Cal cert Mixer FSZ170

FCC ID: TA8AKRD901079

Test Report

Download: PDF
FCCID_4158068

Calibration Certificate Certificate Number 24-0170-100974-01 Kalibrierschein Zertifikatsnummer This calibration certificate documents, that Unit Data the named item is tested and measured Item Harmonic Mixer, 110 GHz to 170 GHz against defined specifications. Measurement Gegenstand results are located usually in the Manufacturer RPG corresponding interval with a probability of Hersteller approx. 95% (coverage factor k = 2). Calibration is performed with test equipment Type RPG FS-Z170 and standards directly or indirectly traceable Typ by means of approved calibration techniques Material Number 3622.0714.02 Serial Number 100974 to the PTB/DKD or other Materialnummer Seriennummer national/international standards, which realize the physical units of measurement Asset Number Inventarnummer according to the International System of Units (SI). In all cases where no standards are available, measurements are referenced to standards of the R&S laboratories. Principles Order Data and methods of calibration correspond with Customer EN ISO/IEC 17025. This calibration certificate Auftraggeber may not be reproduced other than in full. Calibration certificates without signatures are not valid. The user is obliged to have the object recalibrated at appropriate intervals. Order Number Dieser Kalibrierschein dokumentiert, dass der Bestellnummer genannte Gegenstand nach festgelegten Vorgaben geprüft und gemessen wurde. Die Date of Receipt Eingangsdatum Messwerte lagen im Regelfall mit einer Wahrscheinlichkeit von annähernd 95% im Performance zugeordneten Werteintervall (Erweiterte Messunsicherheit mit k = 2). Die Kalibrierung Place and Date of Calibration Meckenheim, 2018-02-05 erfolgte mit Messmitteln und Normalen, die direkt Ort und Datum der Kalibrierung oder indirekt durch Ableitung mittels anerkannter Scope of Calibration Standard Calibration Kalibriertechniken rückgeführt sind auf Normale Umfang der Kalibrierung der PTB/DKD oder anderer Statement of Compliance New device nationaler/internationaler Standards zur (Incoming) Darstellung der physikalischen Einheiten in Konformitätsaussage Übereinstimmung mit dem Internationalen (Anlieferung) Einheitensystem (SI). Wenn keine Normale existieren, erfolgt die Rückführung auf Bezugsnormale der R&S-Laboratorien. Statement of Compliance All measured values are within the data sheet Grundsätze und Verfahren der Kalibrierung beziehen sich auf EN ISO/IEC 17025. Dieser (Outgoing) specifications. Konformitätsaussage Kalibrierschein darf nur vollständig und (Auslieferung) unverändert weiterverbreitet werden. Extend of Calibration Documents 2 pages Calibration Certificate Kalibrierscheine ohne Unterschriften sind Umfang des Kalibrierdokuments 5 pages Outgoing Results ungültig. Für die Einhaltung einer angemessenen Frist zur Wiederholung der Kalibrierung ist der Benutzer verantwortlich. Radiometer Physics GmbH; Meckenheim Date of Issue Head of Laboratory Person Responsible Ausstellungsdatum Laborleitung Bearbeiter 2018-02-05 Schulze Dick Page (Seite) 1/2 Vers2010-05-05/ RPG2014-02-28 Radiometer Physics GmbH ● Werner-von-Siemens-Str. 4 ● 53340 Meckenheim ● Telephone national: 02225/99981-0 international: 0049 2225-99981-0 Fax: 02225/99981-99 ● Managing Director: Achim Walber, Dr. Thomas Rose ● Company's Place of Business: Meckenheim Commercial Register No.: Bonn, HRB 10291 ● VAT Identification No.: DE 123 377 395

Material Number 3622.0714.02 Serial Number 100974 Certificate Number 24-0170-100974-01 Calibration Method RPG-PAQA-TN-2014-002 Relative Humidity 20 % - 80 % Kalibrieranweisung Relative Luftfeuchte +7 Ambient Temperature (23 -3 ) °C Umgebungstemperatur Working standards used (having a significant effect on the accuracy) Verwendete Gebrauchsnormale (mit signifikantem Einfluss auf die Genauigkeit) Item Type Serial Number Calibration Certificate Number Cal. Due Gegenstand Typ Seriennummer Kalibrierscheinnummer Kalibr. bis Vector Network Analyzer R&S® ZVA67 101097 20-300432406 2020-07-21 Powersensor R&S® NRP-Z55 140093 20-300426315 2018-05-17 UGB1 A compliance statement may be possible where a confidence level of less than 95 % is acceptable. Die Bestätigung der Konformität ist möglich, sofern ein Grad des Vertrauens von weniger als 95 % akzeptabel ist. UGB2 A non-compliance statement may be possible where a confidence level of less than 95 % is acceptable. Die Bestätigung der Nicht-Konformität ist möglich, sofern ein Grad des Vertrauens von weniger als 95 % akzeptabel ist. Ref.: ILAC-G8:03/2009 ‘Guidelines on the Reporting of Compliance with Specification’. Notes Anmerkungen If the new product is stored under the climate conditions as specified in the data sheet upon delivery, the product’s accuracy is not significantly affected within 12 month after its calibration in our factory. In this case, the recommended calibration interval starts on the date when the product is actually put into operation. Page 2/2

Material Number 3622.0714.02 Serial Number 100974 Certificate Number 24-0170-100974-01 Outgoing Results The following abbreviations may be used in this document {a} No measurement uncertainty stated because the errors always add together. So it is sure that a measurement result evaluated as "PASS" is pass. {b} The measurement uncertainty depends on the measurement result. The stated measurement uncertainty is valid for the close area around the specification. Measurement results outside the close area have a higher measurement uncertainty but are within the specification. {c} Functional test, therefore no measurement uncertainty is stated. {d} Typical value, refer to performance test. {e} The measurement uncertainty is taken into account when setting the measuring system. DL or DT Data Limit for symmetrical tolerance limits DLL Datasheet Lower Limit DUL Datasheet Upper Limit MU Measurement Uncertainty MLL or MLV Measurement Uncertainty Lower Value MUL or MUV Measurement Uncertainty Upper Value Nom. Nominal Value Dev. Deviation MErr. Measurement Error Act. Actual Value UGB Uncertainty Guard Band: Measuring uncertainty violates the data (spec.) limit. UGB1 Measurement results marked as UGB1 show conformity with a probability of >50 %and <95 %. UGB2 Measurement results marked as UGB2 show non-conformity with a probability of >50 %and <95 %. DU Datasheet Uncertainty Explanation of charts Page 1/5

Material Number 3622.0714.02 Serial Number 100974 Certificate Number 24-0170-100974-01 Software used for measurement Item Type Version Remark Measurement Studio Professional Edition 2013 MixerCertification 7_08 Page 2/5

Material Number 3622.0714.02 Serial Number 100974 Certificate Number 24-0170-100974-01 1.1 RF Input – VSWR Measurement uncertainty: 0.05 (VSWR) Page 3/5

Material Number 3622.0714.02 Serial Number 100974 Certificate Number 24-0170-100974-01 1.2 Conversion loss LO level +15.5 dBm nominal Bias 0A Measurement uncertainty: 1.5 dB Note: Numeric calibration data can be found attached to the PDF file of the calibration certificate. Click the “paper clip” symbol to display the file. The file has been renamed for safety reasons. When downloading the file onto your PC, please delete the “.file” extension and unzip the data. Page 4/5

Material Number 3622.0714.02 Serial Number 100974 Certificate Number 24-0170-100974-01 1.3 Frequency response within 1 GHz DUL Actual Evaluation (worst case) IF = 404.4 MHz, 6 dB 2.14 dB PASS 12th harmonic IF = 729 MHz, 6 dB 2.15 dB PASS 12th harmonic IF = 1330 MHz, 6 dB 1.99 dB PASS 10th harmonic Page 5/5


Document Created: 2018-02-05 11:48:20
Document Modified: 2018-02-05 11:48:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC