User manual

FCC ID: TM6DTC-CX24G

Users Manual

Download: PDF
FCCID_3842095

Mode Change CC 317 Press Mode key or C key to change mode. Backlight In any mode, press set key or press and hold mode key for 2 seconds to turn on Wheel Circumference the backlight. To get the accurate result, the wheel size should be Mode key Please check that all the following items have been included with the cycle computer correct. Mark the symbol on the tire and ride one circle. before starting. Then measure the length between two points to get the Specifications Stabling Pads x2 circumference. Or the user can also get wheel circumference by the following equation: Circumference (mm) = 2 x 3.14 x R (inch) x 2.54 (1 inch = 2.54 cm) Computer Speed & Cadence sensor R=Radius in centimeter White Black The user can refer the "wheel size chart" for the wheel size Cadence (Cadence (sensor) Magnet Magnet) The cycle computer main display and Key function Time Average Speed Maximum Speed Distance RS-200C cycle computer Current Speed compare to Average Speed Set Key PM Indicator Temperature (Post Meridiem) Speed Motion Signal x6 Pcs Bracket Rubber Magnet Current Speed Speed Scale Symbol Calculation Range Mode Indicator Sub Display Bracket Cycle Computer Odometer Calories consumption Bracket C key Rubber C(Clear)/RESET/OFF Nylon Ties Mode key / Backlight (Press 2 seconds to turn on the Backlight) Set mode In any page, press set key for 3 seconds to go into Setting mode. Press mode key for 3 seconds to save and exit. (1) (2) 1.Unit 2.Tire size 3.Time 4.Gender / Weight 5.ODO 6.Temperature Use the rubber to tighten the bracket to the handlebar or stem with the nylon ties. Average Cadence Maximum Cadence Trip Cadence Unit Tire size Pair device with sensor Maintenance RS-200C Series cycle computer If the display contrast changes and figures become faint, it's time to replace the battery. In any mode, press M+C Consider changing the computer sensor and transmitter batteries at the same time. and hold for 6 seconds. Note: KM/H+Kg+KM WS: 0100-2999mm Do not expose RS-200C Series computer to extremely cold or hot temperatures i.e. don't M/H+Lb+KM leave the unit in direct sunlight for extended periods of the time. Sensor Time Gender / Weight Check the position of sensor and magnet periodically. For current measurement, the sensor, (3) magnet should not get wet/ rust, otherwise it may cause inaccurate data. Bracket / Magnet / Sensor band Place the cycle computer on the bracket and secure it in clockwise. ODO Temperature These items can be rinsed in surface with fresh water or washed with a mild soap. Press and hold mode key for 3 seconds. Searching for 30 seconds. Battery replacement Check the position of the front fork to find the suitable point to attach the speed sensor. RS-200C Series cycle computer The maximum distance between cycle computer & the speed sensor is around 150 cm. 12H/24H H1(Male) Temperature Grently unscrew the back cover and avoid missing the Oring which attached in the cover. H2(Female) The (+) side should be facing up. Gently remove the battery and replace it with a new battery model CR2032. Save and exit Spoke 1~3mm Paired No Paired The battery symbol on the top left corner will show up when RS-200C Series cycle computer runnuing out of battery. Cadence sensor Speed sensor Time Gender / Weight Chainstay * It shows Red light when sensor is running out of battery. (non drive side) 1~3mm Next option Sensor: Front wheel Rear wheel Grently unscrew the back cover and avoid missing the Oring which attached in the cover. Next setting The (+) side should be facing up. Gently remove the battery and replace it with a new Hour(1-24) Weight: 20-150Kg Mount the sensor with nylon ties on the chosen front fork. Minute(0-59) 44-330Lb Revise the value battery model CR2032. After 5 seconds of receiving No paired Second(0-59) code from the sensor. 1:Please check if the How to mount the Magnet sensor is paired. Troubleshooting 2:Please check the status of the device’s battery. Q1. Display is black or very light: Cable tie Reset Cadence magnet The battery power may be low. Try to change the battery. In below page, press and hold C key for 3 seconds to reset the below data. Q2. Display becomes dark or black: The unit is too hot. Place the unit in a shaded area, and it will return to normal. Cadence sensor Q3. The unit operates slowly or struggled: The unit is too cold. Warm the unit, and it will return to normal. 1~3mm Auto wake up & Sleep Q4. Data in display varies enormously: Check the surroundings for electro magnetic or high energy interference and move Crank Pedal Auto wake up : If there is any speed or viberation, the computer will wake up from sleep 3 seconds mode. away from the source of interference. Auto sleep : If there is no speed or viberation for 6 minutes, the computer will go into Q5. Data in display shows slowly: sleep mode automatically. The unit may be affected by low temperature factor but it didn't influence the function Secure the Speed Magnet on the spoke of the wheel . Deep sleep : If auto wake up and sleep repeat 5 times, the computer will go into deep reading. When the temperature rises, the data reading/ witch will back to the normal. Make sure the magnet side faces the speed sensor zone. sleep. Users need to press key to wake up from Deep sleep. The maximum distance between the speed sensor and the magnet on the spoke is 5 mm. Q6. Current speed does not appear Once above items in the right position, the user may go for a ride. * In AVG. SPD page, if the trip time is more than 29:59:59 or the distance is more It may be caused by the following situation: the distance & position between Note:Please make sure everything has been setup correctly before riding the bicycle. than 999.99 KM, it will shows Err, please reset the data. magnet and sensor to adjust.

Limited warranty This product is for one year limited warranty commencing on the date of purchase. The product will be free from defects in material and workmanship for one year from the date of purchase. Warranty does not cover the batteries, damages due to misuse, abuse or accidents, cracked or broken cases, negligence of precautions, improper maintenance or commercial use. Warranty is void if the repairs are done by non authorized service technician. The warranties contained herein are expressly in lieu of any other warranties including implied warranty of merchantability and/ or fitness for purpose. In no event shall manufacturer be liable for any damages, direct or incidental, consequential or special, arising out of or related to the use of this manual or the products described herein. During this warranty period (one year) the product will either be repaired or replaced without charge. Important Health Notice!! Please read over the following information before using the Cycle computer. Never use the cycle computer in combination with other medical / implanted electronic equipment and device (especially heart pacemakers, EKG equipment, TENS equipment, cardio-pulmonary machines and pacemaker). If you are severely ill or pregnant, please consult your doctor before using cycle computer. Keep this device away from children. It contains batteries, which might be swallowed by children. As with most electronic receiving devices, there can sometimes be interference that causes inaccurate display readouts. Avoid using your cycle computer near commom sources of interference. These include high voltage power lines, air conditioning motor units, fluorescent lights, wristwatches, mobiles and computer. Federal Communication Commission Interference Statemen This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.


Document Created: 2018-05-07 17:04:27
Document Modified: 2018-05-07 17:04:27
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC