FCC Part 15.407_UNII-1

FCC ID: SWX-M5N

Test Report

Download: PDF
FCCID_3109498

FCC Certification 15.407 For Compliance Testing internal use only Please keep this page with the report in our internal files NOTES 1) ITEMS IN RED THROUGOUT THE REPORT ARE ITEMS THAT NEED TO BE ADDRESSED BY THE ENG AT THE TIME OF COMPLETION. Template Revision History Authorized by: Revised Revision Date QM <initials>, Reason for Revision By Date 1.0 12/14/14 SM Creation 2.0 12/16/14 AR Created template 3.0 2/18/15 AR Fixed formatting issues L:\Project\2016\p1630038-Ubiquiti\Test Report\UNII-2\p1630038_FCC_Part 15.407_UNII-2_Rev 2.0.docx p1630038_FCC Certification 15.247 DTS Rev1.0

Test Report Prepared for: Ubiquiti Networks, Inc Model: NSM5 Description: NanoStation M5 Serial Number: N/A FCC ID: SWX-M5N IC: 6545A-M5N To FCC Part 15.407 IC RSS-247 Date of Issue: August 22, 2016 On the behalf of the applicant: Ubiquiti Networks, Inc 2580 Orchard Parkway San Jose, CA 95131 Attention of: Kevin Forbey, Regulatory Manager Ph: (408) 942-3085 E-mail: kevin.forbey@ubnt.com Prepared By Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1630038 Paul Hay Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing. All results contained herein relate only to the sample tested. p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 1 of 25

Test Report Revision History Revision Date Revised By Reason for Revision 1.0 July 18, 2016 Paul Hay Original Document 2.0 August 18, 2016 Amanda Reed Updated phone number in test report 3.0 August 22, 2019 Amanda Reed Corrected issues from review p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 2 of 25

Table of Contents Description Page Standard Test Conditions Engineering Practices 6 Test Results Summary 9 Peak Output Power 10 Transmitter Power Spectral Density (PSD) 12 Conducted Spurious Emissions 14 Radiated Spurious Emissions 16 Occupied Bandwidth 18 Frequency Stability 19 RF Exposure 20 A/C Powerline Conducted Emission 22 Emissions at Band Edges 23 Transmitter E.I.R.P. at Various Elevations 24 Test Equipment Utilized 25 p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 3 of 25

ILAC / A2LA Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to the joint ISO-ILAC-IAF Communiqué dated January 2009). The tests results contained within this test report all fall within our scope of accreditation, unless noted below. Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. Testing Certificate Number: 2152.01 FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 4 of 25

The applicant has been cautioned as to the following 15.21 - Information to User The user’s manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 15.27(a) - Special Accessories Equipment marked to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer without an additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 5 of 25

Standard Test Conditions Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI C63.10-2009 and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104°F) unless the particular equipment requirements specified testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Measurement results, unless otherwise noted, are worst-case measurements. Environmental Conditions Temperature Humidity Pressure (ºC) (%) (mbar) 25.5 – 26.5 21.6 – 22.2 976.7 – 980.9 EUT Operation during Tests EUT was powered by POE (Power Over Ethernet) Ethernet cable. EUT Description Model: NanoStation M5 Description: 5GHz MIMO Bridging Solution Serial Number: N/A Additional Information: The EUT is a 2x2 MIMO 802.11a/n radio. The EUT was tested conducted mode with RF connectors mounted on the EUT at the antenna ports. The EUT is powered by POE (Power Over Ethernet) adapter. p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 6 of 25

EUT Specifications EUT Specifications 15.407 Equipment Code NII FCC ID SWX-M5N Model(s)Tested NSM5 Model(s) Covered NSM5 Maximum Output Power 13.8 dBm Frequency Ranges covered 5250-5350 and 5470-5725MHz EUT temperature range -40C to 80C Bandwidths 10/20/30/40 MHz 6, 9, 12, 18, 24, 36, 48, 54, MCS0, MCS1, MCS2, Data Rates MCS3, MCS4, MCS5, MCS6, MCS7, MCS8, MCS9 Modulations BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM Antenna List Model No. Manufacturer Antenna Type Peak Gain NanoStation M5 Ubiquiti Sector 16 15.203: Antenna Requirement: The antenna is permanently attached to the EUT The antenna uses a unique coupling X The EUT must be professionally installed The antenna requirement does not apply p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 7 of 25

Accessories: Qty Description Manufacturer Model S/N Switching mode power 1 Ubiquiti GP-A240-050 N/A supply/ POE 1 Laptop Dell E6420 FHRP6R1 1 Mouse Logitech M100 N/A Cables: Length Shielding Shielded Hood Ferrite Qty Description (M) Y/N Y/N Y/N POE power 1 Ethernet cable <3 meters N N supply Modifications: None p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 8 of 25

Test Results Summary Pass, Specification Test Name Comments Fail, N/A 15.247(b) Peak Output Power Pass 15.247(b) Conducted Spurious Emissions Pass 15.247(d), 15.209(a), 15.205 Radiated Spurious Emissions Pass 15.247(d), 15.209(a), 15.205 Emissions At Band Edges Pass 15.247(a)(2) Occupied Bandwidth Pass 15.247(e) Transmitter Power Spectral Density Pass 15.207 A/C Powerline Conducted Emissions Pass §RSS-247 E.I.R.P. at Various Elevations Pass p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 9 of 25

Peak Output Power Engineer: Paul Hay Test Date: 5/16/16 Test Requirements (2) For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum conducted output power over the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm + 10 log B, where B is the 26 dB emission bandwidth in megahertz. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. Test Procedure The RF power was calculated using the spectrum analyzers’ band power function per Method SA-1 from KDB 789033 D02 General U-NII Test Procedures New Rules v01. Measurements were made at the low, mid, and high channels of the band. The Spectrum Analyzer was set to the following: a. RBW = 1 MHz b. VBW ≥ 3 MHz c. Sweep time = auto d. Detector = RMS e. 100 traces in power averaging mode Test Setup Spectrum EUT Attenuator Analyzer p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 10 of 25

Test Results: For a 16 dBi antenna UNI-2A FCC Band J4 J4 J7 Combined Frequency J7 Level output Width Level Level Level power Limit Margin MHz MHz dBm dBm mW mW dBm dBm dB 10 5255 6.6 6.6 4.5 4.6 9.6 14 -4.4 10 5300 6.7 6.5 4.7 4.5 9.6 14 -4.4 10 5340 3.9 4.0 2.5 2.5 7.0 14 -7.0 20 5260 6.7 6.6 4.7 4.6 9.7 14 -4.3 20 5300 5.9 5.5 3.9 3.5 8.7 14 -5.3 20 5335 4.7 3.8 3.0 2.4 7.3 14 -6.7 30 5265 6.9 7.3 4.9 5.4 10.1 14 -3.9 30 5300 7.0 7.0 5.0 5.0 10.0 14 -4.0 30 5330 4.3 3.8 2.7 2.4 7.1 14 -6.9 40 5270 6.8 7.6 4.8 5.8 10.2 14 -3.8 40 5300 7.1 6.7 5.1 4.7 9.9 14 -4.1 40 5325 4.4 3.8 2.8 2.4 7.1 14 -6.9 UNII-2C Band J4 J4 J7 Combined Frequency J7 Level output Width Level Level Level power Limit Margin MHz MHz dBm dBm mW mW dBm dBm dB 10 5480 5.6 5.0 3.6 3.2 8.3 14 -5.7 10 5600 6.4 5.6 4.3 3.7 9.0 14 -5.0 10 5715 6.6 6.3 4.5 4.2 9.4 14 -4.6 20 5485 7.9 7.8 6.2 6.0 10.9 14 -3.1 20 5600 8.3 7.7 6.7 5.9 11.0 14 -3.0 20 5710 7.7 7.2 5.9 5.2 10.4 14 -3.6 30 5490 10.8 9.5 11.9 8.8 13.2 14 -0.8 30 5600 10.0 9.3 10.0 8.5 12.6 14 -1.4 30 5705 11.0 10.6 12.7 11.5 13.8 14 -0.2 40 5485 8.7 8.4 7.5 6.9 11.6 14 -2.4 40 5590 9.0 10.4 7.9 11.0 12.7 14 -1.3 40 5690 9.7 10.2 9.4 10.5 13.0 14 -1.0 p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 11 of 25

Transmitter Power Spectral Density (PSD) Engineer: Paul Hay Test Date: 5/16/16 Test Requirements (2) For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. Test Procedure The Power Spectral Density was measured using the method per SA-1 from KDB 789033 D02 General U-NII Test Procedures New Rules v01. Measurements were made at the low, mid, and high channels of the band. The maximum PSD was determine by finding the peak value across the carrier bandwidth. The Spectrum Analyzer was set to the following: a. RBW = 1 MHz b. VBW ≥ 3 MHz c. Span 1.5 * BW d. Sweep time = auto e. Detector = RMS f. 100 traces in power averaging mode Test Setup Spectrum EUT Attenuator Analyzer p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 12 of 25

Test Results: For a 16 dBi antenna UNII-2A Band J4 J7 J4 J7 Combined Frequency output Width Level Level Level Level power Limit Margin MHz MHz dBm dBm mW mW dBm dBm dB 10 5255 -2.5 -1.7 0.56 0.68 0.9 1 -0.1 10 5300 -2.2 -2.1 0.60 0.62 0.9 1 -0.1 10 5340 -4.5 -3.9 0.35 0.41 -1.2 1 -2.2 20 5260 -5.0 -5.1 0.32 0.31 -2.0 1 -3.0 20 5300 -5.3 -5.5 0.30 0.28 -2.4 1 -3.4 20 5335 -7.0 -7.9 0.20 0.16 -4.4 1 -5.4 30 5265 -6.4 -5.8 0.23 0.26 -3.1 1 -4.1 30 5300 -6.6 -6.6 0.22 0.22 -3.6 1 -4.6 30 5330 -8.7 -9.2 0.13 0.12 -5.9 1 -6.9 40 5270 -7.4 -7.4 0.18 0.18 -4.4 1 -5.4 40 5300 -7.3 -7.6 0.19 0.17 -4.4 1 -5.4 40 5325 -10.2 -10.7 0.10 0.09 -7.4 1 -8.4 UNII-2C Band J4 J7 J4 J7 Combined Frequency output Width Level Level Level Level power Limit Margin MHz MHz dBm dBm mW mW dBm dBm dB 10 5480 -3.0 -3.1 0.5 0.5 0.0 1 -1.0 10 5600 -2.5 -2.9 0.6 0.5 0.3 1 -0.7 10 5715 -2.3 -2.0 0.6 0.6 0.9 1 -0.1 20 5485 -3.4 -3.2 0.5 0.5 -0.3 1 -1.3 20 5600 -3.1 -3.4 0.5 0.5 -0.2 1 -1.2 20 5710 -4.0 -4.2 0.4 0.4 -1.1 1 -2.1 30 5490 -2.8 -2.6 0.5 0.5 0.3 1 -0.7 30 5600 -3.2 -3.6 0.5 0.4 -0.4 1 -1.4 30 5705 -2.1 -2.4 0.6 0.6 0.8 1 -0.2 40 5485 -5.9 -6.0 0.3 0.3 -2.9 1 -3.9 40 5590 -5.4 -3.5 0.3 0.4 -1.3 1 -2.3 40 5690 -4.2 -4.9 0.4 0.3 -1.5 1 -2.5 p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 13 of 25

Conducted Spurious Emissions Engineer: Paul Hay Test Date: 5/11/16 Test Requirements Unwanted Emissions that fall Outside Restricted Bands For transmitters operating in the 5.25-5.35 GHz band: All emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz. For transmitters operating in the 5.47-5.725 GHz band: All emissions outside of the 5.47-5.725 GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz. As specified in § 15.407(b), emissions above 1000 MHz that are outside of the restricted bands are subject to a maximum emission limit of -27 dBm/MHz. However, an out-of-band emission that complies with both the peak and average limits of § 15.209 is not required to satisfy the -27 dBm/MHz maximum emission limit. The emission measurements shall be performed using a minimum resolution bandwidth of 1 MHz. A lower resolution bandwidth may be employed near the band edge, when necessary, provided the measured energy is integrated to show the total power over 1 MHz The provisions of §15.205 apply to intentional radiators operating under this section Unwanted emissions below 1 GHz must comply with the general field strength limits set forth in §15.209. For Conducted Unwanted Emissions in the Restricted Bands For conducted measurements above 1000 MHz, EIRP was determined and then the field strength computed by the following: E[dBμV/m] = EIRP[dBm] - 20 log(d[meters]) + 104.77, where E = field strength and d = 3m E[dBμV/m] = EIRP[dBm] + 95.2, for d = 3 meters. Test Procedure Per KDB 789033 D02 General U-NII Test Procedures New Rules v01 conducted RF port measurements were made in lieu of radiated. In addition, Cabinet Emissions measurements were performed in a semi-anechoic chamber with the antenna port terminated by a matching load. See additional section for Radiated Emissions. The following criteria were addressed: The Spectrum Analyzer was set to the following for emissions > 1000MHz: a. RBW = 1 MHz b. VBW ≥ 3 MHz c. Detector = Peak. d. Sweep time = auto e. Trace mode = max hold 1. Note: For emissions where the peak exceeded that of the average 15.209 emission limit the following was performed. f. VBW ≤ RBW/100 (i.e., 10 kHz) but not less than 10 Hz For emissions below 1000MHz the Spectrum Analyzer settings were as follows: a. RBW = 100 kHz b. VBW ≥ 300 kHz c. Detector = Peak d. Sweep time = auto e. Trace mode = max hold p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 14 of 25

Test Setup Spectrum EUT Attenuator Analyzer Test Results: See Annex A: Undesirable Emissions Conducted p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 15 of 25

Radiated Spurious Emissions Engineer: Poona Saber Test Date: 5/11/16 Test Requirements The provision of §15.209 were applied. In addition the requirements of §15.205 were also applied. FCC Part 15 Subpart C Paragraph 15.209(a) Limits Frequency Frequency Frequency (MHz) (microvolts/meter) (meter) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30 30 30 30-88 100 3 88-216 150 3 216-960 200 3 Above 960 500 3 Remarks: E field strength (dBμV/m) = 20 log E field strength (uV/m) Test Procedure The EUT was setup in accordance with ANSI C63.10. 2009 and tested per KDB 789033. The antenna was replaced with non-radiating matched load. The EUT is placed on non-conductive platform at a height of 0.8 meters above the ground plane of the semi-anechoic chambers. The EUT was rotated 360 degrees and the receive antenna raised and lowered to find the maximum emissions from 30MHz to the 10th harmonic of the fundamental. The EUT was set to the maximum power level allowed and the low, mid, and high channels were investigated for emissions. The Spectrum Analyzer was set to the following for emissions > 1000MHz: a. (RBW = 1 MHz b. VBW ≥ 3 MHz c. Detector = Peak d. Sweep time = auto e. Trace mode = max hold 1. Note: For emissions where the peak exceeded that of the average 15.209 emission limit the following was performed. f. RBW = 1 MHz g. VBW ≤ RBW/100 (i.e., 10 kHz) but not less than 10Hz For emissions below 1000MHz the Spectrum Analyzer settings were as follows: a. RBW = 100 kHz b. VBW ≥ 300 kHz c. Detector = Peak d. Sweep time = auto e. Trace mode = max hold 1. Note: A quasi peak detector was used for emissions where the peak exceeded that of the average 15.209 emission limits p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 16 of 25

Test Setup below 1000MHz EUT Antenna with Spectrum Preamp Analyzer Test Setup above 1000MHz Band EUT with Antenna Amplifier Spectrum Reject matching load Analyzer Filter Test Results: See Annex B: Undesirable Emission Radiated p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 17 of 25

Occupied Bandwidth Engineer: Paul Hay Test Date: 5/16/16 Test Requirement The emission bandwidth shall be determined by measuring the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, that are 26 dB down relative to the maximum level of the modulated carrier. Determination of the emissions bandwidth is based on the use of measurement instrumentation employing a peak detector function with an instrument resolution bandwidth approximately equal to 1.0 percent of the emission bandwidth of the device under measurement Test Procedure The Spectrum Analyzer was set to the following parameters: a. RBW = approximately 1 to 5% of the emission bandwidth. b. VBW > RBW. c. Detector = Peak. d. Trace mode = max hold. Test Setup EUT Spectrum Analyzer Test Results: See Annex C: Occupied Bandwidth p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 18 of 25

Frequency Stability Engineer: Paul Hay Test Date: 5/18/16 Test Requirement Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user’s manual. Test Procedure a. The EUT was placed into a temperature chamber and the temperature ranges were set to the manufacturer’s specifications. b. The RF output of the EUT was connected to a spectrum analyzer c. The lowest and highest channels of the band were set to transmit d. The carrier plots were measured to insure that the 26dB band width remained within the band over the prescribed temperature extremes. Test Setup Temperature Chamber Spectrum EUT Analyzer Test Results: See Annex D: Frequency Stability p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 19 of 25

RF Exposure Engineer: Paul Hay Test Date: 5/17/16 Requirements U-NII devices are subject to the radio frequency radiation exposure requirements specified in §1.1307(b), §2.1091 and §2.1093 of this chapter, as appropriate. All equipment shall be considered to operate in a “general population/uncontrolled” environment. Applications for equipment authorization of devices operating under this section must contain a statement confirming compliance with these requirements for both fundamental emissions and unwanted emissions. In addition, systems operating under the provisions of this section shall be operated in a manner that insures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. Exposure Limits At operating frequencies less than or equal to 6 GHz, the limits for maximum permissible exposure (MPE) shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in Section 1.1307(b), except for portable devices as defined in §2.1093 as these evaluations shall be performed according to the SAR provisions in §2.1093 of this chapter. MPE Limit Calculations Exposure Limit 1mW/cm2 Source Based Time Averaged Power Calculation Average Power Calculations Average Power = Peak Power * duty-cycle% Band Tuned Frequency Conducted Peak Output Power Duty Cycle Average Power (MHz) (mW) (%) (mW) UNII-2A 5270 10.5 100 0.741 UNII-2C 5705 24.0 100 24.0 p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 20 of 25

MPE Evaluation This is a fixed/mobile device used in uncontrolled /general population exposure environment. Limits Uncontrolled Exposure 0.3-1.234 MHz Limit [mW/cm²] = 100 47 CFR 1.1310 1.34-30 MHz Limit [mW/cm²] = (180/f²) Table 1, (B) 30-300 MHz Limit [mW/cm²] = 0.2 300-1500 MHz Limit [mW/cm²] = f/1500 1500-100,000 MHz Limit [mW/cm²] = 1.0 UNII-2A Test Data Test Frequency, MHz 5270 Power, Conducted, mW (P) 0.741 Antenna Gain Isotropic 16 Antenna Gain Numeric (G) 39.81 Antenna Type Sector Distance (R) 20 𝑃∗𝐺 𝑆= 4𝜋𝑟 2 Power Density (S) mw/cm2 Power mW (P) Numeric Gain (G) Distance (r2) cm 0.741 39.81 20 Power Density (S) = 0.005869 mw/cm2 Limit =(from above table) = 1.0 mw/cm2 UNII-2C Test Data Test Frequency, MHz 5705 Power, Conducted, mW (P) 24.0 Antenna Gain Isotropic 16 Antenna Gain Numeric (G) 39.81 Antenna Type Sector Distance (R) 20 𝑃∗𝐺 𝑆= 4𝜋𝑟 2 Power Density (S) mw/cm2 Power mW (P) Numeric Gain (G) Distance (r2) cm 24.0 39.81 20 Power Density (S) = 0.190082 mw/cm2 Limit =(from above table) = 1.0 mw/cm2 p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 21 of 25

A/C Powerline Conducted Emission Engineer: Paul Hay Test Date: 5/12/16 Test Procedure The EUT power cable was connected to a LISN and the monitored output of the LISN was connected to a transient limiter, which then connected directly to a spectrum analyzer. The conducted emissions from 150 kHz to 30 MHz were measured and compared to the specification limits. Test Setup EUT Transient Spectrum LISN Power Cable Limiter Analyzer Test Results: See Annex E: A/C Powerline Conducted Emission p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 22 of 25

Emissions at Band Edges Engineer: Poona Saber Test Date: 5/19/16 Test Procedure The EUT was tested in a semi-anechoic chamber set 3m from the receiving antenna. A spectrum analyzer was used to verify that the EUT met the requirements for band edge and restricted band for both peak and average measurements. The cable and antenna correction factors were input into the analyzer as a reference level offset to ensure accurate readings. For the restricted band the amplifier and band reject filter correction factors were also input to the spectrum analyzer. Band Edge Test Setup EUT Antenna Spectrum Analyzer Restricted Band Test Setup EUT Antenna Band Reject Amplifier Spectrum Filter Analyzer Test Results: See Annex A Conducted Spurious p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 23 of 25

Transmitter E.I.R.P. at Various Elevations Engineer: Paul Hay Test Date: 7/8/16 Test Requirements (i) For an outdoor access point operating in the band 5.25-5.35 GHz, the maximum power spectral density shall not exceed -13 dBW in any 1 megahertz band for 0°≤ θ< 8°, -13 − 0.716 (θ-8) dBW/MHz for 8° ≤ θ< 40°, -35.9 − 1.22 (θ-40) dBW/MHz for 40° ≤ θ ≤ 45° and -42 dBW/MHz for θ > 45°. θ is the angle above the local horizontal plane (of the Earth). For ease of testing the following conversion was used. 1dbW=31dBm Test Procedure The E.I.R.P was measured using the method per RSS-247 May 2015, Annex A, Method 2. The following equation was followed. e.i.r.p. density = PSDMAX + GNorm + GMAX GNorm = the normalized gain value, in dB (original amplitude axis of the antenna pattern); GMAX = the maximum antenna gain value, in dBi. Worst-Case Tilt Angle EIRP Limit Margin Antenna Polarization (°) (dBm) (dBm) (dBm) NanoStationM5-16 Vertical 45 -12.1 -12 -0.1 p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 24 of 25

Test Equipment Utilized Last Cal Cal Due Description Manufacturer Model # CT Asset # Date Date Temperature Chamber Tenney Tenney II Benchmaster i00287 NCR NCR Preamplifier HP 8447D i00055 NCR NCR Horn Antenna EMCO 3115 i00103 1/20/15 1/20/17 Harmonic Mixer HP 11970A i00193 6/21/15 6/21/17 Horn Antenna, Amplified ARA DRG-118/A i00271 5/8/14 5/8/16 Horn Antenna, Amplified ARA MWH-1826/B i00273 04/22/15 04/22/17 Spectrum Analyzer Agilent E4407B i00331 09/18/15 09/18/16 Bi-Log Antenna Schaffner CBL 6111D i00349 10/8/15 10/8/16 EMI Analyzer Agilent E7405A i00379 2/11/16 2/11/17 3 Meter Semi-Anechoic 3 Meter Semi-Anechoic Panashield i00428 11/26/13 11/26/16 Chamber Chamber PSA Spectrum Analyzer Agilent E4445A i00471 8/26/15 8/26/16 In addition to the above listed equipment standard RF connectors and cables were utilized in the testing of the described equipment. Prior to testing these components were tested to verify proper operation. END OF TEST REPORT p1630038_FCC Part 15.407_IC RSS-247_UNII-2_Rev 3.0 Page 25 of 25


Document Created: 2016-08-23 14:53:37
Document Modified: 2016-08-23 14:53:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC