SAR Report Add Model EF501R Part 5

FCC ID: SS4EF501X

RF Exposure Info

Download: PDF
FCCID_4183379

D Dt&C DASY5 Validation Report for Head TSL Date: 23.08.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2— SN:920 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: £= 2450 MHz; 0 = 1.86 S/m; : = 37.7; p = 1000 kg/m? Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.88, 7.88, 7.88) @ 2450 MHz; Calibrated: 30.12.2017 * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 26.10.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 * DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=3mm, dy=Smm, dz=5mm Reference Value = 115.8 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 26.4 W/kg SAR(I g) = 13.3 W/kg; SAR(1O g) = 6.18 W/kg Maximum value of SAR (measured) = 21.8 W/kg 0 dB =21.8 W/kg = 13.38 dBW/kg Cortficate No: D2450V2—020_Aug18 Page 5 of 8

W©Dt&C_____.___________ _ _ Impedance Measurement Plot for Head TSL Eie Wew Channel Sweep Calbration Trace: Scale Marker: System Wndow tieb 2450000 GHz §7.925 0 124.26 pH 19128 0 2450000 GHz 70.529 mU 13.614° thiAug» 2o Ch: Stae 225000 Glte — Step 25000 Gite 50000 GHz —2$.033 48 i: Sn 225000 on — Sp assoonore Certificate No: D2450V2—920_Aug18 Page 6 of 8 IRiARPSWT(usyreit i0 riomons ue vupyiy eie iervanne w un repers m

D Di&C DASY5 Validation Report for Body TSL Date: 24.08.2018 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2— SN:920 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 2.02 8/m; e = 51.8; p = 1000 kg/m® Phantom section: Flat Section Measurement Standard: DASYS (IEEEAEC/ANSI C63.19—2011) DASYS52 Configuration: * Probe: EX3DV4 — SN7349; ConvF($.01, 8.01, 8.01) @ 2450 MHz; Calibrated: 30.12.2017 * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 26.10.2017 * Phantom: Flat Phantorn 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 «_ DASY52 52.10.1(1476); SEMCAD X 14.6.11(7439) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 109.0 V/m; Power Drift = —0.06 dB Peak SAR (extrapolated) = 26.2 Wikg SAR(L g) = 13.3 W/kg; SAR(10 g) = 6.22 Wikg Maximum value of SAR (measured) = 21.6 W/kg dB 0 5.00 —10.00 —15.00 —20.00 ~25.00 0 dB =21.6 Wikg= 13.34 dBW/g Certificate No: D2450V2—020_Aug18 Page 7 of 8 hm n rowerpuup ue w vosmis se vupyiny eniecaoue w uns repurs manoue un oy appruve + eyen ieeven

_ Dt&C_ _ Impedance Measurement Plot for Body TSL ie Mew Channel Sweep Calbration: Trace: Scale. Marker System Window Help ' 2450000 GHz §2.131 0 400.30 pH 616220 2450000 GHz 63.726 mU 87.470 ° criaug» 20 Chit: Stat 225000 Gite — Step 2.48000 Gite o 0o 2450000 CHz —2}.914 48 se ce co Te assare ore LCL Certficate No: D2450V2—920_Aug18 Page 8 of 8 nrerersr=ou iquay ie t i misnmane ue sopyrng arnu is

Calibration Laboratory of «7 zon sonmutreriecher Ketlorersianst Schmid & Partner i&-_///é’:fi + 5 Iinemiees @étatonnage Engineering AG T ss s C sersice svessro ut teraiws Zoughausstrasse 49, 8004 Zurich, Switzerland "ifoys Cmnanes?) S suiss Calibration Service Accredited by the Swiss Accredtation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilteral Agreement for the recognition of callbration cortifiates Calibration date: This callbraion certficate documents the traceabiityto national standards, which realizethe physical unts of measurements (S1). The measurements and the unsertaities wih confidence probablity are given on the folowing pages and are part of the certficate. All calbrations have been conductad in the clased laborataryfaciity: environment temperature (22 + 3)°C and humidty <70%. Callbration Equipment used (MATE crtical for calbration) Primary Standards B Cal Date (Cortfiato No.) Scheduled Caltbration Power mater NRP sn: torrre Ot—Apr—17 (No. 217—00s21000800) Aprrs Power sensor NRP—281 SN: rosass ot—Apr—t7 (No. 217—00521) Apers Power sensor NRP—291 shtroseis oé—Apr—17 (No. 217—02522) Apers Reference 20 0B Attenuator shi sose 20 07—Apr—17 (No. 217—02508) Aprrs Type—N mismatch combination SN:5047.2/06027 Or—Ap—t7 (No.217—02528) Aorts Reference Probe EXSDV4 sn:asos 50—Dec—17 (No. EX3—3503_Dect7) Dec—ts oags si:eor 26—0ct—17 (No. DAEA—601_Oott?) os—1s Secondary Standards e heck Date (in house) Scheduled Check Power moter EPM—442A SN: aBsreao704 07—0ct—15 (n house check Oct18) in house chock: Oct—18 Powar sensor HP 8481A SN Usarasa7es 07—Oct—15 (nhouse check Oct18) In house checc Oct—18 Power sensor HP 8481A SN: MYA10GR3TT 07—Oct—15 (inhouse check Oct—16) In house checc Oct—18 RF genarator R&S SMT—06 sn: tooor2 15—Jun—15 (in house check Oct—16) In house checkc Oct—18 Network Analyzer HP 8759E sn ussrasoses 18—0ct—01 (in house check Oct—17) in house checkc Oct—18 Function Signature Calibrated by: frican / Approved by: Issued: March 21, 2018 This calbration cortficate shall not be reproduced except in full wihout writen approval of the laboratory. Certificate No: DSGHzV2—1212_Feb18 Page 1 of 16 nrsrenmmou i waie riwi im se wupy ww erawis w uinrepen iminan o rne appre ces —2——

TD Dt&C Calibration Laboratory of Schwelzorischer Kallbrierdienst w o © Schmid & Partner Service suisse étalonnage Engineering AG es Servizio svizzero dtaratura Zeughausstrasse 43, 8004 Zurich, Switzerland 4,,,//7;\\\33 Swiss Callbration Service Waials Accredited by the Swiss Accrodiation Sorvice (GAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multiateral Agreement for the recognition of callbration certifates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy.z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013,"IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR)from hand—held and body—mounted devices used next to the ear(frequency range of 300 MHz to 6 GHz)®, July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)*, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacerto position its feed point exactly below the center marking of theflat phantom section, with the arms oriented parallel to the body axis. * Feed PointImpedance and Return Loss: These parameters are measured with the dipole positioned underthe liquid filled phantom. The impedance stated is transformed from the measurementat the SMA connectorto the feed point. The Return Loss ensures low reflected power. No uncertainty required. © Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normaldistribution correspondsto a coverage probability of approximately 95%. Certiicate No: DSGHzV2—1212_Fob18 Page 2 of 16 h tw ce ie raws orvmmema wire wopeiny uis ie raumw uinropors

W©DH&C _____ o — — — Measurement Conditions DASY system confiquration, as far as not given on page 1. DASY Version DASYS Vs2.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom V5.0 Distance Dipolo Center— TSL 10 mm with Spacer Zoom Scan Resolution dx, dy = 4.0 mm, dz =1.4 mm Graded Ratio = 1.4 (Z direction) 5200 Mz a 1 MHz 5300 Mz a 1 MHz Frequency 5500 Mz a 1 MHz 5600 MHz a 1 MHz 5800 Mz a 1 MHz Head TSL parameters at 5200 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 36.0 4.68 mho/m Measured Head TSL parameters (22.0 2 0.2) °C 36.4 26 % 4.53 mho/m 6% Head TSL temperature change during test <0.5°C ~« m SAR result with Head TSL at 5200 MHz SAR averaged over 1 om(1 g) of Head TSL Condition SAR measured 100 mW input power 7.95 Whkg SAR for nominal Head TSL parameters normalized to 1W 79.6 Wikg + 19.9 % (k=2) SAR averaged over 10 cm® (10 g) of Head TSL condition SAR measured 100 mW input power 2.26 Whkg SAR for nominal Head TSL parameters normalized to 1W 22.6 Wikg 2 19.5 % (k=2) Cortificate No: DSGHzV2—1212_Feb18 Page 3 of 16 nrsrenmmou i waie riwi im se wupiy ww e rawi w un iepen s

W©DH&C _____ in ~——— ~——— _ Head TSL parameters at 5300 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 220 °C s59 4.76 mhotm Measured Head TSL parameters (22.0202)°C 36.3 18 % 4.64 mho/m £6 % Head TSL temperature change during test <0.5°C — SAR result with Head TSL at 5300 MHz SAR averaged over 1 om" (1 g) of Head TSL Condition SAR measured 100 mW input power 8.10 Wikg SAR for nominal Head TSL parameters normalized to 1W B1.1 W/ ky + 19.9 % (ke2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 100 mW input power 231 Wig SAR for nominal Head TSL parameters normalized to 1W 28.1 Wikg 2 19.5 (ke2) Head TSL parameters at 5500 MHz The followingparameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.6 4.98 mho/m Measured Head TSL parameters (22.0 £0.2) °C 36.0 26 % 4.84 mho/m +6 % Head TSL temperature change during test <0.5°C ~—~ SAR result with Head TSL at 5500 MHz SAR averaged over1 cm(1 g) of Head TSL Condition SAR measured 100 mW input power 8.53 Whg SAR for nominal Head TSL parameters normalized to 1W 85.4 Wikg 2 19.9 % (ke2) SAR averaged over 10 om* (10 g) of Head TSL condition SAR measured 100 mW input power 2.40 Whg SAR for nominal Head TSL parameters normalized to 1W 24.0 Wikg 2 19.5 % (k=2) Certificate No: DBGHzV2—1212_Feb18 Page 4 of 16 nrsrenmmou i waie riwi im se wupiy ww e rawi w un iepen s

D Dt&C o Head TSL parameters at 5600 MHz The followingparameters and calculations were applied. Temporature Permittivity Conductivity Nominal Head TSL parameters 22.0°C 355 5.07 mhoim Measured Head TSL parameters (22.0 £0.2) °C 35.8 2 6 % 4.95 mho/m 26 % Head TL temperature change during test <0.5°C s« SAR result with Head TSL at 5600 MHz SAR averaged over 1 em‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 8.35 Whg SAR for nominal Head TSL parameters normalized to 1W 83.6 Wikg + 19.9 % (k=2) SAR averaged over 10 om® (10 g) of Head TSL condition SAR measured 100 mW input power 2.38 Whkg SAR for nominal Head TSL paramoters normalized to 1W 23.8 Wikg 2 19.5 % (k=2) Head TSL parameters at 5800 MHz Thefollowing paramaters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 35.9 5.27 mhoim Measured Head TSL parameters (22.0 £0.2) °C 35.5 2 6 % 5.16 mho/m 26 % Head TSL temperature change during test <0.5 °C + SAR result with Head TSL at 5800 MHz SAR averaged over 1 m‘ (1 g) of Head TSL Condition SAR measured 100 mW input power 7.95 Wig SAR for nominal Head TSL parameters normalized to 1W 79.5 Wikg 2 19.9 % (k=2) SAR averaged over 10 m (10 g) of Head TSL condition SAR measured 100 mW input power 224 Whg SAR for nominal Head TSL parameters normalized to 1W 22.4 Wikg 2 19.5 % (k=2) Cortficate No: DSGHzV2—1212_Feb18 Page 5 of 16 nierermou use i0 i riomins sre cupyiny ainu iemimaus w uina repars imainanc wmprvres

W©DH&C_____ a—_— _ _ a—_— Body TSL parameters at 5200 MHz Thefollowing parameters and calculations were applied. Temperature Pormittivity Conductivity Nominal Body TSL parameters 220°C 49.0 5.30 mho/m Measured Body TSL parameters (r20202)°C 47526 % 541 mhoim £6 % Body TSL temperature change during test <0.5°C SAR result with Body TSL at 5200 MHz SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 100 mW input power 731 Whg SAR for nominal Body TSL parameters normalized to 1W 72.7 Wikg + 19.9 % (k=2) SAR averaged over 10 em* (10 g) of Body TSL condition SAR measured 100 mW input power 2.03 Whg SAR for nominal Body TSL parameters normalizedto 1W 20.2 Wikg + 19.5 % (k=2) Body TSL parameters at 5300 MHz The following parameters and calculations were applied. Temporature Permittivity Conductivity Nominal Body TSL parameters 220 °C 48.9 5.42 mhoim Measured Body TSL parameters (22.020.2) °C 47.3 26 % 5.54 mhoim £6 % Body TSL temperature change during test <05°C SAR result with Body TSL at 5300 MHz SAR averaged over 1 om® (1 g) of Body TSL Condition SAR measured 100 mW input power 7.57 Whg SAR for nominal Body TSL parameters normalized to 1W 75.2 Whkg + 19.9 % (k=2) SAR averaged over 10 em* (10 g) of Body TSL condition SAR measured 100 mW input power 211 Whg SAR for nominal Body TSL parameters normalized to 1W 20.9 Wikg 2 19.5 % (k=2) Cortificate No: DSGHzV2—1212_Feb18 Page 6 of 16 nreremmou iwayie riws ©isnmens se uy m e rear w un epes

_WDH&C _ _ _ _ Body TSL parameters at 5500 MHz The following parameters and calculations were applied. Temperature Pormittivity Conductivity Nominal Body TSL parameters 22.0°C 186 5.65 mho/m Measured Body TSL parameters (22.0 : 02) °C 47.026% 5.80 mho/m # 8 % Body TSL temperature change during test <05°C SAR result with Body TSL at 5500 MHz SAR averaged over 1 om" (1 g) of Body TSL Condition SAR moasured 100 mW input power 8.04 Whg SAR for nominal Body TSL parameters normalized to 1W 79.9 Wikg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.22 Whq SAR for nominal Body TSL parameters normalized to 1W 22.0 Wikg 219.5 % (k=2) Body TSL parameters at 5600 MHz The following parameters and calculations were applied. Temperature Pormittivity Conductivity Nominal Body TSL parameters 220 °C 485 5.77 mho/m Measured Body TSL parameters (22.0£02) °C 46.8 26 % 5.95 mhoim =6 % Body TSL temperature change during test <05°C — SAR result with Body TSL at 5600 MHz SAR averaged over1 cm(1 g) of Body TSL Condition SAR measured 100 mW input power 7.94 Whg SAR for nominal Body TSL parameters normalized to 1W 78.9 Wikg 2 19.9 % (k=2) SAR averaged over 10 em* (10 g) of Body TSL condition SAR measured 100 mW input power 2.20 Whkg SAR for nominal Body TSL parameters normalized to 1W 21.8 Wikg 2 19.5 % (k=2) Cortificate No: DSGHzV2—1212_Feb18 Page 7 of 16 nrsrenmmou i waie riwi im se wupiy ww e rawi w un iepen s

TW Dt&C _ —— —— —— —— —— Body TSL parameters at 5800 MHz The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 48.2 6.00 mhofm Measured Body TSL parameters (22.0 2 0.2) °C 46.4 26 % 6.23 mho/m 6 % Body TSL temperature change during test <05°C ~— — SAR result with Body TSL at 5800 MHz SAR averaged over 1 om® (1 g) of Body TSL Condition SAR measured 100 mW input power 7.62 Wig SAR for nominal Body TSL parameters normalized to 1W 75.7 Wg 2 19.9 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 100 mW input power 2.10 Wikg SAR for nominal Body TSL parameters normalized to 1W 20.8 Wikg 2 19.5 % (k=2) Certificate No: DSGHzV2—1212_Feb18 Page 8 of 16 Arerersr=ou iquag ie is cismmens uie vupyy en eenwun epes m

D Di&C Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL at 5200 MHz Impedance, transformed to feed point 1830 —37 jn Return Loss —27.8 4B Antenna Parameters with Head TSL at 5300 MHz Impedance, transformed to feed point 478 0—0.1 jo Return Loss —33.0 08 Antenna Parameters with Head TSL at 5500 MHz Impedance, transformed to feed point 468 0 +14j0 Return Loss —28.8 0B Antenna Parameters with Head TSL at 5600 MHz Impedance, transformed to feed point s0.4 n +8.1 )2 Return Loss —30.2 48 Antenna Parameters with Head TSL at 5800 MHz Impedance, transformed to feed point s200 +32j0 Return Loss —28.2 0B Antenna Parameters with Body TSL at 5200 MHz Impediance, transformed to feed point ar90—a7j0 Return Loss —27.3 dB Antenna Parameters with Body TSL at 5300 MHz Impedance, transformed to feed point 4860 +200 Return Loss —82.0 dB Antenna Parameters with Body TSL at 5500 MHz Impedance, transformed to feed point 47.4 0 +3.1 2 Return Loss —27.5 08 Certificate No: DSGHzV2—1212_Feb18 Page 9 of 16 hm n rowerpuup ue w vosmis se vupyiny eniecaoue w uns repurs manoue un oy appruve + eyen un neven

_ _ _ _ _ Antenna Parameters with Body TSL at 5600 MHz Impedance, transformed to feed point so.s 9 +4.0 jn Return Loss —28.0 aB Antenna Parameters with Body TSL at 5800 MHz Impedance, transformed to feed point s25 0 + 4.4 jn Return Loss —26.2 aB General Antenna Parameters and Design | Electrical Delay (one direction) 1191 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On someof the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the ‘Measurement Conditions® paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections nearthe feedpoint may be damaged Additional EUT Data Manufactured by SPEAG Manufactured on November 14, 2014 Cortificate No: D6GHzV2—12 12_Fob18 Page 10 of 16 nrerersr=ou i qway ie is ismm wie vupyiny en nereare w un epes s


Document Created: 2019-02-21 21:05:43
Document Modified: 2019-02-21 21:05:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC