Test Report Widex

FCC ID: TVUW570H

Test Report

Download: PDF
FCCID_4161207

                                                          TEST REPORT
                                                Test report no.: 1-6814/18-01-05                                               D-PL-12076-01-03




                  Testing laboratory                                                          Applicant
 CTC advanced GmbH                                                          Gigaset Communications GmbH
 Untertuerkheimer Strasse 6 – 10                                            Frankenstr. 2
 66117 Saarbruecken / Germany                                               46395 Bocholt / GERMANY
 Phone:    + 49 681 5 98 - 0                                                Phone:    +49 2871 91-0
 Fax:      + 49 681 5 98 - 9075                                             Contact: Uwe Alt
 Internet: http://www.ctcadvanced.com                                       e-mail:   uwe.alt@gigaset.com
 e-mail:   mail@ctcadvanced.com                                             Phone:    +49 287 191-2857
 Accredited Testing Laboratory:
 The testing laboratory (area of testing) is accredited
 according to DIN EN ISO/IEC 17025 (2005) by the
 Deutsche Akkreditierungsstelle GmbH (DAkkS)                                                Manufacturer
 The accreditation is valid for the scope of testing                        Gigaset Communications GmbH
 procedures as stated in the accreditation certificate with                 Frankenstr. 2
 the registration number: D-PL-12076-01-03                                  46395 Bocholt / GERMANY


                                                               Test standard/s
 FCC - Title 47 CFR            FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio
 Part 15                       frequency devices
 RSS - 210 Issue 9             Spectrum Management and Telecommunications Radio Standards Specification -
                               Licence-Exempt Radio Apparatus: Category I Equipment
 RSS - Gen Issue 5             Spectrum Management and Telecommunications Radio Standards Specification
                               - General Requirements for Compliance of Radio Apparatus
 For further applied test standards please refer to section 3 of this test report.

                                                                     Test Item
 Kind of test item:           DECT Handset with hearing aid function
 Model name:                  W570H
 FCC ID:                      TVU-W570H
 IC:                          8023A-W570H
 Frequency:                   10.6 MHz
 Technology tested:           WIDEX
 Antenna:                     Integrated coil antenna
 Power supply:                2.2 V to 2.9 V DC by 2 NIMH batteries type AAA
 Temperature range:           0°C to +45°C

This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures,
the public keys can be requested at the testing laboratory.

 Test report authorized:                                                  Test performed:
                               cn=Christoph Schneider, o=CTC advanced                              cn=Tobias Wittenmeier, o=CTC advanced
                               GmbH, ou=SND-161128,                                                GmbH, ou=WIT-170519,
                               email=Christoph.Schneider@ctcadvanced.c                             email=tobias.wittenmeier@ctcadvanced.com,
                               om, c=DE                                                            c=DE
                               2019.01.30 13:01:50 +01'00'                                         2019.01.30 13:57:43 +01'00'

 Christoph Schneider                                                      Tobias Wittenmeier
 Lab Manager                                                              Testing Manager
 Radio Communications & EMC                                               Radio Communications & EMC


                    Test report no.: 1-6814/18-01-05




1      Table of contents

1    Table of contents ............................................................................................................................................ 2
2    General information ....................................................................................................................................... 3
     2.1       Notes and disclaimer .......................................................................................................................... 3
     2.2       Application details ............................................................................................................................... 3
     2.3       Test laboratories sub-contracted ...................................................................................................... 3
3    Test standard/s and references .................................................................................................................... 4
4    Test environment............................................................................................................................................ 5
5    Test item .......................................................................................................................................................... 5
     5.1       General description ............................................................................................................................. 5
     5.2       Additional information ........................................................................................................................ 5
6    Description of the test setup ......................................................................................................................... 6
     6.1       Shielded semi anechoic chamber ...................................................................................................... 7
     6.2       Shielded fully anechoic chamber ...................................................................................................... 8
     6.3       Test setup for normalized measurement configurations ................................................................ 9
7    Sequence of testing .....................................................................................................................................10
     7.1       Sequence of testing radiated spurious 9 kHz to 30 MHz ...............................................................10
     7.2       Sequence of testing radiated spurious 30 MHz to 1 GHz ..............................................................11
8    Measurement uncertainty ............................................................................................................................12
9    Summary of measurement results .............................................................................................................13
10      Additional comments ...............................................................................................................................14
11      Measurement results ................................................................................................................................15
     11.1          Field strength of the fundamental ................................................................................................15
     11.2          Emission bandwidth (6 dB bandwidth)........................................................................................16
     11.3          Occupied bandwidth......................................................................................................................17
     11.4          Field strength of the harmonics and spurious ...........................................................................18
12      Observations .............................................................................................................................................22
Annex A            Glossary ..........................................................................................................................................23
Annex B            Document history ..........................................................................................................................24
Annex C            Accreditation Certificate ...............................................................................................................24




© CTC advanced GmbH                                                                                                                                      Page 2 of 24


              Test report no.: 1-6814/18-01-05




2      General information

2.1    Notes and disclaimer
The test results of this test report relate exclusively to the test item specified in this test report. CTC advanced
GmbH does not assume responsibility for any conclusions and generalizations drawn from the test results with
regard to other specimens or samples of the type of the equipment represented by the test item.
The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report
requires the prior written approval of CTC advanced GmbH.
The testing service provided by CTC advanced GmbH has been rendered under the current "General Terms and
Conditions for CTC advanced GmbH".
CTC advanced GmbH will not be liable for any loss or damage resulting from false, inaccurate, inappropriate or
incomplete product information provided by the customer.
Under no circumstances does the CTC advanced GmbH test report include any endorsement or warranty
regarding the functionality, quality or performance of any other product or service provided.
Under no circumstances does the CTC advanced GmbH test report include or imply any product or service
warranties from CTC advanced GmbH, including, without limitation, any implied warranties of merchantability,
fitness for purpose, or non-infringement, all of which are expressly disclaimed by CTC advanced GmbH.
All rights and remedies regarding vendor’s products and services for which CTC advanced GmbH has prepared
this test report shall be provided by the party offering such products or services and not by CTC advanced GmbH.
In no case this test report can be considered as a Letter of Approval.

This test report is electronically signed and valid without handwritten signature. For verification of the electronic
signatures, the public keys can be requested at the testing laboratory.



2.2    Application details
Date of receipt of order:                2018-09-26
Date of receipt of test item:            2018-10-09
Start of test:                           2018-10-09
End of test:                             2018-10-10
Person(s) present during the test:       -/-



2.3    Test laboratories sub-contracted
None




 © CTC advanced GmbH                                                                                     Page 3 of 24


            Test report no.: 1-6814/18-01-05




3    Test standard/s and references
Test standard             Date          Description
FCC - Title 47 CFR Part                 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part
15                                      15 - Radio frequency devices
RSS - 210 Issue 9         August 2016   Spectrum Management and Telecommunications Radio Standards
                                        Specification - Licence-Exempt Radio Apparatus: Category I
                                        Equipment
RSS - Gen Issue 5         April 2018    Spectrum Management and Telecommunications Radio Standards
                                        Specification
                                        - General Requirements for Compliance of Radio Apparatus



Guidance                  Version       Description

                                        American national standard for methods of measurement of radio-
ANSI C63.4-2014           -/-           noise emissions from low-voltage electrical and electronic
                                        equipment in the range of 9 kHz to 40 GHz
                                        American national standard of procedures for compliance testing
ANSI C63.10-2013          -/-
                                        of unlicensed wireless devices




© CTC advanced GmbH                                                                             Page 4 of 24


              Test report no.: 1-6814/18-01-05




4     Test environment

                                   Tnom    +22 °C during room temperature tests
Temperature                  :     Tmax    +45 °C during high temperature tests
                                   Tmin     0   °C during low temperature tests
Relative humidity content    :             55 %
Barometric pressure          :             1021 hpa
                                   Vnom    2.5 V DC by 2 NIMH batteries type AAA
Power supply                 :     Vmax    2.9 V
                                   Vmin    2.2 V



5     Test item

5.1   General description

Kind of test item            :   DECT Handset with hearing aid function
Type identification          :   W570H
HMN                          :   -/-
PMN                          :   Gigaset W570A
HVIN                         :   Gigaset W570H
FVIN                         :   -/-
S/N serial number            :   No information available
Hardware status              :   S30852-Q2757-R301
Software status              :   No information available
Firmware status              :   No information available
Frequency band               :   10.6 MHz
Type of radio transmission   :
                                 Modulated carrier
Use of frequency spectrum    :
Type of modulation           :   FSK
Number of channels           :   1
Antenna                      :   Integrated coil antenna
Power supply                 :   2.2 V to 2.9 V DC by 2 NIMH batteries type AAA
Temperature range            :   0°C to +45°C


5.2   Additional information
The content of the following annexes is defined in the QA. It may be that not all of the listed annexes are
necessary for this report, thus some values in between may be missing.

Test setup and EUT photos are included in test report:          1-6814/18-01-05_AnnexA
                                                                1-6814/18-01-05_AnnexB
                                                                1-6814/18-01-05_AnnexD




 © CTC advanced GmbH                                                                                   Page 5 of 24


                   Test report no.: 1-6814/18-01-05




6           Description of the test setup
Typically, the calibrations of the test apparatus are commissioned to and performed by an accredited calibration
laboratory. The calibration intervals are determined in accordance with the DIN EN ISO/IEC 17025. In addition to
the external calibrations, the laboratory executes comparison measurements with other calibrated test systems
or effective verifications. Weekly chamber inspections and range calibrations are performed. Where possible, RF
generating and signaling equipment as well as measuring receivers and analyzers are connected to an external
high-precision 10 MHz reference (GPS-based or rubidium frequency standard).

In order to simplify the identification of the equipment used at some special tests, some items of test equipment
and ancillaries can be provided with an identifier or number in the equipment list below (Lab/Item).



Agenda: Kind of Calibration

    k        calibration / calibrated                     EK    limited calibration
    ne       not required (k, ev, izw, zw not required)   zw    cyclical maintenance (external cyclical
                                                                maintenance)
    ev       periodic self verification                   izw   internal cyclical maintenance
    Ve       long-term stability recognized               g     blocked for accredited testing
    vlkI!    Attention: extended calibration interval
    NK!      Attention: not calibrated                    *)    next calibration ordered / currently in progress




 © CTC advanced GmbH                                                                                      Page 6 of 24


               Test report no.: 1-6814/18-01-05




6.1   Shielded semi anechoic chamber
The radiated measurements are performed in vertical and horizontal plane in the frequency range from 30 MHz
to 1 GHz in semi-anechoic chambers. The EUT is positioned on a non-conductive support with a height of 0.80
m above a conductive ground plane that covers the whole chamber. The receiving antennas are conform to
specifications ANSI C63. These antennas can be moved over the height range between 1.0 m and 4.0 m in order
to search for maximum field strength emitted from EUT. The measurement distances between EUT and receiving
antennas are indicated in the test setups for the various frequency ranges. For each measurement, the EUT is
rotated in all three axes until the maximum field strength is received. The wanted and unwanted emissions are
received by spectrum analyzers where the detector modes and resolution bandwidths over various frequency
ranges are set according to requirement ANSI C63.




Measurement distance: tri-log antenna 10 meter
EMC32 software version: 10.30.0
FS = UR + CL + AF
(FS-field strength; UR-voltage at the receiver; CL-loss of the cable; AF-antenna factor)
Example calculation:
FS [dBµV/m] = 12.35 [dBµV/m] + 1.90 [dB] + 16.80 [dB/m] = 31.05 [dBµV/m] (35.69 µV/m)

Equipment table:

       Lab /                                                                                             Kind of     Last        Next
No.            Equipment                Type               Manufacturer         Serial No.     INV. No.
       Item                                                                                              Calibration Calibration Calibration
1         A         Switch-Unit             3488A                HP              2719A14505    300000368     ev           -/-         -/-
2         A        Meßkabine 1          HF-Absorberhalle    MWB AG 300023                      300000551     ne           -/-         -/-
3         A      EMI Test Receiver          ESCI 3              R&S                 100083     300003312      k      15.12.2018 14.12.2019
               Analyzer-Reference-
                                                                                  A3509 07/0
4        A      System (Harmonics          ARS 16/1               SPS                          300003314     vlKI!    15.01.2018   14.01.2020
                                                                                    0205
                    and Flicker)
5        A        Antenna Tower           Model 2175         ETS-Lindgren           64762      300003745      izw         -/-          -/-
6        A     Positioning Controller     Model 2090         ETS-Lindgren           64672      300003746      izw         -/-          -/-
                Turntable Interface-
7        A                               Model 105637        ETS-Lindgren           44583      300003747      izw         -/-          -/-
                        Box
                TRILOG Broadband
                                                           Schwarzbeck Mess -
8        A     Test-Antenna 30 MHz         VULB9163                                   371      300003854     vlKI!    24.11.2017   23.11.2020
                                                               Elektronik
                      - 3 GHz




 © CTC advanced GmbH                                                                                                            Page 7 of 24


               Test report no.: 1-6814/18-01-05




6.2   Shielded fully anechoic chamber




Measurement distance: loop antenna 3 meter / 1 meter

FS = UR + CA + AF
(FS-field strength; UR-voltage at the receiver; CA-loss of the signal path; AF-antenna factor)

Example calculation:
FS [dBµV/m] = 40.0 [dBµV/m] + (-35.8) [dB] + 32.9 [dB/m] = 37.1 [dBµV/m] (71.61 µV/m)

Equipment table:

       Lab /                                                                                              Kind of     Last        Next
No.            Equipment             Type               Manufacturer           Serial No.     INV. No.
       Item                                                                                               Calibration Calibration Calibration
               Active Loop Antenna
1        A                                   6502             EMCO                  2210      300001015      vlKI!    07.07.2017   06.07.2019
                 9 kHz to 30 MHz
                   4U RF Switch
2        A                                  L4491A      Agilent Technologies    MY50000032    300004510       ne          -/-          -/-
                     Platform
                                        Intel Core i3
                                                                               2V2403033A54
3        A         Computer            3220/3,3 GHz,                                          300004591       ne          -/-          -/-
                                                                                    21
                                         Prozessor
                 NEXIO EMV-              BAT EMC
4        A                                                    EMCO                            300004682       ne          -/-          -/-
                   Software              V3.16.0.49
5        A     Anechoic chamber                                TDK                            300003726       ne          -/-          -/-
               EMI Test Receiver
6        A                                  ESR26              R&S                 101376     300005063       k       14.12.2018   13.12.2019
                9kHz-26,5GHz




 © CTC advanced GmbH                                                                                                            Page 8 of 24


               Test report no.: 1-6814/18-01-05




6.3   Test setup for normalized measurement configurations




FS = UR + CA + AF
(FS-field strength; UR-voltage at the receiver; CA-loss of the signal path; AF-antenna factor)

Example calculation:
FS [dBµV/m] = 40.0 [dBµV/m] + (-35.8) [dB] + 32.9 [dB/m] = 37.1 [dBµV/m] (71.61 µV/m)


Equipment table:

       Lab /                                                                                     Kind of     Last        Next
No.            Equipment             Type           Manufacturer        Serial No.   INV. No.
       Item                                                                                      Calibration Calibration Calibration
               EMI Test Receiver 9
1        A      kHz - 3 GHz incl.           ESPI3         R&S               101713   300004059       k       13.12.2018   12.12.2019
                   Preselector
2        A       Loop Antenna                        ZEG TS Steinfurt                400001208       ev          -/-          -/-
3        A       RF Cable BNC               RG58     Huber & Suhner                  400001209       ev          -/-          -/-




 © CTC advanced GmbH                                                                                                   Page 9 of 24


              Test report no.: 1-6814/18-01-05




7     Sequence of testing

7.1   Sequence of testing radiated spurious 9 kHz to 30 MHz
Setup
   • The equipment is set up to simulate normal operation mode as described in the user manual or defined
      by the manufacturer.
   • If the EUT is a tabletop system, it is placed on a table with 0.8 m height.
   • If the EUT is a floor standing device, it is placed directly on the turn table.
   • Auxiliary equipment and cables are positioned to simulate normal operation conditions as described in
      ANSI C 63.4.
   • The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
   • Measurement distance is 3 m (see ANSI C 63.4) – see test details.
   • EUT is set into operation.

Premeasurement*
   • The turntable rotates from 0° to 315° using 45° steps.
   • The antenna height is 1 m.
   • At each turntable position the analyzer sweeps with positive-peak detector to find the maximum of all
      emissions.

Final measurement
    • Identified emissions during the pre-measurement are maximized by the software by rotating the turntable
       from 0° to 360°.
    • Loop antenna is rotated about its vertical axis for maximum response at each azimuth about the EUT.
       (For certain applications, the loop antenna plane may also need to be positioned horizontally at the
       specified distance from the EUT)
    • The final measurement is done in the position (turntable and elevation) causing the highest emissions
       with quasi-peak (as described in ANSI C 63.4).
    • Final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to the
       limit and limit will be recorded. A plot with the graph of the premeasurement and the limit is stored.

*)Note: The sequence will be repeated three times with different EUT orientations.




 © CTC advanced GmbH                                                                             Page 10 of 24


              Test report no.: 1-6814/18-01-05




7.2   Sequence of testing radiated spurious 30 MHz to 1 GHz
Setup
   • The equipment is set up to simulate normal operation mode as described in the user manual or defined
      by the manufacturer.
   • If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane.
   • If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
   • Auxiliary equipment and cables are positioned to simulate normal operation conditions as described in
      ANSI C 63.4.
   • The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
   • Measurement distance is 10 m or 3 m (see ANSI C 63.4) – see test details.
   • EUT is set into operation.

Premeasurement
   • The turntable rotates from 0° to 315° using 45° steps.
   • The antenna is polarized vertical and horizontal.
   • The antenna height changes from 1 m to 3 m.
   • At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to
      find the maximum of all emissions.

Final measurement
    • The final measurement is performed for at least six highest peaks according to the requirements of the
       ANSI C63.4.
    • Based on antenna and turntable positions at which the peak values are measured the software maximize
       the peaks by changing turntable position ± 45° and antenna height between 1 and 4 m.
    • The final measurement is done with quasi-peak detector (as described in ANSI C 63.4).
    • Final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable angle,
       correction factor, margin to the limit and limit are recorded. A plot with the graph of the premeasurement
       with marked maximum final results and the limit is stored.




 © CTC advanced GmbH                                                                                Page 11 of 24


            Test report no.: 1-6814/18-01-05




8    Measurement uncertainty

                                       Measurement uncertainty
                          Test case                                      Uncertainty
Occupied bandwidth                                          ± used RBW
Field strength of the fundamental                           ± 3 dB
Field strength of the harmonics and spurious                ± 3 dB
Receiver spurious emissions and cabinet radiations          ± 3 dB
Conducted limits                                            ± 2.6 dB




© CTC advanced GmbH                                                                    Page 12 of 24


                  Test report no.: 1-6814/18-01-05




9       Summary of measurement results

    TC Identifier                   Description                    Verdict            Date              Remark
                                    CFR Part 15
     RF-Testing                   RSS Gen Issue 5                  Passed         2019-01-30               -/-
                                  RSS 210 Issue 9


        Test                                                    Power
                                               Temperature
    Specification           Test Case                           Source    C NC NA NP                  Remark
                                                Conditions
       Clause                                                  Voltages
     § 15.223(a)
                          Fieldstrength of
      RSS 210                                        Nominal   Nominal                                   -/-
                           Fundamental
    Issue 9 (B.3)

     § 15.223(a)
                        Emission bandwidth
      RSS 210                                        Nominal   Nominal    -/-   -/-   -/-   -/-          -/-
                         6 dB bandwidth
    Issue 9 (B.3)

      RSS Gen           Occupied bandwidth
                                                     Nominal   Nominal                                   -/-
    Issue 5 (6.6)        99 % bandwidth

      § 15.209/
                          Fieldstrength of
      RSS Gen                                        Nominal   Nominal                                   -/-
                      harmonics and spurious
    Issue 5 (6.13)

      § 15.209
                         Receiver spurious
      RSS Gen                                        Nominal   Nominal                                   -/-
                        emissions (radiated)
    Issue 5 (7.1)

                                                                                                  WIDEX interface
                                                                                                  only available in
      §15.107
                          Conducted limits           Nominal   Nominal                            battery operation
      §15.207
                                                                                                   without charger
                                                                                                     connection


Note: NA = Not Applicable; NP = Not Performed, C = Compliant; NC = Not compliant




 © CTC advanced GmbH                                                                                    Page 13 of 24


              Test report no.: 1-6814/18-01-05




10    Additional comments
Reference documents:          None

Special test descriptions:    None

Configuration descriptions:   None




 © CTC advanced GmbH                             Page 14 of 24


              Test report no.: 1-6814/18-01-05




11    Measurement results

11.1 Field strength of the fundamental
Measurement:

                                          Measurement parameter
                 Detector:                           Quasi peak
                 Sweep time:                         -/-
                 Resolution bandwidth:               9 kHz
                 Video bandwidth:                    ≥ RBW
                 Span:                               -/-
                 Trace-Mode:                         Max Hold
                 Used test setup:                    See chapter 6.2A
                 Measurement uncertainty:            See chapter 8


Limits:

                                                               FCC & IC
             Frequency                                       Field strength                                                            Measurement distance
               (MHz)                                           (dBµV/m)                                                                        (m)
            1.705 – 30.0                                               30                                                                       30


Recalculation:

                                                According to ANSI C63.10
           Frequency                                    Formula                                                                             Correction value
                                                                            𝑑𝑑nearfield                        𝑑𝑑𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙𝑙
                                   FSlimit = FSmax −40 log οΏ½                                   οΏ½ − 20log(                          )
                                                                            π‘‘π‘‘π‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘šπ‘š                𝑑𝑑𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛𝑛

                               FSlimit       is the calculation of field strength at the limit distance,
           10.6 MHz                          expressed in dBµV/m
                                                                                                                                         -42.61 from 1m to 30m
                               FSmax         is the measured field strength, expressed in dBµV/m
                               dnear field   is the λ/2π distance
                               dmeasure      is the distance of the measurement point from EUT
                               dlimit        is the reference limit distance




Results:

            Test conditions                                                       Radiated field strength / (dBµV/m)
              Frequency
                Mode                                at 1 m distance                                  at 30 m distance                        Limit at 30 m distance
      Tnom                 Vnom                               43.3                                                        0.7                         30




 © CTC advanced GmbH                                                                                                                                   Page 15 of 24


              Test report no.: 1-6814/18-01-05




11.2 Emission bandwidth (6 dB bandwidth)
Measurement:

                                         Measurement parameters
                     Detector:                   Peak
                     Resolution bandwidth:       1 % – 5 % of the occupied bandwidth
                     Video bandwidth:            ≥ 3x RBW
                     Trace mode:                 Max hold
                     Used test setup:            See chapter 6.3A
                     Measurement uncertainty:    See chapter 8



Limits:

                                                               FCC

 For the purposes of this Section, bandwidth is determined at the points 6 dB down from the modulated carrier




Results:

                  Test conditions                                                     6 dB bandwidth
           Tnom                          Vnom                                             448 kHz




Plot 1: 6 dB bandwidth

                                                              *RBW 10 kHz   Marker 2 [T1 ]
                                                               VBW 30 kHz              6.03 dBµV
                         Ref   32 dBµV          Att   10 dB    SWT 20 ms        10.828000000 MHz
                         30 Offset -54 dB                                   Marker 1 [T1 ]
                                                                                      13.39 dBµV
                                                                                10.396000000 MHz A
                         20
                                                                            Marker 3 [T1 ]
                  1 PK                                1
                  VIEW
                                                                                       3.97 dBµV
                         10                                                     10.380000000 MHz LVL
                                                                     2
                                 D1 7.39 dBµV         3

                         0


                         -10


                         -20
                                                                                                   3DB

                         -30


                         -40


                         -50


                         -60



                         Center 10.6 MHz                  200 kHz/                    Span 2 MHz




                  Date: 9.OCT.2018       14:24:39




 © CTC advanced GmbH                                                                                     Page 16 of 24


             Test report no.: 1-6814/18-01-05




11.3 Occupied bandwidth
Measurement:

The emission bandwidth (x dB) is defined as the frequency range between two points, one above and one
below the carrier frequency, at which the spectral density of the emission is attenuated x dB below the
maximum in-band spectral density of the modulated signal.

                                            Measurement parameters
                        Detector:                   Peak
                        Resolution bandwidth:       1 % – 5 % of the occupied bandwidth
                        Video bandwidth:            ≥ 3x RBW
                        Trace mode:                 Max hold
                        Analyser function:          99 % power function
                        Used test setup:            See chapter 6.3A
                        Measurement uncertainty:    See chapter 8



Limit:

                               -/-                                                                 IC
                               -/-                                                                 -/-



Result:

                                                    99% emission bandwidth
                                                           652 kHz



Plot 1: 99 % emission bandwidth

                                                              *RBW 10 kHz   Marker 1 [T1 ]
                                                               VBW 30 kHz             14.04 dBµV
                        Ref    32 dBµV         Att   10 dB     SWT 20 ms        10.396000000 MHz
                         30 Offset -54 dB                                   OBW652.000000000 kHz
                                                                            Temp 1 [T1 OBW]
                                                                                      -5.38 dBµV A
                         20
                                                                                10.276000000 MHz
                 1 PK                                 1
                 VIEW
                                                                            Temp 2 [T1 OBW]
                         10                                                           -3.53 dBµV LVL
                                                                                10.928000000 MHz

                         0                                             T2
                                                T1

                         -10


                         -20
                                                                                                   3DB

                         -30


                         -40


                         -50


                         -60



                        Center 10.6 MHz                   200 kHz/                    Span 2 MHz




                 Date: 9.OCT.2018        14:21:07



 © CTC advanced GmbH                                                                                     Page 17 of 24


              Test report no.: 1-6814/18-01-05




11.4 Field strength of the harmonics and spurious
Measurement:

The maximum detected field strength for the harmonics and spurious.

                                            Measurement parameter
                Detector:                                 Average / Quasi Peak
                Sweep time:                               Auto
                                                          F < 150 kHz: 200 Hz
                Resolution bandwidth:                     150 kHz > F > 30 MHz: 9 kHz   9 kHz
                                                          F > 30 MHz: 120 kHz
                                                          F < 150 kHz: 1 kHz
                Video bandwidth:                          150 kHz > F > 30 MHz: 100 kHz 9 kHz
                                                          F > 30 MHz: 300 kHz
                Span:                                     See plots!
                Trace-Mode:                               Max hold
                Used test setup:                          See chapter 6.1A & 6.2A
                Measurement uncertainty:                  See chapter 8



Limit:

                            FCC                                                     IC

                                   Field strength of the harmonics and spurious.

          Frequency / (MHz)                  Field strength / (µV/m)           Measurement distance / (m)
           0.0009 – 0.490                          2400/F(kHz)                             300
            0.490 – 1.705                         24000/F(kHz)                              30
              1.705 – 30                        30 (29.5 dBµV/m)                            30
                30 – 88                         100 (40 dBµv/m)                              3
               88 – 216                        150 (43.5 dBµV/m)                             3
              216 – 960                         200 (46 dBµV/m)                              3



Result:

                                                 Detected emissions
          Frequency                                         Resolution bandwidth
                                        Detector                                          Detected value
            (MHz)                                                   (kHz)
   All emissions were more than 10 dB below the limit. For emissions between 30 MHz and 1 GHz see result
                                           table below the plots.



Note:     The limit was recalculated with 20 dB / decade (Part 15.31) for all radiated spurious emissions 30 MHz
          to 1 GHz from 3 meter limit to a 10 meter distance. (40dB/decade for emissions < 16 MHz and > 16
          MHz according to Ansi C63)



 © CTC advanced GmbH                                                                               Page 18 of 24


                      Test report no.: 1-6814/18-01-05




Plots: TX mode

Plot 1: 9 kHz – 30 MHz; magnetic
         130
dBµV/m
         120

         110

         100

          90

          80

          70

          60

          50

          40

          30

          20

          10
               9kHz                         100k                     1M   10M           30MHz
                                                         Frequency




 © CTC advanced GmbH                                                            Page 19 of 24


                       Test report no.: 1-6814/18-01-05




Plot 2: 30 MHz – 1000 MHz, vertical and horizontal polarization



                              80



                              70



                              60



                              50
            Level in dBµV/m




                                                                                                                       FCC_10m_B

                              40



                              30



                              20



                              10



                              0
                              30M              50   60    80 100M                 200        300     400     500         800   1G
                                                                          Frequency in Hz



Final_Result

    Frequency                      QuasiPeak          Limit     Margin       Meas.      Bandwidth     Height       Pol     Azimuth     Corr.
      (MHz)                        (dBµV/m)         (dBµV/m)     (dB)        Time         (kHz)        (cm)                 (deg)      (dB)
                                                                             (ms)
          36.178                        16.90            30.0     13.10        1000            120         101.0   H           238.0     13.1
          46.636                        17.76            30.0     12.24        1000            120         170.0   H            -5.0     14.0
          63.814                        15.33            30.0     14.67        1000            120         101.0   V           349.0     11.3
         467.283                        21.52            36.0     14.48        1000            120         170.0   V            75.0     18.1
         667.673                        25.39            36.0     10.61        1000            120         170.0   V           241.0     21.5
         926.822                        29.70            36.0      6.30        1000            120         170.0   H            20.0     24.7




 © CTC advanced GmbH                                                                                                            Page 20 of 24


                               Test report no.: 1-6814/18-01-05




Plots: Idle mode

Plot 1: 30 MHz – 1000 MHz, vertical and horizontal polarization



                          80



                          70



                          60



                          50
       Level in dBµV/m




                                                                                                         FCC_10m_B

                          40



                          30



                          20



                          10



                           0
                           30M          50   60    80 100M              200       300   400    500         800   1G
                                                                Frequency in Hz



Final_Result

    Frequency                       QuasiPeak       Limit     Margin    Meas.     Bandwidth     Height     Pol    Azimuth     Corr.
      (MHz)                         (dBµV/m)      (dBµV/m)     (dB)     Time        (kHz)        (cm)              (deg)      (dB)
                                                                        (ms)
                          40.860         17.35         30.0     12.65     1000           120     100.0    V           336.0     13.6
                          52.129         17.63         30.0     12.37     1000           120     170.0    H           284.0     13.8
                          83.917         12.30         30.0     17.70     1000           120      98.0    V           341.0      8.8
                         494.473         22.16         36.0     13.84     1000           120     101.0    V           315.0     18.6
                         697.049         25.72         36.0     10.28     1000           120     170.0    H           198.0     21.7
                         926.448         29.62         36.0      6.38     1000           120     170.0    V            75.0     24.7




 © CTC advanced GmbH                                                                                                   Page 21 of 24


             Test report no.: 1-6814/18-01-05




12    Observations
No observations except those reported with the single test cases have been made.




 © CTC advanced GmbH                                                               Page 22 of 24


            Test report no.: 1-6814/18-01-05




Annex A         Glossary

         EUT    Equipment under test
         DUT    Device under test
         UUT    Unit under test
        GUE     GNSS User Equipment
        ETSI    European Telecommunications Standards Institute
          EN    European Standard
         FCC    Federal Communications Commission
      FCC ID    Company Identifier at FCC
           IC   Industry Canada
        PMN     Product marketing name
        HMN     Host marketing name
        HVIN    Hardware version identification number
        FVIN    Firmware version identification number
        EMC     Electromagnetic Compatibility
          HW    Hardware
          SW    Software
     Inv. No.   Inventory number
   S/N or SN    Serial number
            C   Compliant
          NC    Not compliant
          NA    Not applicable
          NP    Not performed
          PP    Positive peak
          QP    Quasi peak
        AVG     Average
          OC    Operating channel
        OCW     Operating channel bandwidth
        OBW     Occupied bandwidth
        OOB     Out of band
         DFS    Dynamic frequency selection
        CAC     Channel availability check
          OP    Occupancy period
        NOP     Non occupancy period
          DC    Duty cycle
         PER    Packet error rate
          CW    Clean wave
          MC    Modulated carrier
       WLAN     Wireless local area network
       RLAN     Radio local area network
       DSSS     Dynamic sequence spread spectrum
       OFDM     Orthogonal frequency division multiplexing
       FHSS     Frequency hopping spread spectrum
       GNSS     Global Navigation Satellite System
        C/N0    Carrier to noise-density ratio, expressed in dB-Hz



© CTC advanced GmbH                                                  Page 23 of 24


             Test report no.: 1-6814/18-01-05




Annex B        Document history

  Version                                Applied changes                                 Date of release

     -/-                                   Initial release                                 2019-01-30




Annex C        Accreditation Certificate

                       first page                                          last page




Note: The current certificate annex is published on the website (link see below) of the Accreditation
Body DAkkS or may be received by CTC advanced GmbH on request

https://www.dakks.de/as/ast/d/D-PL-12076-01-03e.pdf




################################## END OF TEST REPORT ##################################



 © CTC advanced GmbH                                                                          Page 24 of 24



Document Created: 2019-01-30 13:57:43
Document Modified: 2019-01-30 13:57:43

Β© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC