Users Manual

FCC ID: TUV2406

Users Manual

Download: PDF

FCCID_1533741

Wireless Optical Mouse User Manual

Feature
1． 2.4G frequency，digital cordless with distance up to 5-7meters
2． Internal 65，000 group ID code，plug and play
3． 1000/1500/2000DPI, high-precision and high- stabilization
4． low power consumption，automatic sleeping function.
Compatible
IBM PC and compatibles，Win98SE/Me/2000/XP/VISTA /Win7 operating system，no need
driver
Installation
1， Take the receiver from the packing，plug onto the USB port of PC or BOTEBOOK’，after a
few minutes，the software of receiver will be installed automatically. If it is Win98SE system，
you need to follow the prompting frame to finish the installation.
2， Open the battery cover，put into 1 AA size battery（Pay attention to the battery polarity）
3， Indicator light will flash for a few seconds
4， You can use it till you can find the curser on the PC screen
Reset
Wireless mouse’s remitter and receiver has storage the same group ID code，It will make sure
the mouse remit and receive the corresponding data. If any of ID code for each group disappear
or disaffinity, the mouse will not work，and you need to reset it.
1， Insert the receiver on the USB port, the indicator light will flicker，then put battery into
mouse，turn on the mouse.
2， When the indicator light flickers，press the right key of emitter，then press the middle key
for three seconds, emitter will emit corresponding code，then the connection finished.
3， Move the mouse and you will find the curser on the PC screen.
Note：Don’t always press the ID switch，unless the ID code will be reset and you need to
reconnect the mouse.
CPI
1000/1500/2000CPI can shift be adjusted, the DPI will change if you press the switching on the
top of the mouse.
Tips
1. The work distance is about 5-7 meters, but it will be less if there is
any barrier.
2. This mouse uses laser light as transfer checking, it comply with
correlative safe standards, please do not look into the bottom of the mouse
directly.
3. It has automatic sleeping function, the mouse will sleep if you don’t use it for about 10
minutes, just press any key to rouse it.
4. Take off the battery if you don’t use the mouse for a long time.
5. Change the battery in time please.
6. Automatic ID code memory function，just reconnect it if the ID code reset.
7. You can store the receiver in the emitter’s abdomen storage compartment if you don’t
use it.

FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Remark
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules.. This limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates radio frequency, if
not installed and used according to the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measure.
* Reorient or relocate the receiving antenna
* In rease the separation between the equipment and receiver
c

* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
* Consult with the dealer or an experienced radio/TV technician for help

Document Created: 2011-08-08 17:49:52
Document Modified: 2011-08-08 17:49:52

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC