Test Report

FCC ID: TQ4MEDIOL40

Test Report

Download: PDF
FCCID_4106709

Access to the World FCC 47 CFR PART 15 SUBPART C CERTIFICATION TEST REPORT For Reader MODEL No.: Medio L40 FCC ID: TQ4MEDIOL40 Trademark: REPORT NO.: ES181122027W ISSUE DATE: December 11, 2018 Prepared for Invengo Information Technology co.,Ltd. 27th and 28th Floor,Hi-Tech Zone Union Tower, NO.63, Gaoxin South 10th Road, Yuehai Sub-district, Nanshan District, Shenzhen,China Prepared by EMTEK(SHENZHEN) CO., LTD. Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 TRF No.:FCC 15.225/A Page 1 of 31 Report No.: ES181122027W Ver.1.0

Access to the World Table of Contents 1 EUT TECHNICAL DESCRIPTION .................................................................................................................... 4 2 SUMMARY OF TEST RESULT ........................................................................................................................... 5 3 TEST METHODOLOGY ...................................................................................................................................... 6 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................................... 6 3.2 MEASUREMENT EQUIPMENT USED ..................................................................................................... 6 3.3 DESCRIPTION OF TEST MODES ............................................................................................................. 7 4 FACILITIES AND ACCREDITATIONS ............................................................................................................. 8 4.1 FACILITIES ................................................................................................................................................. 8 4.2 LABORATORY ACCREDITATIONS AND LISTINGS.............................................................................. 8 5 TEST SYSTEM UNCERTAINTY ........................................................................................................................ 9 6 SETUP OF EQUIPMENT UNDER TEST ......................................................................................................... 10 6.1 RADIO FREQUENCY TEST SETUP 1 ..................................................................................................... 10 6.2 RADIO FREQUENCY TEST SETUP 2 ..................................................................................................... 10 6.3 CONDUCTED EMISSION TEST SETUP..................................................................................................11 6.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ................................................................. 12 6.5 SUPPORT EQUIPMENT ........................................................................................................................... 12 7 TEST REQUIREMENTS .................................................................................................................................... 13 7.1 OCCUPIED BANDWIDTH....................................................................................................................... 13 7.2 FREQUENCY STABILITY ....................................................................................................................... 15 7.3 RADIATED SPURIOUS EMISSION ........................................................................................................ 17 7.4 CONDUCTED EMISSION TEST ............................................................................................................. 28 8 ANTENNA APPLICATION ................................................................................................................................ 31 8.2 RESULT ....................................................................................................................................................... 31 TRF No.:FCC 15.225/A Page 2 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TEST RESULT CERTIFICATION Applicant : Invengo Information Technology co.,Ltd. 27th and 28th Floor,Hi-Tech Zone Union Tower, NO.63, Gaoxin South 10th Road, Address： Yuehai Sub-district, Nanshan District, Shenzhen,China Manufacturer : Invengo Information Technology co.,Ltd. 27th and 28th Floor,Hi-Tech Zone Union Tower, NO.63, Gaoxin South 10th Road, Address： Yuehai Sub-district, Nanshan District, Shenzhen,China EUT : Reader Model Name : Medio L40 Trademark : Measurement Procedure Used: APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 2, Subpart J PASS FCC 47 CFR Part 15, Subpart C The above equipment was tested by EMTEK(SHENZHEN) CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.225. The test results of this report relate only to the tested sample identified in this report. Date of Test : November 23,2018 to December 7, 2018 Prepared by : Sewen Guo /Editor Reviewer : Joe Xia /Supervisor Approve & Authorized Signer : Lisa Wang/Manager TRF No.:FCC 15.225/A Page 3 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 1 EUT TECHNICAL DESCRIPTION Characteristics Description Device Type: RFID Modulation: ASK modulation Operating Frequency 13.553-13.567MHz Range(s): Channel Frequency: 13.56MHz Number of Channels: 1 channel Antenna Type : Coil Antenna DC24V by Adapter Adapter supply: Power supply: Model：VEH40US24 MAX power output:40W Input：100-240V,47-63Hz,0.93A Output：24.0V,1.66A MAX Temperature Range 0°C ~ +50°C Note: for more details, please refer to the User’s manual of the EUT. TRF No.:FCC 15.225/A Page 4 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 2 SUMMARY OF TEST RESULT FCC Part Clause Test Parameter Verdict Remark 2.1049 Occupied Bandwidth PASS 15.225(e) Frequency stability PASS 15.225(d) Radiated Spurious Emissions PASS 15.209 15.207 Conducted Emission PASS NOTE1: N/A (Not Applicable) RELATED SUBMITTAL(S) / GRANT(S): This submittal(s) (test report) is intended for FCC ID: TQ4MEDIOL40 filing to comply with Section 15.225 of the FCC Part 15, Subpart C Rules. TRF No.:FCC 15.225/A Page 5 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 3 TEST METHODOLOGY 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS According to its specifications, the EUT must comply with the requirements of the following standards: FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart C 3.2 MEASUREMENT EQUIPMENT USED 3.2.1 Conducted Emission Test Equipment EQUIPMENT MFR MODEL SERIAL LAST CAL. Due. CAL TYPE NUMBER NUMBER Test Receiver Rohde & Schwarz ESCS30 828985/018 05/28/2018 05/28/2019 L.I.S.N. Schwarzbeck NNLK8129 8129203 05/28/2018 05/28/2019 50Ω Coaxial Switch Anritsu MP59B M20531 N/A N/A 3.2.2 Radiated Emission Test Equipment EQUIPMENT MFR MODEL SERIAL LAST CAL. Due. CAL TYPE NUMBER NUMBER EMI Test Receiver Rohde & Schwarz ESU 1302.6005.26 05/28/2018 05/28/2019 Pre-Amplifier HP 8447D 2944A07999 05/28/2018 05/28/2019 Bilog Antenna Schwarzbeck VULB9163 142 05/28/2018 05/28/2019 Loop Antenna ARA PLA-1030/B 1029 05/28/2018 05/28/2019 Cable Schwarzbeck AK9513 ACRX1 05/28/2018 05/28/2019 Cable Rosenberger N/A FP2RX2 05/28/2018 05/28/2019 Cable Schwarzbeck AK9513 CRPX1 05/28/2018 05/28/2019 Cable Schwarzbeck AK9513 CRRX2 05/28/2018 05/28/2019 3.2.3 Radio Frequency Test Equipment EQUIPMENT MFR MODEL SERIAL LAST CAL. Due. CAL TYPE NUMBER NUMBER Spectrum Analyzer Agilent E4407B 88156318 05/28/2018 05/28/2019 Signal Analyzer Agilent N9010A My53470879 05/28/2018 05/28/2019 Power meter Anritsu ML2495A 0824006 05/28/2018 05/28/2019 Power sensor Anritsu MA2411B 0738172 05/28/2018 05/28/2019 Remark: Each piece of equipment is scheduled for calibration once a year. TRF No.:FCC 15.225/A Page 6 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 3.3 DESCRIPTION OF TEST MODES The EUT has been tested under its typical operating condition. The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. The Transmitter was operated in the normal operating mode. The TX frequency was fixed which was for the purpose of the measurements. Pre-defined engineering program for regulatory testing used to control the EUT for staying in continuous transmitting mode is programmed. TRF No.:FCC 15.225/A Page 7 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 4 FACILITIES AND ACCREDITATIONS 4.1 FACILITIES All measurement facilities used to collect the measurement data are located at Bldg 69, Majialong Industry Zone District, Nanshan District, Shenzhen, China The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.10 and CISPR Publication 22. 4.2 LABORATORY ACCREDITATIONS AND LISTINGS Site Description EMC Lab. : Accredited by CNAS,2016.10.24 The certificate is valid until 2022.10.28 The Laboratory has been assessed and proved to be in compliance with CNAS-CL01:2006 (identical to ISO/IEC 17025:2005) The Certificate Registration Number is L2291. Accredited by TUV Rheinland Shenzhen 2016.5.19 The Laboratory has been assessed according to the requirements ISO/IEC 17025. Accredited by FCC, August 06, 2018 Designation Number: CN1204 Test Firm Registration Number: 882943 Accredited by A2LA, August 31, 2020 The Certificate Registration Number is 4321.01. Accredited by Industry Canada, November 09, 2018 The Conformity Assessment Body Identifier is CN0008 Name of Firm : EMTEK(SHENZHEN) CO., LTD. Site Location : Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TRF No.:FCC 15.225/A Page 8 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 5 TEST SYSTEM UNCERTAINTY The following measurement uncertainty levels have been estimated for tests performed on the apparatus: Parameter Uncertainty Radio Frequency ±1x10^-5 Conducted Emissions Test ±2.0dB Radiated Emission Test ±2.0dB Occupied Bandwidth Test ±1.0dB All emission, radiated ±3dB Temperature ±0.5℃ Humidity ±3% Measurement Uncertainty for a level of Confidence of 95% TRF No.:FCC 15.225/A Page 9 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 6 SETUP OF EQUIPMENT UNDER TEST 6.1 RADIO FREQUENCY TEST SETUP 1 The component’s antenna ports(s) of the EUT are connected to the measurement instrument per an appropriate attenuator. The EUT is controlled by PC/software to emit the specified signals for the purpose of measurements. Measurement EUT Attenuator Instrument 6.2 RADIO FREQUENCY TEST SETUP 2 The test site semi-anechoic chamber has met the requirement of NSA tolerance 4 dB according to the standards: ANSI C63.10. The test distance is 3m.The setup is according to the requirements in Section 13.1.4.1 of ANSI C63.10-2013 and CAN/CSA-CEI/IEC CISPR 22. Below 30MHz： The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna (loop antenna). The Antenna should be positioned with its plane vertical at the specified distance from the EUT and rotated about its vertical axis for maximum response at each azimuth about the EUT. The center of the loop shall be 1 m above the ground. For certain applications, the loop antenna plane may also need to be positioned horizontally at the specified distance from the EUT. Above 30MHz： The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). (a) Radiated Emission Test Set-Up, Frequency Below 30MHz Turntable 3m EUT Test 0.8 m Receiver Ground Plane Coaxial Cable TRF No.:FCC 15.225/A Page 10 of 31 Report No.: ES181122027W Ver.1.0

Access to the World (b) Radiated Emission Test Set-Up, Frequency Below 1000MHz 3m Turntable 1m to 4m EUT Test 0.8m Receiver Ground Plane Coaxial Cable 6.3 CONDUCTED EMISSION TEST SETUP The mains cable of the EUT (maybe per AC/DC Adapter) must be connected to LISN. The LISN shall be placed 0.8 m from the boundary of EUT and bonded to a ground reference plane for LISN mounted on top of the ground reference plane. This distance is between the closest points of the LISN and the EUT. All other units of the EUT and associated equipment shall be at least 0.8m from the LISN. Ground connections, where required for safety purposes, shall be connected to the reference ground point of the LISN and, where not otherwise provided or specified by the manufacturer, shall be of same length as the mains cable and run parallel to the mains connection at a separation distance of not more than 0.1 m. According to the requirements in ANSI C63.10-2013 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30 MHz using CISPR Quasi-Peak and average detector mode. Reference Ground Reference EUT Auxiliary Ground EMI Receiver Equipment 50Ω 80cm 80cm LISN LISN TRF No.:FCC 15.225/A Page 11 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 6.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM EUT Ac Adapter Ac Source 6.5 SUPPORT EQUIPMENT EUT Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite DC cable 1.2 Unshielded With Ferrite antenna cable 3.0 Shielded With Ferrite Auxiliary Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite AC cable 1.2 Unshielded Without Ferrite Auxiliary Equipment List and Details Description Manufacturer Model Serial Number Notebook Lenovo WB0205140E WB06355728 Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 3. Unless otherwise denoted as EUT in『Remark』column , device(s) used in tested system is a support equipment TRF No.:FCC 15.225/A Page 12 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 7 TEST REQUIREMENTS 7.1 OCCUPIED BANDWIDTH 7.1.1 Applicable Standard According to FCC Part 2.1049 7.1.2 Conformance Limit No limit requirement. 7.1.3 Test Configuration Test according to clause 6.1 radio frequency test setup 1 7.1.4 Test Procedure The EUT was operating in transmit mode and controlled its channel. Printed out the test result from the spectrum by hard copy function. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator. The path loss was compensated to the results for each measurement. Set to the maximum power setting and enable the EUT transmit continuously Set RBW = 1% occupied bandwidth (30Hz). Set the video bandwidth (VBW) =3 times RBW . Set Span= approximately 2 to 3 times the occupied bandwidth Set Detector = Peak. Set Trace mode = max hold. Set Sweep = auto couple. The EUT should be transmitting at its maximum data rate. Allow the trace to stabilize. Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 99% down one side of the emission. Reset the markerdelta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 99% bandwidth of the emission. If this value varies with different modes of operation (e.g., data rate, modulation format, etc.), repeat this test for each variation. Measure and record the results in the test report. 7.1.5 Test Results Temperature : 25℃ Test Date : Humidity : 65 % Test By: Andy Modulation Channel Channel Frequency Measurement Bandwidth Limit Verdict Mode Number (MHz) (kHz) (kHz) ASK 0 13.56 49.34 N/A PASS Note: N/A (Not Applicable) TRF No.:FCC 15.225/A Page 13 of 31 Report No.: ES181122027W Ver.1.0

Access to the World Occupied Bandwidth Test Model Channel 0: 13.56MHz ASK Modulation TRF No.:FCC 15.225/A Page 14 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 7.2 FREQUENCY STABILITY 7.2.1 Applicable Standard According to FCC Part 2.1055 7.2.2 Conformance Limit According to part 15.225(e),The frequency tolerance of the carrier signal shall be maintained within ±0.01% of the operating frequency over a temperature variation of −20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. 7.2.3 Test Configuration Test according to clause 6.1 radio frequency test setup 7.2.4 Test Procedures Connect the EUT to frequency analyzer via the antenna connector. EUT was placed at temperature chamber and connected to an external power supply. Temperature and voltage condition shall be tested to confirm frequency stability. (a) Frequency measurements shall be made at the extremes of the specified temperature range and at o intervals of not more than 10 centigrade through the range. A period of time sufficient to stabilize all of the components of the oscillator circuit at each temperature level shall be allowed prior to frequency measurement. The short-term transient effects on the frequency of the transmitter due to keying (except for broadcast transmitters) and any heating element cycling normally occurring at each ambient temperature level also shall be shown. Only the portion or portions of the transmitter containing the frequency determining and stabilizing circuitry need be subjected to the temperature variation test. (b) The frequency stability shall be measured with variation of primary supply voltage as follows: (1) Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment. (2) For hand carried, battery powered equipment, reduce primary supply voltage to the battery operating end point, which shall be specified by the manufacturer. 7.2.5 Test Results TRF No.:FCC 15.225/A Page 15 of 31 Report No.: ES181122027W Ver.1.0

Access to the World Test Condition Channel Operation Channel Freq.Dev. Deviation Limit Temp Frequency Mode Number Voltage (Hz) (ppm) (ppm) (MHz) (V) (℃) -20 13.559957 -43 -3.17 10 -10 13.559984 -16 -1.18 10 0 13.559923 -77 -5.68 10 10 13.55998 -20 -1.47 10 Vnom 20 13.559932 -68 -5.01 10 30 13.559996 -4 -0.29 10 ASK CH0 40 13.559936 -64 -4.72 10 50 13.559923 -77 -5.68 10 85% 20 13.559972 -28 -2.06 10 Vnom 115% 20 13.559946 -54 -3.98 10 Vnom VERDICT PASS TRF No.:FCC 15.225/A Page 16 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 7.3 RADIATED SPURIOUS EMISSION 7.3.1 Applicable Standard According to FCC Part 15.225 and 15.209 7.3.2 Conformance Limit Field Strength of Fundamental Emissions and Spectrum Mask Emissions (uV/m)@30m (dBuV/m)@30m (dBuV/m)@10m (dBuV/m)@3m (dBuV/m)@1m Fundamental 15848 84.0 103.1 124.0 143.1 Quasi peak measurement of the fundamental. Spectrum Mask Freq. of (uV/m)@30m (dBuV/m)@30m (dBuV/m)@10m (dBuV/m)@3m (dBuV/m)@1m Emission (MHz) 1.705~13.110 30 29.5 48.6 69.5 88.6 13.110~13.410 106 40.5 59.6 80.5 99.6 13.410~13.553 334 50.5 69.6 90.5 109.6 13.553~13.567 15848 84.0 103.1 124.0 143.1 13.567~13.710 334 50.5 69.6 90.5 109.6 13.710~14.010 106 40.5 59.6 80.5 99.6 14.010~30.000 30 29.5 48.6 69.5 88.6 According to FCC Part15.205, Restricted bands MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 10.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.17725-4.17775 37.5-38.25 1435-1626.5 9.0-9.2 4.20725-4.20775 73-74.6 1645.5-1646.5 9.3-9.5 6.215-6.218 74.8-75.2 1660-1710 10.6-12.7 6.26775-6.26825 123-138 2200-2300 14.47-14.5 8.291-8.294 149.9-150.05 2310-2390 15.35-16.2 8.362-8.366 156.52475-156.52525 2483.5-2500 17.7-21.4 8.37625-8.38675 156.7-156.9 2690-2900 22.01-23.12 8.41425-8.41475 162.0125-167.17 3260-3267 23.6-24.0 12.29-12.293 167.72-173.2 3332-3339 31.2-31.8 12.51975-12.52025 240-285 3345.8-3358 36.43-36.5 12.57675-12.57725 322-335.4 3600-4400 (2) 13.36-13.41 According to FCC Part15.205, the level of any transmitter spurious emission in Restricted bands shall not exceed the level of the emission specified in the following table Restricted Frequency(MHz) Field Strength (μV/m) Field Strength (dBμV/m) Measurement Distance 0.009-0.490 2400/F(KHz) 48.5 - 13.8 300 0.490-1.705 24000/F(KHz) 33.8 – 23.0 30 1.705-30 30 29.5 30 30-88 100 40.0 3 88-216 150 43.5 3 216-960 200 46.0 3 Above 960 500 54.0 3 TRF No.:FCC 15.225/A Page 17 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 7.3.3 Test Configuration Test according to clause 6.2 radio frequency test setup 2 7.3.4 Test Procedure This test is required for any spurious emission that falls in a Restricted Band, as defined in Section 15.205. It must be performed with the highest gain of each type of antenna proposed for use with the EUT. Use the following spectrum analyzer settings: The EUT was placed on a turn table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Span = wide enough to fully capture the emission being measured RBW = 100 kHz for f < 1 GHz(30MHz to 1GHz), 200Hz for f<150KHz(9KHz to 150KHz), 9KHz for f<30MHz(150KHz to 30KHz) VBW ≥ RBW Sweep = auto Detector function = peak Trace = max hold Follow the guidelines in ANSI C63.10-2013 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization, etc. A pre-amp and a high pass filter are required for this test, in order to provide the measuring system with sufficient sensitivity. Allow the trace to stabilize. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre-amp gain, etc., is the peak field strength, which must comply with the limit specified in Section 15.35(b). Submit this data. Now set the VBW to 10 Hz, while maintaining all of the other instrument settings. This peak level, once corrected, must comply with the limit specified in Section 15.209. If the dwell time per channel of the hopping signal is less than 100 ms, then the reading obtained with the 10 Hz VBW may be further adjusted by a “duty cycle correction factor”, derived from 20log(dwell time/100 ms), in an effort to demonstrate compliance with the 15.209 limit. Submit this data. Repeat above procedures until all frequency measured was complete. 7.3.5 Test Results TRF No.:FCC 15.225/A Page 18 of 31 Report No.: ES181122027W Ver.1.0

Access to the World  Field Strength of Fundamental Emissions and Spectrum Mask TRF No.:FCC 15.225/A Page 19 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 20 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 21 of 31 Report No.: ES181122027W Ver.1.0

Access to the World  Spurious Emission below 150kHz (9KHz to 150kHz) Temperature: 24℃ Test Date: Humidity: 53 % Test By: KK Test mode: TX Mode Emission Freq. Ant.Pol. Limit 3m(dBuV/m) Over(dB) Level(dBuV/m) (MHz) H/V PK AV PK AV PK AV -- -- -- -- -- -- -- -- Note: the amplitude of spurious emission that is attenuated by more than 20dB below the permissible limit has no need to be reported. Distance extrapolation factor =40log(Specific distance/ test distance)( dB); Limit line=Specific limits(dBuV) + distance extrapolation factor TRF No.:FCC 15.225/A Page 22 of 31 Report No.: ES181122027W Ver.1.0

Access to the World  Spurious Emission below 30MHz (150KHz to 30MHz) All mode have been tested, and the worst result was report as below: TRF No.:FCC 15.225/A Page 23 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 24 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 25 of 31 Report No.: ES181122027W Ver.1.0

Access to the World  Spurious Emission Above 30MHz (30MHz to 1GHz) TRF No.:FCC 15.225/A Page 26 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 27 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 7.4 CONDUCTED EMISSION TEST 7.4.1 Applicable Standard According to FCC Part 15.207(a) 7.4.2 Conformance Limit Conducted Emission Limit Frequency(MHz) Quasi-peak Average 0.15-0.5 66-56 56-46 0.5-5.0 56 46 5.0-30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 7.4.3 Test Configuration Test according to clause 7.3 conducted emission test setup 7.4.4 Test Procedure The EUT was placed on a table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Repeat above procedures until all frequency measured were complete. 7.4.5 Test Results Pass The 120V &240V voltagehave been tested, and the worst result recorded was report as below: TRF No.:FCC 15.225/A Page 28 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 29 of 31 Report No.: ES181122027W Ver.1.0

Access to the World TRF No.:FCC 15.225/A Page 30 of 31 Report No.: ES181122027W Ver.1.0

Access to the World 8 ANTENNA APPLICATION 8.1.1 Antenna Requirement Standard Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier FCC CRF Part 15.203 current devices or to devices operated under the provisions of §15.211, §15.213, §15.217, §15.219, or §15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with §15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this part are not exceeded. For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 8.2 RESULT The EUT’S antenna is coil antenna, The antenna’s gain is 0dBi and meets the requirement. and the antenna can’t be replaced by the user, which in accordance to section 15.203. TRF No.:FCC 15.225/A Page 31 of 31 Report No.: ES181122027W Ver.1.0


Document Created: 2018-12-13 11:42:31
Document Modified: 2018-12-13 11:42:31
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC