test report part 4

FCC ID: TA8AKRC161630-3

Test Report

Download: PDF
FCCID_3485270

Section 8 Testing data Test name FCC Part 2.1049 and RSS-Gen, 6.6 Occupied bandwidth Specification FCC Part 2, RSS-Gen, Issue 4 Figure 8.5-11: Occupied bandwidth, QPSK, 510 MHz, Port B, Mid channel Figure 8.5-12: Occupied bandwidth, QPSK, 10 MHz, Port B, High channel Figure 8.5-13: Occupied bandwidth, QPSK, 15 MHz, Port A, Low channel Figure 8.5-14: Occupied bandwidth, QPSK, 15 MHz, Port A, Mid channel Report reference ID: 334171-1TRFWL-R1 Page 96 of 103

Section 8 Testing data Test name FCC Part 2.1049 and RSS-Gen, 6.6 Occupied bandwidth Specification FCC Part 2, RSS-Gen, Issue 4 Figure 8.5-15: Occupied bandwidth, QPSK, 15 MHz, Port A, High channel Figure 8.5-16: Occupied bandwidth, QPSK, 15 MHz, Port B, Low channel Figure 8.5-17: Occupied bandwidth, QPSK, 15 MHz, Port B, Mid channel Figure 8.5-18: Occupied bandwidth, QPSK, 15 MHz, Port B, High channel Report reference ID: 334171-1TRFWL-R1 Page 97 of 103

Section 8 Testing data Test name FCC Part 2.1049 and RSS-Gen, 6.6 Occupied bandwidth Specification FCC Part 2, RSS-Gen, Issue 4 Figure 8.5-19: Occupied bandwidth, QPSK, 20 MHz, Port A, Low channel Figure 8.5-20: Occupied bandwidth, QPSK, 20 MHz, Port A, Mid channel Figure 8.5-21: Occupied bandwidth, QPSK, 20 MHz, Port A, High channel Figure 8.5-22: Occupied bandwidth, QPSK, 20 MHz, Port B, Low channel Report reference ID: 334171-1TRFWL-R1 Page 98 of 103

Section 8 Testing data Test name FCC Part 2.1049 and RSS-Gen, 6.6 Occupied bandwidth Specification FCC Part 2, RSS-Gen, Issue 4 Figure 8.5-23: Occupied bandwidth, QPSK, 20 MHz, Port B, Mid channel Figure 8.5-24: Occupied bandwidth, QPSK, 20 MHz, Port B, High channel Report reference ID: 334171-1TRFWL-R1 Page 99 of 103

Section 8 Testing data Test name RSS-Gen, 7.1.3 Receiver conducted limits Specification RSS-Gen, Issue 4 8.6 RSS-Gen, 7.1.3 Receiver conducted limits 8.6.1 Definitions and limits If the receiver has a detachable antenna of known impedance, an antenna-conducted spurious emissions measurement is permitted as an alternative to radiated measurement. However, the radiated method of Section 7.1.2 is preferred. The antenna-conducted test shall be performed with the antenna disconnected and with the receiver antenna terminals connected to a measuring instrument having equal impedance to that specified for the antenna. The receiver-spurious emissions measured at the antenna terminals by the antenna-conducted method shall then comply with the following limits: Receiver-spurious emissions at any discrete frequency shall not exceed 2 nW in the band 30–1000 MHz, nor 5 nW above 1000 MHz. 8.6.2 Test summary Test date July 13, 2017 Temperature 22 °C Test engineer Andrey Adelberg Air pressure 1009 mbar Verdict Pass Relative humidity 33 % 8.6.3 Observations, settings and special notes Spectrum analyzer settings: Detector mode Peak Resolution bandwidth 120 kHz (below 1 GHz), 1 MHz (above 1 GHz) Video bandwidth RBW × 3 Trace mode Max Hold 8.6.4 Test data Figure 8.6-1: Receiver spurious emissions at port A, below 1 GHz Figure 8.6-2: Receiver spurious emissions at Port B, below 1 GHz Report reference ID: 334171-1TRFWL-R1 Page 100 of 103

Section 8 Testing data Test name RSS-Gen, 7.1.3 Receiver conducted limits Specification RSS-Gen, Issue 4 Figure 8.6-3: Receiver spurious emissions at port A, above 1 GHz Figure 8.6-4: Receiver spurious emissions at Port B, above 1 GHz Report reference ID: 334171-1TRFWL-R1 Page 101 of 103

Section 9 Section 9. Block diagrams of test set-ups Section 9. Block diagrams of test set-ups 9.1 Radiated emissions set-up for frequencies below 1 GHz Radio absorbing material Antenna mast Test antenna 4m 3m Test EUT antenna Non- conducting table 1m 0.8 m Metal ground plane Turn table Receiver 9.2 Radiated emissions set-up for frequencies above 1 GHz Radio absorbing material Antenna mast Test antenna 4m 3m EUT Non- conducting Test table antenna 1m 1.5 m Metal ground plane Turn table Receiver Report reference ID: 334171-1TRFWL-R1 Page 102 of 103

Section 9 Section 9. Block diagrams of test set-ups 9.3 Conducted emissions set-up Environmental test chamber EUT Receiver DC power supply Attenuator Report reference ID: 334171-1TRFWL-R1 Page 103 of 103


Document Created: 2017-07-27 11:53:17
Document Modified: 2017-07-27 11:53:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC