Test Report

FCC ID: SYW-A1901

Test Report

Download: PDF
FCCID_2862435

                                           FCC PART 15.247
                                               TEST REPORT
                                                              For

                                      Feit Electric Company
                           4901 Gregg Road Pico Rivera, California, United States


                                            FCC ID: SYW-A1901


              Report Type:                                       Product Type:
              Original Report                                    LED Lamp(with bluetooth)



                      Test Engineer:         Liewei Liu


                    Report Number:           RSZ150717551-00B


                        Report Date:         2015-08-07

                                             Candy Li

                       Reviewed By:          RF Engineer

                        Prepared By:         Bay Area Compliance Laboratories Corp. (Shenzhen)
                                             6/F, the 3rd Phase of WanLi Industrial Building
                                             ShiHua Road, FuTian Free Trade Zone
                                             Shenzhen, Guangdong, China
                                             Tel: +86-755-33320018
                                             Fax: +86-755-33320008
                                             www.baclcorp.com.cn




Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated
or used in part without prior written consent from Bay Area Compliance Laboratories Corp.


Bay Area Compliance Laboratories Corp. (Shenzhen)                                                                          Report No.: RSZ150717551-00B




                                                       TABLE OF CONTENTS


GENERAL INFORMATION .......................................................................................................................................4
 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4
 OBJECTIVE ...................................................................................................................................................................4
 RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................4
 TEST METHODOLOGY ..................................................................................................................................................4
 TEST FACILITY .............................................................................................................................................................5
SYSTEM TEST CONFIGURATION ..........................................................................................................................6
  DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................6
  EQUIPMENT MODIFICATIONS .......................................................................................................................................6
  SUPPORT DEVICES DESCRIPTION .................................................................................................................................7
  EXTERNAL I/O CABLE..................................................................................................................................................7
  BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................7
SUMMARY OF TEST RESULTS ...............................................................................................................................8

FCC §15.247 (i) & §1.1307 (b) (1) & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) ..............................9
  APPLICABLE STANDARD ..............................................................................................................................................9
FCC §15.203 - ANTENNA REQUIREMENT .............................................................................................................10
  APPLICABLE STANDARD ............................................................................................................................................10
  ANTENNA CONNECTOR CONSTRUCTION ....................................................................................................................10
FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS .....................................................................................11
  APPLICABLE STANDARD ............................................................................................................................................11
  MEASUREMENT UNCERTAINTY ..................................................................................................................................11
  EUT SETUP ................................................................................................................................................................11
  EMI TEST RECEIVER SETUP .......................................................................................................................................12
  TEST PROCEDURE ......................................................................................................................................................12
  TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................12
  CORRECTED FACTOR & MARGIN CALCULATION .......................................................................................................12
  TEST RESULTS SUMMARY ..........................................................................................................................................13
  TEST DATA ................................................................................................................................................................13
  ENVIRONMENTAL CONDITIONS ..................................................................................................................................13
FCC §15.209, §15.205 & §15.247(d) - SPURIOUS EMISSIONS.............................................................................16
  APPLICABLE STANDARD ............................................................................................................................................16
  MEASUREMENT UNCERTAINTY ..................................................................................................................................16
  EUT SETUP ................................................................................................................................................................16
  EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................17
  TEST PROCEDURE ......................................................................................................................................................17
  TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................18
  CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................18
  TEST RESULTS SUMMARY ..........................................................................................................................................18
  TEST DATA ................................................................................................................................................................19
  ENVIRONMENTAL CONDITIONS ..................................................................................................................................19
FCC §15.247(a) (2) – 6 dB EMISSION BANDWIDTH ............................................................................................22
  APPLICABLE STANDARD ............................................................................................................................................22
  TEST PROCEDURE ......................................................................................................................................................22
  TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................22
  TEST DATA ................................................................................................................................................................22

FCC Part 15.247                                                                                                                                        Page 2 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                                                         Report No.: RSZ150717551-00B


    ENVIRONMENTAL CONDITIONS ..................................................................................................................................22
FCC §15.247(b) (3) - MAXIMUM CONDUCTED OUTPUT POWER ..................................................................25
  APPLICABLE STANDARD ............................................................................................................................................25
  TEST PROCEDURE ......................................................................................................................................................25
  TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................25
  TEST DATA ................................................................................................................................................................26
  ENVIRONMENTAL CONDITIONS ..................................................................................................................................26
FCC §15.247(d) – 100 kHz BANDWIDTH OF FREQUENCY BAND EDGE .......................................................27
  APPLICABLE STANDARD ............................................................................................................................................27
  TEST PROCEDURE ......................................................................................................................................................27
  TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................27
  TEST DATA ................................................................................................................................................................28
  ENVIRONMENTAL CONDITIONS ..................................................................................................................................28
FCC §15.247(e) - POWER SPECTRAL DENSITY .................................................................................................30
  APPLICABLE STANDARD ............................................................................................................................................30
  TEST PROCEDURE ......................................................................................................................................................30
  TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................30
  TEST DATA ................................................................................................................................................................31
  ENVIRONMENTAL CONDITIONS ..................................................................................................................................31
PRODUCT SIMILARITY DECLARATION LETTER ..........................................................................................33




FCC Part 15.247                                                                                                                                        Page 3 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                   Report No.: RSZ150717551-00B

GENERAL INFORMATION
Product Description for Equipment under Test (EUT)
The Feit Electric Company’s product, model number: AOM800/827/LED/HBR (FCC ID: SYW-A1901) or
the "EUT" in this report was a LED Lamp(with bluetooth), which was measured approximately: 6.0 cm (L)
x 6.0cm (W) x12.5 cm (H), rated with input voltage: AC 120V/60 Hz.

Note: This series products model: AOM800827LED/HBR/CAN and AOM800/827/LED/HBR are identical schematics,
the difference among them is just the model number, and model AOM800/827/LED/HBR was selected for fully testing,
the detailed information can be referred to the attached declaration letter that stated and guaranteed by the applicant.

*All measurement and test data in this report was gathered from production sample serial number: 1507025.
(Assigned by BACL, Shenzhen).The EUT supplied by the applicant was received on 2015-07-17.


Objective
This report is prepared on behalf of Feit Electric Company in accordance with Part 2-Subpart J, Part 15-
Subparts A, B and C of the Federal Communication Commissions rules.

The tests were performed in order to determine compliance with FCC Part 15, Subpart C, and section
15.203, 15.205, 15.207, 15.209 and 15.247 rules.


Related Submittal(s)/Grant(s)
No related grant


Test Methodology
All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices.

All emissions measurement was performed at Bay Area Compliance Laboratories Corp. (Shenzhen). The
radiated testing was performed at an antenna-to-EUT distance of 3 meters.

Measurement uncertainty with RF radiated emission is 5.91 dB for 30MHz-1GHz.and 4.92 dB for above
1GHz, 1.95dB for conducted measurement.




FCC Part 15.247                                                                                        Page 4 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                          Report No.: RSZ150717551-00B

Test Facility
The test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located on
the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen,
Guangdong, China.

Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports
submitted to the Federal Communication Commission (FCC). The details of these reports have been found
to be in compliance with the requirements of Section 2.948 of the FCC Rules on October 31, 2013. The
facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.10-
2013.

The Federal Communications Commission has the reports on file and is listed under FCC Registration No.:
382179. The test site has been approved by the FCC for public use and is listed in the FCC Public Access
Link (PAL) database.




FCC Part 15.247                                                                              Page 5 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)              Report No.: RSZ150717551-00B

SYSTEM TEST CONFIGURATION
Description of Test Configuration

For BLE mode, 40 channels are provided to testing:

                                     Frequency                    Frequency
                  Channel                            Channel
                                       (MHz)                        (MHz)
                     1                  2402           21            2442
                     2                  2404           22            2444
                     3                  2406           23            2446
                     4                  2408           24            2448
                     5                  2410           25            2450
                     6                  2412           26            2452
                     7                  2414           27            2454
                     8                  2416           28            2456
                     9                  2418           29            2458
                    10                  2420           30            2460
                    11                  2422           31            2462
                    12                  2424           32            2464
                    13                  2426           33            2466
                    14                  2428           34            2468
                    15                  2430           35            2470
                    16                  2432           36            2472
                    17                  2434           37            2474
                    18                  2436           38            2476
                    19                  2438           39            2478
                    20                  2440           40            2480

EUT was tested with Channel 1, 20 and 40.


Equipment Modifications
No modification was made to the EUT tested.




FCC Part 15.247                                                                Page 6 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                    Report No.: RSZ150717551-00B

Support Devices Description


       Manufacturer           Description            Model                Serial Number

           N/A                  Socket 1              N/A                     DZ002



External I/O Cable

                  Cable Description                 Length (m)   From Port                 To

       Un-shielding Un-detachable AC Cable             1.0         LISN                   Socket


Block Diagram of Test Setup
For conducted emission



                                                                                         LISN


                                                                   EUT

                                                                 Socket
                                                                             1.0 Meter




        Non-Conductive Table
        80 cm above Ground Plane


                                       1.5 Meters




FCC Part 15.247                                                                           Page 7 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                            Report No.: RSZ150717551-00B

SUMMARY OF TEST RESULTS


                  FCC Rules                           Description of Test                Result

       §15.247 (i), §1.1307 (b) (1)&
                                                        RF Exposure                    Compliance
                 §2.1091
                   §15.203                          Antenna Requirement                Compliance

                  §15.207 (a)                AC Line Conducted Emissions               Compliance
            §15.205, §15.209,
                                                     Spurious Emissions                Compliance
               §15.247(d)
              §15.247 (a)(2)                   6 dB Emission Bandwidth                 Compliance

              §15.247(b)(3)                Maximum Conducted Output Power              Compliance

                  §15.247(d)           100 kHz Bandwidth of Frequency Band Edge        Compliance

                  §15.247(e)                        Power Spectral Density             Compliance




FCC Part 15.247                                                                              Page 8 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                 Report No.: RSZ150717551-00B

FCC §15.247 (i) & §1.1307 (b) (1) & §2.1091- MAXIMUM PERMISSIBLE
EXPOSURE (MPE)
Applicable Standard
According to subpart 15.247(i)and subpart §1.1307(b)(1), systems operating under the provisions of this
section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy
level in excess of the Commission’s guidelines.

Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091)

                          (B) Limits for General Population/Uncontrolled Exposure

   Frequency Range        Electric Field           Magnetic Field      Power Density       Ave.eraging Time
        (MHz)            Strength (V/m)            Strength (A/m)        (mW/cm2)             (minutes)

       0.3–1.34               614                       1.63              *(100)                  30
        1.34–30               824/f                    2.19/f            *(180/f²)                30
         30–300               27.5                     0.073                0.2                   30
       300–1500                    /                     /                f/1500                  30
     1500–100,000                  /                     /                  1.0                   30

f = frequency in MHz; * = Plane-wave.e equivalent power density;

According to §1.1310 and §2.1091 RF exposure is calculated.

Calculated Formulary:

Predication of MPE limit at a given distance
S = PG/4R² = power density (in appropriate units, e.g. mW/cm2);
P = power input to the antenna (in appropriate units, e.g., mW);
G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain
factor, is normally numeric gain;
R = distance to the center of radiation of the antenna (appropriate units, e.g., cm);


Calculated Data:

                                                       Max tune-up
                             Antenna Gain              Conducted       Evaluation        Power
              Frequency                                                                             MPE Limit
   Mode                                                  Power          Distance        Density
                (MHz)                                                                               (mW/cm2)
                                                                          (cm)         (mW/cm2)
                            (dBi)      (numeric)     (dBm) (mW)
   BLE            2480       1.5         1.41         6.40      4.37      20             0.001          1.0

Note: To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 20cm
      from nearby persons.

Result: Compliance




FCC Part 15.247                                                                                   Page 9 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                           Report No.: RSZ150717551-00B

FCC §15.203 - ANTENNA REQUIREMENT
Applicable Standard
According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that
furnished by the responsible party shall be used with the device. The use of a permanently attached
antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered
sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a
broken antenna can be replaced by the user, but the user of a standard antenna jack or electrical connector
is prohibited. The structure and application of the EUT were analyzed to determine compliance with
section §15.203 of the rules. §15.203 state that the subject device must meet the following criteria:

a. Antenna must be permanently attached to the unit.
b. Antenna must use a unique type of connector to attach to the EUT.
Unit must be professionally installed, and installer shall be responsible for verifying that the correct
antenna is employed with the unit.
And according to FCC 47 CFR section 15.247 (b), if the transmitting antennas of directional gain greater
than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna
exceeds 6 dBi.


Antenna Connector Construction
The EUT has an internal antenna arrangement which was permanently attached and the antenna gain is
1.5dBi, fulfill the requirement of this section. Please refer to the EUT photos.


Result: Compliance.




FCC Part 15.247                                                                               Page 10 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                   Report No.: RSZ150717551—00B


FCC §15.207 (a) — AC LINE CONDUCTED EMISSIONS

Applicable Standard

FCC§15.207


Measurement Uncertainty

Input quantities to be considered for conducted disturbance measurements maybe receiver reading,
attenuation of the connection between LISN and receiver, LISN voltage division factor, LISN VDF
frequency interpolation and receiver related input quantities, etc.

Based on CISPR 16—4—2:2011, the expended combined standard uncertainty of conducted disturbancetest
at Bay Area Compliance Laboratories Corp. (Shenzhen) is shown as below. And the uncertainty will not
be takeninto consideration for the test data recorded in the report.

                             Port                              Expanded Measurement uncertainty

                           AC Mains                            3.26 dB (k=2, 95% level of confidence)
                            CAT 3                              3.70 dB (k=2, 95% level of confidence)
                            CAT 5                              3.86 dB (k=2, 95% level of confidence)
                            CAT 6                              4.64 dB (k=2, 95% level of confidence)



EUT Setup

                              ... Vertical Reference
                                  Ground Plane                                          Test Receiver


                  * 40 em |                                                         /
                                      Eut                                        lz|5ces
                                                                                     a pa0
                                  N
                                                        BOcm




                                  uiss       P
                      >\                          1                             1
                                                                        N
                              ~
                                      Bonded to Horizontal            Horizontal Reference
                                      Ground Plane                    Ground Plane

                    Note: 1. Supp ort units were connected to second LISN.
                          2. Both of LISNs (AMN) 80 cm from EUT and at the least 80 cm
                                  from other units and other metal planes support units.

The setup of EUT is according with per ANSI C63.10—2013 measurement procedure. The specification
used was with the FCC Part 15.207 limits.

The spacing between the peripherals was 10 cm.

FCC Part 15.247                                                                                         Page 11 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                Report No.: RSZ150717551-00B

The socket was connected to a 120 VAC/60 Hz power source.


EMI Test Receiver Setup
The EMI test receiver was set to investigate the spectrum from 150 kHz to 30 MHz.

During the conducted emission test, the EMI test receiver was set with the following configurations:

                                Frequency Range                         IF B/W
                               150 kHz – 30 MHz                          9 kHz



Test Procedure
During the conducted emission test, the adapter was connected to the outlet of the LISN.

Maximizing procedure was performed on the six (6) highest emissions of the EUT.

All final data was recorded in the Quasi-peak and average detection mode.


Test Equipment List and Details
                                                                                   Calibration    Calibration
     Manufacturer           Description           Model        Serial Number
                                                                                      Date         Due Date
   Rohde & Schwarz       EMI Test Receiver       ESCS30            100176           2015-06-03    2016-06-03
                                                                3560.6650.12-
   Rohde & Schwarz             LISN              ENV216                             2014-12-01    2015-12-01
                                                                 101613-Yb
   Rohde & Schwarz       Transient Limitor       ESH3Z2           DE25985           2015-05-14    2016-05-13

* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have
been performed in accordance to requirements that traceable to National Primary Standards and International System
of Units (SI).


Corrected Factor & Margin Calculation
The Corrected factor is calculated by adding LISN VDF (Voltage Division Factor), Cable Loss and
Transient Limiter Attenuation. The basic equation is as follows:

      Correction Factor = LISN VDF + Cable Loss + Transient Limiter Attenuation

The “Margin” column of the following data tables indicates the degree of compliance with the applicable
limit. For example, a margin of 7 dB means the emission is 7 dB below the limit. The equation for margin
calculation is as follows:

      Margin = Limit – Corrected Amplitude




FCC Part 15.247                                                                                   Page 12 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                               Report No.: RSZ150717551-00B

Test Results Summary
According to the recorded data in following table, the EUT complied with the FCC Part 15.207, the worst
margin reading as below:
                            4.4 dB at 0.225500 MHz in the Line conducted

Refer to CISPR16-4-2:2011 and CISPR 16-4-1:2009, the measured level complies with the limit if

                                             Lm + U(Lm) ≤ Llim + Ucispr

In BACL, U(Lm) is less than Ucispr, if Lm is less than Llim, it implies that the EUT complies with the limit.


Test Data
Environmental Conditions

              Temperature:               25 ℃
        Relative Humidity:                50 %
            ATM Pressure:               101.0 kPa

     The testing was performed by Liewei Liu on 2015-08-02.

     EUT operation mode: Transmitting




FCC Part 15.247                                                                                   Page 13 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                             Report No.: RSZ150717551-00B


     AC 120V/60 Hz, Line

                                                            EMI Auto Test L


                          90

                          80

                          70
                                                                                                               QP
                          60
                                                                                                               AV
           Level in dBμ




                          50

                          40

                          30

                          20

                          10

                          0
                          150k    300   400 500   800 1M           2M     3M     4M 5M 6     8 10M      20M    30M
                                                              Frequency in Hz



                                 Corrected        Correction
         Frequency                                                       Limit             Margin       Detector
                                 Amplitude         Factor
           (MHz)                                                        (dBμV)              (dB)      (PK/Ave./QP)
                                  (dBμV)            (dB)
          0.154000                  47.0             20.0                65.8               18.8              QP
          0.154000                  23.7             20.0                55.8               32.1          Ave.
          0.217500                  54.9             20.0                62.9               8.0               QP
          0.217500                  45.8             20.0                52.9               7.1           Ave.
          0.225500                  57.1             20.0                62.6               5.5               QP
          0.225500                  48.2             20.0                52.6               4.4           Ave.
          0.257500                  43.1             19.9                61.5               18.4              QP
          0.257500                  24.9             19.9                51.5               26.6          Ave.
          0.336930                  46.6             19.9                59.3               12.6              QP
          0.336930                  35.7             19.9                49.3               13.6          Ave.
          0.395850                  38.3             19.9                57.9               19.6              QP
          0.395850                  20.3             19.9                47.9               27.7          Ave.




FCC Part 15.247                                                                                                Page 14 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                            Report No.: RSZ150717551-00B


     AC 120V/60 Hz, Neutral

                                                            EMI Auto Test N


                           90

                           80

                           70
                                                                                                              QP
                           60
                                                                                                              AV
            Level in dBμ




                           50

                           40

                           30

                           20

                           10

                           0
                           150k    300   400 500   800 1M          2M     3M     4M 5M 6     8 10M     20M    30M
                                                              Frequency in Hz



                                  Corrected        Correction
         Frequency                                                       Limit             Margin      Detector
                                  Amplitude         Factor
           (MHz)                                                        (dBμV)              (dB)     (PK/Ave./QP)
                                   (dBμV)            (dB)
          0.157500                  47.2              20.0               65.6               18.4             QP
          0.157500                  24.6              20.0               55.6               31.0         Ave.
          0.218501                  54.7              20.0               62.9               8.2              QP
          0.218501                  45.6              20.0               52.9               7.3          Ave.
          0.225500                  56.1              20.0               62.6               6.5              QP
          0.225500                  47.1              20.0               52.6               5.6          Ave.
          0.261500                  43.1              19.9               61.4               18.3             QP
          0.261500                  26.0              19.9               51.4               25.3         Ave.
          0.367430                  39.5              19.9               58.6               19.1             QP
          0.367430                  22.1              19.9               48.6               26.5         Ave.
          0.400030                  38.3              19.9               57.9               19.6             QP
          0.400030                  20.0              19.9               47.9               27.9         Ave.


Note:
1) Corrected Amplitude = Reading + Correction Factor
2) Correction Factor = LISN VDF (Voltage Division Factor) + Cable Loss
3) Margin = Limit – Corrected Amplitude




FCC Part 15.247                                                                                               Page 15 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                             Report No.: RSZ150717551—00B


FCC §15.209, §15.205 & §15.247(d) — SPURIOUS EMISSIONS

Applicable Standard

FCC §15.247 (d); §15.209; §15.205;

Measurement Uncertainty

All measurements involve certain levels of uncertainties, especially in field of EMC. The factors
contributing to uncertainties are spectrum analyzer, cable loss, antennafactor calibration, antenna
directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency
interpolation, measurement distance variation, site imperfections, mismatch (average), and system
repeatability.

Based on CISPR 16—4—2:2011, the expended combined standard uncertainty ofradiation emissions at Bay
Area Compliance Laboratories Corp. (Shenzhen) is 5.91 dB for 30MHz—1GHz and 4.92 dB for above
1GHz, 1.95dB for conducted measurementat antenna port. And the uncertainty will not be taken into
consideration for the test data recorded in the report


EUT Setup

Below 1 GHz:

                                                             Ant. Tow             Ldm
                                                                                  Nariable
               EUT&                                                          /
               Support Units

                                        Turn Table

                  0.8m I

                                                    1
                                            Ground Plane

                                            Test R&czivqr\
                                                             %          E__3
                                                                 *l PmX o 0 o o
                                                                          a o e




FCC Part 15.247                                                                                Page 16 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                             Report No.: RSZ150717551-00B

Above 1GHz:




The radiated emission tests were performed in the 3 meters test site, using the setup accordance with the
ANSI C63.10-2013. The specification used was the FCC 15.209, and FCC 15.247 limits.

The socket was connected to a 120 VAC/60 Hz power source.


EMI Test Receiver & Spectrum Analyzer Setup
The system was investigated from 30 MHz to 25 GHz.

During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set with the
following configurations:

          Frequency Range            RBW            Video B/W          IF B/W           Detector

         30 MHz – 1000 MHz          100 kHz           300 kHz          120 kHz             QP
                                     1MHz             3 MHz               /                PK
            Above 1 GHz
                                     1MHz              10 Hz              /               Ave.


Test Procedure
Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all
installation combinations.

Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz-1 GHz, peak and
Average detection modes for frequencies above 1 GHz.




FCC Part 15.247                                                                                 Page 17 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                   Report No.: RSZ150717551-00B

Test Equipment List and Details

                                                                        Serial        Calibration   Calibration
    Manufacturer             Description              Model
                                                                       Number            Date        Due Date
          HP                 Amplifier             HP8447E           1937A01046        2015-05-06   2016-05-06
  Rohde & Schwarz        EMI Test Receiver           ESCI                  101120      2014-11-03   2015-11-03
    Sunol Sciences        Bi-log Antenna              JB1             A040904-2        2014-12-07   2017-12-06
         Mini                Amplifier           ZVA-183-S+          5969001149        2015-04-23   2016-04-23
     A.H. System           Horn Antenna          SAS-200/571                135        2015-02-10   2016-02-10
  Rohde & Schwarz         Signal Analyzer           FSIQ26           8386001028        2014-12-11   2015-12-11
    the electro-
                           Horn Antenna               3116            9510-2270        2013-10-14   2016-10-13
   Mechanics Co.
       TDK                   Chamber              Chamber A                  2#        2012-10-15   2015-10-15
         TDK                 Chamber              Chamber B                  1#        2015-07-22   2016-07-22
                                                    ALN-
   DUCOMMUN                Pre-amplifier                              991373-01       2014-08-03    2015-08-03
                                                 22093530-01
         R&S             Auto test Software        EMC32                   V9.10         NCR           NCR

* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have
been performed in accordance to requirements that traceable to National Primary Standards and International System
of Units (SI).


Corrected Amplitude & Margin Calculation
The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the
Amplifier Gain from the Meter Reading. The basic equation is as follows:

        Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain

The “Margin” column of the following data tables indicates the degree of compliance with the applicable
limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin
calculation is as follows:

        Margin = Limit – Corrected Amplitude


Test Results Summary
According to the recorded data in following table, the EUT complied with the FCC Title 47, Part 15,
Subpart C, section 15.205, 15.209 and 15.247.

                   5.03 dB at 2483.50 MHz in the Vertical polarization for High Channel

Refer to CISPR16-4-2:2011 and CISPR 16-4-1:2009, the measured level complies with the limit if

                                              Lm + U(Lm) ≤ Llim + Ucispr

In BACL, U(Lm) is less than Ucispr, if Lm is less than Llim, it implies that the EUT complies with the limit.



FCC Part 15.247                                                                                     Page 18 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)            Report No.: RSZ150717551-00B

Test Data
Environmental Conditions

             Temperature:               25 ℃
        Relative Humidity:               50 %
            ATM Pressure:              101.0 kPa

    The testing was performed by Liewei Liu on 2015-08-02.

    EUT operation mode: Transmitting




FCC Part 15.247                                                              Page 19 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                        Report No.: RSZ150717551-00B

30 MHz-25 GHz:

                                                                                     FCC Part
                           Receiver             Rx Antenna Corrected Corrected
 Frequency                            Turntable                                    15.247/205/209
                                                            Factor Amplitude
   (MHz)          Reading  Detector    Degree Height Polar
                                                             (dB)    (dBμV/m) Limit        Margin
                  (dBμV) (PK/QP/Ave.)           (m) (H/V)                      (dBμV/m)      (dB)
                                         Low Channel (2402 MHz)
    183.36         31.55          QP      56        2.5   H    -15.2     16.35     43.5        27.15
   2402.00         94.42          PK      105       2.2   H       4.97   99.39       /           /
   2402.00         83.98         Ave.    105        2.2   H       4.97   88.95       /           /
   2402.00         85.31          PK      77        1.4   V       4.97   90.28       /           /
   2402.00         74.91         Ave.     77        1.4   V       4.97   79.88       /           /
   2385.03         47.91          PK       1        1.2   H       4.97   52.88      74         21.12
   2385.03         26.88         Ave.      1        1.2   H       4.97   31.85      54         22.15
   2388.72         49.62          PK     355        2.5   H       4.97   54.59      74         19.41
   2388.72         27.00         Ave.    355        2.5   H       4.97   31.97      54         22.03
   2497.68         41.35          PK      76        2.5   H       6.29   47.64      74         26.36
   2497.68         26.63         Ave.     76        2.5   H       6.29   32.92      54         21.08
   4804.00         36.03          PK      130       1.4   V    16.92     52.95      74         21.05
   4804.00         18.66         Ave.    130        1.4   V    16.92     35.58      54         18.42
   7206.00         38.31          PK      217       1.4   V    19.08     57.39      74         16.61
   7206.00         23.02         Ave.    217        1.4   V    19.08     42.10      54         11.90
   9608.00         34.23          PK      25        1.4   V    22.72     56.95      74         17.05
   9608.00         20.35         Ave.     25        1.4   V    22.72     43.07      54         10.93
                                        Middle Channel (2440 MHz)
    183.36         33.20          QP      100       2.0   H    -15.2     17.00     43.5        26.50
   2440.00         95.46          PK      63        1.0   H       4.97   100.43      /           /
   2440.00         85.33         Ave.     63        1.0   H       4.97   90.30       /           /
   2440.00         87.39          PK      188       1.7   V       4.97   92.36       /           /
   2440.00         77.48         Ave.    188        1.7   V       4.97   82.45       /           /
   2388.88         41.32          PK      183       1.6   H       4.97   46.29      74         27.71
   2388.88         23.71         Ave.    183        1.6   H       4.97   28.68      54         25.32
   2483.56         43.05          PK      322       1.7   H       6.29   49.34      74         24.66
   2483.56         20.52         Ave.    322        1.7   H       6.29   26.81      54         27.19
   2487.89         42.75          PK      68        1.9   H       6.29   49.04      74         24.96
   2487.89         24.96         Ave.     68        1.9   H       6.29   31.25      54         22.75
   4880.00         35.01          PK      87        1.1   V    16.91     51.92      74         22.08
   4880.00         17.69         Ave.     87        1.1   V    16.91     34.60      54         19.40
   7320.00         39.38          PK      260       2.0   V    19.40     58.78      74         15.22
   7320.00         24.96         Ave.    260        2.0   V    19.40     44.36      54         9.64
   9760.00         35.60          PK      231       1.5   V    23.79     59.39      74         14.61
   9760.00         20.95         Ave.    231        1.5   V    23.79     44.74      54         9.26


FCC Part 15.247                                                                           Page 20 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                           Report No.: RSZ150717551-00B


                                                                                     FCC Part
                           Receiver             Rx Antenna Corrected Corrected
  Frequency                           Turntable                                    15.247/205/209
                                                            Factor Amplitude
    (MHz)         Reading  Detector    Degree Height Polar
                                                             (dB)    (dBμV/m) Limit        Margin
                  (dBμV) (PK/QP/Ave.)           (m) (H/V)                      (dBμV/m)      (dB)
                                           High Channel (2480 MHz)
    183.36         34.35          QP       111       1.5     H      -15.2   19.15     43.5        24.35
   2480.00         93.74          PK       225       1.5     H       6.29   100.03      /           /
   2480.00         83.86         Ave.      225       1.5     H       6.29   90.15       /           /
   2480.00         84.25          PK        28       1.2     V       6.29   90.54       /           /
   2480.00         73.72         Ave.       28       1.2     V       6.29   80.01       /           /
   2370.44         40.15          PK        28       2.4     V       4.97   45.12      74         28.88
   2370.44         22.26         Ave.       28       2.4     V       4.97   27.23      54         26.77
   2483.50         62.68          PK        52       1.3     V       6.29   68.97      74         5.03
   2483.50         34.69         Ave.       52       1.3     V       6.29   40.98      54         13.02
   2485.67         60.02          PK       343       2.0     V       6.29   66.31      74         7.69
   2485.67         32.55         Ave.      343       2.0     V       6.29   38.84      54         15.16
   4960.00         36.57          PK       276       1.7     V      17.91   54.48      74         19.52
   4960.00         17.86         Ave.      276       1.7     V      17.91   35.77      54         18.23
   7440.00         37.09          PK       102       2.0     V      18.34   55.43      74         18.57
   7440.00         20.52         Ave.      102       2.0     V      18.34   38.86      54         15.14
   9920.00         34.15          PK       134       2.3     V      23.79   57.94      74         16.06
   9920.00         20.67         Ave.      134       2.3     V      23.79   44.46      54         9.54

Note:
Corrected Factor = Antenna factor (RX) + Cable Loss – Amplifier Factor
Corrected Amplitude = Corrected Factor + Reading
Margin = Limit - Corrected. Amplitude




FCC Part 15.247                                                                              Page 21 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                               Report No.: RSZ150717551-00B

FCC §15.247(a) (2) – 6 dB EMISSION BANDWIDTH
Applicable Standard
Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.5 MHz, and
5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz.


Test Procedure
1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal
   from an external generator.
2. Position the EUT without connection to measurement instrument. Turn on the EUT and connect it to
   measurement instrument. Then set it to any one convenient frequency within its operating range. Set a
   reference level on the measuring instrument equal to the highest peak value.
3. Measure the frequency difference of two frequencies that were attenuated 6 dB from the reference
   level. Record the frequency difference as the emission bandwidth.
4. Repeat above procedures until all frequencies measured were complete.



                                                          Signal Analyzer
                  EUT                    Attenuator



Test Equipment List and Details

                                                                                   Calibration    Calibration
     Manufacturer            Description            Model       Serial Number
                                                                                      Date         Due Date
    Rohde & Schwarz        Signal Analyzer         FSIQ26        8386001028        2014-12-11      2015-12-11

* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have
been performed in accordance to requirements that traceable to National Primary Standards and International System
of Units (SI).


Test Data
Environmental Conditions

             Temperature:               26 ℃
        Relative Humidity:              50 %
            ATM Pressure:             101.0 kPa

     The testing was performed by Liewei Liu on 2015-08-02.

     Test Result: Pass.

     Please refer to the following tables and plots.




FCC Part 15.247                                                                                   Page 22 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                                  Report No.: RSZ150717551-00B


    EUT operation mode: transmitting

                                                    Frequency             6dB bandwidth                    Limit
                    Mode             Channel
                                                      (MHz)                   (MHz)                        (kHz)
                                      Low                 2402                     0.727                    500
                   BLE 4.0           Middle               2440                     0.727                    500
                                      High                2480                     0.752                    500



                                       6 dB Emission Bandwidth, Low Channel

                                         Marker 1 [T1 ndB]              RBW        100 kHz      RF Att      30 dB
                          Ref Lvl        ndB              6.00 dB       VBW        300 kHz
                          20.5 dBm       BW    727.45490982 kHz         SWT          5 ms       Unit           dBm
                  20.5
                            10.5 dB Offset                                            1 [T1]             4.44 dBm
                                                                                                                      A
                                                                                                 2.40197896 GHz
                    10                                                               ndB                 6.00 dB
                                                                    1
                                                                                     BW        727.45490982 kHz
                                                     T1                       T2      T1 [T1]            -1.67 dBm
                     0
                                                                                                 2.40159419 GHz
                                                                                      T2 [T1]            -1.56 dBm
                   -10                                                                           2.40232164 GHz
                          1MAX                                                                                       1MA


                   -20



                   -30



                   -40



                   -50



                   -60



                   -70



                  -79.5
                          Center 2.402 GHz                     300 kHz/                                Span 3 MHz

                  Date:          2.AUG.2015    11:45:31




FCC Part 15.247                                                                                                            Page 23 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                                  Report No.: RSZ150717551-00B

                                      6 dB Emission Bandwidth, Middle Channel

                                         Marker 1 [T1 ndB]              RBW        100 kHz      RF Att      30 dB
                          Ref Lvl        ndB              6.00 dB       VBW        300 kHz
                          20.5 dBm       BW    727.45490982 kHz         SWT          5 ms       Unit           dBm
                  20.5
                            10.5 dB Offset                                            1 [T1]             5.29 dBm
                                                                                                                      A
                                                                                                 2.43998497 GHz
                    10                                                               ndB                 6.00 dB
                                                                    1
                                                                                     BW        727.45490982 kHz
                                                     T1                       T2      T1 [T1]            -0.63 dBm
                     0
                                                                                                 2.43959419 GHz
                                                                                      T2 [T1]            -0.74 dBm
                   -10                                                                           2.44032164 GHz
                          1MAX                                                                                       1MA


                   -20



                   -30



                   -40



                   -50



                   -60



                   -70



                  -79.5
                          Center 2.44 GHz                      300 kHz/                                Span 3 MHz

                  Date:          2.AUG.2015    11:49:32




                                       6 dB Emission Bandwidth, High Channel

                                         Marker 1 [T1 ndB]              RBW        100 kHz      RF Att      30 dB
                          Ref Lvl        ndB              6.00 dB       VBW        300 kHz
                          20.5 dBm       BW    751.50300601 kHz         SWT          5 ms       Unit           dBm
                  20.5
                            10.5 dB Offset                                            1 [T1]             6.08 dBm
                                                                                                                      A
                                                                                                 2.47999098 GHz
                    10                                                               ndB                 6.00 dB
                                                                    1
                                                                                     BW        751.50300601 kHz
                                                     T1                       T2
                                                                                      T1 [T1]            0.07 dBm
                     0
                                                                                                 2.47959419 GHz
                                                                                      T2 [T1]            0.16 dBm
                   -10                                                                           2.48034569 GHz
                          1MAX                                                                                       1MA


                   -20



                   -30



                   -40



                   -50



                   -60



                   -70



                  -79.5
                          Center 2.48 GHz                      300 kHz/                                Span 3 MHz

                  Date:          2.AUG.2015    11:56:15



FCC Part 15.247                                                                                                            Page 24 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                               Report No.: RSZ150717551-00B


FCC §15.247(b) (3) - MAXIMUM CONDUCTED OUTPUT POWER
Applicable Standard
According to FCC §15.247(b) (3), for systems using digital modulation in the 902-928 MHz, 2400-2483.5
MHz, and 5725-5850 MHz bands: 1 Watt. As an alternative to a peak power measurement, compliance
with the one Watt limit can be based on a measurement of the maximum conducted output power.
Maximum Conducted Output Power is defined as the total transmit power delivered to all antennas and
antenna elements averaged across all symbols in the signaling alphabet when the transmitter is operating at
its maximum power control level. Power must be summed across all antennas and antenna elements. The
average must not include any time intervals during which the transmitter is off or is transmitting at a
reduced power level. If multiple modes of operation are possible (e.g., alternative modulation methods),
the maximum conducted output power is the highest total transmit power occurring in any mode.


Test Procedure

1. Place the EUT on a bench and set it in transmitting mode.
2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to one
    test equipment.
3. Add a correction factor to the display.


                                                           Power Meter
                  EUT                     Attenuator



Test Equipment List and Details

                                                                                 Calibration      Calibration
    Manufacturer           Description            Model        Serial Number
                                                                                    Date           Due Date
          HP               Power Meter           N1912A         MY5000448         2014-11-03      2015-11-03

          HP               Power Sensor          N1921A         MY54210016        2014-11-03      2015-11-03


* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have
been performed in accordance to requirements that traceable to National Primary Standards and International System
of Units (SI).




FCC Part 15.247                                                                                   Page 25 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                      Report No.: RSZ150717551-00B

Test Data
Environmental Conditions

             Temperature:               26 ℃
        Relative Humidity:              50 %
            ATM Pressure:            101.0 kPa

     The testing was performed by Liewei Liu on 2015-08-02.


    EUT operation mode: Transmitting


                                                  BLE mode

                                                         Conducted
                                        Frequency                      Limit
             Mode        Channel                        Output Power              Result
                                          (MHz)                        (dBm)
                                                           (dBm)
                             Low           2402               4.71      30         Pass
            BLE 4.0       Middle           2440               5.46      30         Pass
                           High            2480               6.32      30         Pass




FCC Part 15.247                                                                        Page 26 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                               Report No.: RSZ150717551-00B


FCC §15.247(d) – 100 kHz BANDWIDTH OF FREQUENCY BAND EDGE
Applicable Standard
In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated
intentional radiator is operating, the radio frequency power that is produced by the intentional radiator
shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level
of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter
demonstrates compliance with the peak conducted power limits. If the transmitter complies with the
conducted power limits based on the use of RMS averaging over a time interval, as permitted under
paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20
dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated
emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated
emission limits specified in §15.209(a) (see §15.205(c)).


Test Procedure
1. Check the calibration of the measuring instrument using either an internal calibrator or a known signal
   from an external generator.
2. Position the EUT without connection to measurement instrument. Turn on the EUT and connect its
   antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured
   frequency within its operating range, and make sure the instrument is operated in its linear range.
3. Set RBW to 100 kHz and VBW of spectrum analyzer to 300 kHz with a convenient frequency span
   including 100 kHz bandwidth from band edge.
4. Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the
   graph with marking the highest point and edge frequency.
5. Repeat above procedures until all measured frequencies were complete.


                                                             Signal Analyzer
                  EUT                     Attenuator


Test Equipment List and Details

                                                                   Serial         Calibration     Calibration
     Manufacturer           Description           Model
                                                                  Number             Date          Due Date
    Rohde & Schwarz       Signal Analyzer        FSIQ26          8386001028       2014-12-11      2015-12-11

* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have
been performed in accordance to requirements that traceable to National Primary Standards and International System
of Units (SI).




FCC Part 15.247                                                                                   Page 27 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)             Report No.: RSZ150717551-00B

Test Data
Environmental Conditions

             Temperature:               26 ℃
        Relative Humidity:              50 %
            ATM Pressure:            101.0 kPa

     The testing was performed by Liewei Liu on 2015-08-02.

     Test Result: Compliance

     Please refer to the following plots.




FCC Part 15.247                                                               Page 28 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                            Report No.: RSZ150717551-00B

                                                 BLE: Band Edge, Left Side
                                           Marker 1 [T1]                RBW   100 kHz     RF Att      30 dB
                          Ref Lvl                      -39.53 dBm       VBW   300 kHz
                           20.5 dBm               2.39818637 GHz        SWT    5 ms       Unit           dBm
                   20.5
                            10.5 dB Offset                                       1 [T1]           -39.53 dBm
                                                                                                                A
                                                                                           2.39818637 GHz
                     10

                           D1 4.38 dBm
                      0



                    -10
                          1MAX                                                                                 1MA
                                 D -15.62 dBm
                                 D2
                    -20



                    -30


                                                   1
                    -40



                    -50



                    -60



                    -70



                  -79.5
                          Center 2.4 GHz                       1 MHz/                            Span 10 MHz

                  Date:            2.AUG.2015   13:18:59



                                                BLE: Band Edge, Right Side
                                           Marker 1 [T1]                RBW   100 kHz     RF Att      30 dB
                          Ref Lvl                      -40.32 dBm       VBW   300 kHz
                          20.5 dBm                2.48365030 GHz        SWT     5 ms      Unit           dBm
                   20.5
                            10.5 dB Offset                                       1 [T1]           -40.32 dBm
                                                                                                                A
                                                                                           2.48365030 GHz
                     10
                           D1 6.07 dBm

                      0



                    -10
                          1MAX D2
                               D -13.93 dBm                                                                    1MA


                    -20



                    -30


                                                                    1
                    -40



                    -50



                    -60



                    -70



                  -79.5
                          Center 2.4835 GHz                   1 MHz/                             Span 10 MHz

                  Date:            2.AUG.2015   12:04:55




FCC Part 15.247                                                                                                      Page 29 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                               Report No.: RSZ150717551-00B


FCC §15.247(e) - POWER SPECTRAL DENSITY
Applicable Standard
For digitally modulated systems, the power spectral density conducted from the intentional radiator to the
antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous
transmission. This power spectral density shall be determined in accordance with the provisions of
paragraph (b) of this section. The same method of determining the conducted output power shall be used to
determine the power spectral density.

Test Procedure
According to KDB558074 D01 DTS Meas Guidance v03r03

1.  Use this procedure when the maximum peak conducted output power in the fundamental emission is
    used to demonstrate compliance.
2. Set the RBW to: 3kHz≤ RBW≤100 kHz.
3. Set the VBW ≥ 3×RBW.
4. Set the span to 1.5 times the DTS bandwidth.
5. Detector = peak.
6. Sweep time = auto couple.
7. Trace mode = max hold.
8. Allow trace to fully stabilize.
9. Use the peak marker function to determine the maximum amplitude level within the RBW.
10. If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat.


                                                             Signal Analyzer
                  EUT                     Attenuator



Test Equipment List and Details

                                                                   Serial         Calibration     Calibration
      Manufacturer          Description           Model
                                                                  Number             Date          Due Date
     Rohde & Schwarz      Signal Analyzer        FSIQ26          8386001028       2014-12-11      2015-12-11

* Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have
been performed in accordance to requirements that traceable to National Primary Standards and International System
of Units (SI).




FCC Part 15.247                                                                                   Page 30 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                             Report No.: RSZ150717551-00B

Test Data
Environmental Conditions

              Temperature:                     26 ℃
        Relative Humidity:                      50 %
             ATM Pressure:                    101.0 kPa

     The testing was performed by Liewei Liu on 2015-08-02

    EUT operation mode: Transmitting

     Test Result: Pass

                                                    Frequency                   PSD                             Limit
      Mode                Channel
                                                      (MHz)                  (dBm/3kHz)                      (dBm/3kHz)

                            Low                           2402                      -9.60                          ≤8
       BLE                 Middle                         2440                      -9.21                          ≤8
                            High                          2480                      -9.11                          ≤8


                                      Power Spectral Density, BLE Low Channel
                                         Marker 1 [T1]               RBW    3 kHz      RF Att       30 dB
                          Ref Lvl                      -9.60 dBm     VBW   10 kHz
                           20.5 dBm              2.40197465 GHz      SWT   310 ms      Unit            dBm
                   20.5
                            10.5 dB Offset                                    1 [T1]             -9.60 dBm
                                                                                                              A
                                                                                            2.40197465 GHz
                     10



                     0


                                                                 1
                    -10
                          1MAX                                                                               1MA


                    -20



                    -30



                    -40



                    -50



                    -60



                    -70



                  -79.5
                          Center 2.402 GHz                   110 kHz/                        Span 1.1 MHz

                  Date:          2.AUG.2015    13:43:20




FCC Part 15.247                                                                                                     Page 31 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)                                         Report No.: RSZ150717551-00B

                                    Power Spectral Density, BLE Middle Channel
                                         Marker 1 [T1]               RBW    3 kHz      RF Att      30 dB
                          Ref Lvl                    -9.21 dBm       VBW   10 kHz
                           20.5 dBm             2.44000551 GHz       SWT   310 ms      Unit           dBm
                   20.5
                            10.5 dB Offset                                    1 [T1]            -9.21 dBm
                                                                                                             A
                                                                                        2.44000551 GHz
                     10



                     0

                                                                 1
                    -10
                          1MAX                                                                              1MA


                    -20



                    -30



                    -40



                    -50



                    -60



                    -70



                  -79.5
                          Center 2.44 GHz                    110 kHz/                     Span 1.1 MHz

                  Date:          2.AUG.2015   13:42:30



                                      Power Spectral Density, BLE High Channel
                                         Marker 1 [T1]               RBW    3 kHz      RF Att      30 dB
                          Ref Lvl                    -9.11 dBm       VBW   10 kHz
                           20.5 dBm             2.47989749 GHz       SWT   310 ms      Unit           dBm
                   20.5
                            10.5 dB Offset                                    1 [T1]            -9.11 dBm
                                                                                                             A
                                                                                        2.47989749 GHz
                     10



                     0

                                                         1
                    -10
                          1MAX                                                                              1MA


                    -20



                    -30



                    -40



                    -50



                    -60



                    -70



                  -79.5
                          Center 2.48 GHz                    110 kHz/                     Span 1.1 MHz

                  Date:          2.AUG.2015   13:41:24




FCC Part 15.247                                                                                                   Page 32 of 33


Bay Area Compliance Laboratories Corp. (Shenzhen)              Report No.: RSZ150717551-00B


PRODUCT SIMILARITY DECLARATION LETTER




                                   ***** END OF REPORT *****




FCC Part 15.247                                                                Page 33 of 33



Document Created: 2019-11-21 03:30:23
Document Modified: 2019-11-21 03:30:23

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC