Users Manual

FCC ID: TV7R11E5HACD

Users Manual

Download: PDF
FCCID_2320088

Federal Communication Commission Interference Statement
(FCC ID: TV7R11E5HACD)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
  connected.
● Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT: Exposure to Radio Frequency Radiation.
The maximum permissible exposure report has been created for this module, which shows the
minimum distances for public use as 260 cm when using a 32-dBi gain antenna. Under such
configuration, the FCC radiation exposure limits set forth for a general population/uncontrolled
environment can be satisfied.

OEM statement. This module is intended for OEM installations only. As such the OEM
integrator is responsible for ensuring that the end-user has no manual instructions to remove
install or modify the module. This module is limited to installations in mobile or fixed
applications. OEM integrators may utilize antennas of like an equal or lesser gain as appearing
in the table below (for further infomraiton on this topic refer to 47CFR, paragraph
15.204(c)(4)). The MikroTik OEM RF Module complies with Part 15 of the FCC rules and
regulations.
OEM Modules have been certified by the FCC for use with other products without any further
certification (as per 47CFR section 2.1091). Separate approval is required for other operating
configurations including portable configurations with respect to 47CFR paragraph 2.1093 and
different antenna configurations. The OEM is required to comply with all 47CFR labeling
instructions and requirements for the finished products.
Changes or modifications not expressly approved by MikroTik could void the OEM authority to
install or operate the equipment. OEMs must test their final product to comply with
unintentional radiators (47CFR section 15.107 and 15.109) before declaring compliance of
their final product to Part 15 of the FCC Rules.

Warning: the OEM must ensure that the end product complies with FCC labeling
requirements. This includes a clearly visible label on the outside of the OEM enclosure
specifying the appropriate MikroTik OEM RF Module FCC identifier for this product as well as
any other required FCC notices as presented below.

Contains FCC ID: TV7R11E5HACD

This enclosed device complies with 47CFR paragraph 15 C of the FCC rules and regulations.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

Labeling and text information should be of a size of type large enough to be readily legible,
consistent with the dimensions of the equipment and the label.


FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This device and its antenna must not be co-located or operation in conjunction with any other
antenna or transmitter.

Warning: This device has been tested with a MMCX connector and antennas as listed in the
table below. When integrated into the OEM products, these fixed antennas require professional
installation preventing end users from replacing them with non-compliant antennas.

List of approved antennas:

      Omni Directional, MT-482016NA, 8.5 dBi
      Panel Antenna, PA58-24-ANT, 24 dBi
      Dish Antenna, HDDA5W-32-DP2, 32 dBi

Antennas of same type and lower gain than those listed above may be used in compliance with
47CFR paragraph 15.212. Additional certification will be required for use other than fixed or
mobile installation.

Antenna Installation warning: It is installer's responsibility to ensure that only those
antennas certified with the product are used for operation in the United States (or where FCC
rules apply). The use of any antenna other than those certified with the product is expressly
forbidden in accordance to FCC rules CFR47 paragraph 15.204.               It is the installers’
responsibility to configure the output power level according to country regulations and antenna
type.



Document Created: 2014-07-03 10:59:48
Document Modified: 2014-07-03 10:59:48

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC