5. User Manual

FCC ID: TE7EN020F5

Users Manual

Download: PDF
FCCID_4030740

Quick Installation Guide 300Mbps Wireless N Router EN020-F5 TL-WR850N TL-WR840N Connect the Hardware S/ WP ET S RE 4 3 Power adapter 2 1 If your Internet connection is through an Ethernet cable from the wall R WA N instead of through a DSL / Cable / Satellite modem, connect the WE PO Router Ethernet cable directly to the router’s WAN port as Step 2B, and then follow Step 4 and 5 to complete the hardware connection. 4 Connect the power adapter to the router. 2.B Connect the Ethernet cable Internet directly to the router’s WAN port. 1 Turn off the modem and remove the backup battery if it has one. 2.A Connect the modem to the router’s WAN port with an Ethernet cable. Power adapter Modem 5 Confirm that the following LEDs are solid and on to verify the hardware 3 Turn on the modem and connection is correct. then wait about2 minutes for it to restart. Power Wi-Fi Internet On On On

Configure the Router FAQ (Frequently Asked Questions) CE Declaration of conformity TP-Link hereby declares that this device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 1. Connect your computer to the router (Wired or Wireless) Q1. What can I do if the login window does not appear? 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce If the computer is set to a static or fixed IP address, change the settings OPERATING FREQUENCY(the maximum transmitted power) Wired to obtain an IP address automatically. 2400 MHz -2483.5 MHz(20dBm) Verify if http://tplinkwifi.netor http://192.168.0.1 is correctly entered in Safety Information below: the web browser. Alternatively, enter http://192.168.1.1 in the web Keep the device away from water, fire, humidity or hot environments. browser and press Enter. Adapter shall be installed near the equipment and shall be easily accessible. Use another web browser and try again. Do not attempt to disassemble, repair, or modify the device. Reboot your router and try again. Do not use damaged charger or USB cable to charge the device. Ethernet cable Disable then able the network adapter being used. Do not use any other chargers than those recommended. WAN 1 2 3 4 WPS/ RESET Do not use the device where wireless devices are not allowed. Q2. What can I do if I cannot access the Internet? Please read and follow the above safety information when operating the device.We cannot guarantee that no accidents or damage will occur due to Check if the Internet is working properly by connecting a computer improper use of device. Please use this product with care and operate at your own Wireless directly to the modem using an Ethernet cable. If it is not, contact your risk. Internet Service Provider. a Find the SSID (Network Name) Log in to the web management page of the router, and go to the Status and Wireless Password printed page to check whether the WAN IP address is valid or not. If it is, please on the label at the bottom of FCC Statement run the Quick Setup again; otherwise, recheck the hardware connection. the router. Reboot your router and try again. This equipment has been tested and found to comply with the limits for a Class B digital Wireless Password/PIN:XXXXXXXX SSID:TP-Link_XXXX For cable modem users, log in to the web management page of the device, pursuant to part 15 of the FCC Rules. These limits are designed to provide router. Go to Network > MAC Clone , click Clone MAC Address and click reasonable protection against harmful interference in a residential installation. This Save . Then reboot both the modem and the router. equipment generates, uses and can radiate radio frequency energy and, if not installed b Click the network icon of your computer or go to Wi-Fi Setting of your Q3. How do I restore the router to its factory default settings? and used in accordance with the instructions, may cause harmful interference to radio smart device, and then select the SSID to join the network. With the router powered on, use a pin to press and hold the WPS/ RESET communications. However, there is no guarantee that interference will not occur in a Computer Smart Device button on the back panel of the router for about 8 seconds. particular installation. If this equipment does cause harmful interference to radio or Log in to the web management page of the router, go to System Tools > < Settings Wi-Fi television reception, which can be determined by turning the equipment off and on, the Factory Defaults , and click Restore . The router will restore and reboot Connections are available automatically. user is encouraged to try to correct the interference by one or more of the following Wireless Network Connection Wi-Fi measures: OR CHOOSE A NETWORK... Q4. What can I do if I forget my web management page —Reorient or relocate the receiving antenna. TP-Link_XXXX password? —Increase the separation between the equipment and receiver. Connect automatically Connect TP-Link_XXXX Refer to FAQ > Q3 to reset the router,and then you can set up a new —Connect the equipment into an outlet on a circuit different from that to which the Other... password . receiver is connected. Q5. What can I do if I forget my wireless network password? —Consult the dealer or an experienced radio/TV technician for help. The factory default wireless password is printed on the label of the router. FCC Radiation Exposure Statement 2. Connect a computer directly to the router using an Ethernet cable. Log in This device complies with FCC radiation exposure limits set forth for an uncontrolled to the router’s web management page, and goWireless to > Wireless environment and it also complies with Part 15 of the FCC RF Rules. This equipment must A Launch a web browser, and enterhttp://tplinkwifi.netor http://192.168.0.1 in Security to obtain or reset your wireless password. the address bar. Create a password (1 - 15 characters) and get started. be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 Note: If the login window does not appear, please refer to FAQ > Q1. cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement. This device complies with Part 15 of the FCC Rules. Operation is subject to the following New Password two conditions: Low Middle High (1) this device may not cause harmful interference, and 7109505091 REV1.0.0 (2) this device must accept any interference received, including interference that may Let’s Get Started cause undesired operation. Caution! B Follow the step-by-step instructions of the Quick Setup to complete the Any changes or modifications not expressly approved by the party responsible for ©2018 TP-Link initial configuration. compliance could void the user's authority to operate the equipment.


Document Created: 2019-09-22 00:21:30
Document Modified: 2019-09-22 00:21:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC