test report part 4 of 4

FCC ID: TA8AKRC161752-1

Test Report

Download: PDF
FCCID_4098786

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-21: Conducted spurious emissions for multi band B5 10 MHz low Figure 8.5-22: Conducted spurious emissions for multi band B5 10 MHz low channel, B12A 10 MHz low channel with 40 W configuration at Port C channel, B12A 10 MHz low channel with 40 W configuration at Port D Figure 8.5-23: Conducted spurious emissions for multi band B5 10 MHz low Figure 8.5-24: Conducted spurious emissions for multi band B5 10 MHz low channel, B12A 10 MHz low channel with 60 W configuration at Port A channel, B12A 10 MHz low channel with 40 W configuration at Port C Report reference ID: 362902-1TRFWL-R1 Page 94 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-25: Conducted spurious emissions for multi band B5 10 MHz mid Figure 8.5-26: Conducted spurious emissions for multi band B5 10 MHz mid channel, B12A 10 MHz mid channel with 40 W configuration at Port A channel, B12A 10 MHz mid channel with 40 W configuration at Port B Figure 8.5-27: Conducted spurious emissions for multi band B5 10 MHz mid Figure 8.5-28: Conducted spurious emissions for multi band B5 10 MHz mid channel, B12A 10 MHz mid channel with 40 W configuration at Port C channel, B12A 10 MHz mid channel with 40 W configuration at Port D Report reference ID: 362902-1TRFWL-R1 Page 95 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-29: Conducted spurious emissions for multi band B5 10 MHz mid Figure 8.5-30: Conducted spurious emissions for multi band B5 10 MHz mid channel, B12A 10 MHz mid channel with 60 W configuration at Port A channel, B12A 10 MHz mid channel with 60 W configuration at Port C Figure 8.5-31: Conducted spurious emissions for multi band B5 10 MHz high Figure 8.5-32: Conducted spurious emissions for multi band B5 10 MHz high channel, B12A 10 MHz high channel with 40 W configuration at Port A channel, B12A 10 MHz high channel with 40 W configuration at Port B Report reference ID: 362902-1TRFWL-R1 Page 96 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-33: Conducted spurious emissions for multi band B5 10 MHz high Figure 8.5-34: Conducted spurious emissions for multi band B5 10 MHz high channel, B12A 10 MHz high channel with 40 W configuration at Port C channel, B12A 10 MHz high channel with 40 W configuration at Port D Figure 8.5-35: Conducted spurious emissions for multi band B5 10 MHz high Figure 8.5-36: Conducted spurious emissions for multi band B5 10 MHz high channel, B12A 10 MHz high channel with 60 W configuration at Port A channel, B12A 10 MHz high channel with 60 W configuration at Port C Report reference ID: 362902-1TRFWL-R1 Page 97 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-37: Conducted spurious emissions for multi band B5 MC 2×5 MHz Figure 8.5-38: Conducted spurious emissions for multi band B5 MC 2×5 MHz channel, B12A MC 2×5 MHz low channel with 40 W configuration at Port A channel, B12A MC 2×5 MHz channel with 40 W configuration at Port B Figure 8.5-39: Conducted spurious emissions for multi band B5 MC 2×5 MHz Figure 8.5-40: Conducted spurious emissions for multi band B5 MC 2×5 MHz channel, B12A MC 2×5 MHz low channel with 40 W configuration at Port C channel, B12A MC 2×5 MHz channel with 40 W configuration at Port D Report reference ID: 362902-1TRFWL-R1 Page 98 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-41: Conducted spurious emissions for multi band B5 MC 2×5 MHz Figure 8.5-42: Conducted spurious emissions for multi band B5 MC 2×5 MHz channel, B12A MC 2×5 MHz low channel with 60 W configuration at Port A channel, B12A MC 2×5 MHz channel with 60 W configuration at Port C Figure 8.5-43: Conducted spurious emissions for multi band B5 MC 3×5 MHz Figure 8.5-44: Conducted spurious emissions for multi band B5 MC 3×5 MHz channel, B12A MC 2×5 MHz low channel with 40 W configuration at Port A channel, B12A MC 2×5 MHz channel with 40 W configuration at Port B Report reference ID: 362902-1TRFWL-R1 Page 99 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-45: Conducted spurious emissions for multi band B5 MC 3×5 MHz Figure 8.5-46: Conducted spurious emissions for multi band B5 MC 3×5 MHz channel, B12A MC 2×5 MHz low channel with 40 W configuration at Port C channel, B12A MC 2×5 MHz channel with 40 W configuration at Port D Figure 8.5-47: Conducted spurious emissions for multi band B5 MC 3×5 MHz Figure 8.5-48: Conducted spurious emissions for multi band B5 MC 3×5 MHz channel, B12A 10 MHz channel and IoT with 40 W configuration at Port A channel, B12A 10 MHz channel and IoT with 40 W configuration at Port B Report reference ID: 362902-1TRFWL-R1 Page 100 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-49: Conducted spurious emissions for multi band B5 MC 3×5 MHz Figure 8.5-50: Conducted spurious emissions for multi band B5 MC 3×5 MHz channel, B12A 10 MHz channel and IoT with 40 W configuration at Port C channel, B12A 10 MHz channel and IoT with 40 W configuration at Port D Figure 8.5-51: Conducted spurious emissions for multi band B5 MC 3×5 MHz Figure 8.5-52: Conducted spurious emissions for multi band B5 MC 3×5 MHz channel, B12A 10 MHz channel and IoT with 60 W configuration at Port A channel, B12A 10 MHz channel and IoT with 60 W configuration at Port C Report reference ID: 362902-1TRFWL-R1 Page 101 of 118

Section 8 Testing data Test name Spurious emissions at RF antenna connector (multi band B5 and B12A) Specification FCC Parts 22 and 27, RSS-130 and RSS-132 Figure 8.5-53: Conducted spurious emissions for multi band B5 MC 2×10 Figure 8.5-54: Conducted spurious emissions for multi band B5 MC 2×10 MHz channel, B12A 5 and 10 MHz channel and IoT with 60 W configuration MHz channel, B12A 5 and 10 MHz channel and IoT with 60 W configuration at Port A at Port C Report reference ID: 362902-1TRFWL-R1 Page 102 of 118

Section 8 Testing data Test name Clause 27.53 and 22.917(a) Radiated spurious emissions Specification FCC Part 27 and Part 22 8.6 Radiated spurious emissions 8.6.1 Definitions and limits FCC P27, FCC P22, RSS-130 and RSS-132 Out of band emissions. The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. (b) Measurement procedure. Compliance with these rules is based on the use of measurement instrumentation employing a reference bandwidth as follows: (1) In the spectrum below 1 GHz, instrumentation should employ a reference bandwidth of 100 kHz or greater. In the 1 MHz bands immediately outside and adjacent to the frequency block, a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. A narrower resolution bandwidth is permitted in all cases to improve measurement accuracy, provided that the measured power is integrated over the full required reference bandwidth (i.e., 100 kHz or 1 percent of emission bandwidth, as specified). The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emissions are attenuated at least 26 dB below the transmitter power. (2) In the spectrum above 1 GHz, instrumentation should employ a reference bandwidth of 1 MHz. (c) Alternative out of band emission limit. Licensees in this service may establish an alternative out of band emission limit to be used at specified band edge(s) in specified geographical areas, in lieu of that set forth in this section, pursuant to a private contractual arrangement of all affected licensees and applicants. In this event, each party to such contract shall maintain a copy of the contract in their station files and disclose it to prospective assignees or transferees and, upon request, to the FCC. 8.6.2 Test summary Test date November 1, 2018 Temperature 22 °C Test engineer Shaen He Air pressure 1000 mbar Verdict Pass Relative humidity 30 % 8.6.3 Observations, settings and special notes The spectrum was searched from 30 MHz to the 10 th harmonic. All measurements were performed using a peak detector. RBW within 30–1000 MHz was 100 kHz and 1 MHz above 1 GHz. VBW was wider than RBW. Testing was performed with all RF ports terminated with 50 Ohm load. Band 5 and Band 12A simultaneous transmission was tested as a worst-case emissions scenario. Report reference ID: 362902-1TRFWL-R1 Page 103 of 118

Section 8 Testing data Test name Clause 27.53 and 22.917(a) Radiated spurious emissions Specification FCC Part 27 and Part 22 8.6.4 Test data 90 80 70 60 Level in dBµV/m 50 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 5MHz Bottom -13 dBm (82.23 dBuV) PK+_MAXH Figure 8.6-1: Radiated spurious emission below 1 GHz, B5 and B12A at low 5 MHz channel 90 80 70 60 Level in dBµV/m 50 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 5MHz Middle -13 dBm (82.23 dBuV) PK+_MAXH Figure 8.6-2: Radiated spurious emission below 1 GHz, B5 and B12A at mid 5 MHz channel Report reference ID: 362902-1TRFWL-R1 Page 104 of 118

Section 8 Testing data Test name Clause 27.53 and 22.917(a) Radiated spurious emissions Specification FCC Part 27 and Part 22 90 80 70 60 Level in dBµV/m 50 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 5MHz High -13 dBm (82.23 dBuV) PK+_MAXH Figure 8.6-3: Radiated spurious emission below 1 GHz, B5 and B12A at high 5 MHz channel 100 -13 dBm in dBuV 90 80 70 60 Level in dBµV/m 50 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 10MHz Bottom -13 dBm in dBuV PK+_MAXH Figure 8.6-4: Radiated spurious emission below 1 GHz, B5 and B12A at low 10 MHz channel Report reference ID: 362902-1TRFWL-R1 Page 105 of 118

Section 8 Testing data Test name Clause 27.53 and 22.917(a) Radiated spurious emissions Specification FCC Part 27 and Part 22 100 -13 dBm in dBuV 90 80 70 60 Level in dBµV/m 50 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 10MHz Middle -13 dBm in dBuV PK+_MAXH Figure 8.6-5: Radiated spurious emission below 1 GHz, B5 and B12A at mid 10 MHz channel 90 80 70 60 Level in dBµV/m 50 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz 10MHz High -13 dBm (82.23 dBuV) PK+_MAXH Figure 8.6-6: Radiated spurious emission below 1 GHz, B5 and B12A at high 10 MHz channel Report reference ID: 362902-1TRFWL-R1 Page 106 of 118

Section 8 Testing data Test name Clause 27.53 and 22.917(a) Radiated spurious emissions Specification FCC Part 27 and Part 22 90 80 70 60 Level in dBµV/m 50 40 30 20 10 0 1G 2G 3G 4G 5G 6 7 8 9G Frequency in Hz B5 10 MHz Middle B12 10 MHz Middle with GB FCC Part 15 and ICES- Class B 3m Peak Limit FCC Part 15 and ICES - Class B 3m Average Limit -13 dBm equiv 82.23 dBuV Preview Result 1-PK+ Final_Result CAV Figure 8.6-7: Radiated spurious emission above 1 GHz, B5 and B12A at mid 10 MHz channel Note: there is no observable difference between 5 MHz and 10 MHz channels results at low, mid or high channels, so one repres entative plot was recorded. Report reference ID: 362902-1TRFWL-R1 Page 107 of 118

Section 8 Testing data Test name FCC 27.54 and RSS-130 4.3 Frequency stability (B12A) Specification FCC Part 27 and RSS-130 8.7 FCC 27.54 and RSS-130 4.3 Frequency stability (B12A) 8.7.1 Definitions and limits FCC: The frequency stability shall be sufficient to ensure that the fundamental emissions stay within the authorized bands of operation. ISED: The transmitter frequency stability limit shall be determined as follows: • (a) The frequency offset shall be measured according to the procedure described in RSS-Gen and recorded; • (b) Using a resolution bandwidth of 1% of the occupied bandwidth, a reference point at the unwanted emission level which complies with the attenuation of 43 + 10 log10 p (watts) on the emission mask of the lowest and highest channel shall be selected, and the frequency at these points shall be recorded as fL and fH respectively. The applicant shall ensure frequency stability by showing that fL minus the frequency offset and fH plus the frequency offset shall be within the frequency range in which the equipment is designed to operate 8.7.2 Test summary Test date October 25, 2018 8.7.3 Observations, settings and special notes None 8.7.4 Test data Table 8.7-1: Frequency error results Temperature, °C Voltage, VDC Frequency error, Hz +50 48.0 -1.1 +40 48.0 -0.6 +30 48.0 -0.3 +20 55.2 -0.7 +20 48.0 -0.6 +20 40.8 -0.8 +10 48.0 0.8 0 48.0 0.9 −10 48.0 -0.7 −20 48.0 0.7 −30 48.0 -0.8 Report reference ID: 362902-1TRFWL-R1 Page 108 of 118

Section 8 Testing data Test name FCC 22.355 and RSS-132 5.3 Frequency tolerance (B5) Specification FCC Part 22 and RSS-132 8.8 FCC 22.355 and RSS-132 5.3 Frequency tolerance (B5) 8.8.1 Definitions and limits FCC: The carrier frequency of each transmitter in the Public Mobile Services must be maintained within the tolerance of ±1.5 ppm for Base/fixed stations operating within 821–896 MHz. ISED: The carrier frequency shall not depart from the reference frequency in excess of ±2.5 ppm for mobile stations and ±1.5 ppm for base stations. In lieu of meeting the above stability values, the test report may show that the frequency stability is sufficient to ensure that the occupied bandwidth stays within each of the sub-bands (see Section 5.1) when tested to the temperature and supply voltage variations specified in RSS-Gen. 8.8.2 Test summary Test date October 25, 2018 8.8.3 Observations, settings and special notes 1.5 ppm of 881.5 MHz is 1322 Hz. 8.8.4 Test data Table 8.8-1: Frequency tolerance results Temperature, °C Voltage, VDC Frequency error, Hz Limit, ±Hz +50 48.0 -0.8 1322 +40 48.0 -0.9 1322 +30 48.0 -1.0 1322 +20 55.2 -0.9 1322 +20 48.0 -1.1 1322 +20 40.8 0.7 1322 +10 48.0 -1.2 1322 0 48.0 -1.0 1322 −10 48.0 0.9 1322 −20 48.0 -0.7 1322 −30 48.0 1.0 1322 Report reference ID: 362902-1TRFWL-R1 Page 109 of 118

Section 8 Testing data Test name FCC Part 2.1049 and RSS-Gen 6.7 Occupied bandwidth (B12A) Specification FCC Part 2 and RSS-Gen, Issue 5 8.9 FCC Part 2.1049 and RSS-Gen 6.7 Occupied bandwidth (B12A) 8.9.1 Definitions and limits FCC: The emission bandwidth is defined as the width of the signal between two points, one below the carrier cent er frequency and one above the carrier center frequency, outside of which all emissions are attenuated at least 26 dB below the transmitter power. ISED: The occupied bandwidth or the “99% emission bandwidth” is defined as the frequency range between two points, one above and the other below the carrier frequency, within which 99% of the total transmitted power of the fundamental transmitted emission is contained. The occupied bandwidth shall be reported for all equipment in addition to the specified bandwidth required in the applicable RSSs. 8.9.2 Test summary Test date October 24, 2018 8.9.3 Observations, settings and special notes None 8.9.4 Test data Table 8.9-1: Occupied bandwidth measurement results for 40 W operation (Configuration 1) 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, Remarks Port A, MHz Port A, MHz Port B, MHz Port B, MHz Port C, MHz Port C, MHz Port D, MHz Port D, MHz 5M bottom (QPSK) 4.79 4.47 4.81 4.48 4.80 4.50 4.79 4.48 5M bottom (16QAM) 4.78 4.46 4.76 4.47 4.73 4.49 4.78 4.47 5M bottom (64QAM) 4.79 4.48 4.81 4.49 4.78 4.49 4.79 4.48 5M bottom (256QAM) 4.81 4.48 4.81 4.48 4.79 4.49 4.75 4.48 10M bottom (QPSK) 9.63 8.95 9.55 8.96 9.62 8.95 9.57 8.95 10M bottom + IoT 9.76 9.40 9.73 9.39 9.70 9.40 9.72 9.40 5M middle (QPSK) 4.80 4.48 4.80 4.48 4.78 4.48 4.82 4.48 10M middle (QPSK) 9.61 8.93 9.47 8.95 9.53 8.95 9.51 8.96 10M middle + IoT 9.74 9.40 9.73 9.41 9.69 9.40 9.70 9.40 5M top (QPSK) 4.77 4.48 4.79 4.49 4.82 4.49 4.80 4.48 10M top (QPSK) 9.61 8.94 9.56 8.95 9.53 8.96 9.61 8.95 10M top + IoT 9.76 9.40 9.77 9.40 9.72 9.40 9.74 9.40 Table 8.9-2: Occupied bandwidth measurement results for 60 W operation (Configuration 2) 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, Remarks Port A, MHz Port A, MHz Port C, MHz Port C, MHz 10M bottom (QPSK) 9.51 8.94 9.53 8.94 10M bottom + IoT 9.72 9.38 9.66 9.37 5M middle (QPSK) 4.81 4.48 4.80 4.48 10M middle (QPSK) 9.59 8.94 9.60 8.85 10M middle + IoT 9.76 9.4 9.73 9.41 5M top (QPSK) 4.77 4.48 4.80 4.48 10M top (QPSK) 9.60 8.94 9.55 8.95 10M top + IoT 9.73 9.4 9.74 9.39 Report reference ID: 362902-1TRFWL-R1 Page 110 of 118

Section 8 Testing data Test name FCC Part 2.1049 and RSS-Gen 6.7 Occupied bandwidth (B12A) Specification FCC Part 2 and RSS-Gen, Issue 5 Figure 8.9-1: Occupied bandwidth 5 MHz channel, sample plot Figure 8.9-2: Occupied bandwidth 10 MHz channel, sample plot Figure 8.9-3: Occupied bandwidth 10 MHz channel and IoT, sample plot Report reference ID: 362902-1TRFWL-R1 Page 111 of 118

Section 8 Testing data Test name FCC Part 22.917(b) and RSS-Gen 6.7 Occupied bandwidth (B5) Specification FCC Part 22 and RSS-Gen, Issue 5 8.10 FCC Part 22.917(b) and RSS-Gen 6.7 Occupied bandwidth (B5) 8.10.1 Definitions and limits FCC: The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and o ne above the carrier center frequency, outside of which all emissions are attenuated at least 26 dB below the transmitter power. ISED: The occupied bandwidth or the “99% emission bandwidth” is defined as the frequency range between two points, one above and the other below the carrier frequency, within which 99% of the total transmitted power of the fundamental transmitted emission is contained. The occupied bandwidth shall be reported for all equipment in addition to the specified bandwidth required in the applicable RSSs. 8.10.2 Test summary Test date October 24, 2018 8.10.3 Observations, settings and special notes EUT was assessed and tested for worst case configurations: LTE + NB IoT (GB) 8.10.4 Test data Table 8.10-1: Occupied bandwidth measurement results for 40 W operation (Configuration 1) 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, Remarks Port A, MHz Port A, MHz Port B, MHz Port B, MHz Port C, MHz Port C, MHz Port D, MHz Port D, MHz 5M bottom (QPSK) 4.77 4.48 4.76 4.48 4.77 4.48 4.79 4.48 5M bottom (16QAM) 4.77 4.48 4.75 4.48 4.76 4.46 4.77 4.46 5M bottom (64QAM) 4.78 4.48 4.77 4.48 4.76 4.48 4.79 4.47 5M bottom (256QAM) 4.78 4.47 4.78 4.48 4.79 4.70 4.77 4.48 10M bottom (QPSK) 9.53 8.94 9.44 8.95 9.56 8.96 9.59 8.95 5M middle (QPSK) 4.77 4.48 4.78 4.48 4.79 4.49 4.78 4.48 10M middle (QPSK) 9.61 8.94 9.55 8.94 9.55 8.96 9.57 8.94 5M top (QPSK) 4.79 4.48 4.76 4.48 4.78 4.47 4.79 4.47 10M top (QPSK) 9.54 8.95 9.63 8.95 9.48 8.93 9.52 8.95 Table 8.10-2: Occupied bandwidth measurement results for 60 W operation (Configuration 2) 26 dB BW, 99% OBW, 26 dB BW, 99% OBW, Remarks Port A, MHz Port A, MHz Port C, MHz Port C, MHz 5M bottom (QPSK) 4.80 4.48 4.80 4.48 10M bottom (QPSK) 9.54 8.94 9.60 8.95 5M middle (QPSK) 4.79 4.48 4.79 4.48 10M middle (QPSK) 9.60 8.97 9.57 8.85 5M top (QPSK) 9.52 8.94 9.57 8.84 10M top (QPSK) 4.80 4.48 4.80 4.48 Report reference ID: 362902-1TRFWL-R1 Page 112 of 118

Section 8 Testing data Test name FCC Part 22.917(b) and RSS-Gen 6.7 Occupied bandwidth (B5) Specification FCC Part 22 and RSS-Gen, Issue 5 Figure 8.10-1: Occupied bandwidth 5 MHz channel, sample plot Figure 8.10-2: Occupied bandwidth 10 MHz channel, sample plot Report reference ID: 362902-1TRFWL-R1 Page 113 of 118

Section 8 Testing data Test name RSS-132 5.6 Receiver Spurious Emissions (B5) Specification RSS-132 and RSS-Gen, Issue 5 8.11 RSS-132 5.6 Receiver Spurious Emissions (B5) 8.11.1 Definitions and limits Receiver spurious emissions shall comply with the limits specified in RSS-Gen. RSS-Gen, 7.4: The antenna-conducted test shall be performed with the antenna disconnected and with the receiver antenna port connected to a measuring i nstrument having equal input impedance to that specified for the antenna. The RF cable connecting the receiver under test to the measuring instrument shall also have the same impedance to that specified for the receiver’s antenna. The spurious emissions from the receiver at any discrete frequency, measured at the antenna port by the antenna-conducted method, shall not exceed 2 nW in the frequency range 30-1000 MHz and 5 nW above 1 GHz. 8.11.2 Test summary Test date November 19, 2018 8.11.3 Observations, settings and special notes None 8.11.4 Test data Figure 8.11-1: Receiver spurious emissions below 1 GHz, antenna port A Figure 8.11-2: Receiver spurious emissions above 1 GHz, antenna port A Report reference ID: 362902-1TRFWL-R1 Page 114 of 118

Section 8 Testing data Test name RSS-132 5.6 Receiver Spurious Emissions (B5) Specification RSS-132 and RSS-Gen, Issue 5 Figure 8.11-3: Receiver spurious emissions below 1 GHz, antenna port B Figure 8.11-4: Receiver spurious emissions above 1 GHz, antenna port B Figure 8.11-5: Receiver spurious emissions below 1 GHz, antenna port C Figure 8.11-6: Receiver spurious emissions above 1 GHz, antenna port C Report reference ID: 362902-1TRFWL-R1 Page 115 of 118

Section 8 Testing data Test name RSS-132 5.6 Receiver Spurious Emissions (B5) Specification RSS-132 and RSS-Gen, Issue 5 Figure 8.11-7: Receiver spurious emissions below 1 GHz, antenna port D Figure 8.11-8: Receiver spurious emissions above 1 GHz, antenna port D Report reference ID: 362902-1TRFWL-R1 Page 116 of 118

Section 9 Section 9. Block diagrams of test set-ups Section 9. Block diagrams of test set-ups 9.1 Radiated emissions set-up for frequencies below 1 GHz Radio absorbing material Antenna mast Test antenna 4m 3m Test EUT antenna Non- conducting table 1m 0.8 m Metal ground plane Turn table Receiver 9.2 Radiated emissions set-up for frequencies above 1 GHz Radio absorbing material Antenna mast Test antenna 4m 3m EUT Test antenna Non- conducting table 1.5 m 1m Metal ground plane Turn table Receiver RF pre-amp Report reference ID: 362902-1TRFWL-R1 Page 117 of 118

Section 9 Section 9. Block diagrams of test set-ups 9.3 Antenna port set-up Antenna port EUT Receiver/Spectrum Analyzer ATT Report reference ID: 362902-1TRFWL-R1 Page 118 of 118


Document Created: 2018-12-07 09:51:11
Document Modified: 2018-12-07 09:51:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC