FCC_Part 1.1310_Rev 3.0.pdf

FCC ID: SWX-BDBAC

RF Exposure Info

Download: PDF
FCCID_4452935

Test Report Prepared for: Ubiquiti Networks, Inc Model: B-DB-AC, Bullet Description: Dual Band Networking Device Serial Number: N/A FCC ID: SWX-BDBAC To FCC Part 1.1310 Date of Issue: September 10, 2018 On the behalf of the applicant: Ubiquiti Networks, Inc 2580 Orchard Parkway San Jose, CA 95131 Attention of: Mark Feil Ph: (408)942-3085 Email: mark.feil@ubnt.com Prepared By Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1790008 Poona Saber Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing All results contained herein relate only to the sample tested p1790008_FCC_Part 1.1310_Rev 3.0 Page 1 of 6

Test Report Revision History Revision Date Revised By Reason for Revision 1.0 January 23, 2018 Poona Saber Original Document 2.0 January 31, 2018 Poona Saber Added a note on page 3 Changed the maximum power and minimum 3.0 September 10, 2018 Poona Saber safe distance based on new power measurements p1790008_FCC_Part 1.1310_Rev 3.0 Page 2 of 6

ILAC / A2LA Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer joint ISO-ILAC-IAF Communiqué dated January 2009) The tests results contained within this test report all fall within our scope of accreditation, unless below Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. Testing Certificate Number: 2152.01 FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A EUT Description Model: B-DB-AC, Bullet Description: Dual Band Networking Device Firmware: N/A Software: N/A Serial Number: N/A Additional Information: The Bullet AC (Model: B-DB-AC) is a dual band networking device that is powered over ethernet (passive POE, 24V) and provides an N-type antenna connection. It features dual- band AC mode operation in 5GHz and 2.4GHz bands, and a dedicated 2.4 GHz WiFi management radio for convenient device setup. EUT Operation during Tests Radio testing has been done conducted and radiated with controlling the device for continuous modulation transmission on low, middle and high channels with client’s provided commands through telnet. Note: Power is brought down one by one for other antennas mathematically so the highest EIRP for 4dBi antenna would be the same for other antennas as well. p1790008_FCC_Part 1.1310_Rev 3.0 Page 3 of 6

Source Based Time Averaged Power Calculation Average Power calculations Average Power = Peak Power * duty-cycle% Point to multipoint application Conducted Peak Output Maximum Tuned Frequency Duty Cycle Average Power Power Tolerance (MHz) (%) (mW) (dBm) (dB) 2437 17.48 2 dB 100 88.71 Point to Point application Conducted Peak Output Maximum Tuned Frequency Duty Cycle Average Power Power Tolerance (MHz) (%) (mW) (dBm) (dB) 5735 23.1 2 dB 100 323.59 p1790008_FCC_Part 1.1310_Rev 3.0 Page 4 of 6

MPE Evaluation for Point to Multipoint Application This is a portable device used in Uncontrolled Exposure environment. Limits Uncontrolled Exposure 0.3-1.234 MHz: Limit [mW/cm²] = 100 47 CFR 1.1310 1.34-30 MHz: Limit [mW/cm²] = (180/f²) Table 1, (B) 30-300 MHz: Limit [mW/cm²] = 0.2 300-1500 MHz: Limit [mW/cm²] = f/1500 1500-100,000 MHz Limit [mW/cm²] = 1.0 Test Data Test Frequency, MHz 2437 Power, Conducted, mW (P) 88.71 Antenna Gain Isotropic 13 dBi Antenna Gain Numeric (G) 19.95 Antenna Type Omni Distance (R) 20 cm 𝑃∗𝐺 𝑆= 4𝜋𝑟 2 Power Density (S) mw/cm 2 Power Density (S) =0.35 Limit = (from above table) = 1 MPE Evaluation for Point to Point Application Test Data Test Frequency, MHz 5735 Power, Conducted, mW (P) 323.59 Antenna Gain Isotropic 34 dBi Antenna Gain Numeric (G) 2511.8 Antenna Type Dish Distance (R) 20 cm 𝑃∗𝐺 𝑆= 4𝜋𝑟 2 Power Density (S) mw/cm 2 Power Density (S) =161.7 Limit = (from above table) = 1 p1790008_FCC_Part 1.1310_Rev 3.0 Page 5 of 6

Minimum Safe Distance Evaluation Since the power density is over the limit the minimum safe distance evaluation is done per below to find the minimum installation distance for power density being below the limit. Test Data Test Frequency, MHz 5735 Power, Conducted, mW (P) 323.59 Antenna Gain Isotropic 34 dBi Antenna Gain Numeric (G) 2511.8 Antenna Type Dish Limit (L) 20 cm R=√(PG/4πL) Distance (R) cm Power mW (P) Numeric Gain (G) Limit (L) 254.38 323.59 2511.8 1 The minimum safe distance for point to point application is 254.38 centimeters. p1790008_FCC_Part 1.1310_Rev 3.0 Page 6 of 6


Document Created: 2019-09-21 00:31:30
Document Modified: 2019-09-21 00:31:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC