Test Report Part 2

FCC ID: TUVGFT-B008

Test Report

Download: PDF
FCCID_3856484

                                                                            Report No.: TCT171225E042

 8DPSK Modulation

      Test channel:                               Lowest channel




                No-hopping mode                                  Hopping mode
Test channel:                                     Highest channel




                No-hopping mode                                    Hopping mode




                                                                                    Page 41 of 62

   Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                                              Report No.: TCT171225E042

6.10. Conducted Spurious Emission Measurement
 6.10.1.         Test Specification

 Test Requirement:                         FCC Part15 C Section 15.247 (d)
 Test Method:                              ANSI C63.10:2013
                                           In any 100 kHz bandwidth outside the intentional
                                           radiation frequency band, the radio frequency power
                                           shall be at least 20 dB below the highest level of the
 Limit:
                                           radiated power. In addition, radiated emissions which fall
                                           in the restricted bands must also comply with the
                                           radiated emission limits.

 Test Setup:

 Test Mode:                                Transmitting mode with modulation
                                           1. The testing follows the guidelines in Spurious RF
                                              Conducted Emissions of ANSI C63.10:2013
                                              Measurement Guidelines
                                           2. The RF output of EUT was connected to the
                                              spectrum analyzer by RF cable and attenuator. The
                                              path loss was compensated to the results for each
                                              measurement.
                                           3. Set to the maximum power setting and enable the
 Test Procedure:                              EUT transmit continuously.
                                           4. Set RBW = 100 kHz, VBW = 300kHz, scan up
                                              through 10th harmonic. All harmonics / spurs must be
                                              at least 20 dB down from the highest emission level
                                              within the authorized band as measured with a 100
                                              kHz RBW.
                                           5. Measure and record the results in the test report.
                                           6. The RF fundamental frequency should be excluded
                                              against the limit line in the operating frequency band.
 Test Result:                              PASS

 6.10.2.        Test Instruments

       Equipment                Manufacturer            Model          Serial Number Calibration Due
  Spectrum Analyzer                  Agilent           N9020A           MY49100060              Sep. 28, 2018
       RF Cable
                                       TCT              RE-06                  N/A              Sep. 27, 2018
    (9KHz-26.5GHz)
  Antenna Connector                    TCT             RFC-01                  N/A              Sep. 27, 2018
 Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to
         international system unit (SI).




                                                                                                        Page 42 of 62

  Hotline: 400-6611-140         Tel: 86-755-27673339        Fax: 86-755-27673332          http://www.tct-lab.com


                                                                           Report No.: TCT171225E042

6.10.3. Test Data

  GFSK mode                            Lowest Channel




                                       Middle Channel




                                       Highest Channel




                                                                                   Page 43 of 62

  Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042
Pi/4DQPSK mode                       Lowest Channel




                                     Middle Channel




                                     Highest Channel




                                                                                 Page 44 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042


8DPSK mode                           Lowest Channel




                                     Middle Channel




                                     Highest Channel




                                                                                 Page 45 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                                      Report No.: TCT171225E042


6.11. Radiated Spurious Emission Measurement
 6.11.1. Test Specification

 Test Requirement:                FCC Part15 C Section 15.209
 Test Method:                     ANSI C63.10:2013
 Frequency Range:                 9 kHz to 25 GHz
 Measurement Distance:            3m
 Antenna Polarization:            Horizontal & Vertical
                                    Frequency       Detector        RBW       VBW            Remark
                                   9kHz- 150kHz    Quasi-peak      200Hz       1kHz      Quasi-peak Value
                                     150kHz-       Quasi-peak       9kHz      30kHz      Quasi-peak Value
 Receiver Setup:                      30MHz
                                   30MHz-1GHz      Quasi-peak     100KHz     300KHz      Quasi-peak Value
                                                     Peak          1MHz       3MHz         Peak Value
                                    Above 1GHz
                                                     Peak          1MHz       10Hz        Average Value

                                                                   Field Strength          Measurement
                                         Frequency
                                                                 (microvolts/meter)      Distance (meters)
                                         0.009-0.490                2400/F(KHz)                 300
                                         0.490-1.705               24000/F(KHz)                 30
                                           1.705-30                      30                      30
                                             30-88                      100                       3
                                            88-216                      150                       3
 Limit:                                    216-960                      200                       3
                                          Above 960                     500                       3

                                                                             Measurement
                                                         Field Strength
                                       Frequency                               Distance         Detector
                                                       (microvolts/meter)
                                                                               (meters)
                                                                 500               3            Average
                                      Above 1GHz
                                                                5000               3             Peak

                                  For radiated emissions below 30MHz




 Test setup:




                                  30MHz to 1GHz




                                                                                              Page 46 of 62

  Hotline: 400-6611-140   Tel: 86-755-27673339     Fax: 86-755-27673332         http://www.tct-lab.com


                                                                         Report No.: TCT171225E042




                                Above 1GHz




Test Mode:                      Transmitting mode with modulation
                                1. The testing follows the guidelines in Spurious
                                    Radiated Emissions of ANSI C63.10:2013
                                    Measurement Guidelines.
                                2. For the radiated emission test below 1GHz:
                                   The EUT was placed on a turntable with 0.8 meter
                                   above ground. The EUT was set 3 meters from the
                                   interference receiving antenna, which was mounted
                                   on the top of a variable height antenna tower. The
                                   EUT was arranged to its worst case and then tune
                                   the antenna tower (from 1 m to 4 m) and turntable
                                   (from 0 degree to 360 degrees) to find the maximum
Test Procedure:                    reading. A pre-amp and a high PASS filter are used
                                   for the test in order to get better signal level.
                                   For the radiated emission test above 1GHz:
                                   Place the measurement antenna on a turntable with
                                   1.5 meter above ground, which is away from each
                                   area of the EUT determined to be a source of
                                   emissions at the specified measurement distance,
                                   while keeping the measurement antenna aimed at
                                   the source of emissions at each frequency of
                                   significant emissions, with polarization oriented for
                                   maximum response. The measurement antenna
                                   may have to be higher or lower than the EUT,

                                                                                 Page 47 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042
                                   depending on the radiation pattern of the emission
                                   and staying aimed at the emission source for
                                   receiving the maximum signal. The final
                                   measurement antenna elevation shall be that which
                                   maximizes the emissions. The measurement
                                   antenna elevation for maximum emissions shall be
                                   restricted to a range of heights of from 1 m to 4 m
                                   above the ground or reference ground plane.
                                3. Set to the maximum power setting and enable the
                                    EUT transmit continuously.
                                4. Use the following spectrum analyzer settings:
                                    (1) Span shall wide enough to fully capture the
                                        emission being measured;
                                    (2) Set RBW=100 kHz for f < 1 GHz, RBW=1MHz
                                        for f>1GHz ; VBW≥RBW;
                                          Sweep = auto; Detector function = peak; Trace
                                          = max hold for peak
                                     (3) For average measurement: use duty cycle
                                         correction factor method per
                                        15.35(c). Duty cycle = On time/100 milliseconds
                                        On time =N1*L1+N2*L2+...+Nn-1*LNn-1+Nn*Ln
                                          Where N1 is number of type 1 pulses, L1 is
                                          length of type 1 pulses, etc.
                                          Average Emission Level = Peak Emission
                                          Level + 20*log(Duty cycle)
                                         Corrected Reading: Antenna Factor + Cable
                                         Loss + Read Level - Preamp Factor = Level
Test results:                   PASS




                                                                                 Page 48 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                                             Report No.: TCT171225E042

6.11.2.        Test Instruments

                                   Radiated Emission Test Site (966)
       Name of                                                                Serial
                                Manufacturer              Model                               Calibration Due
      Equipment                                                              Number
                              ROHDE&SCHW
     Test Receiver                                        ESVD                100008            Sep. 27, 2018
                                  ARZ
                              ROHDE&SCHW
 Spectrum Analyzer                                         FSQ                200061            Sep. 27, 2018
                                  ARZ
                               EM Electronics
     Pre-amplifier              Corporation             EM30265             07032613            Sep. 27, 2018
                                 CO.,LTD
     Pre-amplifier                        HP              8447D           2727A05017            Sep. 27, 2018

    Loop antenna                    ZHINAN             ZN30900A                12024            Sep. 27, 2018

Broadband Antenna               Schwarzbeck            VULB9163                 340             Sep. 27, 2018

    Horn Antenna                Schwarzbeck           BBHA 9120D                631             Sep. 27, 2018

    Horn Antenna                Schwarzbeck             BBH 9170                582             Jun. 07, 2018
    Antenna Mast                     Keleto             CC-A-4M                 N/A                    N/A
      Coax cable
                                          TCT          RE-low-01                N/A             Sep. 27, 2018
     (9KHz-1GHz)
      Coax cable
                                          TCT          RE-high-02               N/A             Sep. 27, 2018
    (9KHz-40GHz)
      Coax cable
                                          TCT          RE-low-03                N/A             Sep. 27, 2018
     (9KHz-1GHz)
      Coax cable
                                          TCT          RE-high-04               N/A             Sep. 27, 2018
    (9KHz-40GHz)

                                    Shurple
  EMI Test Software                                      EZ-EMC                 N/A                    N/A
                                  Technology

Note: The calibration interval of the above test instruments is 12 months and the calibrations are traceable to
        international system unit (SI).




                                                                                                       Page 49 of 62

 Hotline: 400-6611-140         Tel: 86-755-27673339        Fax: 86-755-27673332          http://www.tct-lab.com


                                                                                              Report No.: TCT171225E042

  6.11.3.      Test Data

Duty cycle correction factor for average measurement

  DH5 on time (One Pulse) Plot on Channel 00




 Note:
    1. Worst case Duty cycle = on time/period = 2.86/2.88 = 0.993
    2. Worst case Duty cycle correction factor = 20*log (Duty cycle) = -0.06dB
    3. DH5 has the highest duty cycle worst case and is reported.
    4. The average levels were calculated from the peak level corrected with duty cycle correction factor (-0.06dB)
        derived from 20log (dwell time/100ms). This correction is only for signals that hop with the fundamental signal,
        such as band-edge and harmonic. Other spurious signals that are independent of the hopping signal would not
        use this correction.




                                                                                                        Page 50 of 62

  Hotline: 400-6611-140        Tel: 86-755-27673339         Fax: 86-755-27673332          http://www.tct-lab.com


                                                                             Report No.: TCT171225E042

Please refer to following diagram for individual
                                              Below 1GHz
Horizontal:




                                                                                     Page 51 of 62

   Hotline: 400-6611-140    Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                                           Report No.: TCT171225E042


Vertical:




Note: 1.The low frequency, which started from 9KHz~30MHz, was pre-scanned and the result which was 20dB lower than
        the limit line per 15.31(o) was not reported

       2. Measurements were conducted in all three channels (high, middle, low) and three modulation (GFSK,
          Pi/4 DQPSK, 8DPSK) and the worst case Mode (Lowest channel and 8DPSK) was submitted only.




                                                                                                    Page 52 of 62

   Hotline: 400-6611-140        Tel: 86-755-27673339      Fax: 86-755-27673332         http://www.tct-lab.com


                                                                                              Report No.: TCT171225E042


                                                    Above 1GHz
     Modulation Type: 8DPSK
     Low channel: 2402 MHz
                          Peak           AV    Correction Emission Level
     Frequency Ant. Pol. reading       reading  Factor                   Peak limit AV limit Margin
       (MHz)      H/V                                     Peak      AV
                         (dBµV)        (dBuV)   (dB/m) (dBµV/m) (dBµV/m) (dBµV/m) (dBµV/m)     (dB)
        2390       H      46.25          ---     -8.27    37.98     ---     74        54     -16.02
        4804       H      49.54          ---     0.66     50.20     ---     74        54      -3.80
        7206       H      39.31          ---      9.5     48.81      ---    74        54      -5.19
         ---       H       ---           ---       ---     ---      ---     ---       ---       ---

       2390         V        43.95        ---      -8.27       35.68        ---        74         54        -18.32
       4804         V        48.42        ---       0.66       49.08        ---        74         54         -4.92
       7206         V        37.89        ---        9.5       47.39        ---        74         54         -6.61
        ---         V         ---         ---        ---        ---         ---        ---        ---          ---

     Middle channel: 2441 MHz
                           Peak          AV    Correction Emission Level
     Frequency Ant. Pol. reading       reading  Factor                   Peak limit AV limit Margin
       (MHz)      H/V                                     Peak      AV
                          (dBµV)       (dBµV)   (dB/m) (dBµV/m) (dBµV/m) (dBµV/m) (dBµV/m)     (dB)
        4882       H       41.58         ---     0.99     42.57     ---     74        54     -11.43
        7323       H       38.76         ---     9.87     48.63     ---     74        54      -5.37
         ---       H        ---          ---       ---     ---      ----    ---       ---       ---

       4882         V        42.72        ---       0.99       43.71        ---        74         54        -10.29
       7323         V        39.31        ---       9.87       49.18        ---        74         54         -4.82
        ---         V         ---         ---        ---        ---        ----        ---        ---          ---

     High channel: 2480 MHz
                          Peak           AV    Correction Emission Level
     Frequency Ant. Pol. reading       reading  Factor                   Peak limit AV limit Margin
       (MHz)       H/V                                    Peak      AV
                         (dBµV)        (dBµV)   (dB/m) (dBµV/m) (dBµV/m) (dBµV/m) (dBµV/m)     (dB)
       2483.5       H     45.63          ---     -7.83    37.80     ---     74        54     -16.20
        4960        H     48.91          ---     1.33     50.24     ---     74        54      -3.76
        7440        H     38.72          ---     10.22    48.94     ---     74        54      -5.06
         ---        H       ---          ---       ---     ---      ---     ---       ---       ---

   2483.5           V        48.01        ---      -7.83       40.18        ---        74         54        -13.82
    4960            V        49.13        ---       1.33       50.46        ---        74         54         -3.54
    7440            V        38.34        ---      10.22       48.56        ---        74         54         -5.44
      ---           V         ---         ---        ---        ---         ---        ---        ---          ---
Note:
1.    Emission Level=Peak Reading + Correction Factor; Correction Factor= Antenna Factor + Cable loss – Pre-amplifier
2.    Margin (dB) = Emission Level (Peak) (dBµV/m)-Average limit (dBµV/m)
3.    The emission levels of other frequencies are very lower than the limit and not show in test report.
4.    Measurements were conducted from 1 GHz to the 10th harmonic of highest fundamental frequency.
5.    Data of measurement shown “---“in the above table mean that the reading of emissions is attenuated more than 20 dB
      below the limits or the field strength is too small to be measured.
6.    Measurements were conducted in all three modulation (GFSK, Pi/4 DQPSK, 8DPSK), and the worst case Mode
      (8DPSK) was submitted only.




                                                                                                        Page 53 of 62

     Hotline: 400-6611-140       Tel: 86-755-27673339        Fax: 86-755-27673332         http://www.tct-lab.com


                                                                         Report No.: TCT171225E042


                   Appendix A: Photographs of Test Setup
                               Product: Bluetooth Speaker
                                   Model: GFT-B008
                                   Radiated Emission




                                                                                 Page 54 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                          Report No.: TCT171225E042


                                               CE




                                                                                  Page 55 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339    Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042


                        Appendix B: Photographs of EUT
                              Product: Bluetooth Speaker
                                  Model: GFT-B008
                                   External Photos




                                                                                 Page 56 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042




                                                                                 Page 57 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042




                                                                                 Page 58 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042




                                                                                 Page 59 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042


                              Product: Bluetooth Speaker
                                  Model: GFT-B008
                                   Internal Photos




                                                                                 Page 60 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042




                                                                                 Page 61 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com


                                                                         Report No.: TCT171225E042




                            *****END OF REPORT*****




                                                                                 Page 62 of 62

Hotline: 400-6611-140   Tel: 86-755-27673339   Fax: 86-755-27673332   http://www.tct-lab.com



Document Created: 2018-05-17 17:37:24
Document Modified: 2018-05-17 17:37:24

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC