User Manual

FCC ID: TV7GRV-A52HPN

Users Manual

Download: PDF
FCCID_3413562

RouterBOARD  Groove     Quick  Setup  Guide  and  Warranty  Information   The  RouterBOARD  Groove  comes  preinstalled  in  an  outdoor  case,  with  a  built-­‐in  wireless  interface,   an  N-­‐Male  antenna  connector,  and  one  10/100  Ethernet  connector  which  supports  MDI-­‐X  auto   detection.  The  device  is  packaged  with  a  24V  power  adapter,  a  PoE  injector  and  two  mounting  loops.   Several  models  are  available  (dual  band,  single  band,  AP  and  CPE  variants).     First  use   1. Connect  the  antenna  to  the  N-­‐Male  connector   2. Twist  to  open  the  Groove  case,  connect  an  Ethernet  cable  to  the  Ethernet  port   3. Use  the  provided  rubber  insulator  to  put  on  the  Ethernet  cable,  and  push  it  into  the  case   opening,  so  that  the  opening  is  tightly  closed   4. The  Groove  accepts  8-­‐30V  Passive  PoE  from  a  PoE  injector   5. The  default  IP  address  from  Ether1  is  192.168.88.1  for  configuration   Username  is  admin  and  there  is  no  password   6. Depending  on  the  antenna  used,  you  must  set  it’s  gain  in  the  RouterOS  software  to  ensure   that  EIRP  meets  the  limit  set  by  authorities.  This  is  done  in  the  Wireless  menu.     Powering   The  board  accepts  powering  from  the  Ethernet  port  (Passive  PoE):   • Ethernet  port  accepts  passive  Power  over  Ethernet  8-­‐30V  DC.  Package  contains  a  24V   adapter  and  a  PoE  injector.   Maximum  power  consumption  of  the  device  is  4W.   Booting  process   Initial  connection  has  to  be  done  via  the  Ethernet  cable.  Open  192.168.88.1  in  your  web  browser,  and  choose  “Webfig”  for   browser  based  configuration  or  “Winbox”  for  a  Windows  utility  with  the  same  functions.  Username  is  admin  and  there  is  no   password.  In  case  IP  connection  is  not  available,  Winbox  can  be  used  to  connect  to  the  MAC  address  of  the  device.  More   information  here:  http://wiki.mikrotik.com/wiki/First_time_startup   In  case  you  wish  to  boot  the  device  from  network,  for  example  to  use  MikroTik  Netinstall,  hold  the  RESET  button  of  the   device  when  starting  it  until  the  LED  light  turns  off,  and  Metal  will  start  to  look  for  Netinstall  servers.   Mounting   The  Groove  is  to  be  mounted  vertically,  so  that  the  Ethernet  cable  points  downwards.     If  you  wish  to  tighten  the  Groove  to  a  pole,  you  can  do  it  with  the  provided  mounting  loops.  The  Groove  comes  bundled  with   two  mounting  loops  -­‐  guide  the  loops  around  the  Groove  though  the  provided  edge  markings,  and  around  the  pole  where  it   will  be  mounted.  You  should  avoid  connecting  a  loose  Ethernet  cable  to  the  Ethernet  port,  secure  the  cable  to  a  wall  or  the   pole,  so  that  the  cable  weight  is  not  pulling  the  port.  It  is  recommended  to  secure  the  Ethernet  cable  less  than  2m  from  the   Groove  device.  This  is  to  ensure  that  the  cable  doesn't  damage  the  port  by  it's  weight,  or  doesn't  fall  out.       See  www.routerboard.com  for  more  information.  Contact  support@mikrotik.com  for  support  questions.       22-Sep-15

Expansion  Slots  and  Ports   • Built  in  5GHz  or  2GHz  (or  both)  wireless  device  (depends  on  model),  1x1  MIMO   • One  10/100  Ethernet  port,  supporting  automatic  cross/straight  cable  correction  (Auto  MDI/X),  so  you  can  use  either   straight  or  cross-­‐over  cable  for  connecting  to  other  network  devices.  The  Ethernet  port  accepts  8-­‐30V  DC  powering   from  a  passive  PoE  injector.   Buttons  and  Jumpers   • RouterOS  reset  jumper  hole  (no  direct  access,  board  has  removed  from  case)  –  resets  RouterOS  software  to   defaults.  Must  short  circuit  the  metallic  sides  of  the  hole  (with  a  screwdriver,  for  example)  and  boot  the  device.  Hold   screwdriver  in  place  until  RouterOS  configuration  is  cleared.       • RouterBOOT  reset  button  (access  through  the  plastic  door)  has  two  functions:   o Hold  this  button  during  boot  time  until  LED  light  starts  flashing,     release  the  button  to  reset  RouterOS  configuration  (same  result  as  with  reset  hole)   o Hold  this  button  during  boot  time  longer,  until  LED  turns  off,     then  release  it  to  make  the  device  look  for  Netinstall  servers.   Operating  System  Support   Currently  tested  operating  system  is  MikroTik  RouterOS  (starting  from  version  v5.0).   Copyright  and  Trademarks.   Copyright  MikroTikls  SIA.  This  manual  contains  information  protected  by  copyright  law.  No  part  of  it  may  be  reproduced  or   transmitted  in  any  form  without  prior  written  permission  from  the  copyright  holder.  RouterBOARD,  RouterOS,  RouterBOOT   and  MikroTik  are  trademarks  of  MikroTikls  SIA.  All  trademarks  and  registered  trademarks  appearing  in  this  manual  are  the   property  of  their  respective  holders.   Hardware.  MikroTik  warrants  all  RouterBOARD  series  equipment  for  the  term  of  one  year  from  the  shipping  date  to  be  free   of  defects  in  materials  and  workmanship  under  normal  use  and  service,  except  in  case  of  damage  caused  by  mechanical,   electrical  or  other  accidental  or  intended  damages  caused  by  improper  use  or  due  to  wind,  rain,  fire  or  other  acts  of  nature.   To  return  failed  units  to  MikroTik,  you  must  perform  the  following  RMA  (Return  Merchandise  Authorization)  procedure.   Follow  the  instructions  below  to  save  time,  efforts,  avoid  costs,  and  improve  the  speed  of  the  RMA  process.   1. If  you  have  purchased  your  product  from  a  MikroTik  Reseller,  please  contact  the  Reseller  company  regarding  all   warranty  and  repair  issues,  the  following  instructions  apply  ONLY  if  you  purchased  your  equipment  directly  from   MikroTik  in  Latvia.   2. We  do  not  offer  repairs  for  products  that  are  not  covered  by  warranty.  Exceptions  can  be  made  for  RB1000,  RB1100   and  RB1200.   3. Out-­‐of-­‐warranty  devices  and  devices  not  covered  by  warranty  sent  to  Mikrotikls  will  be  returned  to  the  sender  at   sender's  cost.   RMA  Instructions  are  located  on  our  webpage  here:  http://rma.mikrotik.com   Manual.  This  manual  is  provided  “as  is”  without  a  warranty  of  any  kind,  expressed  or  implied,  including,  but  not  limited  to,   the  implied  warranty  of  merchantability  and  fitness  for  a  particular  purpose.  The  manufacturer  has  made  every  effort  to   ensure  the  accuracy  of  the  contents  of  this  manual,  however,  it  is  possible  that  it  may  contain  technical  inaccuracies,   typographical  or  other  errors.  No  liability  is  assumed  for  any  inaccuracy  found  in  this  publication,  nor  for  direct  or  indirect,   incidental,  consequential  or  other  damages  that  may  result  from  such  an  inaccuracy,  including,  but  not  limited  to,  loss  of  data   or  profits.  Please  report  any  inaccuracies  found  to  support@mikrotik.com   See  www.routerboard.com  for  more  information.  Contact  support@mikrotik.com  for  support  questions.       22-Sep-15

Federal Communication Commission Interference Statement (FCC ID: TV7GRV-A52HPN) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT: Exposure to Radio Frequency Radiation. 63 cm minimum distance has to be maintained between the antenna and the occupational user and 152 cm to general public. Under such configuration, the FCC radiation exposure limits set forth for an population/uncotrolled environment can be satisfied. Antenna Installation. WARNING: It is installer's responsibility to ensure that when using the authorized antennas in the United States (or where FCC rules apply); only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country regulations and per antenna type. Professional installation is required of equipment with connectors to ensure compliance with health and safety issues. LIST  OF  APPROVED  2GHz  ANTENNAS:         LIST  OF  APPROVED  5GHz  ANTENNAS:     • 24  dBi  Dish  DC  24-­‐HD-­‐PFIP     • 20  dBi  Panel  WLP-­‐2450-­‐20   • 8.5  dBi  Omni  MTI    Wireless  MT-­‐482016NA   • 17  dBi  Sector  SA  24-­‐90-­‐17-­‐WB     • 24  dBi  Panel  Pacific  Wireless  PA58-­‐24   • 15  dBi  Omni  Directional  (pole)  WL0-­‐2450-­‐15     • 32  dBi  Dish  Pacific  Wireless  HDDA5W-­‐32-­‐DP   • 13  dBi  Omni  Directional  (hor.  Polarization)  HP,  0DH  24-­‐13   See www.routerboard.com for more information. Contact support@mikrotik.com 22-Sep-15

Industry Canada (IC:7442A-GRVA52HPN) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. LE-LAN device restriction: The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux Les utilisateurs devraient aussi être avisés, d’une part, que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) des bandes de 5 250 à 5 350 MHz et de 5 650 à 5 850 MHz et, d’autre part, que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs de RL-EL See www.routerboard.com for more information. Contact support@mikrotik.com 22-Sep-15

CE Declaration of Conformity Full Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/ [EN] English Hereby, MIKROTĪKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. [BG] Bulgarian С настоящето, MIKROTĪKLS SIA декларира, че ROUTERBOARD е в съответствие със съществените изисквания и другитеприложими разпоредби на Директива 1999/5/EC. [CZ] Czech MIKROTĪKLS SIA tímto prohlašuje, že ROUTERBOARD splňuje základní požadavky a všechna příslušná ustanoveni Směrnice 1999/5/ES. [DK] Danish Undertegnede MIKROTĪKLS SIA erklærer herved, at følgende udstyr ROUTERBOARD overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. [DE] German Hiermit erklärt MIKROTĪKLS SIA dass sich das Gerät ROUTERBOARD in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. [EE] Estonian Käesolevaga kinnitab MIKROTĪKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. [GR] Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ MIKROTĪKLS SIA ΔΗΛΩΝΕΙ ΟΤΙ ROUTERBOARD ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ [ES] Spanish Por la presente, MIKROTĪKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva 1999/5/EC. [IT] Italian Con la presente MIKROTĪKLS SIA dichiara che questo ROUTERBOARD è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. [LV] Latvian Ar šo MIKROTĪKLS SIA deklarē, ka ROUTERBOARD atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. [LT] Lithuanian Šiuo MIKROTĪKLS SIA deklaruoja, kad šis ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas [HU] Hungarian A MIKROTĪKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD típusú beren-dezés teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket. [NL] Dutch Hierbij verklaart MIKROTĪKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentiële eisen en de andere relevante bepalin-gen van richtlijn 1999/5/EG. [PL] Polish Niniejszym MIKROTĪKLS SIA deklaruje że ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi właściwymi postanowieniami Dyrektywy 1999/5/EC. [PT] Portuguese Eu, MIKROTĪKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC. [RO] Romanian Prin prezenta, MIKROTĪKLS SIA declară că aparatul ROUTERBOARD este în conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente ale Directivei 1999/5/CE.. [SK] Slovak MIKROTĪKLS SIA týmto vyhlasuje, že ROUTERBOARD spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. [SI] Slovenian MIKROTĪKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive 1999/5/ES. [FI] Finish MIKROTĪKLS SIA vakuuttaa täten että ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. [SE] Swedish Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i direktiv 1999/5/EC. [NO] Norwegian MIKROTĪKLS SIA Erklærer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF. EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More information on http://wiki.mikrotik.comBG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете 192.168.88.1 в уеб браузър, за да настроите продукта. Повече информация в http://wiki.mikrotik.com CZ. Návod k použit: Připojte napájecí adaptér k zapnutí přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete v http://wiki.mikrotik.com DK. Instruktionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.88.1 i en webbrowser til at konfigurere produktet. Mere information i http://wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans http://wiki.mikrotik.com DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öffnen Sie 192.168.88.1 in einem Web- Browser, um das Produkt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com EE. Kasutusjuhend: Ühendage toiteadapter seadme sisselülitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet http://wiki.mikrotik.com ES. Manual de instrucciones: Conecte el adaptador de alimentación para encender la unidad. Abra 192.168.88.1 en un navegador web para configurar el producto. Más información en http://wiki.mikrotik.com IT. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unità. Aprire 192.168.88.1 in un browser Web per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com LV. Lietošanas instrukcija: Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta pārlūku, lai konfigurētu produktu. Plašāka informācija http://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapterį įjunkite įrenginį. Į interneto naršyklę 192.168.88.1 Atidarykite galite konfigūruoti gaminį. Daugiau informacijos rasite http://wiki.mikrotik.com HU. Használati utasítás: Csatlakoztassa a hálózati adaptert a készülék bekapcsolásához. Megnyitása 192.168.88.1 egy webböngészőben beállítani a terméket. Több információ http://wiki.mikrotik.com NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser om het product te configureren. Meer informatie in http://wiki.mikrotik.com PL. Instrukcja obsługi: Podłącz adapter zasilania, aby włączyć urządzenie. Otwórz 192.168.88.1 w przeglądarce internetowej, aby skonfigurować urządzenie. Więcej informacji w http://wiki.mikrotik.com PT. Manual de instruções: Conecte o adaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais informações em http://wiki.mikrotik.com RO. Instrucțiuni de utilizare : Conectaţi adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.88.1 într-un browser web pentru a configura produsul. Mai multe informaţii în http://wiki.mikrotik.com SK. Návod na použitie: Pripojte napájací adaptér k zapnutiu prístroja. Otvorte 192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdete v http://wiki.mikrotik.com SI. Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Več informacij v http://wiki.mikrotik.com FI. Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen. Lisää tietoa http://wiki.mikrotik.com SE. Instruktionsmanual: Anslut nätadaptern för att slå på enheten. Öppna 192.168.88.1 i en webbläsare för att konfigurera produkten. Mer information på http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne 192.168.88.1 i en nettleser for å konfigurere produktet. Mer informasjon på http://wiki.mikrotik.com GR. εγχειρίδιο οδηγιών: Συνδέστε τον προσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.88.1 σε ένα πρόγραμμα περιήγησης στο Web για να διαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο http://wiki.mikrotik.com See www.routerboard.com for more information. Contact support@mikrotik.com for support questions. 22-Sep-15


Document Created: 0780-09-23 00:00:00
Document Modified: 0780-09-23 00:00:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC