Test Report_JBP Revised

FCC ID: SZGCECHYA0091

Test Report

Download: PDF
FCCID_3118091

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 FCC TEST REPORT According to 47 CFR, Part 2, Part 15B, CISPR PUB. 22 Applicant : Weifang GoerTek Electronic Co.,LTD Gaoxin 2 Road,Free Trade Zone,Weifang, Address : Shandong,261205,P.R.China Wireless Stereo Headset Equipment : Wireless Adaptor CECHYA-0090; Model No. : CECHYA-0091 Brand name : Sony Interactive Entertainment America LLC SZGCECHYA0090 (Headset) FCC ID : SZGCECHYA0091 (Adaptor) I HEREBY CERTIFY THAT : The sample was received on Jul 12, 2016 and the testing was carried out on Jul 21, 2016 at Cerpass Technology Corp. The test result refers exclusively to the test presented test model / sample. Without written approval of Cerpass Technology Corp., the test report shall not be reproduced except in full. Approved by: Ray Chou EMC/RF B.U. Assistant Manager Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 1 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 FCC TEST REPORT Issued by: Cerpass Technology Co.,Ltd No.10, Lane 2, Lianfu Street, Luzhu Township, Taoyuan County 33848, Taiwan(R.O.C.) Tel: 886-3-322-6888 Fax: 886-3-322-6881 The test record, data evaluation & Equipment. Under Test configurations represented herein are true and accurate accounts of the measurements of the samples EMC characteristics under the conditions specified in this report. Laboratory Accreditation: Cerpass Technology Corporation Test Laboratory NVLAP LAB Code: 200954-0 TAF LAB Code: 1439 Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 2 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Contents 1. Summary of Test Procedure and Test Result........................................................................................... 5 1.1. Applicable Standards ....................................................................................................................... 5 2. Test Configuration of Equipment under Test ........................................................................................... 6 2.1. Feature of Equipment under Test..................................................................................................... 6 2.2. Test Manner ..................................................................................................................................... 7 2.3. Description of Support Unit .............................................................................................................. 7 2.4. Connection Diagram of Test System................................................................................................ 8 2.5. General Information of Test............................................................................................................ 11 2.6. Measurement Uncertainty .............................................................................................................. 11 3. Test of Conducted Emission.................................................................................................................... 12 3.1. Test Limit ........................................................................................................................................ 12 3.2. Test Procedures ............................................................................................................................. 12 3.3. Typical test Setup........................................................................................................................... 13 3.4. Measurement Equipment ............................................................................................................... 13 3.5. Test Result and Data...................................................................................................................... 14 4. Test of Radiated Emission ....................................................................................................................... 15 4.1. Test Limit ........................................................................................................................................ 15 4.2. Test Procedures ............................................................................................................................. 16 4.3. Typical test Setup........................................................................................................................... 17 4.4. Measurement Equipment ............................................................................................................... 18 4.5. Test Result and Data (30MHz~1GHz)............................................................................................ 19 4.6. Test Result and Data (1GHz ~ 18GHz).......................................................................................... 25 Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 3 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 History of this test report  ORIGINAL.  Additional attachment as following record: Report No Version Date Description SEFD1605172 Rev 01 Aug 01, 2016 Initial Issue Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 4 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 1. Summary of Test Procedure and Test Result 1.1. Applicable Standards The measurements shown in this test report were made in accordance with the procedures given in ANSI C63.4 – 2014 and the energy emitted by this equipment was passed Part 2, Part 15, CISPR PUB. 22. The energy emitted by this equipment was passed both Radiated and Conducted Emissions Class B limits. Test Item Normative References Test Result Remarks ANSI C63.4-2014 Conducted Emission N/A N/A FCC Part 15 Subpart B Meets Class B Limit ANSI C63.4-2014 Minimum passing Radiated Emission PASS FCC Part 15 Subpart B margin(Peak) is-12.63dB at 947.6200MHz Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 5 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 2. Test Configuration of Equipment under Test 2.1. Feature of Equipment under Test Wireless Stereo Headset CECHYA-0090; Model No.: Wireless Adaptor CECHYA-0091 U+Dongle Model No.: PVT1-1.0-219 Audio Cable Non-Shielded,1.2m USB Cable Shielded, 0.7m, with one ferrites core bonded Note: Please refer to user manual. Model Discrepancy: Discrepancy Equipment Wireless Stereo Headset Wireless Adaptor Model No. CECHYA-0090 CECHYA-0091 Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 6 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 2.2. Test Manner a. During testing, the interface cables and equipment positions were varied according to ANSI C63.4. b. The complete test system included Notebook PC and EUT for EMI test. c. During the test, setup up the EUT and all system, turn on the power of all Equipments. d. Make the EUT at the test mode and it is normal operation, and then test. The pre-test modes : Mode 1: Charging Mode(From Computer) Mode 2: Normal Communication Mode(By Audio cable) Mode 3: Wierless Communication Mode(By U+Dongle) The final modes : Mode 1: Charging Mode(From Computer) Mode 2: Normal Communication Mode(By Audio cable) Mode 3: Wierless Communication Mode(By U+Dongle) 2.3. Description of Support Unit No. Device Manufacturer Model No. Description 1 Notebook PC DELL Vostro 3560 R31199 Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 7 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 2.4. Connection Diagram of Test System Mode 1 No. Cable Quantity Description A USB Cable 1 Shielded, 0.7m with one ferrites core bonded Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 8 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Mode 2 No. Cable Quantity Description A Audio Cable 1 Non-Shielded, 1.2m Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 9 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Mode 3 No. Cable Quantity Description N/A N/A N/A N/A Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 10 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 2.5. General Information of Test Test Site : Cerpass Technology Corporation Test Laboratory Address: No.10, Ln. 2, Lianfu St., Luzhu Dist., Taoyuan City 33848, Taiwan (R.O.C.) Tel:+886-3-3226-888 Fax:+886-3-3226-881 Address: No.68-1, Shihbachongsi, Shihding Township, New Taipei City 223, Taiwan, R.O.C. Tel: +886-2-2663-8582 FCC Registration Number : TW1079, TW1061,390316, 228391, 641184 IC Registration Number : 4934B-1, 4934E-1, 4934E-2 T-2205 for Telecommunication Test C-4663 for Conducted emission test VCCI R-3428, R-4218 for Radiated emission test G-812, G-813 for radiated disturbance above 1GHz Frequency Range Conducted Emission Test: from 150 kHz to 30 MHz Investigated : Radiated Emission Test: from 30 MHz to 18,000 MHz The test distance of radiated emission below 1GHz from antenna to EUT is 3 M. Test Distance : The test distance of radiated emission above 1GHz from antenna to EUT is 3 M. 2.6. Measurement Uncertainty Measurement Item Measurement Frequency Polarization Uncertainty Conducted Emission 9 kHz ~ 30 MHz LINE / NEUTRAL 3.25 dB 30 MHz ~ 1,000 MHz Vertical / Horizontal 3.93 dB Radiated Emission 1,000 MHz ~ 18,000 MHz Vertical / Horizontal 5.18 dB The measurement uncertainty will be considered, when test result margin to the limit. Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 11 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 3. Test of Conducted Emission 3.1. Test Limit Conducted Emissions were measured from 150 kHz to 30 MHz with a bandwidth of 9 KHz on the 120 VAC power and return leads of the EUT according to the methods defined in ANSI C63.4-2009 Section 3.1. The EUT was placed on a nonmetallic stand in a shielded room 0.8 meters above the ground plane as shown in section 2.2. The interface cables and equipment positioning were varied within limits of reasonable applications to determine the position produced maximum conducted emissions. Conducted Emission Limits: Frequency Quasi Peak Average (MHz) (dB µ V) (dB µ V) 0.15 – 0.5 66-56* 56-46* 0.5 – 5.0 56 46 5.0 – 30.0 60 50 3.2. Test Procedures a. The EUT was placed 0.4 meter from the conducting wall of the shielding room was kept at least 80 centimeters from any other grounded conducting surface. b. Connect EUT to the power mains through a line impedance stabilization network (LISN). c. All the support units are connecting to the other LISN. d. The LISN provides 50 ohm coupling impedance for the measuring instrument. e. The FCC states that a 50 ohm, 50 micro-Henry LISN should be used. f. Both sides of AC line were checked for maximum conducted interference. g. The frequency range from 150 kHz to 30 MHz was searched. h. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 12 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 3.3. Typical test Setup 10cm EUT 80cm 80cm 80cm 40cm LISN LISN 40cm 3.4. Measurement Equipment Calibration Instrument/Ancillary Manufacturer Model No. Serial No. Valid Date. Date Test Receiver R&S ESCI 100565 2016.03.26 2017.03.25 AMN R&S ESH2-Z5 100182 2015.09.06 2016.09.05 Two-Line V-Network R&S ENV216 100325 / / ISN FCC FCC-TLISN-T2-02 20379 2016.03.26 2017.03.25 ISN FCC FCC-TLISN-T4-02 20380 2016.03.26 2017.03.25 ISN FCC FCC-TLISN-T8-02 20381 2016.03.26 2017.03.25 ISN TESEQ ISN ST08 30175 2016.03.26 2017.03.25 Current Probe R&S EZ-17 100303 2016.03.26 2017.03.25 Passive Voltage Probe R&S ESH2-Z3 100026 2016.03.26 2017.03.25 Pulse Limiter R&S ESH3-Z2 100529 2016.03.26 2017.03.25 Temperature/ Humidity Zhicheng ZC1-11 CEP-TH-004 2016.03.29 2017.03.28 Meter EZ-EMC Fala Ver CT3A1 N/A N/A N/A Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 13 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 3.5. Test Result and Data For this product is supplied by DC source, this test item needn't perform. Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 14 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 4. Test of Radiated Emission 4.1. Test Limit Below 1GHz (for digital device) For unintentional device, according to CISPR PUB.22, for Class B digital devices, the general requirement of field strength of radiated emissions from intentional radiators at a distance of 10 meters shall not exceed the below table. dBuV/m (At 10m) FREQUENCY (MHz) Class A Class B 30 ~ 230 40 30 230 ~ 1000 47 37 Limit tables for non-digital device: Class A Radiated Emission limit at 10m (for others) Frequency Field Strength Limit Field Strength Limit (MHZ) (uV/m)Q.P. (dBuV/m)Q.P. 30 - 88 90 39 88 - 216 150 43.5 216 – 960 210 46.4 Above 960 300 49.5 Class B Radiated Emission limit at 3m (for others) Frequency Field Strength Limit Field Strength Limit (MHZ) (uV/m)Q.P. (dBuV/m)Q.P. 30 - 88 100 40 88 - 216 150 43.5 216 – 960 200 46 Above 960 500 54 Above 1GHz(for all device) Class A (dBuV/m) (At 10m) Class B (dBuV/m) (At 3m) Frequency (MHZ) Average Peak Average Peak Above 1000 49.5 69.5 54 74 NOTE: (1) The lower limit shall apply at the transition frequencies. (2) Emission level (dBuV/m) = 20 log Emission level (uV/m). (3) The measurement above 1GHz is at close-in distances 3m,and determine the limit L2 corresponding to the close-in distance d2 by applying the following relation: L2 = L1 (d1/d2), where L1 is the specified limit in microvolts per metre (uV/m) at the distance d1 (10m), L2 is the new limit for distance d2 (3m). So the new Class A limit above 1GHz at 3m is as following table: Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 15 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Class A (dBuV/m) (At 3m) Frequency (MHZ) Average Peak Above 1000 60 80 According to FCC Part 15.33 (b), for an unintentional radiator, including a digital device, the spectrum shall be investigated from the lowest radio frequency signal generated or used in the device, without going below the lowest frequency for which a radiated emission limit is specified, up to the frequency shown in the following table: Highest frequency generated or used in the Upper frequency of measurement range device or on which the device operates or tunes (MHz) (MHz) Below 1.75 30 1.75-108 1000 108-500 2000 500-1000 5000 5th harmonic of the highest frequency or 40GHz, Above 1000 whichever is lower 4.2. Test Procedures Procedure of Preliminary Test  The equipment was set up as per the test configuration to simulate typical usage per the user’s manual. When the EUT is a tabletop system, a wooden turntable with a height of 0.8 meters is used which is placed on the ground plane. When the EUT is a floor standing equipment, it is placed on the ground plane which has a 15 cm non-conductive covering to insulate the EUT from the ground plane.  Support equipment, if needed, was placed as per ANSI C63.4.  All I/O cables were positioned to simulate typical usage as per ANSI C63.4.  The EUT received AC 120VAC/60Hz power source from the outlet socket under the turntable. All support equipment power received from another socket under the turntable.  The antenna was placed at 3 or 10 meter away from the EUT as stated in ANSI C63.4. The antenna connected to the Spectrum Analyzer via a cable and at times a pre-amplifier would be used.  The Analyzer / Receiver quickly scanned from 30MHz to 40GHz. The EUT test program was started. Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level. Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 16 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172  Set the spectrum analyzer/ Receiver in the following setting as: Below 1GHz: RBW=120KHz / VBW=300KHz / Sweep=AUTO Above 1GHz: Peak: RBW=1MHz, VBW=3MHz / Sweep=AUTO Average: RBW=1MHz / VBW=1Hz / Sweep=AUTO  The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test. Procedure of Final Test  EUT and support equipment were set up on the turntable as per the configuration with highest emission level in the preliminary test.  The Analyzer / Receiver scanned from 30MHz to 40GHz. Emissions were scanned and measured rotating the EUT to 360 degrees, varying cable placement and positioning the antenna 1 or 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level.  Recording at least the six highest emissions. Emission frequency, amplitude, antenna position, polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. Below 1GHz the Q.P. reading and above 1GHz the Peak and Average reading are presented.  The test data of the worst-case condition(s) was recorded. 4.3. Typical test Setup Below 1GHz Test Setup Antenna Equipment under Test * 3m 0.8M Turn Ground Plane Receiver Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 17 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Above 1GHz Test Setup 4.4. Measurement Equipment Calibration Instrument/Ancillary Manufacturer Model No. Serial No. Valid Date. Date EMI Test Receiver R&S ESCI 101183 2016.03.26 2017.03.25 Preamplifier songyi EM330 60618 2016.03.26 2017.03.25 Preamplifier Agilent 8449B 3008A02342 2016.03.26 2017.03.25 Bilog Antenna Sunol Science JB1 A072414-1 2016.04.16 2017.04.15 Broad-Band Horn Schwarzbeck BBHA9120D 9120D-618 2016.04.16 2017.04.15 Antenna Broad-Band Horn Schwarzbeck BBHA9170 9170-347 2016.04.16 2017.04.15 Antenna Preamplifier COM-POWER PA-840 711885 2016.03.26 2017.03.25 Spectrum Analyzer R&S FSP40 100324 2016.03.26 2017.03.25 Temperature/ Humidity Zhicheng ZC1-11 CEP-TH-002 2016.03.29 2017.03.28 Meter EZ-EMC Fala Ver CT3A1 N/A N/A N/A Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 18 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 4.5. Test Result and Data (30MHz~1GHz) Test Mode : Mode 1: Charging Mode(From Computer) DC Power : DC 3.7V Ant. Polarization: Horizontal Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 30.9699 -2.85 28.90 26.05 40.00 -13.95 peak 100 248 2 128.9399 -8.93 34.05 25.12 43.50 -18.38 peak 200 136 3 157.0699 -7.53 34.20 26.67 43.50 -16.83 peak 100 138 4 323.9100 -6.31 33.55 27.24 46.00 -18.76 peak 100 268 5 511.1200 -4.63 32.03 27.40 46.00 -18.60 peak 100 60 6 738.1000 1.62 29.06 30.68 46.00 -15.32 peak 100 241 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 19 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 1: Charging Mode(From Computer) DC Power : DC 3.7V Ant. Polarization: Vertical Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 30.9699 -2.85 28.78 25.93 40.00 -14.07 peak 184 0 2 102.7500 -12.38 34.77 22.39 43.50 -21.11 peak 100 105 3 157.0699 -7.53 34.34 26.81 43.50 -16.69 peak 200 356 4 432.5500 -4.61 29.09 24.48 46.00 -21.52 peak 200 38 5 704.1499 1.18 29.48 30.66 46.00 -15.34 peak 141 0 6 947.6200 2.53 30.84 33.37 46.00 -12.63 peak 100 209 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 20 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 2: Normal Communication Mode(By Audio cable) DC Power : DC 3.7V Ant. Polarization: Horizontal Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 99.8399 -12.83 38.90 26.07 43.50 -17.43 peak 200 129 2 128.9398 -8.93 34.05 25.12 43.50 -18.38 peak 200 136 3 157.0699 -7.53 32.20 24.67 43.50 -18.83 peak 100 138 4 284.1399 -8.84 34.50 25.66 46.00 -20.34 peak 100 215 5 361.7400 -6.86 32.53 25.67 46.00 -20.33 peak 100 206 6 715.7898 1.33 29.28 30.61 46.00 -15.39 peak 200 169 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 21 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 2: Normal Communication Mode(By Audio cable) DC Power : DC 3.7V Ant. Polarization: Vertical Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 122.1500 -9.61 36.86 27.25 43.50 -16.25 peak 100 200 2 157.0699 -7.53 35.84 28.31 43.50 -15.19 peak 200 356 3 176.4698 -7.63 36.71 29.08 43.50 -14.42 peak 100 101 4 556.7100 -3.42 32.62 29.20 46.00 -16.80 peak 100 319 5 704.1499 1.18 29.48 30.66 46.00 -15.34 peak 141 0 6 748.7698 1.42 29.35 30.77 46.00 -15.23 peak 200 33 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 22 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 3: Wireless Communication Mode(By U+Dongle) DC Power : DC 3.7V Ant. Polarization: Horizontal Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 128.9398 -8.93 36.05 27.12 43.50 -16.38 peak 200 136 2 167.7400 -7.55 36.89 29.34 43.50 -14.16 peak 100 209 3 323.9100 -6.31 33.55 27.24 46.00 -18.76 peak 100 268 4 421.8799 -3.48 31.86 28.38 46.00 -17.62 peak 100 2 5 511.1200 -4.63 34.03 29.40 46.00 -16.60 peak 100 60 6 712.8799 1.29 28.96 30.25 46.00 -15.75 peak 100 241 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 23 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 3: Wireless Communication Mode(By U+Dongle) DC Power : DC 3.7V Ant. Polarization: Vertical Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 106.6299 -11.81 37.60 25.79 43.50 -17.71 peak 100 168 2 157.0699 -7.53 34.34 26.81 43.50 -16.69 peak 200 356 3 335.5500 -6.50 32.51 26.01 46.00 -19.99 peak 200 336 4 432.5500 -4.61 31.59 26.98 46.00 -19.02 peak 200 38 5 511.1200 -4.63 31.65 27.02 46.00 -18.98 peak 200 210 6 704.1499 1.18 28.48 29.66 46.00 -16.34 peak 141 0 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 24 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 4.6. Test Result and Data (1GHz ~ 18GHz) Test Mode : Mode 1: Charging Mode(From Computer) DC Power : DC 3.7V Ant. Polarization: Horizontal Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 1663.000 -14.09 58.12 44.03 74.00 -29.97 peak 100 245 2 2479.000 -10.04 53.66 43.62 74.00 -30.38 peak 100 328 3 3210.000 -7.61 52.67 45.06 74.00 -28.94 peak 200 96 4 3550.000 -6.16 50.64 44.48 74.00 -29.52 peak 100 74 5 4893.000 -3.83 47.62 43.79 74.00 -30.21 peak 100 105 6 6916.000 -0.23 46.90 46.67 74.00 -27.33 peak 100 1 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 25 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 1: Charging Mode(From Computer) DC Power : DC 3.7V Ant. Polarization: Vertical Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 1459.000 -15.21 59.15 43.94 74.00 -30.06 peak 200 85 2 1816.000 -13.22 57.10 43.88 74.00 -30.12 peak 100 327 3 2292.000 -10.87 53.68 42.81 74.00 -31.19 peak 100 15 4 2734.000 -9.27 57.81 48.54 74.00 -25.46 peak 200 224 5 3346.000 -7.03 54.03 47.00 74.00 -27.00 peak 100 96 6 4145.000 -4.18 49.20 45.02 74.00 -28.98 peak 100 264 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 26 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 2: Normal Communication Mode(By Audio cable) DC Power : DC 3.7V Ant. Polarization: Horizontal Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 1663.000 -14.09 58.62 44.53 74.00 -29.47 peak 100 8 2 2190.000 -11.33 58.04 46.71 74.00 -27.29 peak 100 205 3 2785.000 -9.12 55.47 46.35 74.00 -27.65 peak 100 324 4 3210.000 -7.61 52.67 45.06 74.00 -28.94 peak 200 105 5 3550.000 -6.16 50.64 44.48 74.00 -29.52 peak 100 227 6 4893.000 -3.83 47.12 43.29 74.00 -30.71 peak 100 4 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 27 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 2: Normal Communication Mode(By Audio cable) DC Power : DC 3.7V Ant. Polarization: Vertical Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 1459.000 -15.21 61.65 46.44 74.00 -27.56 peak 100 201 2 1901.000 -12.73 59.76 47.03 74.00 -26.97 peak 100 41 3 2734.000 -9.27 56.31 47.04 74.00 -26.96 peak 100 336 4 3125.000 -7.97 54.75 46.78 74.00 -27.22 peak 100 95 5 3346.000 -7.03 52.53 45.50 74.00 -28.50 peak 100 274 6 8242.000 1.92 46.19 48.11 74.00 -25.89 peak 100 9 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 28 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 3: Wireless Communication Mode(By U+Dongle) DC Power : DC 3.7V Ant. Polarization: Horizontal Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 1663.000 -14.09 57.12 43.03 74.00 -30.97 peak 100 328 2 1986.000 -12.25 56.77 44.52 74.00 -29.48 peak 100 45 3 2207.000 -11.25 58.60 47.35 74.00 -26.65 peak 100 75 4 2785.000 -9.12 54.47 45.35 74.00 -28.65 peak 200 93 5 3499.000 -6.38 53.15 46.77 74.00 -27.23 peak 200 214 6 5743.000 -2.49 47.18 44.69 74.00 -29.31 peak 100 102 Note: Measurement Level = Reading Level + Correct Factor Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 29 of 30

CERPASS TECHNOLOGY CORP. Report No.: SEFD1605172 Test Mode : Mode 3: Wireless Communication Mode(By U+Dongle) DC Power : DC 3.7V Ant. Polarization: Vertical Temp : 25 ℃ Humidity : 48% Pressure(mbar) : 1002 Date : 2016/07/21 No. Frequency Factor Reading Level Limit Margin Det. Height Azimuth (MHz) (dB/m) (dBuV) (dBuV/m) (dBuV/m) (dB) (cm) (deg) 1 1459.000 -15.21 59.15 43.94 74.00 -30.06 peak 100 201 2 1850.000 -13.02 58.64 45.62 74.00 -28.38 peak 200 159 3 2190.000 -11.33 59.95 48.62 74.00 -25.38 peak 200 35 4 2734.000 -9.27 55.31 46.04 74.00 -27.96 peak 100 41 5 3346.000 -7.03 53.53 46.50 74.00 -27.50 peak 100 127 6 4026.000 -4.22 53.20 48.98 74.00 -25.02 peak 100 8 Note: Measurement Level = Reading Level + Correct Factor Test engineer: The end Cerpass Technology Corp. Issued Date : Aug 01, 2016 Report format Revision 01 Page No. : 30 of 30


Document Created: 2016-08-31 09:02:31
Document Modified: 2016-08-31 09:02:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC