14. Users Manual-1

FCC ID: TE7EAP245V3

Users Manual

Download: PDF
FCCID_4092316

1 Typical Network Topology Option 1: Ceiling Mounting A DHCP server (typically a router) with DHCP function enabled is required to assign IP addresses to the Note: Make sure that the ceiling tile is bigger than the EAP (206*182mm). EAPs and clients in your local network. Internet Quick Installation Guide Washers (Qty.3) M3×30 Pan-head Screws (Qty.3) Wing Nuts (Qty.3) AC1750 Wireless MU-MIMO Gigabit Ceiling Mount Access Point 1 EAP245 Router Remove the ceiling tile. Switch LED Indication Drill Hole for Ethernet cable X3 2 Place the mounting bracket in the center of the ceiling tile. Mark three positions for the screw holes and a position for the Ethernet cable hole. Drill three 4mm diameter holes for the Omada Controller screws and a 25mm diameter hole for the Ethernet cable at the marked positions. PC EAP EAP EAP Flashes Green Then Yellow Flashing Yellow Continuously The device has been powered on. System errors. RAM, Flash, Ethernet, WLAN or firmware may be malfunctioning. 3 Solid Green Flashing Green, Yellow Secure the mounting bracket to the The device is initializing or Firmware update is in progress. Do not ceiling tile using three M3x30 pan-head working properly. disconnect or power off the device. screws, washers and wing nuts, as shown on the left. Flashes Green Twice Flashes Yellow Once The initialization is completed. The device is being reset to its factory Clients default settings. Interface Panel 2 Hardware Installation The EAP can be ceiling-mounted or wall-mounted. 4 Feed the Ethernet cable through the hole and set the ceiling tile back into place. Option 1: Ceiling Mounting RESET With the device powered on, press and hold the button for about 5 seconds until the LED flashes yellow, then release the button. The device will restore to factory default settings. 5 Connect the Ethernet cable to the ETH1 (PoE) ETHERNET port. Attach the EAP to the The port is used to connect to the PoE port of the provided PoE adapter or a PSE (Power Option 2: Wall Mounting mounting bracket by aligning the arrow Sourcing Equipment), such as a PoE switch, for both data transmission and Power over mark on the EAP with the arrow mark Ethernet (PoE) through Ethernet cable. on the mounting bracket, then rotate the EAP until it is locked into place, as shown ETH2 on the left. The port is a Gigabit Ethernet port used for bridging.

Option 2: Wall Mounting Tip: 4 Software Configurations To remove the EAP from the mounting bracket, insert a paper clip in the Security Slot to Note: For security reasons, it is recommended not to install the EAP with the louver downward. release the Locking Tab and rotate the EAP until it is detached from the mounting bracket, as shown below. The EAP supports two configuring options: To configure and manage mass EAPs via centralized controller software, please refer to Option 1. To configure a single EAP via a web browser directly, please refer to Option 2. D3×28 Plastic Wall Anchors (Qty.3) S3×20 Self-tapping Screws (Qty.3) Locking Tab Security Slot Option 1: Via Omada Controller X3 1 If your Ethernet cable feeds Step 1: Installing Omada Controller through the wall, you can On the PC, download the Omada Controller installation file from position the mounting bracket to https://www.tp-link.com/en/download/EAP-Controller.html. Run the file and follow the make the cable through the wizard to install the Omada Controller. fixing hole. Mark three positions for the screw holes and then drill three 6mm diameter holes at the Step 2: Configuring Omada Controller marked positions. Launch the Omada Controller and follow the step-by-step instructions to complete 3 Power Supply the Quick Setup. After the wizard is finished, a login screen will appear. Step 3: Logging in to Omada Controller The EAP can be powered via a PSE device (such as a PoE switch) or a power adapter. Enter the admin name and password you created and click Sign In. Then you can 2 further configure the Omada Controller. Insert the plastic wall anchors Via PoE Switch into the 6mm diameter holes. For detailed configurations, please visit https://www.tp-link.com/support to Connect an Ethernet cable from the PoE switch to the ETH1 (PoE) port. download the User Guide of Omada Controller in the download center. Option 2: Via Web Browser Note: Before connecting to the EAP wirelessly via the default SSID, make sure that your network has a DHCP server (typically a router ) with DHCP function enabled to assign IP addresses to the EAPs and wireless devices. 3 PoE Switch Secure the mounting bracket Step 1: Connecting to the EAP Device to the wall by driving the Power on the EAP and connect wirelessly by using the default SSID (format: self-tapping screws into the anchors. Make sure that the TP-Link_2.4GHz/5GHz_XXXXXX) printed on the product label. shoulders of the mounting bracket are on the outside. Step 2: Logging in to the EAP Device Via PoE Adapter Launch a web browser and enter http://tplinkeap.net in the address bar. Use admin for both Username and Password to log in. The EAP can be powered via the provided PoE adapter. Step 3: Configuring the EAP Device 4 Set up a new Username and Password for secure management purpose. Modify the Connect the Ethernet cable to 3 wireless parameters and reconnect your wireless devices to the new wireless network. the ETHERNET port on the EAP. For detailed configurations, please visit https://www.tp-link.com/support to download PoE Adapter the User Guide of EAP in the download center. PoE LAN Switch 1 2 5 (Up to 100m) ©2018 TP-Link 7106508097 REV3.0.1 Attach the EAP to the mounting bracket by aligning the arrow 1 Connect the ETH1 (PoE) port to the PoE port of the PoE adapter using an Ethernet cable. For technical support, User Guide and other information, please mark on the EAP with the The cable length can be up to 100 meters. visit https://www.tp-link.com/support, or simply scan the QR code. arrow mark on the mounting The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU 2 Connect the Ethernet cable from the switch to the LAN port of the PoE adapter. bracket, then rotate the EAP General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under (https://www.tp-link.com/en/support/gpl/). The until it is locked into place, as 3 Plug the female connector of the provided power cord into the power adapter, and the respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more authors. For shown on the left. male connector to a power outlet. details, see the GPL Code and other terms of the GPL.


Document Created: 2018-05-23 17:38:28
Document Modified: 2018-05-23 17:38:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC