FCC Part 15.225 Test Report

FCC ID: TMEWR5000X012

Test Report

Download: PDF
FCCID_3728912

Test Report Prepared for: Blackboard, Inc. Model: WR5000 Description: Security Access systems and as an attendance wall reader Serial Number: N/A FCC ID: TMEWR5000X012 IC: 8327A-WR5000X012 To FCC Part 15.225 Date of Issue: January 19, 2018 On the behalf of the applicant: Blackboard, Inc. 22601 N 19th Ave Suite 130 Phoenix, AZ 85027 Attention of: Tim Mattson, Hardware Engineer Ph: (623)476-1141 E-Mail: Tim.Mattson@blackboard.com Prepared by Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1770014 Alex Macon Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing. All results contained herein relate only to the sample tested p1770014_FCC_Part 15.225_Rev 3.0 Page 1 of 14

Test Report Revision History Revision Date Revised By Reason for Revision 1.0 October 9, 2017 Alex Macon Original Document Updated table on page 8 Added measured frequency to page 9 2.0 January 18, 2018 Alex Macon Updated C63.10 version on page 6 Clarified test procedure on page 10 Included additional statement in the 3.0 January 19, 2018 Alex Macon field strength test procedure p1770014_FCC_Part 15.225_Rev 3.0 Page 2 of 14

Table of Contents Description Page Standard Test Conditions Engineering Practices ............................................................................... 6 Test Results Summary ........................................................................................................................ 7 Field Strength ...................................................................................................................................... 8 Frequency Stability .............................................................................................................................. 9 Radiated Emissions........................................................................................................................... 10 Powerline Conducted Emissions ....................................................................................................... 11 99% Occupied Bandwidth ................................................................................................................. 13 Test Equipment Utilized .................................................................................................................... 14 p1770014_FCC_Part 15.225_Rev 3.0 Page 3 of 14

ILAC / A2LA Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to the joint ISO-ILAC-IAF Communiqué dated January 2009). The tests results contained within this test report all fall within our scope of accreditation, unless noted in the table below. Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. Testing Certificate Number: 2152.01 FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A p1770014_FCC_Part 15.225_Rev 3.0 Page 4 of 14

The applicant has been cautioned as to the following: 15.21 Information to User The user’s manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 15.27(a) Special Accessories Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator the responsible part may employ other methods of ensuring that the special accessories are provided to the consumer, without an additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. p1770014_FCC_Part 15.225_Rev 3.0 Page 5 of 14

Standard Test Conditions Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI C63.10-2013 and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104°F), unless the particular equipment requirements specified testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Measurement results, unless otherwise noted, are worst-case measurements. Environmental Conditions Temperature Humidity Pressure (°C) (%) (mbar) 23.2 – 24.8 31 - 36 966 - 969 EUT Description Model: WR5000 Description: Security Access systems and as an attendance wall reader Firmware: N/A Software: N/A Serial Number: N/A Additional Information: The device incorporated and NFC transmitter at 13.56MHz and a pre-certified 2.4GHz module. EUT Operation during Tests The device was placed in continuous transmit tone during all testing. Accessories: None Cables: None Modifications: None p1770014_FCC_Part 15.225_Rev 3.0 Page 6 of 14

Test Results Summary Pass, Specification Test Name Comments Fail, N/A 15.225(a) Fundamental Field Strength Pass 15.225(b)(c)(d) Out of Band Spurious Emissions Pass 15.225(e) Frequency Stability Pass 12.209 Radiated Emissions Pass 12.207 Conducted Powerline Emissions Pass RSS-210 99% Occupied Bandwidth Pass 15.203: Antenna Requirement: X The antenna is permanently attached to the EUT The antenna uses a unique coupling The EUT must be professionally installed The antenna requirement does not apply p1770014_FCC_Part 15.225_Rev 3.0 Page 7 of 14

Field Strength Engineer: Alex Macon Test Date: 9/12/17 Test Procedure The EUT was tested in an anechoic chamber at a distance of 1 meter from the receiving loop antenna and characterized to the 30 meter limit(40log (1m/30m) A spectrum analyzer was used to verify that the EUT met the requirements for Fundamental Field Strength. The antenna correction and distance correction factors were summed with the quasi-peak measurement to ensure accurate readings were obtained. The following table indicates the highest emission in each of the indicated bands. Measurements were made with an amplified loop antenna and converted to field strength. Test Setup Spectrum EUT Antenna Analyzer Field Strength Frequency Measured Monitored Corrected Distance CF Antenna CF Limit Band Frequency Level Measurement Result (dB) (dB) (dBuV/m) (MHz) (MHz) (dBuV/m) (dBuV/m) 13.110_13.410 13.347 62.95 59.1 17.8 21.65 40.51 Pass 13.410_13.553 13.553 73.94 59.1 17.8 32.64 50.47 Pass 13.553_13.567 13.5593 78.13 59.1 17.8 36.83 84.00 Pass 13.567_13.710 13.567 70.76 59.1 17.8 29.46 50.47 Pass 13.710_14.010 13.773 58.71 59.1 17.8 17.41 40.51 Pass Note: Cable correction factors are not included in this measurement as the low loss of the high quality TWINAX cable at low frequencies in practically non-existent. p1770014_FCC_Part 15.225_Rev 3.0 Page 8 of 14

Frequency Stability Engineer: Alex Macon Test Date: 9/20/17 Test Procedure The EUT was placed in an environmental test chamber and a frequency counter was utilized to verify that the frequency stability met the requirement for frequency stability across the temperature range from -20°C to +50°C. A variable DC power supply was used to vary the voltage from 85% to 115% of the rated voltage. Transmitter Frequency: 13.559291667 MHz Lower Limit: 13.5579357 MHz Upper Limit: 13.5606476 MHz Test Setup DC Power Frequency EUT Supply Counter Frequency Stability vs. Voltage 13.561 13.561 Upper Limit 13.560 Frequency (MHz) 13.560 Measured 13.559 Frequency 13.559 Lower Limit 13.558 13.558 10.00 10.50 11.00 11.50 12.00 12.50 13.00 13.50 14.00 Voltage Frequency Stability vs. Temperature 13.561 13.561 Upper Limit 13.560 Frequency (MHz) 13.560 Measured 13.559 Frequency 13.559 Lower Limit 13.558 13.558 -30 -20 -10 0 10 20 30 40 50 Temperature (Centigrade) *Note: The hardware is limited by the LCD screens minimum temperature rating of 0˚C p1770014_FCC_Part 15.225_Rev 3.0 Page 9 of 14

Radiated Emissions Engineer: Alex Macon Test Date: 9/20/17 Test Procedure The EUT was tested in a semi-anechoic chamber at a distance of 3 meters from the receiving antenna. A spectrum analyzer was used to verify that the UUT met the requirements for Radiated Emissions. The spectrum was examined from 9kHz to 1 GHz those emissions closest to their respective limits have been documented below. Test Setup Spectrum EUT Antenna Analyzer Radiated Emissions Emission Measured Antenna Antenna Turntable Limit Margin Frequency Value Height Polarity Position Detector (dBuV/m) (dB) (MHz) (dBuV/m) (cm) (dB) (degrees) 124.146 29.788 43.5 -13.712 400 V 241 PK 136.9357 31.247 43.5 -12.253 175 V 261 PK 593.8103 36.524 46 -9.476 325 V 292 PK 757.9441 36.528 46 -9.472 100 V 122 PK 996.3289 36.541 53.9 -17.359 400 V 127 PK 999.8816 38.704 53.9 -15.196 250 V 263 PK p1770014_FCC_Part 15.225_Rev 3.0 Page 10 of 14

Powerline Conducted Emissions Engineer: Alex Macon Test Date: 9/20/17 Test Procedure The EUT power cable connected to a LISN and the monitored output of the LISN was connected directly to a spectrum analyzer. The conducted emissions from 150 kHz to 30 MHz were monitored and compared to the specification limits. The average measurements were the worst case and are recorded in the tables below. Test Setup EUT LISN Spectrum Analyzer Power Cable Line 1 Peak Plot Line 2 Peak Plot All other results were greater than 20 dB below the limit. p1770014_FCC_Part 15.225_Rev 3.0 Page 11 of 14

Line 1 Neutral Avg Detector Measured LISN Correction Cable Loss Attenuator Final Data Limit Avg Margin Frequency Value Factor (dB) (dB) (dBuV) (dBuV) (dB) (dBuV) (dB) 439.4 KHz 16.51 0.1 0.03 10.1 26.74 47.731 -21.00 445.14 KHz 17.46 0.1 0.03 10.1 27.69 47.567 -19.88 457.45 KHz 12.97 0.1 0.03 10.1 23.20 47.216 -24.01 459.05 KHz 11.89 0.1 0.03 10.1 22.12 47.17 -25.05 490.33 KHz 13.09 0.1 0.03 10.1 23.32 46.276 -22.96 13.562 MHz 36.66 0 0.18 10.2 47.04 50 -2.96 Line2 Phase Avg Detector Measured LISN Correction Cable Loss Attenuator Final Data Limit Avg Margin Frequency Value Factor (dB) (dB) (dBuV) (dBuV) (dB) (dBuV) (dB) 476.09 KHz 15.62 0.1 0.03 10.1 25.85 46.683 -20.83 478.24 KHz 15.34 0.1 0.03 10.1 25.57 46.622 -21.06 491.23 KHz 14.12 0.1 0.03 10.1 24.35 46.251 -21.90 494.93 KHz 13.62 0.1 0.03 10.1 23.85 46.145 -22.30 495.1 KHz 13.81 0.1 0.03 10.1 24.04 46.14 -22.10 13.56 MHz 37.93 0 0.18 10.2 48.31 50 -1.69 Line 1 Neutral QP Detector Measured LISN Correction Cable Loss Attenuator Final Data Limit QP Margin Frequency Value Factor (dB) (dB) (dBuV) (dBuV) (dB) (dBuV) (dB) 439.4 KHz 32.84 0.1 0.03 10.1 43.07 57.731 -14.66 445.14 KHz 32.85 0.1 0.03 10.1 43.08 57.567 -14.49 457.45 KHz 30.46 0.1 0.03 10.1 40.69 57.216 -16.53 459.05 KHz 29.8 0.1 0.03 10.1 40.03 57.17 -17.14 490.33 KHz 29.21 0.1 0.03 10.1 39.44 56.276 -16.84 13.562 MHz 47.89 0 0.18 10.2 58.27 60 -1.73 Line 2 Phase 2 QP Detector Measured LISN Correction Cable Loss Attenuator Final Data Limit QP Margin Frequency Value Factor (dB) (dB) (dBuV) (dBuV) (dB) (dBuV) (dB) 476.09 KHz 28.66 0.1 0.03 10.1 38.89 56.683 -17.79 478.24 KHz 28.80 0.1 0.03 10.1 39.03 56.622 -17.59 491.23 KHz 28.03 0.1 0.03 10.1 38.26 56.251 -17.99 494.93 KHz 27.78 0.1 0.03 10.1 38.01 56.145 -18.14 495.1 KHz 28.29 0.1 0.03 10.1 38.52 56.14 -17.62 13.56 MHz 47.86 0 0.18 10.2 58.24 60 -1.76 p1770014_FCC_Part 15.225_Rev 3.0 Page 12 of 14

99% Occupied Bandwidth Engineer: Alex Macon Test Date: 9/12/17 Test Procedure The EUT was tested on an anechoic chamber at a distance of 1 meter from the receiving loop antenna. A spectrum analyzer was used to measure the 99% occupied bandwidth. Test Setup Spectrum EUT Antenna Analyzer 99% Bandwidth Summary Frequency Recorded Measurement Result (MHz) 13.56 847 Hz Pass p1770014_FCC_Part 15.225_Rev 3.0 Page 13 of 14

Test Equipment Utilized Description Manufacturer Model # CT Asset # Last Cal Date Cal Due Date Temperature Chamber Tenney Tenney Jr i00027 Verified on: 9/20/17 EMI Receiver HP 8546A i00033 3/28/17 3/28/18 Transient Limiter Com-Power LIT-153 i00123 Verified on: 9/20/17 Humidity / Temp Meter Newport IBTHX-W-5 i00282 6/9/17 6/9/18 Active Loop Antenna EMCO 6507 i00326 9/25/17 9/25/19 Spectrum Analyzer Agilent E4407B i00331 10/19/16 10/19/17 Data Logger Fluke Hydra Data Bucket i00343 5/25/17 5/25/18 Bi-Log Antenna Schaffner CBL 6111D i00349 8/3/16 8/3/18 AC Power Source Behlman BL 6000 i00362 Verified on: 9/20/17 EMI Analyzer Agilent E7405A i00379 2/22/17 2/22/18 3 Meter Semi-Anechoic 3 Meter Semi-Anechoic Panashield i00428 8/15/16 8/15/19 Chamber Chamber LISN COM-Power LI-125A i00447 9/11/17 9/11/19 LISN COM-Power LI-125A i00449 9/11/17 9/11/19 In addition to the above listed equipment standard RF connectors and cables were utilized in the testing of the described equipment. Prior to testing these components were tested to verify proper operation. END OF TEST REPORT p1770014_FCC_Part 15.225_Rev 3.0 Page 14 of 14


Document Created: 2018-01-19 16:24:06
Document Modified: 2018-01-19 16:24:06
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC