RF Exposure Information

FCC ID: T8H-BESTPM104

RF Exposure Info

Download: PDF
FCCID_4439372

TEST REPORT Report Number: 103769042MPK-001B Project Number: G103769042 January 10, 2019 Testing performed on the PKP reader Model: PKP FCC ID: T8H-BESTPM104 IC: 7713A-BESTPM104 to FCC Part 15 Subpart C (15.209) FCC Part 15 Subpart C (15.207) RSS-210 Issue 9 FCC Part 15, Subpart B Industry Canada ICES-003 For Dormakaba USA, Inc. Test Performed by: Test Authorized by: Intertek Dormakaba USA, Inc. 1365 Adams Court 6161 E. 75th Street. Menlo Park, CA 94025 USA Indianapolis, IN 46250 Prepared by: Date: January 10, 2019 Minh Ly Reviewed by: Date: January 10, 2019 Krishna Vemuri This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. This report must not be used to claim product endorsement by A2LA, NIST nor any other agency of the U.S. Government. EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 1 of 22

Report No. 103769042MPK-001B Equipment Under Test: PKP reader Trade Name: Dormakaba USA, Inc. Model Number: PKP Serial Number: MPK1812101554-004 (PKP Module) Applicant: Dormakaba USA, Inc. Contact: E.J. Caylor Dormakaba USA, Inc. Address: 6161 E. 75th Street. Indianapolis, IN 46250 Country: USA Tel. Number: (317) 806-3501 Email: Ej.caylor@dormakaba.com FCC Part 15 Subpart C (15.209) FCC Part 15 Subpart C (15.207) Applicable Regulation: RSS-210 Issue 9 FCC Part 15, Subpart B Industry Canada ICES-003 Issue 6 ITS – Site 1 Test Site Location: 1365 Adams Drive Menlo Park, CA 94025 Date(s) of Test: December 10 to January 04, 2019 We attest to the accuracy of this report: Minh Ly Krishna K Vemuri EMC Project Engineer Engineering Team Lead EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 2 of 22

TABLE OF CONTENTS 1.0 Summary of Tests .......................................................................................................................... 4 2.0 General Description ....................................................................................................................... 5 2.1 Product Description ............................................................................................................ 5 2.2 Related Submittal(s) Grants ................................................................................................ 6 2.3 Test Methodology ............................................................................................................... 6 2.4 Test Facility ........................................................................................................................ 6 3.0 System Test Configuration ............................................................................................................ 7 3.1 Support Equipment and description .................................................................................... 7 3.2 Block Diagram of Test Setup.............................................................................................. 7 3.3 Justification ......................................................................................................................... 8 3.4 Software Exercise Program................................................................................................. 8 3.5 Mode of Operation during test ............................................................................................ 8 3.6 Modifications required for Compliance .............................................................................. 8 3.7 Additions, deviations and exclusions from standards ......................................................... 8 4.0 Measurement Results..................................................................................................................... 9 4.1 Field Strength of Fundamental and Radiated Emissions Outside the band ........................ 9 4.2 AC Line Conducted Emission .......................................................................................... 15 4.3 Occupied Bandwidth......................................................................................................... 19 5.0 List of test equipment .................................................................................................................. 21 6.0 Document History ........................................................................................................................ 22 EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 3 of 22

1.0 Summary of Tests REFERENCE FCC REFERENCE RSS- TEST RESULTS 15.225 210 Radiated Transmitter RSS-GEN 15.209 Complies Emissions Line Conducted RSS-GEN 15.207 Complies Emissions Radiated Emission from Digital Part and 15.109 ICES 003 Complies Receiver AC Line Conducted ICES 003 15.107 Complies Emission Occupied Bandwidth - RSS-GEN Complies Antenna Requirement 15.203 RSS-GEN Complies1 1 EUT utilizes an internal Antenna. EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 4 of 22

2.0 General Description 2.1 Product Description Dormakaba USA, Inc. supplied the following description of the EUT: The PKP is a 125kHz low power RFID card reader. For more information, refer to the following product specification, declared by the manufacturer. Overview of the EUT Dormakaba USA, Inc. Applicant name & 6161 E. 75th Street. address: Indianapolis, IN 46250 Contact info / Email: E.J. Caylor / Ej.caylor@dormakaba.com Model: PKP FCC Identifier: T8H-BESTPM104 IC Identifier: 7713A-BESTPM104 Operating Frequency: Single frequency, 125 kHz Number of Channels: 1 Type of Modulation: CW Antenna Type: Internal Antenna EUT receive date: December 10, 2018 EUT receive condition: The EUT was received in good condition with no apparent damage. As declared by the Applicant it is identical to the production units. Test start date: December 10, 2018 Test completion date: January 04, 2019 EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 5 of 22

2.2 Related Submittal(s) Grants None 2.3 Test Methodology Both AC mains line-conducted and radiated emissions measurements were performed according to the procedures in ANSI C63.4: 2014. Radiated tests were performed at an antenna to EUT distance of 10 meters, unless stated otherwise in this test report. All other measurements were made in accordance with the procedures in part 2 of CFR 47, ANSI C63.10: 2013 & RSS-GEN Issue 5. 2.4 Test Facility The radiated emission test site and conducted measurement facility used to collect the data is 10m semi- anechoic chamber located in Menlo Park, California. This test facility and site measurement data have been fully placed on file with the FCC and Industry Canada (Site # 2042L-1). EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 6 of 22

3.0 System Test Configuration 3.1 Support Equipment and description Support Equipment Type Model # Quantity S/N DC Power Supply Extech 1 D30030012 3.2 Block Diagram of Test Setup The diagram shown below details the interconnection of the EUT and support equipment. For specific layout, refer to the test configuration photograph in the relevant section of this report. PKP MODULE Only EUT DC Power 120VAC Supply 60Hz S = Shielded F = With Ferrite U = Unshielded m = Length in Meters EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 7 of 22

3.3 Justification The EUT was configured to continuously transmit and looking for tags. This report covers the RFID radio only. For radiated emission measurements the EUT is placed on a non-conductive table. The highest clock frequency used is 8 MHz, as specified by Dormakaba USA, Inc., so radiated emissions were performed up to 1 GHz for the module. This report was generated from Intertek report number: 103769042MPK-001 with the data for the PKP module only. 3.4 Software Exercise Program EUT was programmed to continuously transmit and read tags. 3.5 Mode of Operation during test EUT was continuously transmitting during the tests. 3.6 Modifications required for Compliance No modifications were installed by Intertek Testing Services during compliance testing in order to bring the product into compliance. 3.7 Additions, deviations and exclusions from standards No additions, deviations or exclusion have been made from standard. EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 8 of 22

4.0 Measurement Results 4.1 Field Strength of Fundamental and Radiated Emissions Outside the band 4.1.1 Requirements §15.209 Radiated emission limits; general requirements. Frequency Field strength Measurement distance (MHz) (microvolts/meter) (meters) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 Limits for Electromagnetic Radiated Disturbance, FCC Section 15.109(b) Frequency Class A at 10m Class B at 3m (MHz) dB(µV/m) dB(µV/m) 30-88 39.0 40.0 88-216 43.5 43.5 216-960 46.4 46.0 Above 960 49.5 54.0 Note: Three sets of units are commonly used for EMI measurement, decibels below one milliwatt (-dBm), decibels above a microvolt (dBµV), and microvolts (µV). To convert between them, use the following formulas: 20 LOG10 (µV) = dBµV, dBm = dBµV-107 EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 9 of 22

4.1.2 Procedure Radiated Measurements Below 30 MHz During the test the EUT is rotated and the measuring antenna angles are varied during the search for maximum signal level. Radiated emissions are taken at ten meters unless the signal level is too low for measurement at that distance. If necessary, a pre-amplifier is used and/or the test is conducted at a closer distance. Measurements for below 30 MHz were made at 10 meters. Data results below are corrected for distance back to 30 meters. Radiated Measurements Above 30 MHz During the test the EUT is rotated and the measuring antenna height and polarization are varied during the search for maximum signal level. The antenna height is varied from 1 to 4 meters. Radiated emissions are taken at ten meters unless the signal level is too low for measurement at that distance. If necessary, a pre-amplifier is used and/or the test is conducted at a closer distance. Measurements for above 30 MHz were made at 10 meters. Radiated emission measurements were performed from 9kHz to 1 GHz. Analyzer resolution is: 200Hz or greater for 9kHz to 150kHz 9 kHz or greater for 150kHz to 30 MHz 120 kHz or greater for 30MHz to 1000 MHz For those frequencies quasi-peak detector applies Data includes of the worst-case configuration (the configuration which resulted in the highest emission levels). A sample calculation, configuration photographs and data tables of the emissions are included. Field Strength Calculation The field strength is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain (if any) from the measured reading. The basic equation is as follows: FS = RA + AF + CF – AG – DCF Where FS = Field Strength in dB (µV/m) RA = Receiver Amplitude (including preamplifier) in dB (µV) CF = Cable Attenuation Factor in dB AF = Antenna Factor in dB (1/m) AG = Amplifier Gain in dB DCF = Distance Correction Factor Note: FS was measured with loop antenna below 30MHz EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 10 of 22

4.1.3 Test Result Test date: December 13, 2018 to January 04, 2019 The data below shows the significant emission frequencies, the limit and the margin of compliance. Note: Measurements were performed at parallel and perpendicular orientation of loop antenna, and vertical and horizontal orientations of EUT. 15.209 Radiated Spurious Emissions from 9 kHz to 30MHz (PKP Module) FCC Part 15/FCC 15.209, 9kHz - 30MHz at 10m - QPeak/10.0m/ Meas.Peak (Horizontal) Meas.Peak (Vertical) Peak (Peak /Lim. QPeak ) (Horizontal) Peak (Peak /Lim. QPeak ) (Vertical) 115 dBµV/m 100 80 60 40 20 5 9kHz 100k 1M 10M 30MHz Frequency Model: ; Client: ; Comments: ; Test Date: 12/13/2018 16:51 Frequency Peak @10m QP-Limit@10m Margin Angle Antenna Correction (MHz) dB(µV/m) dB(µV/m) (dB) (°) Orientation (dB) 0.125 45.5 84.76 -39.3 11.5 Parallel 31.9 0.125 43.2 84.76 -41.6 80.0 Perpendicular 31.9 EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 11 of 22

15.109 Class B & 15.209 Radiated Spurious Emissions from 30 MHz to 1000 MHz (PKP Module) FCC Part 15/FCC Part 15.109 30M-40GHz B - QPeak/10.0m/ Meas.Peak (Horizontal) Meas.Peak (Vertical) Peak (Peak /Lim. QPeak ) (Horizontal) Peak (Peak /Lim. QPeak ) (Vertical) 70 dBµV/m 60 50 40 30 20 10 0 30MHz 100M 1GHz Frequency Model: ; Client: ; Comments: ; Test Date: 12/14/2018 18:26 Frequency QPeak@10m Lim. QPeak Margin Angle Height Antenna Correction (MHz) dB(µV/m) dB(µV/m) (dB) (°) (m) Polarization (dB) 30.485 21.7 29.5 -7.8 207.3 4.0 Horizontal -9.7 57.516 16.4 29.5 -13.1 275.8 4.0 Horizontal -15.6 801.829 27.4 35.5 -8.1 163.5 1.0 Horizontal -3.1 57.419 19.2 29.5 -10.4 200.3 4.0 Vertical -15.6 60.620 18.0 29.5 -11.5 326.5 4.0 Vertical -16.7 801.829 26.6 35.5 -8.9 54.3 2.0 Vertical -3.1 Results Complies EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 12 of 22

4.1.4 Test Configuration Photographs The following photographs show the testing configurations used. PKP MODULE EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 13 of 22

4.1.4 Test Configuration Photographs (Continued) PKP MODULE EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 14 of 22

4.2 AC Line Conducted Emission FCC Rule 15.107/15.207 4.2.1 Requirement Frequency Band Class B Limit dB(µV) Class A Limit dB(µV) MHz Quasi-Peak Average Quasi-Peak Average 0.15-0.50 66 to 56 * 56 to 46 * 79 66 0.50-5.00 56 46 73 60 5.00-30.00 60 50 73 60 Note: *Decreases linearly with the logarithm of the frequency. At the transition frequency the lower limit applies. 4.2.2 Procedure Measurements are carried out using quasi-peak and average detector receivers in accordance with CISPR 16. An AMN is required to provide a defined impedance at high frequencies across the power feed at the point of measurement of terminal voltage and also to provide isolation of the circuit under test from the ambient noise on the power lines. An AMN as defined in CISPR 16 shall be used. The EUT is located so that the distance between the boundary of the EUT and the closest surface of the AMN is 0.8m. Where a flexible mains cord is provided by the manufacturer, this shall be 1m long or if in excess of 1m, the excess cable is folded back and forth as far as possible so as to form a bundle not exceeding 0.4m in length. The EUT is arranged and connected with cables terminated in accordance with the product specification. Conducted disturbance is measured between the phase lead and the reference ground, and between the neutral lead and the reference ground. Both measured values are reported. The EUT, where intended for tabletop use, is placed on a table whose top is 0.8m above the ground plane. A vertical, metal reference plane is placed 0.4m from the EUT. The vertical metal reference-plane is at least 2m by 2m. The EUT shall be kept at least 0.8m from any other metal surface or other ground plane not being part of the EUT. The table is constructed of non-conductive materials. Its dimensions are 1m by 1.5m but may be extended for larger EUT. Floor standing EUT are placed on a horizontal metal ground plane and isolated from the ground plane by resting on an insulating material. The metal ground plane extends at least 0.5m beyond the boundaries of the EUT and has minimum dimensions of 2m by 2m. EUT was placed in transmission mode then tested for conducted emissions per 15.207 and 15.107. Test date: December 19, 2018 EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 15 of 22

4.2.3 Test Result 15.107 Class B & 15.207 AC Line Conducted Emission from 150kMHz to 30 MHz Phase 1 Sub-range 1 FCC Part 15/FCC Part 15.107 B - Average/ Frequencies: 150 kHz - 30 MHz (Mode: - Step: 2.25 kHz ) FCC Part 15/FCC Part 15.107 B - QPeak/ Settings: RBW: 9kHz, VBW: 30kHz, Sweep time: 1e+03 ms, Attenuation: 10 dB, Sweep count 3, Preamp: Off, LN Preamp: Meas.QPeak (PhaseOff, 1) Preselector: On Line:Phase 1 Mes. CISPR AVG (Phase 1) QPeak (QPeak /Lim. QPeak ) (Phase 1) CISPR AVG (CISPR AVG /Lim. Average ) (Phase 1) 110 dBµV 100 90 80 70 60 50 40 30 20 10 0 150kHz 1M 10M 30MHz Frequency Line: Phase 1 Model: ; Client: ; Comments: ; Test Date: 12/19/2018 16:50 Phase 2 Sub-range 2 FCC Part 15/FCC Part 15.107 B - Average/ Frequencies: 150 kHz - 30 MHz (Mode: - Step: 2.25 kHz ) FCC Part 15/FCC Part 15.107 B - QPeak/ Settings: RBW: 9kHz, VBW: 30kHz, Sweep time: 1e+03 ms, Attenuation: 10 dB, Sweep count 1, Preamp: Off, LN Preamp: Meas.QPeak (PhaseOff, 2) Preselector: On Line:Phase 2 Mes. CISPR AVG (Phase 2) QPeak (QPeak /Lim. QPeak ) (Phase 2) CISPR AVG (CISPR AVG /Lim. Average ) (Phase 2) 110 dBµV 100 90 80 70 60 50 40 30 20 10 0 150kHz 1M 10M 30MHz Frequency Line: Phase 2 Model: ; Client: ; Comments: ; Test Date: 12/19/2018 16:50 EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 16 of 22

Quasi Peak Table Frequency QPeak Lim. QPeak QPeak-Lim Correction Phase (MHz) (dBµV) (dBµV) (dB) (dB) 0.2 2.0 31.4 65.9 -34.5 Phase 2 0.2 1.0 31.3 65.9 -34.6 Phase 1 0.5 1.0 10.3 56.0 -45.7 Phase 1 0.6 2.0 10.3 56.0 -45.7 Phase 2 24.0 2.0 12.0 60.0 -48.0 Phase 2 24.0 1.0 11.5 60.0 -48.5 Phase 1 Average Table Frequency AVG Lim. Average AVG-Lim Correction Phase (MHz) (dBµV) (dBµV) (dB) (dB) 0.2 2.0 10.2 56.0 -45.8 Phase 2 0.2 1.0 10.2 56.0 -45.8 Phase 1 4.8 2.0 6.7 46.0 -39.3 Phase 2 5.0 1.0 6.8 46.0 -39.3 Phase 1 24.0 2.0 10.0 50.0 -40.0 Phase 2 29.9 1.0 9.8 50.0 -40.2 Phase 1 Results Complies EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 17 of 22

4.2.4 Test Configuration Photographs The following photographs show the testing configurations used. EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 18 of 22

4.3 Occupied Bandwidth RSS-GEN 4.3.1 Requirements The the occupied bandwidth or the “99% emission bandwidth” is defined as the frequency range between two points, one above and the other below the carrier frequency, within which 99% of the total transmitted power of the fundamental transmitted emission is contained. The occupied bandwidth shall be reported for all equipment in addition to the specified bandwidth required in the applicable RSS. For the 99% emission bandwidth, the trace data points are recovered and directly summed in linear power level terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5% of the total is reached, and that frequency recorded. The process is repeated for the highest frequency data points (starting at the highest frequency, at the right side of the span, and going down in frequency). This frequency is then recorded. The difference between the two recorded frequencies is the occupied bandwidth (or the 99% emission bandwidth). 4.3.2 Procedure The EUT was setup to transmit in normal operating condition. Measurements were made with the loop antenna in close proximity of the EUT. Following the procedures of ANSI 63.10, the 99% bandwidth measurements were taken. The Spectrum Analyzers 99% BW measurement function were used to measure the 99% Bandwidth. The following plots show Occupied Bandwidth. Test date: December 20, 2018 EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 19 of 22

4.3.3 Test Results Frequency 99% Channel Bandwidth (kHz) (kHz) 125 8.54 kHz EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 20 of 22

5.0 List of test equipment Measurement equipment used for emission compliance testing utilized the equipment on the following list: Calibration Equipment Manufacturer Model/Type Asset No. Cal Due Interval Loop Antenna EMCO 6512 ITS 01598 12 10/09/19 Sonoma Pre-Amplifier 310 ITS 01493 12 10/20/18 Instrument Rohde and EMI Receiver ESR7 ITS 01607 12 10/23/19 Schwarz BI-Log Antenna Antenna Research LPB-2513 ITS 00355 12 02/21/19 LISN Com Power LIN-115A ITS 01283 12 10/03/19 Loop Sensor Solar Electronics 7334-1 ITS 01608 12 10/09/19 * Calibration performed by ITS prior to the test. # Calibration not required Software used for emission compliance testing utilized the following: Name Manufacturer Version Template/Profile BAT-EMC Nexio 3.16.0.64 Dormakaba_PKP EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 21 of 22

6.0 Document History Revision/ Writer Reviewer Date Change Job Number Initials Initials 1.0 / G103769042 ML KV January 10, 2019 Original document END OF REPORT EMC Report for Dormakaba USA, Inc. on the PKP reader File: 103769042MPK-001B Page 22 of 22


Document Created: 2019-08-28 10:17:12
Document Modified: 2019-08-28 10:17:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC