 CMW otherwise  400 FTC40x15E  401 FTC40x15E  110 USB LWL  482 Filter Matrix DC power  087 EA 3013S  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE line voltage  12 VDC (for EUT A supplied from AE3)  060 120 V 60 Hz via PAS 5000 (for AE3) 5.4.2. Requirements/Limits  Part 15 Subpart B, §15.109, class B FCC  Part 15 Subpart C, §15.209 @ frequencies defined in §15.205  RSS-Gen., Issue 4, Chapter 8.9, Table 4 IC  C63.4-2009 ANSI  C63.10-2013 Radiated emissions limits, 3 meters Frequency [MHz] QUASI Peak [µV/m] QUASI-Peak [dBµV/m] 30 - 88 100 40.0 Limit 88 - 216 150 43.5 216 - 960 200 46.0 above 960 500 49.0 5.4.3. Restricted bands of operation, §15.205 MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 0.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.20725-4.20775 37.5-38.25 1645.5-1646.5 9.3-9.5 6.215-6.218 73-74.6 1660-1710 10.6-12.7 6.26775-6.26825 74.8-75.2 1718.8-1722.2 13.25-13.4 6.31175-6.31225 108-121.94 2200-2300 14.47-14.5 8.291-8.294 123-138 2310-2390 15.35-16.2 8.362-8.366 149.9-150.05 2483.5-2500 17.7-21.4 8.37625-8.38675 156.52475-156.52525 2690-2900 22.01-23.12 8.41425-8.41475 156.7-156.9 3260-3267 23.6-24.0 12.29-12.293 162.0125-167.17 3332-3339 31.2-31.8 12.51975-12.52025 167.72-173.2 3345.8-3358 36.43-36.5 12.57675-12.57725 240-285 3600-4400 -- 13.36-13.41 322-335.4 -- -- Remark: only spurious emissions are allowed within these frequency bands not exceeding the limits per §15.209 TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 16 of 25 5.4.4. Test condition and measurement test set-up Signal link to test system (if used):  air link  cable connection  none EUT-grounding  none  with power supply  additional connection Equipment set up  table top 0.8m height  floor standing Climatic conditions Temperature: (22±3°C) Rel. humidity: (40±20)% EMI-Receiver Scan frequency range:  30 – 1000 MHz  other: (Analyzer) Settings Scan-Mode  6 dB EMI-Receiver Mode  3 dB spectrum analyser mode Detector Peak / Quasi-peak RBW/VBW 100 kHz/300 kHz Mode: Repetitive-Scan, max-hold Scan step 80 kHz Sweep-Time Coupled – calibrated display if continuous tx-signal otherwise adapted to EUT’s individual duty-cycle General measurement procedures Please see chapter “Test system set-up for electric field measurement in the range 30 MHz to 1 GHz” 5.4.5. MEASUREMENT RESULTS The results are presented below in summary form only. For more information please see diagrams. Table of measurement results: Dia- Carrier Channel Set- OP- Used detector Result gram Frequency range up mode Remark no. no. no. Range PK AV QP 3.06 Nominal 30 MHz – 1 GHz 1 1 --    Pass Remark: 1.) For further details please refer diagrams in separate annex A1 TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 17 of 25 5.5. Frequency error (tolerance) 5.5.1. Test location and equipment (for reference numbers please see chapter 'List of test equipment') test location  CETECOM Essen (Chapter. 2.2.1)  Please see Chapter. 2.2.2  Please see Chapter. 2.2.3 test site  441 EMI SAR  487 SAR NSA  337 OATS  347 Radio.lab.   receiver  377 ESCS30  001 ESS     spectr. analys.  489 ESU40  584 FSU8     antenna  048 EMCO3143  133 EMCO3115  302 BBHA9170  289 CBL 6141  030 HFH-Z2  431 Model 7405 signaling  298 CMU  460 CMU  295 RACAL  392 MT8820A   power supply  456 EA 3013A  457 EA 3013A  459 EA 2032-50  268 EA- 3050  494 AG6632A  498 NGPE 40 otherwise  331 HC4055  401 FTC40x15E  627 OPUS1  477 GPS  line voltage  230 V 50 Hz via public mains  060 120 V 60 Hz via PAS 5000 5.5.2. Standards and Limits: CFR 47, §15.225, ANSI 63.10: 2009 & RSS-210, Issue 9 Annex B.6 Frequency Frequency tolerance Remarks [MHz] [%] [ppm] [Hz] 13.553 -13.567 ±0.01 ±100 ±1356.7 -- 5.5.3. TEST SET-UP A sniffer antenna acts like a coupling antenna for measuring the fundamental frequency. This is placed closed the equipment which is situated inside an climatic chamber. Also connecting cables at the equipment are avoided on the extent possible in order not to degrade the resonance frequency of the equipment and integral antenna. 5.5.4. EQUIPMENT SETTINGS The measurements is made on nominal carrier frequency within operational band. Further settings on the Spectrum-analyser can be checked on the screenshots attached. 5.5.5. TEST METHOD A trace with low RBW function was recorded. The maximum peak within the span was found, then the frequency deviation was recorded with the build-in frequency counter within the spectrum-analyser ESU40 to minimize the measurement uncertainty. The frequency deviation was recorded at switching on point of the equipment and on 2 minutes, 5 minutes and 10 minutes after at in accordance with ANSI 63.10: 2013, Chapter 6.8 All measurements data in graphical format are enclosed in annex 1. TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 18 of 25 5.5.5.1. Frequency shift of carrier against temperature at constant power supply voltage 1.) Use a full loaded battery for tests according this chapter 2.) determine the carrier frequency at room temperature and nominal voltage [20°C] after a long run of the device equipment (EUT). This frequency is taken as reference for all other measured frequencies. 3.) Perform the carrier frequencies measurements in 10°C increments from 50°C down to -20°C as required by the standards. The stabilization period was about 1 hour after thermal reach of the required temperature. 5.5.5.1.1. Results Temperature Variation at Nominal Primary Supply Voltage Frequency error (tolerance) §15.225 & RSS 210 Set- up no.2 EUT OP-mode no. 2 Nominal Conditions Vnom = 12.V DC Reference Limit-> (from AE3 120 V AC / 60 Hz) 13.5599346 MHz 1355.99346 Hz Tnom = 21°C frequency 100ppm: Extreme Temperature Conditions Measurement period Frequency Temperature Frequency Error after power- measured up the EUT [MHz] [Hz] [%] [ppm] on StartUp 13.5599127 21.9000000 0.000162 1.62 2 Minutes 13.5599041 30.5000000 0.000225 2.25 Tmax=50°C 5 Minutes 13.5599016 33.0000000 0.000243 2.43 10 Minutes 13.5598999 34.7000000 0.000256 2.56 on StartUp 13.5599277 6.9000000 0.000051 0.51 2 Minutes 13.5599160 18.6000000 0.000137 1.37 T=40°C 5 Minutes 13.5599129 21.7000000 0.000160 1.60 10 Minutes 13.5599117 22.9000000 0.000169 1.69 on StartUp 13.5599256 9.0000000 0.000066 0.66 2 Minutes 13.5599252 9.4000000 0.000134 0.69 T=30°C 5 Minutes 13.5599249 9.7000000 0.000072 0.72 10 Minutes 13.5599249 9.7000000 0.000072 0.72 on StartUp 13.5599159 18.7000000 0.000138 1.38 2 Minutes 13.5599742 -39.6000000 -0.000292 -2.92 T=10°C 5 Minutes 13.5599780 -43.4000000 -0.000320 -3.20 10 Minutes 13.5599716 -37.0000000 -0.000273 -2.73 StartUp 13.5599663 -31.7000000 -0.000234 -2.34 2 Minutes 13.5600051 -70.5000000 -0.000520 -5.20 T=0°C 5 Minutes 13.5600036 -69.0000000 -0.000509 -5.09 10 Minutes 13.5600029 -68.3000000 -0.000504 -5.04 StartUp 13.5600037 -69.1000000 -0.000510 -5.10 2 Minutes 13.5600114 -76.8000000 -0.000566 -5.66 T=-10°C 5 Minutes 13.5600120 -77.4000000 -0.000571 -5.71 10 Minutes 13.5600122 -77.6000000 -0.000572 -5.72 StartUp 13.5599891 -54.5000000 -0.000402 -4.02 2 Minutes 13.5599936 -59.0000000 -0.000435 -4.35 T=-20°C 5 Minutes 13.5599979 -63.3000000 -0.000467 -4.67 10 Minutes 13.560001 -66.4000000 -0.000490 -4.90 Remark: 1.) For further details please refer diagrams in separate annex A1 VERDICT: Pass TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 19 of 25 Variation in the Supply Voltage at Temperature of 20°C Frequency error (tolerance) §15.225 & RSS 210 Set- up no.2 EUT OP-mode no. 2 Nominal Conditions Vnom = 12.V DC Reference Limit-> (from AE3) 13.5599346 MHz 1355.99346 Hz Tnom = 20°C frequency 100ppm: Extreme Voltage Conditions of Rated Primary Supply Voltage Measurement period Frequency Supply Voltage Frequency Error after power- measured up the EUT [MHz] [Hz] [%] [ppm] on StartUp 13.5599253 9.3000000 0.000069 0.69 85% of Rated Primary 2 Minutes 13.5599250 9.6000000 0.000071 0.71 Supply Voltage 5 Minutes 13.5599246 10.0000000 0.000074 0.74 (AE3: 108 V AC / 60 Hz) 10 Minutes 13.5599247 9.9000000 0.000073 0.73 115% of Rated on StartUp 13.5599269 7.7000000 0.000057 0.57 Primary Supply 2 Minutes 13.5599252 9.4000000 0.000069 0.69 Voltages 5 Minutes 13.5599241 10.5000000 0.000077 0.77 (AE3: 138 V AC / 60 Hz) 10 Minutes 13.5599238 10.8000000 0.000080 0.80 Remark: 1.) For further details please refer diagrams in separate annex A1 VERDICT: Pass TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 20 of 25 5.6. Measurement uncertainties The reported uncertainties are calculated based on the standard uncertainty multiplied with the appropriate coverage factor k, such that a confidence level of approximately 95% is achieved. For uncertainty determination, each component used in the concrete measurement set-up was taken in account and it contribution to the overall uncertainty according it’s statistical distribution calculated. Calculated uncertainty based RF-Measurement Reference Frequency range Remarks on a confidence level of 95% Conducted emissions 9 kHz - 150 kHz 4.0 dB CISPR 16-2-1 - (U CISPR) 150 kHz - 30 MHz 3.6 dB Radiated emissions 30 MHz - 1 GHz 4.2 dB CISPR 16-2-3 E-Field Enclosure 1 GHz - 18 GHz 5.1 dB Disturbance power CISPR 16-2-2 30 MHz - 300 MHz - - Power Output radiated - 30 MHz - 4 GHz 3.17 dB Substitution Power Output conducted - 9 kHz - 20 GHz 1.0 dB - Conducted emissions - 9 kHz - 20 GHz 1.0 dB - on antenna ports 20 GHz - 40 GHz 0.1272 ppm (Delta Marker) Frequency error Occupied bandwidth - 9 kHz - 4 GHz 1.0 dB Power - 0.1272 ppm (Delta Marker) Frequency error Emission bandwidth 9 kHz - 4 GHz - 1.0 dB Power Frequency stability - 9 kHz - 20 GHz 0.0636 ppm - 150 kHz - 30 MHz 5.0 dB Magnetic field Radiated emissions - 30 MHz - 1 GHz 4.2 dB E-field Enclosure 1 GHz - 20 GHz 3.17 dB Substitution Table: measurement uncertainties, valid for conducted/radiated measurements TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 21 of 25 6. Accreditation details of CETECOM’s laboratories and test sites Ref.- Accreditation Valid for laboratory area or test site No. Certificate Accreditation Body - D-PL- DAkkS, Deutsche All laboratories and test sites of CETECOM GmbH, Essen 12047-01-01 Akkreditierungsstelle GmbH 337 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) FCC, Federal Communications 487 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) MRA US-EU Commission 558 Radiated Measurements above 1 GHz, 3 m (FAR) 0003 Laboratory Division, USA 348 Mains Ports Conducted Interference Measurements 348 Telecommunication Ports Conducted Interference Measurem. 337 3462D-1 Radiated Measurements 30 MHz to 1 GHz, 3 m / 10 m (OATS) 487 3462D-2 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) IC, Industry Canada Certification 550 3462D-2 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) and Engineering Bureau 558 3462D-3 Radiated Measurements above 1 GHz, 3 m (FAR) 487 R-2666 Radiated Measurements 30 MHz to 1 GHz, 3 m (SAR) VCCI, Voluntary Control Council 550 G-301 Radiated Measurements 1 GHz to 6 GHz, 3 m (SAR) for Interference by Information 348 C-2914 Mains Ports Conducted Interference Measurements Technology Equipment, Japan 348 T-1967 Telecommunication Ports Conducted Interference Measurem. OATS = Open Area Test Site, SAR = Semi Anechoic Room, FAR = Fully Anechoic Room TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 22 of 25 7. Instruments and Ancillary 7.1. Used equipment “CTC” The “Ref.-No” in the left column of the following tables allows the clear identification of the laboratory equipment. 7.1.1. Test software and firmware of equipment Ref.-No. Equipment Type Serial-No. Version of Firmware or Software during the test 001 EMI Test Receiver ESS 825132/017 Firm.= 1.21 , OTP=2.0, GRA=2.0 012 Signal Generator (EMS-cond.) SMY 01 839069/027 Firm.= V 2.02 013 Power Meter (EMS cond.) NRVD 839111/003 Firm.= V 1.51 017 Digital Radiocommunication Tester CMD 60 M 844365/014 Firmware = V 3.52 .22.01.99, DECT = D2.87 13.01.99 053 Audio Analyzer UPA3 860612/022 Firm. V 4.3 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 Firm.= V 3.1DHG 140 Signal Generator SMHU 831314/006 Firm.= 3.21 261 Thermal Power Sensor NRV-Z55 825083/0008 EPROM-Datum 02.12.04, SE EE 1 B 262 Power Meter NRV-S 825770/0010 Firm.= 2.6 263 Signal Generator SMP 04 826190/0007 Firm.=3.21 UNIT Firmware= 4.04, SW-Main=4.04, SW-BBP=1.04, 295 Racal Digital Radio Test Set 6103 1572 SW-DSP=1.02, Hardboot=1.02, Softboot=2.02 R&S Test Firmware =3.53 /3.54 (current Testsoftw. f. 298 Univ. Radio Communication Tester CMU 200 832221/091 all band used 323 Digital Radiocommunication Tester CMD 55 825878/0034 Firm.= 3.52 .22.01.99 335 CTC-EMS-Conducted System EMS Conducted - EMC 32 V 8.52 340 Digital Radiocommunication Tester CMD 55 849709/037 Firm.= 3.52 .22.01.99 355 Power Meter URV 5 891310/027 Firm.= 1.31 365 10V Insertion Unit 50 Ohm URV5-Z2 100880 Eprom Data = 31.03.08 366 Ultra Compact Simulator UCS 500 M4 V0531100594 Firm. UCS 500=001925/3.06a02, rc=ISMIEC 4.10 371 Bluetooth Tester CBT32 100153 CBT V5,30+ SW-Option K55, K57 377 EMI Test Receiver ESCS 30 100160 Firm.= 2.30, OTP= 02.01, GRA= 02.36 378 Broadband RF Field Monitor RadiSense III 03D00013SNO-08 Firm.= V.03D13 389 Digital Multimeter Keithley 2000 0583926 Firm. = A13 (Mainboard) A02 (Display) Firm.= 4.50 #005, IPL=4.01#001,OS=4.02#001, 392 Radio Communication Tester MT8820A 6K00000788 GSM=4.41#013, W-CDMA= 4.54#004, scenario= 4.52#002 R&S Test Firmware Base=5.14, Mess-Software= 436 Univ. Radio Communication Tester CMU 200 103083 GSM:5.14 WCDMA:5.14 (current Testsoftw. F. all band 441 CTC-SAR-EMI Cable Loss System EMI field (SAR) - EMC 32 Version 8.52 442 CTC-SAR-EMS System EMS field (SAR) - EMC 32 Version 8.40 System CTC-FAR-EMI- 443 CTC-FAR-EMI-RSE - Spuri 7.2.5 or EMC 32 Ver. 9.15.00 RSE 444 CTC-FAR-EMS field System-EMS-Field (FAR) - EMC 32 Version 9.15.00 R&S Test Firmware Base=5.14, GSM=5.14 460 Univ. Radio Communication Tester CMU 200 108901 WCDMA=5.14 (current Testsoftw.,f. all band to be used, 489 EMI Test Receiver ESU40 1000-30 Firmware=4.43 SP3, Bios=V5.1-16-3, Spec. =01.00 491 ESD Simulator dito ESD dito dito307022 V 2.30 524 Voltage Drop Simulator VDS 200 0196-16 Software Nr: 000037 Version V4.20a01 526 Burst Generator EFT 200 A 0496-06 Software Nr. 000034 Version V2.32 527 Micro Pulse Generator MPG 200 B 0496-05 Software-Nr. 000030 Version V2.43 528 Load Dump Simulator LD 200B 0496-06 Software-Nr. 000031 Version V2.35a01 R&S Test Firmware Base=5.14, GSM=5.14 546 Univ. Radio Communication Tester CMU 200 106436 WCDMA=5.14 (current Testsoftw.,f. all band to be used R&S Test Firmware Base=V5.1403 (current Testsoftw., 547 Univ. Radio Communication Tester CMU 200 835390/014 f. all band used, GSM = 5.14 WCDMA: = 5.14 584 Spectrum Analyzer FSU 8 100248 2.82_SP3 R&S Test Firmware Base=5.01, GSM=5.02 WCDMA= 597 Univ. Radio Communication Tester CMU 200 100347 not installed, Mainboard= µP1=V.850 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Firmware Bios 3.40 , Analyzer 3.40 Sp 2 620 EMI Test Receiver ESU 26 100362 4.43_SP3 642 Wideband Radio Communication Tester CMW 500 126089 Setup V03.26, Test programm component V03.02.20 670 Univ. Radio Communication Tester CMU 200 106833 µP1 =V8.50, Firmware = V.20 689 Vector Signal Generator SMU200 100970 02.20.360.142 CBT V 5.40, FW: V.2.41 (FPGA Digital, V. 3.09 FPGA 692 Bluetooth Tester CBT 32 100236 RF) TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 23 of 25 7.1.2. Single instruments and test systems Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 001 EMI Test Receiver ESS 825132/017 Rohde & Schwarz 12 M - 30.05.2017 005 AC - LISN (50 Ohm/50µH, test site 1) ESH2-Z5 861741/005 Rohde & Schwarz 12 M - 30.05.2017 007 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 892563/002 Rohde & Schwarz 12 M - 30.05.2017 009 Power Meter (EMS-radiated) NRV 863056/017 Rohde & Schwarz 24 M - 30.04.2017 016 Line Impedance Simulating Network Op. 24-D B6366 Spitzenberger+Spies 36 M - 30.05.2019 020 Horn Antenna 18 GHz (Subst 1) 3115 9107-3699 EMCO 36/12 M - 31.03.2017 021 Loop Antenna (H-Field) 6502 9206-2770 EMCO 36 M - 30.04.2018 030 Loop Antenna (H-field) HFH-Z2 879604/026 Rohde & Schwarz 36 M - 30.04.2018 033 RF-current probe (100kHz-30MHz) ESH2-Z1 879581/18 Rohde & Schwarz 24 M - 30.04.2017 057 relay-switch-unit (EMS system) RSU 494440/002 Rohde & Schwarz pre-m 1a 060 power amplifier (DC-2kHz) PAS 5000 B6363 Spitzenberger+Spies - 3 WRCT 1900/2200-5/40- 066 notch filter (WCDMA; FDD1) 5 Wainwright GmbH 12 M 1g 30.06.2016 10EEK 086 DC - power supply, 0 -10 A LNG 50-10 - Heinzinger Electronic pre-m 2 087 DC - power supply, 0 -5 A EA-3013 S - Elektro Automatik pre-m 2 091 USB-LWL-Converter OLS-1 007/2006 Ing. Büro Scheiba - 4 099 passive voltage probe ESH2-Z3 299.7810.52 Rohde & Schwarz 36 M - 30.04.2018 100 passive voltage probe Probe TK 9416 without Schwarzbeck 36 M - 30.04.2018 110 USB-LWL-Converter OLS-1 - Ing. Büro Scheiba - 4 119 RT Harmonics Analyzer dig. Flickermeter B10 G60547 BOCONSULT 36 M - 30.05.2019 136 adjustable dipole antenna (Dipole 1) 3121C-DB4 9105-0697 EMCO 36 M - 30.04.2018 140 Signal Generator SMHU 831314/006 Rohde & Schwarz 24 M - 30.05.2018 248 attenuator SMA 6dB 2W - Radiall pre-m 2 249 attenuator SMA 10dB 10W - Radiall pre-m 2 252 attenuator N 6dB 12W - Radiall pre-m 2 256 attenuator SMA 3dB 2W - Radiall pre-m 2 257 hybrid 4031C 04491 Narda pre-m 2 260 hybrid coupler 4032C 11342 Narda pre-m 2 261 Thermal Power Sensor NRV-Z55 825083/0008 Rohde & Schwarz 24 M - 30.05.2018 262 Power Meter NRV-S 825770/0010 Rohde & Schwarz 24 M - 30.05.2018 263 Signal Generator SMP 04 826190/0007 Rohde & Schwarz 36 M - 30.05.2019 265 peak power sensor NRV-Z33, Model 04 840414/009 Rohde & Schwarz 24 M - 30.05.2018 266 Peak Power Sensor NRV-Z31, Model 04 843383/016 Rohde & Schwarz 24 M - 30.05.2018 267 notch filter GSM 850 WRCA 800/960-6EEK 9 Wainwright GmbH pre-m 2 270 termination 1418 N BB6935 Weinschel pre-m 2 271 termination 1418 N BE6384 Weinschel pre-m 2 272 attenuator (20 dB) 50 W Model 47 BF6239 Weinschel pre-m 2 273 attenuator (10 dB) 100 W Model 48 BF9229 Weinschel pre-m 2 274 attenuator (10 dB) 50 W Model 47 (10 dB) 50 W BG0321 Weinschel pre-m 2 275 DC-Block Model 7003 (N) C5129 Weinschel pre-m 2 276 DC-Block Model 7006 (SMA) C7061 Weinschel pre-m 2 279 power divider 1515 (SMA) LH855 Weinschel pre-m 2 287 pre-amplifier 25MHz - 4GHz AMF-2D-100M4G-35-10P 379418 Miteq 12 M 1c 30.06.2017 291 high pass filter GSM 850/900 WHJ 2200-4EE 14 Wainwright GmbH 12 M 1c 30.06.2017 298 Univ. Radio Communication Tester CMU 200 832221/091 Rohde & Schwarz pre-m 3 300 AC LISN (50 Ohm/50µH, 1-phase) ESH3-Z5 892 239/020 Rohde & Schwarz 12 M - 30.05.2017 301 attenuator (20 dB) 50W, 18GHz 47-20-33 AW0272 Lucas Weinschel pre-m 2 302 horn antenna 40 GHz (Meas 1) BBHA9170 155 Schwarzbeck 36 M - 31.03.2017 303 horn antenna 40 GHz (Subst 1) BBHA9170 156 Schwarzbeck 36 M - 31.03.2017 331 Climatic Test Chamber -40/+80 Grad HC 4055 43146 Heraeus Vötsch Pre-m 2 341 Digital Multimeter Fluke 112 81650455 Fluke 24 M - 30.05.2018 342 Digital Multimeter Voltcraft M-4660A IB 255466 Voltcraft 24 M - 30.04.2017 347 laboratory site radio lab. - - - 5 348 laboratory site EMI conducted - - - 5 354 DC - Power Supply 40A NGPE 40/40 448 Rohde & Schwarz pre-m 2 355 Power Meter URV 5 891310/027 Rohde & Schwarz 24 M - 30.05.2018 357 power sensor NRV-Z1 861761/002 Rohde & Schwarz 24 M - 30.04.2017 371 Bluetooth Tester CBT32 100153 R&S 36 M - 30.05.2019 373 Single-Line V-Network (50 Ohm/5µH) ESH3-Z6 100535 Rohde & Schwarz 12 M - 30.05.2017 377 EMI Test Receiver ESCS 30 100160 Rohde & Schwarz 12 M - 30.05.2017 389 Digital Multimeter Keithley 2000 0583926 Keithley 24 M - 30.04.2017 392 Radio Communication Tester MT8820A 6K00000788 Anritsu 12 M - 30.05.2017 431 Model 7405 Near-Field Probe Set 9305-2457 EMCO - 4 436 Univ. Radio Communication Tester CMU 200 103083 Rohde & Schwarz 12 M - 30.04.2017 439 UltraLog-Antenna HL 562 100248 Rohde & Schwarz 36 M - 31.03.2017 System CTC-FAR-EMI- ETS-Lindgren / 443 CTC-FAR-EMI-RSE - 12 M 5 30.06.2017 RSE CETECOM WRCT 1850.0/2170.0- Wainwright Instruments 448 notch filter WCDMA_FDD II 5 12 M 1c 30.06.2017 5/40- GmbH WRCT 824.0/894.0-5/40- 449 notch filter WCDMA FDD V 1 Wainwright 12 M 1c 30.06.2017 8SSK TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 24 of 25 Ref.-No. calibration Interval of Remark Equipment Type Serial-No. Manufacturer Cal due 454 Oscilloscope HM 205-3 9210 P 29661 Hameg - 4 456 DC-Power supply 0-5 A EA 3013 S 207810 Elektro Automatik pre-m 2 459 DC -Power supply 0-5 A , 0-32 V EA-PS 2032-50 910722 Elektro Automatik pre-m 2 460 Univ. Radio Communication Tester CMU 200 108901 Rohde & Schwarz 12 M - 30.04.2017 463 Universal source HP3245A 2831A03472 Agilent - 4 466 Digital Multimeter Fluke 112 89210157 Fluke USA 24 M - 30.05.2018 467 Digital Multimeter Fluke 112 89680306 Fluke USA 36 M - 30.04.2018 468 Digital Multimeter Fluke 112 90090455 Fluke USA 36 M - 30.04.2018 477 ReRadiating GPS-System AS-47 - Automotive Cons. Fink - 3 480 power meter (Fula) NRVS 838392/031 Rohde & Schwarz 24 M - 30.04.2017 482 filter matrix Filter matrix SAR 1 - CETECOM (Brl) - 1d AMF-5D-02501800-25- 484 pre-amplifier 2,5 - 18 GHz 1244554 Miteq 12 M - 30.06.2017 10P System EMI field (SAR) ETS Lindgren / 487 System CTC NSA-Verification SAR-EMI - 24 M - 31.07.2017 NSA CETECOM 489 EMI Test Receiver ESU40 1000-30 Rohde & Schwarz 12 M - 30.05.2017 WRCG 1709/1786- 502 band reject filter SN 9 Wainwright pre-m 2 1699/1796- 503 band reject filter WRCG 824/849-814/859- SN 5 Wainwright pre-m 2 WRCA 800/960-02/40- 512 notch filter GSM 850 SN 24 Wainwrght 12 M 1c 30.06.2017 6EEK 517 relais switch matrix HF Relais Box Keithley SE 04 Keithley pre-m 2 523 Digital Multimeter L4411A MY46000154 Agilent 24 M - 30.04.2017 529 6 dB Broadband resistive power divider Model 1515 LH 855 Weinschel pre-m 2 530 10 dB Broadband resistive power divider R 416110000 LOT 9828 - pre-m 2 546 Univ. Radio Communication Tester CMU 200 106436 R&S 12 M - 30.05.2017 547 Univ. Radio Communication Tester CMU 200 835390/014 Rohde & Schwarz 12 M - 30.04.2017 549 Log.Per-Antenna HL025 1000060 Rohde & Schwarz 36/12 M - 31.07.2018 System CTC S-VSWR Verification SAR- System EMI Field SAR S- ETS 550 - 24 M - 31.07.2017 EMI VSWR Lindgren/CETECOM 552 high pass filter 2,8-18GHz WHKX 2.8/18G-10SS 4 Wainwright 12 M 1c 30.06.2017 557 System CTC-OTA-2 R&S TS8991 - Rohde & Schwarz 12 M 5 30.09.2016 System CTC FAR S- 558 System CTC FAR S-VSWR - CTC 24 M - 19.04.2017 VSWR 574 Biconilog Hybrid Antenna BTA-L 980026L Frankonia 36/12 M - 31.03.2019 584 Spectrum Analyzer FSU 8 100248 Rohde & Schwarz pre-m - 594 Wideband Radio Communication Tester CMW 500 101757 Rohde & Schwarz 12 M - 30.04.2017 597 Univ. Radio Communication Tester CMU 200 100347 Rohde & Schwarz pre-m - 598 Spectrum Analyzer FSEM 30 (Reserve) 831259/013 Rohde & Schwarz 24 M - 30.04.2017 600 power meter NRVD (Reserve) 834501/018 Rohde & Schwarz 24 M - 30.04.2017 601 medium-sensitivity diode sensor NRV-Z5 (Reserve) 8435323/003 Rohde & Schwarz 24 M - 30.04.2017 602 peak power sensor NRV-Z32 (Reserve) 835080 Rohde & Schwarz 24 M - 611 DC power supply E3632A KR 75305854 Agilent pre-m 2 612 DC power supply E3632A MY 40001321 Agilent pre-m 2 613 Attenuator R416120000 20dB 10W Lot. 9828 Radiall pre-m 2 616 Digitalmultimeter Fluke 177 88900339 Fluke 24 M - 30.05.2018 617 Power Splitter/Combiner ZFSC-2-2-S+ S F987001108 Mini Circuits - 2 618 Power Splitter/Combiner 50PD-634 600994 JFW Industries USA - 2 619 Power Splitter/Combiner 50PD-634 600995 JFW Industries, USA - 3 620 EMI Test Receiver ESU 26 100362 Rohde-Schwarz 12 M - 30.05.2017 621 Step Attenuator 0-139 dB RSP 100017 Rohde & Schwarz pre-m 2 625 Generic Test Load USB Generic Test Load USB - CETECOM - 2 201.0999.9302.6.4.1.4 627 data logger OPUS 1 G. Lufft GmbH 24 M - 30.04.2017 3 634 Spectrum Analyzer FSM (HF-Unit) 826188/010 Rohde & Schwarz pre-m 2 HDMI cable with Ethernet 637 High Speed HDMI with Ethernet 1m - KogiLink - 2 1m 638 HDMI Kabel with Ethernet 1,5 m flach HDMI cable with Ethernet - Reichelt - 2 640 HDMI cable 2m rund HDMI cable 2m rund - Reichelt - 2 641 HDMI cable with Ethernet Certified HDMI cable with - PureLink - 2 644 Amplifierer ZX60-2534M+ SN865701299 Mini-Circuits - - 670 Univ. Radio Communication Tester CMU 200 106833 Rohde & Schwarz 24 M - 30.05.2018 671 DC-power supply 0-5 A EA-3013S - Elektro Automatik pre-m 2 678 Power Meter NRP 101638 Rohde&Schwarz pre-m - 683 Spectrum Analyzer FSU 26 200571 Rohde & Schwarz 12 M - 30.05.2017 Narda Safety Test 686 Field Analyzer EHP-200A 160WX30702 24 M - 30.04.2017 Solutions 687 Signal Generator SMF 100A 102073 Rohde&Schwarz 12 M - 30.05.2017 688 Pre Amp JS-18004000-40-8P 1750117 Miteq pre-m - 690 Spectrum Analyzer FSU 100302/026 Rohde&Schwarz 12 M - 30.05.2017 692 Bluetooth Tester CBT 32 100236 Rohde & Schwarz 36 M - 31.03.2017 697 Power Splitter ZN4PD-642W-S+ 165001445 Mini-Circuits - 2 TR2-20842790-15-11a

Test Report 2-20842790-15-11a, Page 25 of 25 7.1.3. Legend Note / remarks Calibrated during system calibration: 1a System CTC-SAR-EMS (Ref.-No. 442) 1b System-CTC-EMS-Conducted (Ref.-No. 335) 1c System CTC-FAR-EMI-RSE (Ref.-No . 443) 1d System CTC-SAR-EMI (Ref.-No . 441) 1e System CTC-OATS (EMI radiated) (Ref.-No. 337) 1f System CTC-CTIA-OTA (Ref.-No . 420) 1g System CTC-FAR-EMS (Ref.-No . 444) 2 Calibration or equipment check immediately before measurement 3 Regulatory maintained equipment for functional check or support purpose 4 calibration of this equipment Ancillary equipment without has no effect calibration onmechanical e.g. measuring result equipment or monitoring equipment 5 Test System Interval of calibration 12 M 12 month 24 M 24 month 36 M 36 month 24/12 M Calibration every 24 months, between this every 12 months internal validation 36/12 M Calibration every 36 months, between this every 12 months internal validation Pre-m Check before starting the measurement - Without calibration 8. Versions of test reports (change history) Version Applied changes Date of release -- Initial release 2016-12-05 -- -- -- TR2-20842790-15-11a


Document Created: 2016-12-05 10:33:13
Document Modified: 2016-12-05 10:33:13
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC