Modular Approval Request

FCC ID: TLZ-MF070

Cover Letter(s)

Download: PDF
FCCID_2334766

telefication RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00—1407) FCC ID: _TLZ—MFO70 Items to be covered Answerfrom applicant 1. The modular transmitter must have its own RF shielding. Yes, The EUT provides the RF shielding. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs The EUT hasits buffered are provided) to ensure that the module will comply with Part 15 requirements modulation. Please see the under conditions of excessive data rates or over—modulation. Schematic Diagram. 3. The modular transmitter must have its own power supply regulation. The EUT has its own power supply regulation. Please see the Schematic Diagram. 4. The modular transmitter must comply with the antenna requirements of Section The EUT has meets the FCC 15.203 and 15.204(c). The antenna must either be permanently attached or employ antenna requirements; unique a "unique" antenna coupler (at all connections between the module and the antenna, antenna connector and photo including the cable).. of antenna are shown in the test report. 5. The modular transmitter must be tested in a stand—alone configuration, i.e., the The EUT was testes in a module must not be inside another device during testing. This is intended to stand—alone configuration via demonstrate that the module is capable of complying with Part 15 emission limits a test kit. Please see section regardless of the device into which it is eventually installed. photographs oftest configuration in the test report. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the Please see exhibition label FCC ID is not visible when the module is installed inside another device, then the sample for the FCC ID ofthis outside of the device into which the module is installed must also display a label module. And also in the referring to the enclosed module. This exterior label can use wording such as the exhibition Users manual, following: "Contains Transmitter Module FCC ID: RX3—BRUCE—U" or "Contains there are instructions give to FCC ID: RX3—BRUCE—U." Any similar wording that expresses the same meaning the OEM on how to label the may be used. The Grantee may either provide such a label, an example of which end product. must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating The EUT is compliant with all requirements applicable to the transmitter and the manufacturer must provide applicable FCC rules. Details adequate instructions along with the module to explain any such requirements. A instructions for maintaining copy of these instructions must be included in the application for equipment compliance are give in the authorization. For example, there are very strict operational and timing User Manual. requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure The EUT is comply with RF requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific exposure re requirement. RF Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), exposure is addressed in the require that Unlicensed PCS, UNII and millimeter wave devices perform routine RF exposure exhibition. environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a "Limited Modular Approval" (LMA). Name and surname of applicant (or authorized representative):

telefication RF_734_00, Issue 1 Date: 90(% 7 (f\ Signature: fmr_ hn


Document Created: 2014-07-21 09:11:14
Document Modified: 2014-07-21 09:11:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC