Modular Approval Letter

FCC ID: SU3RMBLED

Cover Letter(s)

Download: PDF
FCCID_4456531

RAE Systems, Inc Declaration of the Modular Approval Applicant / Grantee RAE Systems, Inc FCC ID: SU3RMBLED Model: RMBLED The single module transmitter has been evaluated then tested meeting the requirements under Part 15C Section 212 as below: Modular approval requirement EUT Condition Com ply (a) The radio elements of the modular transmitter must have The radio elements of the modular YES their own shielding. The physical crystal and tuning transmitter have their own shielding. capacitors may be located external to the shielded radio elements. (b) The modular transmitter must have The modular has buffered data inputs, it is YES buffered modulation/data inputs (if such inputs are integrated in chip. Please see provided) to ensure that the module will comply with part schematic.pdf 15 requirements under conditions of excessive data rates or over-modulation. (c)The modular transmitter must have its All power lines derived from the host YES own powersupply regulation. device are regulated before energizing other circuits internal to the MM3SB1150Z. Please see schematic.pdf (d) The modular transmitter must comply A permanently attached antenna or unique YES with the antenna and transmission system requirements of antenna connector is not a requirement for Sections 15.203, 15.204(b) and 15.204(c). The antenna licensed modules. must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. (e)The modular transmitter must be tested The MM3SB1150Zwas tested in a YES in a stand-alone configuration, i.e., the module must not be stand‐alone configuration via a PCMCIA inside another device during testing for compliance with extender. Please see conducted set‐up part 15 requirements. Unless the transmitter module will be photo.pdf and spurious set‐up battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with

RAE Systems, Inc the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)) must not be in side another device during testing. (f)The modular transmitter must be The label position of MM3SB1150Zis YES equipped with either a permanently affixed label or must clearly indicated. If the FCC ID of the be capable of electronically displaying its FCC identification number. module cannot be seen when it is installed, then the host label must include the text: Contains FCC ID: 2ADQO3SB1150Z. Please see the label.pdf (g) The modular transmitter must comply The MM3SB1150Zis compliant with all YES with any specific rules or operating requirements that applicable FCC rules. Detail instructions ordinarily apply to a complete transmitter and the are given in the User Manual. manufacturer must provide adequate instructions along with the module to explain any suchrequirements. A copy of these instructions must be included in the application for equipmentauthorizationrequirements,whicharebasedon theintendeduse/configurations. (h)The modular transmitter must comply The MM3SB1150Zis approved to comply YES with any applicable RF exposure requirements in its final with the applicable RF exposure configuration. requirement, please see the MPE evaluation with 20cm as the distance restriction. Dated 2019/8/27 By: James Pan Signature Printed Title: Project Manager On behalf of : RAE Systems, Inc


Document Created: 2019-09-18 14:02:41
Document Modified: 2019-09-18 14:02:41
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC