Users Manual

FCC ID: SS3-T650A1609

Users Manual

Download: PDF
FCCID_3179044

User Manual Preparing Aircraft and Battery Exiting Packing Mode The aircraft enters Packing Mode to enable easy packing during transportation. It is required to disable Packing Mode when using the aircraft on its first use. 1. Plug in both Intelligent Flight Batteries onto the aircraft. Powering on to exit Packing Mode. 2. Press and release on the power button on the Intelligent Flight Batteries for up to 5 times to exit Packing Mode. Installing Camera and Gimbal Power off the aircraft. 1. Press and hold the mounting button on the gimbal mount. 2. Align the white dot on the camera connector with the red dot on the gimbal mount, follow by mounting the camera onto the gimbal mount. 3. Rotate the locking ring on the camera so that the red dot on the camera is aligned with the red dot on the gimbal mount.

Using the Remote Controller Press and release the power button on the remote controller, wait for 3 seconds then press and hold the power button to power on the remote controller. Aircraft Diagram 1. FPV (First Personal View) Camera 2. Obstacle Sensing System 3. Quick Release Mount 4. Vision Positioning System 5. Landing Gear Servo 6. Graphic Processing System 7. Front LED 8. Motor 9. Propellers 10. Rear LED 11. Intelligent Flight Battery 12. Power Button 13. Battery Level Indicator

14. Battery Eject Button 15. Top Sensor 16. Aircraft Status Indicator 17. SSD Port 18. USB Port 20. USB Mode Button 21. Link Button Remote Controller Diagram [1] Antennas Relays aircraft control and video signal. [2] Mobile Device Holder Securely mounts your mobile device to the remote controller. [3] Control Stick Switch between Mode 2 and Mode 1 by using the DJI GO app. [4] RTH Button Press and hold the button to initiate Return to Home (RTH).

[5]Transformation Switch This switch comprises of two options. Toggle this switch to lower or retract the landing gear. [5] Battery Level LEDs Displays the battery level of the remote controller. [7]Status LED Displays the remote controller's system status. [7] Power Button Used to turn the remote controller on and off. [8] RTH LED Circular LED around the RTH button displays RTH status. [10] Camera Settings Dial Turn the dial to adjust camera settings. [11] Pause Button Press this button to pause the current operations including Tapfly, Follow me. [13]Shutter Button Press to take a photo. [12] Flight Mode Switch Use this switch to switch between

A(Atti), S(Sports) and P(Positioning) mode. [14]Record Button Press to start recording video. [15] Gimbal Dial Tilt Gimbal [16] HDMI Port Use this port to relay HDMI signal to HDMI devices [17] Micro USB Port Reserve for future use. [18] CAN Port Reserve for future use. [19] USB Port Connect to mobile device for running the DJI GO app. [21] C1 Button [22] Power Port Connect to the Charging Hub to charge the battery of the remote controller. [23] C2 Button Using the Remote Controller Press once to check the battery level from the battery level LEDs. Follow the steps below

to turn on your remote controller: 1. The Battery Level LEDs will display the current battery level. 2. Press once, then again and hold to turn on/off Remote Controller. 3. Repeat Step 2 to turn off the remote controller. Battery Turning ON/OFF Slide both the batteries into the battery slots on the rear of the aircraft until it is securely attached on the slots. Turning On: Press the Power Button once, then press again and hold for 2 seconds to turn on. The Power LED will turn red and the remote controller system status screen will display the current battery level. Turning Off: Press the Power Button once, then press again and hold for 2 seconds to turn off. Power level indicators turn off when it is power down. The battery power LED will flash when powering off the Phantom to allow automatically stopping of a recording during the event recording wasn’t stopped.

Remove the Intelligent Flight Battery Press the curricula Battery Eject button to eject both the batteries from the aircraft. Charging the Batteries 1. Connect the Battery Charger to a power source (100-240 V 50/60 Hz). 2. Connect the one end of the Battery Charger to the supplied Charging Hub to start charging. 3. The Battery Level Indicator will display the current battery level as it is charging. 4. The Intelligent Flight Battery is fully charged when the Battery Level Indicators are all off. The Battery Level Indicators will turn off when charging is complete. Detach the batteries from the Charging Hub. Allow its temperature to drop to room temperature before storing it for an extended period. The charger will stop charging the battery if the battery cell’s temperature is not within the operating range (5°C to 40°C ). Powering on aircraft and remote controller 1. Power on the remote controller before powering the aircraft. 2. Launch the DJI GO app and enter “Camera” view.

Starting/Stopping the Motors Starting the Motors A Combination Stick Command (CSC) is used to start the motors. After the motors start release both control stcks. Stopping the Motors There are io. methods to stop the motors. When Phantom 4 has landec. push the left stick down then conduct the same CSC that was used to start the motors as described above . Release both sliks once motors stop. When the aieraft has lnde. push and hold the left stick dowin. 0 > Specifications Modet Teoon Aireraft Weight (Battery— & 33759 Propelles Includedt

Diagonal Distance 605mm (Propellers Excluded) Max Ascent Speed 6 m/s ( Sport mode ) Max Descent Speed 4 m/s（descending）/ 7m/s(diving) Max Speed 20 m/s ( Sport mode ) Max Service Ceiling 6000m Above Sea Level Flight Time 25miin Operating -10°C to 40°C Temperature Satellite Positioning GPS/GLONASS Systems Hovering Precision Vertical +/- 0.1 m (VPS enabled)；+/- 0.5 m Horizontal： +/- 0.3 m (VPS enabled)；+/- 1.5 m Gimbal Controllable Range Pitch: -90°to +30°roll： -90°to +30°pan： ±320° Stabilization 3-axis (pitch, roll, pan) Obstacle Obstacle Sensing Front： 0.7 - 30 m 0-8m (Top ToF sensing range) Sensing Range 0-4m System FOV Forward sensing： Horizontal Range: 60°，Vertical Range: 54° ±5° Detecting Range Forwarding: 10 Hz，Upward： 20Hz Operating Front view ： Surfaces with clear patterns and Environment adequate lighting (lux > 15) surface with distinctive patterns Vision Velocity Range ≤ 22.4mph (36kph) at 6.6ft (2m) above ground Positioning Altitude Range 0m to10m Status Operating Range 0m to10m Detecting Frequency 10 Hz Operating Surfaces with clear patterns and adequate lighting Environment (lux > 15) Altitude Altitude Range 5cm-500cm Sensing Detecting Range 1 cm System Detecting Frequency 20Hz Operating Surface with no sound absorbing features. Environment Model GL6D10A

Max Transmission FCC: 5000 m ； CE: 3500 m （ 2.4 GHz no Remote Distance interference, unobstructed） Controller FCC: 5000 m ； CE: 2000 m （ 5.8 GHz no interference, unobstructed） Operating 0°C to 40°C Temperature Battery 6000 mAh LiPo 2S Operating Voltage 7.4V @ 1.2A FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information T650A complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. For model GL6D10A, SAR tests are conducted using standard operating positions accepted by the FCC/IC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC/IC that it does not exceed the exposure limit established by the FCC/IC, Tests for each product are performed in positions and locations as required by the FCC/IC. For Handheld operation, this device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal.

IC RSS Warning This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. IC Radiation Exposure Statement: This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. T650A should be installed and operated with minimum distance 20cm between the radiator& your body. Cet appareil est conforme aux limitesd'exposition de rayonnement RF IC établiespour un environnement non contrôlé. Cetémetteur ne doit pas être co-implanté oufonctionner en conjonction avec toute autreantenne ou transmetteur. T650A doit être installé et utiliséavec une distance minimale de 20cm entre leradiateur & votre corps. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. KCC Warning Message “해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.” “해당 무선설비는 운용 중 전파혼신 가능성이 있음” NCC Warning Message 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，

EdSZEIRTENRREUET. iEAtiEMES . 1k EoMeiF EMA EME. 1t3 *IMEMATEAmAfE®R TLE NEREEH EERIAIET ENATH. EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro—compliance & (€1313 EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany


Document Created: 2019-10-24 17:12:22
Document Modified: 2019-10-24 17:12:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC