TL-WCS200_user manual

FCC ID: TE7WCS200

Users Manual

Download: PDF

FCCID_3904046

LED Indication Status Specification Safety Information
Device
Charging
Fully
Charged
Removing
Device Standby Error
Input 5V 2A or 9V 1.67A Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use of the device.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
FCC RF Radiation Exposure Statement
(After Fully Charged)
Output 10W Max.
Please use this product carefully and operating at your own risk. protection against harmful interference in a residential installation. This equipment This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
· Keep the device away from water, fire, humidity or hot environments. generates, uses and can radiate radio frequency energy and, if not installed and used in environment. This device and its antenna must not be co-located or operating in conjunction with
/ / / accordance with the instructions, may cause harmful interference to radio communications.
Blue Light On
Blink
Continuously Attention · Do not attempt to disassemble, repair, or modify the device.
· Do not use damaged charger or USB cable to charge the device. However, there is no guarantee that interference will not occur in a particular installation. If
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
· Do not use the device where wireless devices are not allowed. this equipment does cause harmful interference to radio or television reception, which can be Mobile Configurations. The antennas used for this transmitter must be installed to provide a
determined by turning the equipment off and on, the user is encouraged to try to correct the separation distance of at least 20 cm from all persons and must not be co-located or operating in
/ / To begin fast wireless charging, place a mobile device that supports fast wireless charging
White Light On Light for 5s
Then Turn Off
Light for 5s
Then Turn Off on the TL-WCS200. For more information, please refer to the user manual. Explanation of the symbols on the product label interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
conjunction with any other antenna or transmitter.”

· Increase the separation between the equipment and receiver.
· You may need to purchase a charger separately depending on TL-WCS200. · Connect the equipment into an outlet on a circuit different from that to which the
Changing Mode · Depending on the location of the mobile wireless charging coil, your mobile device may
not charge properly.
DC voltage
receiver is connected. EU declaration of conformity
RECYCLING · Consult the dealer or an experienced radio/ TV technician for help.
· Wireless charging may not work properly if you have attached a thick case to your TP-Link hereby declares that the device is in compliance with the essential requirements and
This product bears the selective sorting symbol for Waste electrical and electronic This device complies with part 15 of the FCC Rules. Operation is subject to the following two
Pad Mode Stand Mode mobile device. If your case is thick, remove it before placing your mobile device on the
wireless charger. equipment (WEEE). This means that this product must be handled pursuant to conditions:
other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce
· If you connect a charger to the mobile device during wirless charging, the wireless European directive 2012/19/EU in order to be recycled or dismantled to minimize its · This device may not cause harmful interference.
charging feature will be unavailable. impact on the environment.User has the choice to give his product to a competent · This device must accept any interference received, including interference that may cause
The socket-outlet shall be installed near the equipment and shall be easily accessible. recycling organization or to the retailer when he buys a new electrical or undesired operation.
· Do not place foreign materials, such as metal objects, magnets, and magnetic electronic equipment. Any changes or modifications not expressly approved by the party responsible for RF Exposure Information
stripe cards, between the mobile device and the wireless charger. The mobile device compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
180 degree
may not charge properly.
· Use only chargers that comply with Limited Power Source (LPS) chargers that support
OPERATING FREQUENCY (the maximum H-field strength) unauthorized modifications to this equipment. Such modifications could void the user’s
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of
the general public to electromagnetic fields by way of health protection.
anti-clockwise fast charging. authority to operate the equipment. The device complies with RF specifications when the device used at 20 cm from your body.
rotation 110KHz-205KHz（-2.13dBuA/m）

Document Created: 2018-06-13 17:21:12
Document Modified: 2018-06-13 17:21:12

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC