FCC Part 15.249-900MHz_REV1

FCC ID: SU3-2601

Test Report

Download: PDF
FCCID_2951314

Test report no. 160100634SHA-001 Page 1 of 21 FCC & IC Test Report No. 160100634SHA-001 Applicant : RAE Systems Inc. 3775 N. 1st St., San Jose, California USA 95134. Manufacturer : RAE Systems Inc. 3775 N. 1st St., San Jose, California USA 95134. Product Name : MICRORAE Type/Model : PGM-2601 TEST RESULT : PASS SUMMARY The equipment complies with the requirements according to the following standard(s) or specification: 47CFR Part 15 (2014): Radio Frequency Devices (Subpart C) ANSI C63.10 (2013): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices RSS-210 Issue 8 (December 2010): Low-power Licence-exempt Radio communication Devices (All Frequency Bands): Category I Equipment RSS-Gen Issue 4 (December 2014): General Requirements for Compliance of Radio Apparatus Date of issue: Jan 06, 2016 Prepared by: Reviewed by: Jesse Xu (Project Engineer) Daniel Zhao (Reviewer) FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 2 of 21 Description of Test Facility Name: Intertek Testing Service Limited Shanghai Address: Building No.86, 1198 Qinzhou Road(North), Shanghai 200233, P.R. China FCC Registration Number: 236597 IC Assigned Code: 2402B-1 Name of contact: Jonny Jing Tel: 86 21 61278271 Fax: 86 21 54262353 FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 3 of 21 Content SUMMARY............................................................................................................................................. 1 1 GENERAL INFORMATION ...................................................................................................... 4 1.1 Description of Client ...................................................................................... 4 1.2 Identification of the EUT ............................................................................... 4 1.3 Technical Specification .................................................................................. 5 2 TEST SPECIFICATIONS ............................................................................................................ 6 2.1 Standards or specification .............................................................................. 6 2.2 Mode of operation during the test .................................................................. 6 2.3 Test software list ............................................................................................ 6 2.4 Test peripherals list ........................................................................................ 6 2.5 Instrument list ................................................................................................ 7 2.6 Test Summary ................................................................................................ 8 3 RADIATED EMISSION ...................................................................................................................... 9 3.1 Test limit ........................................................................................................ 9 3.2 Test Configuration ......................................................................................... 9 3.3 Test procedure and test setup ....................................................................... 10 3.4 Test protocol ................................................................................................ 11 4 ASSIGNED BANDWIDTH (20DB BANDWIDTH) ............................................................................... 13 4.1 Limit ............................................................................................................. 13 4.2 Test Configuration ....................................................................................... 13 4.3 Test procedure and test setup ....................................................................... 13 4.4 Test protocol ................................................................................................ 14 5 POWER LINE CONDUCTED EMISSION ........................................................................................... 15 5.1 Limit ............................................................................................................. 15 5.2 Test configuration ........................................................................................ 15 5.3 Test procedure and test set up ...................................................................... 16 5.4 Test protocol ................................................................................................ 17 FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 4 of 21 1 GENERAL INFORMATION 1.1 Description of Client Applicant : RAE Systems Inc. 3775 N. 1st St., San Jose, California USA 95134. Name of contact : James Pan (IC) James Liu (FCC) Tel : 408-952-8217; 408-9528200 Fax : 408-952-8480; 408-952-8487 Email : james.liu@honeywell.com Jungsying.Pan@Honeywell.com Manufacturer : RAE Systems Inc. 3775 N. 1st St., San Jose, California USA 95134. 1.2 Identification of the EUT Product Name : MICRORAE Type/model : PGM-2601 FCC ID : SU3-2601 IC : 20969-2601 FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 5 of 21 1.3 Technical Specification Operation Frequency : 906-924MHz Band Type of Modulation : O-QPSK Description of EUT : Here is one model with BLE and Mersh mode. Among only mesh function was assessed.We tested the 906CH , 916CH and 924CH and listed the worst data in this report. Antenna Designation : PCB antenna Gain of Antenna : -5dBi Rating : Switching Adapter supply: Model: 3A-066WP12 Input: AC 100-240V, 50/60Hz, 0.3A Output: DC 12V, 0.5A Internal battery: 1900mAH, 3.7V EUT type : Table top Floor standing Channel Description : Channel Frequency Channel Frequenc Identifier (MHz) Identifier y (MHz) 1 906 6 916 2 908 7 918 3 910 8 920 4 912 9 922 5 914 10 924 Software applied : SSCOM3.2, Set the power level:6 : Sample received date Nov 08, 2015 Date of test : Nov 10, 2015 ~Dec 28, 2015 FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 6 of 21 2 TEST SPECIFICATIONS 2.1 Standards or specification 47CFR Part 15 (2014) ANSI C63.10 (2013) RSS-210 Issue 8 (December 2010): RSS-Gen Issue 4 (December 2014): 2.2 Mode of operation during the test While testing transmitting mode of EUT, the internal modulation and continuously transmission was applied. 2.3 Test software list Test Items Software Manufacturer Version Conducted ESxS-K1 R&S V2.1.0 emission Radiated ES-K1 R&S V1.71 emission 2.4 Test peripherals list Item No. Name Band and Model Description PC HP ProBook 6450b HP - FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 7 of 21 2.5 Instrument list Equipment Type Manu. Internal Cal. Date Due date no. Test Receiver ESCS 30 R&S EC 2107 2015-10-21 2016-10-20 Test Receiver ESIB 26 R&S EC 3045 2015-10-20 2016-10-19 A.M.N. ESH2-Z5 R&S EC 3119 2015-1-9 2016-1-8 A.M.N. ENV 216 R&S EC 3393 2015-8-9 2016-8-8 A.M.N. ENV 216 R&S EC 3394 2015-8-9 2016-8-8 A.M.N. ENV4200 R&S EC3558 2015-8-9 2016-8-8 Ultra-broadband HL 562 R&S EC 3046-1 2015-5-16 2016-5-14 antenna Bilog Antenna CBL 6112D TESEQ EC 4206 2015-4-28 2017-4-27 Horn antenna HF 906 R&S EC 3049 2015-4-28 2017-4-27 Pre-amplifier Pre-amp 18 R&S EC 3222 2015-4-12 2016-4-11 Semi-anechoic - Albatross EC 3048 2015-5-12 2016-5-11 chamber project High Pass Filter WHKX 1.0/15G- Wainwright EC4297-1 2015-1-8 2016-1-7 10SS Power sensor / N1911A/N1921A Agilent EC4318 2015-04-12 2016-04-11 Power meter FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 8 of 21 2.6 Test Summary This report applies to tested sample only. The test results have been compared directly with the limits, and the measurement uncertainty is recorded. This report shall not be reproduced in part without written approval of Intertek Testing Service Shanghai Limited. TEST ITEM FCC REFERANCE IC REFERANCE RESULT Radiated emission 15.249 & 15.205 RSS-210 Issue 8 Pass Annex A2.9 &Clause 2.2 Assigned bandwidth 15.215(c) - Pass (20dB bandwidth) Occupied bandwidth - RSS-Gen Issue 4 Tested Clause 6.6 Power line conducted emission 15.207 RSS-Gen Issue 4 Pass Clause 8.8 Notes: 1: NA =Not Applicable 2: This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 9 of 21 3 Radiated emission Test result: Pass 3.1 Test limit Fundamental Frequency Fundamental limit Harmonic limit (MHz) (dBuV/m) (dBuV/m) __________________________________________________________ 902 - 928 94 54 2400 - 2483.5 94 54 5725 - 5875 94 54 24000 - 24250 108 68 ________________________________________________________________ The radiated emissions which fall outside allocated band (2400-2483.5MHz), must also comply with the radiated emission limits specified in §15.209(a) showed as below: Frequency Field Strength Measurement Distance (MHz) (dBuV/m) (m) ___________________________________________________________ 30 - 88 40.0 3 88 - 216 43.5 3 216 - 960 46.0 3 Above 960 54.0 3 ________________________________________________________________ 3.2 Test Configuration EUT Antenna mast Turn Table Test receiver FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 10 of 21 3.3 Test procedure and test setup The measurement was applied in a semi-anechoic chamber. While testing for spurious emission higher than 1GHz, if applied, the pre-amplifier would be equipped just at the output terminal of the antenna. Tabletop devices shall be placed on a nonconducting platform with nominal top surface dimensions 1 m by 1.5 m. For emissions testing at or below 1 GHz, the table height shall be 80 cm above the reference ground plane. For emission measurements above 1 GHz, the table height shall be 1.5 m. The turn table rotated 360 degrees to determine the position of the maximum emission level. The EUT was set 3 meters away from the receiving antenna which was mounted on an antenna mast. The antenna moved up and down between from 1meter to 4 meters to find out the maximum emission level. The radiated emission was measured using the Spectrum Analyzer with the resolutions bandwidth set as: RBW = 300 Hz, VBW = 1 kHz (9 kHz~150 kHz); RBW = 10 kHz, VBW = 30 kHz (150 kHz~30MHz); RBW = 100 kHz, VBW = 300 kHz (30MHz~1GHz for PK) RBW = 1MHz, VBW = 3MHz (>1GHz for PK); RBW = 1MHz, VBW = 10Hz (>1GHz for AV); FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Intertek Testreporino. 160100635tta.001 Page 11 or21 34 Test protocol Temperature i2 °c Relative Humidiy i8 The low fiequency, which stanted from 9 KFz to 30MHe, was pre—scanned and the esult which was 2048 lower than the Himit fine per 15.31(0) was not reported 30MHe—1GHe, Horizontal tm wir on oa zo sor sn 7Take is Famece i es iesimane ies i2s Vertical waeomer raswnsies ree tnsu2s0! 1casssozen1 TMRFIS2@0_¥1 ©2018menck

Test report no. 160100634SHA-001 Page 12 of 21 Correct Corrected Frequency Limit Margin CH Antenna Factor Reading Detector (MHz) (dBuV/m) (dB) (dB/m) (dBuV/m) H 906.69 25.10 85.70 94.00 8.30 PK H 1783.56 -15.10 49.20 54.00 4.80 PK H 3623.24 -6.60 38.60 54.00 15.40 PK H 226.33 13.20 39.20 46.00 6.80 PK L V 906.69 25.70 78.80 94.00 15.20 PK V 1783.56 -15.10 55.10 74.00 18.90 PK V 1783.56 -15.10 52.10 54.00 1.90 AV V 2635.27 -10.80 42.40 54.00 11.60 PK V 226.33 13.20 29.80 46.00 16.20 PK H 916.47 25.10 86.93 94.00 7.07 PK H 1833.24 -14.25 51.20 54.00 2.80 PK H 3665.11 -6.02 37.67 54.00 16.33 PK M V 916.47 25.10 79.45 94.00 14.55 PK V 1833.24 -14.25 54.98 74.00 19.02 PK V 1833.24 -14.25 51.69 54.00 2.31 AV V 3665.11 -6.02 43.11 54.00 10.89 PK H 924.19 25.20 84.70 94.00 9.30 PK H 1849.32 -13.10 50.25 54.00 3.75 PK H 3670.21 -5.87 39.45 54.00 14.55 PK H V 924.19 25.20 79.11 94.00 14.89 PK V 1849.32 -13.10 55.24 74.00 18.76 PK V 1849.32 -13.10 52.24 54.00 1.76 PK V 3670.21 -5.87 38.11 54.00 15.89 PK Remark: 1. Correct Factor = Antenna Factor + Cable Loss (-Amplifier, is employed); 2. Corrected Reading = Original Receiver Reading + Correct Factor; 3. Margin = Limit – Corrected Reading; 4. If the PK Corrected reading is lower than AV limit, the AV test can be elided; Example: Assuming Antenna Factor = 30.20dB/m, Cable Loss = 2.00dB, Gain of Preamplifier = 32.00dB, Original Receiver Reading = 10dBuV, Then Correct Factor = 30.20 + 2.00 – 32.00 = 0.20dB/m, Corrected Reading = 10dBuV + 0.20dB/m = 10.20dBuV/m, Assuming limit = 54dBuV/m, Corrected Reading = 10.20dBuV/m, Then Margin = 54 -10.20 = 43.80dBuV/m. FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Intertek Testreyorine. reoroossesita.o01 Page is otal 4 Assigned bandwidth (20dB bandwidth) Test results Pass 4d Limit Tntentional radiators must be designed to ensure that the 20 dB bandividth of the emission is contained within the allocated fequency band as clause 3.1 shows Tfrequency stability is not specifie n the regulations,is recommended thatthe fundamental ernission be kept within at leastthe central 80% of the permntted band in order to minimize the possibility of out—of—band operation 42 Test Configuration Spectrum Analyzer RF inpur & Eut n Antenma connector 4.3 Test procedure and test setup The 204B Bandwidth per FCC § 15.215(c)is measured using the Spectrum Analyzer. Set Span = 2 to 3 times the 20 dB bandwidth, RBW = approximately 1% ofthe 20 dB bandwidh, VBW>RBW, Sweep = auto, Detector = peak, Trace = max hold The test was performed at 3 channels (lowest, midde and highest channel} ree tnsu2s0! 1casssozen1 TMRFIS2@0_¥1 ©2018menck

Test report no. 160100634SHA-001 Page 14 of 21 4.4 Test protocol Temperature : 23 °C Relative Humidity : 55 % 20dB bandwidth 80% of permitted band Result (MHz) (MHz) 905.56 ~ 924.45 904.60 ~ 925.40 Pass L Channel H Channel FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 15 of 21 5 Power line conducted emission Test result: Pass 5.1 Limit Conducted Limit (dBuV) Frequency of Emission (MHz) QP AV 0.15-0.5 66 to 56* 56 to 46 * 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. 5.2 Test configuration EUT Peripheral devices LISN LISN EMI receiver For table top equipment, wooden support is 0.8m height table For floor standing equipment, wooden support is 0.1m height rack. FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 16 of 21 5.3 Test procedure and test set up Measured levels of ac power-line conducted emission shall be the emission voltages from the voltage probe, where permitted, or across the 50 Ω LISN port (to which the EUT is connected), where permitted, terminated into a 50 Ω measuring instrument. All emission voltage and current measurements shall be made on each current- carrying conductor at the plug end of the EUT power cord by the use of mating plugs and receptacles on the LISN, if used. Equipment shall be tested with power cords that are normally supplied or recommended by the manufacturer and that have electrical and shielding characteristics that are the same as those cords normally supplied or recommended by the manufacturer. For those measurements using a LISN, the 50 Ω measuring port is terminated by a measuring instrument having 50 Ω input impedance. All other ports are terminated in 50 Ω loads. Tabletop devices shall be placed on a platform of nominal size 1 m by 1.5 m, raised 80 cm above the reference ground plane. The vertical conducting plane or wall of an RF-shielded (screened) room shall be located 40 cm to the rear of the EUT. Floor- standing devices shall be placed either directly on the reference ground-plane or on insulating material as described in ANSI C63.4. All other surfaces of tabletop or floor-standing EUTs shall be at least 80 cm from any other grounded conducting surface, including the case or cases of one or more LISNs. The bandwidth of the test receiver is set at 9 kHz. FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 17 of 21 5.4 Test protocol Temperature : 23 °C Relative Humidity : 56 % L line Test Data: Quasi-peak Average Frequency (MHz) level Limit Margin level limit Margin dB(µV) dB(µV) (dB) dB(µV) dB(µV) (dB) 0.45 45.97 56.85 10.88 34.45 46.85 12.40 0.55 48.16 56.00 7.84 36.62 46.00 9.38 0.72 44.92 56.00 11.08 31.96 46.00 14.04 16.86 43.79 60.00 16.21 31.94 50.00 18.06 * * * * * * * * * * * * * * Note: * means the emission level 10dB lower than the relevant limit. FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 18 of 21 N line Test Data: Quasi-peak Average Frequency (MHz) level Limit Margin level limit Margin dB(µV) dB(µV) (dB) dB(µV) dB(µV) (dB) 0.54 42.93 56.00 13.07 31.74 46.00 14.26 0.78 40.29 56.00 15.71 27.94 46.00 18.06 17.90 42.97 60.00 17.03 29.08 50.00 20.92 * * * * * * * * * * * * * * * * * * * * * Note: * means the emission level 10dB lower than the relevant limit. FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 19 of 21 6 Occupied Bandwidth Test Status: Tested 6.1 Test limit None 6.2 Test Configuration See clause 3.2. 6.3 Test procedure and test setup The occupied bandwidth per RSS-Gen Issue 4 Clause 4.6.1 was measured using the Spectrum Analyzer. 6.4 Test protocol Temperature :23 °C Relative Humidity :55 % Channel Occupied Bandwidth Max. Value (KHz) (KHz) 906 821.04 821.04 916 822.43 822.43 924 830.20 830.20 Remark: “Max. Value” is the maximum test result of all the measured occupied bandwidth. FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 20 of 21 FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek

Test report no. 160100634SHA-001 Page 21 of 21 FCC ID:SU3-2601 IC:20969-2601 TTRF15.249_V1 ©2015Intertek


Document Created: 2016-01-21 14:34:05
Document Modified: 2016-01-21 14:34:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC