Test Report

FCC ID: SS3-201309581

Test Report

Download: PDF
FCCID_2095683

Report No.: $Z13090014W02 Issued to SZ DJI TECHNOLOGYCO.,LTD For 5.8G Transmitter Model Name: PVTS81 Trade Name: DJI Brand Name: DJI FCC ID: $$3—201309581 Standard: 47 CFR Part 15 Subpart C Test date: 2013—9—3 to 2013—9—26 Issue date: 2013—9—26 Shenzhen MORLAB Com#mnicabio®i chnolo@. Tested by //k, Buon A reimy F24 Un Nie Quan Peng Huarui (Test Engineer) (Project Manager) Date Loly, 0, 16 Date hy sf > Date lfllz . qyé n cooemetner OFTA uns e TAF) GCF‘ QBuetmoth 5CC Reg. No iEeErss oTA .-:EE, zZ2 Za Iniogatera,; 206 ittiemt snn BaTF 695796 The report refers onls t the sumple tested and does not applyto the buil. This report is issued in confidence to the clent andit will bestrietlytroated as such by the Shenthen MORLAB Communication Technology Ca., Lit. It maynot be reproducedratherin its entirety or in part and it may not be used foradverting. The elient to whom the report is issued may, however, show or sendit o a certfied copy there ofprepared by the Shenzhen MORLAB Telecommunication Co.,Lid to is customer Supplier or athers persons directlyconcerned. Shenzhen MORLARTelecommunication Co., Lid will not, withoutthe consent of the cient enter imto any discussion ofcorrespondence with any thindparty concerning the contents of the report In the event of the improper use ofthe report Shenzhen MORLAB Telecommunication Co.. Lid reserves the rightsto withdravwit and to adopt any ather remedies which maybe appropriate Shenzhen MORLAB Communication Technology Co , Ltd Tel: +86 755 36698555 Fax: +86 755 36698525

SZ13090014W02 DIRECTORY 1. GENERAL INFORMATION .................................................................................................... 3 1.1. EUT Description ....................................................................................................................... 3 1.2. Test Standards and Results ........................................................................................................ 4 1.3. Facilities and Accreditations ..................................................................................................... 5 2. 47 CFR PART 15C REQUIREMENTS .................................................................................... 6 2.1. Antenna requirement ................................................................................................................. 6 2.2. Peak Output Power.................................................................................................................... 6 2.3. Bandwidth ................................................................................................................................. 8 2.4. Conducted Spurious Emissions and Band Edge ..................................................................... 11 2.5. Power spectral density (PSD) ................................................................................................. 16 2.6. Conducted Emission ............................................................................................................... 19 2.7. Radiated Emission................................................................................................................... 21 Change History Issue Date Reason for change 1.0 September 26, 2013 First edition Page 2 of 32

SZ13090014W02 1. General Information 1.1. EUT Description EUT Type ............................. :5.8G Transmitter Serial No. .............................. : (n.a, marked #1 by test site) Hardware Version ................. : V2.0 Software Version .................. : V1.0 Applicant .............................. : SZ DJI TECHNOLOGY CO.,LTD Room 613、614, 6/F, HKUST SZ IER Bldg, No.9 Yuexing 1st Rd Hi-Tech Park(South), Nanshan District, Shenzhen, Guangdong, China Manufacturer ........................ : SZ DJI TECHNOLOGY CO.,LTD(Baoan Branch) Room 311~320,Office Bldg.,Zhongyuntai Industrial Park,Songbai Rd.,Shiyan Town, Bao'an District, Shenzhen, Guangdong, China Frequency Range .................. : 5728MHz~5844MHz Channel Number................... : 16 Modulation Type .................. : GFSK Antenna Type........................ : Dipole Antenna Antenna Gain ........................ : 2.0dBi Note 1: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Note 2: The antenna connector of EUT is designed with permanent attachment and no consideration of replacement. Channel list Channel No. Frequency/MHz Channel No. Frequency/MHz 1 5728 9 5793 2 5733 10 5801 3 5742 11 5804 4 5750 12 5810 5 5757 13 5818 6 5759 14 5827 7 5773 15 5835 8 5784 16 5844 Page 3 of 32

SZ13090014W02 1.2. Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C for the EUT FCC ID Certification: No. Identity Document Title 1 47 CFR Part 15 Radio Frequency Devices (10-1-12 Edition) Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 15.203 Antenna Requirement PASS 2 15.247(b) Peak Output Power PASS 3 15.247(a) Bandwidth PASS 4 15.247(d) Conducted Spurious Emission and Band edge PASS 5 15.207 Conducted Emission N/A 6 15.209 ,15.247(d) Radiated Emission PASS 7 15.247(e) Power spectral density (PSD) PASS The tests of Conducted Emission and Radiated Emission were performed according to the method of measurements prescribed in ANSI C63.4 2009. These RF tests were performed according to the method of measurements prescribed in KDB558074 D01 V02 10/04/2012. Page 4 of 32

SZ13090014W02 1.3. Facilities and Accreditations 1.3.1. Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at FL.1, Building A, FeiYang Science Park, Block 67, BaoAn District, Shenzhen, 518101 P. R. China. The test site is constructed in conformance with the requirements of ANSI C63.10 2009, ANSI C63.4 2009 and CISPR Publication 22; the FCC registration number is 695796. 1.3.2. Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 15 - 35 Relative Humidity (%): 30 -60 Atmospheric Pressure (kPa): 86-106 Page 5 of 32

|ORLABS w $Z13090014W02 2. 47 CFR Part 15C Requirements 2.1. Antenna requirement 2.1.1. Applicable Standard According to FCC 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions ofthis section. 2.1.2. Result: Compliant The EUT has a permanently and irreplaceable attached antenna. Please refer to the EUT internal photos. 2.2. Peak Output Power 2.2.1. Requirement According to FCC section 15.247(b)(3), For systems using digital modulation in the 902—928 MHz, 2400—2483.5 MHz, and 5725—5850 MHz bands: The maximum peak conducted output power of the intentional radiator shall not exceed1 Watt. 2.2.2. Test Description The measured output power was calculated by the reading of the Power Meter and calibration. A. Test Setup: EUT Power PC meter —WM @'\ (if necessary ) Attenuator 2 (Rh/[odule) The EUT (Equipment under the test) which is powered by the Battery is coupled to the Power Meter; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading, all test result in power meter. B. Equipments List: Description Manufacturer Model Serial No. Cal. Date_| Cal. Due EPM Series Power Meter Agilent E4418B GB43318055 2013.05.12 2014.05.11 Power Sensor Agilent 8482A MY41091706 2013.05.12 2014.05.11 Page 6 of 32

SZ13090014W02 2.2.3. Test Result The lowest, middle and highest channels are selected to perform testing to verify the conducted RF output peak power of the Module. Measured Output Peak Power Limit Channel Frequency (MHz) Verdict dBm W dBm W 1 5728 17.26 0.053211 PASS 8 5784 17.39 0.054828 30 1 PASS 16 5844 17.69 0.058749 PASS Page 7 of 32

SZ13090014W02 2.3. Bandwidth 2.3.1. Requirement According to FCC section 15.247(a) (2), Systems using digital modulation techniques may operate in the 902 - 928 MHz, 2400 - 2483.5 MHz, and 5725 - 5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 2.3.2. Test Description A. Test Set: The EUT which is powered by the Battery, is coupled to the Spectrum Analyzer; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading. Make the measurement with the spectrum analyzer's resolution bandwidth (RBW) = 100 kHz. In order to make an accurate measurement, set the span greater than RBW. B. Equipments List: Description Manufacturer Model Serial No. Cal. Date Cal. Due Spectrum Analyzer Agilent E4447A US62552411 2013.05.12 2014.05.11 2.3.3. Test Result The lowest, middle and highest channels are selected to perform testing to record the 6 dB bandwidth of the Module. A. Test Verdict: Frequency 6 dB Bandwidth Channel Refer to Plot Limits(kHz) Result (MHz) (MHz) 1 5728 1.021 Plot A ≥500 PASS 8 5784 1.016 Plot B ≥500 PASS 16 5844 1.036 Plot C ≥500 PASS B. Test Plots Page 8 of 32

SZ13090014W02 (Plot A: Channel 1: 2405.376MHz) (Plot B: Channel 18: 2440.192MHz) Page 9 of 32

SZ13090014W02 (Plot C: Channel 36: 2477.056MHz) Page 10 of 32

SZ13090014W02 2.4. Conducted Spurious Emissions and Band Edge 2.4.1. Requirement According to FCC section 15.247(c), in any 100kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. 2.4.2. Test Description A. Test Set: The EUT which is powered by the Battery, is coupled to the Spectrum Analyzer; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading. Make the measurement with the spectrum analyzer's resolution bandwidth (RBW) = 100 kHz. In order to make an accurate measurement, set the span greater than RBW. B. Equipments List: Description Manufacturer Model Serial No. Cal. Date Cal. Due Spectrum Analyzer Agilent E4447A US62552411 2013.05.12 2014.05.11 2.4.3. Test Result The measurement frequency range is from 30MHz to the 10th harmonic of the fundamental frequency. The lowest, middle and highest channels are tested to verify the spurious emissions. A. Test Verdict: Measured Max. Limit (dBm) Frequency Channel Out of Band Refer to Plot Carrier Calculated Verdict (MHz) Emission (dBm) Level -20dBc Limit 1 5728 -40.03 Plot A.1 16.85 -3.10 PASS 8 5784 -41.46 Plot B.1 17.04 -3.00 PASS 16 5844 -37.24 Plot C.1 17.17 -2.80 PASS B. Test Plots: Note: the power of the Module transmitting frequency should be ignored. Page 11 of 32

SZ13090014W02 (Plot A.1: Channel = 1, 30MHz to 40GHz) Page 12 of 32

SZ13090014W02 (Band edge @Channel = 1) Page 13 of 32

SZ13090014W02 (Plot B.1: Channel = 18, 30MHz to 40GHz) Page 14 of 32

SZ13090014W02 (Plot C.1: Channel = 36, 30MHz to 40GHz) (Band edge @Channel = 36) Page 15 of 32

SZ13090014W02 2.5. Power spectral density (PSD) 2.5.1. Requirement According to FCC section 15.247(e), the same method of determining the conducted output power shall be used to determine the power spectral density. If a peak output power is measured, then a peak power spectral density measurement is required. If an average output power is measured, then an average power spectral density measurement should be used. 2.5.2. Test Description A. Test Set: The EUT which is powered by the Battery, is coupled to the Spectrum Analyzer; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading. B. Equipments List: Description Manufacturer Model Serial No. Cal. Date Cal. Due Spectrum Analyzer Agilent E4447A US62552411 2013.05.12 2014.05.11 2.5.3. Test Result A. Test Verdict: Spectral power density (dBm/3kHz) Frequency Measured PSD Limit Channel Refer to Plot Verdict (MHz) (dBm/3kHz) (dBm/3kHz) 1 5728 4.615 Plot A 8 PASS 8 5784 4.544 Plot B 8 PASS 16 5844 5.759 Plot C 8 PASS Measurement uncertainty: ±1.3dB B. Test Plots: Page 16 of 32

SZ13090014W02 (Plot A: Channel = 1) (Plot B: Channel = 18) Page 17 of 32

SZ13090014W02 (Plot C: Channel = 36) Page 18 of 32

|ORLABS w $Z13090014W02 2.6. Conducted Emission 2.6.1. Requirement According to FCC section 15.207, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency within the band 150kHz to 30MHz shall not exceed the limits in the following table, as measured using a 50uH/50Q line impedancestabilization network (LISN). Frequency range (MHz) Conducted Limit (dBuV) Quai—peak Average 0.15 — 0.50 66 to 56 56 to 46 0.50 — 5 56 46 5— 30 60 50 NOTE: (a) The lower limit shall apply at the band edges. (b) The limit decreases linearly with the logarithm of the frequency in the range 0.1 5 — 0.50MHz. 2.6.2. Test Description A. Test Setup: =40cm > <80cm > Communication Antenna \gUT (Wi—FiModule) => a I Pulse Limiter <80cm >} LISN i Receiver | ——o o— Y "=s" Service Supplier The Table—top EUT was placed upon a non—metallic table 0.8m above the horizontal metal reference ground plane. EUT was connected to LISN and LISN was connected to reference Ground Plane. EUT was 8Ocm from LISN. The set—up and test methods were according to ANSI ©63.4:2009 B. Equipments List: Description Manufacturer Model Serial No. Cal. Date_| Cal. Due Receiver Agilent E7405A US44210471 2013.05.12 2014.05.11 Page 19 of 32

SZ13090014W02 Description Manufacturer Model Serial No. Cal. Date Cal. Due LISN Schwarzbeck NSLK 8127 812744 2013.05.12 2014.05.11 Service Supplier R&S CMU200 100448 2013.05.12 2014.05.11 Pulse Limiter (20dB) Schwarzbeck VTSD 9561-D 9391 (n.a.) (n.a.) 2.6.3. Test Result The EUT is designed can not to be connected to the public utility (AC) power line, so conducted emission is unnecessary. Page 20 of 32

SZ13090014W02 2.7. Radiated Emission 2.7.1. Requirement According to FCC section 15.247(d), radiated emission outside the frequency band attenuation below the general limits specified in FCC section 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in FCC section 15.205(a), must also comply with the radiated emission limits specified in FCC section 15.209(a). According to FCC section 15.209 (a), except as provided elsewhere in this subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency (MHz) Field Strength (µV/m) Measurement Distance (m) 0.009 - 0.490 2400/F(kHz) 300 0.490 - 1.705 24000/F(kHz) 30 1.705 - 30.0 30 30 30 - 88 100 3 88 - 216 150 3 216 - 960 200 3 Above 960 500 3 Note: 1. For Above 1000MHz, the emission limit in this paragraph is based on measurement instrumentation employing an average detector, measurement using instrumentation with a peak detector function, corresponding to 20dB above the maximum permitted average limit. 2. For above 1000MHz, limit field strength of harmonics: 54dBuV/m@3m (AV) and 74dBuV/m@3m (PK) In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), also should comply with the radiated emission limits specified in Section 15.209(a)(above table) 2.7.2. Test Description A. Test Setup: 1) For radiated emissions from 9kHz to 30MHz Page 21 of 32

SZ13090014W02 2) For radiated emissions from 30MHz to1GHz Page 22 of 32

SZ13090014W02 3) For radiated emissions above 1GHz The test site semi-anechoic chamber has met the requirement of NSA tolerance 4dB according to the standards: ANSI C63.4 (2009). The EUT was set-up on insulator 80cm above the Ground Plane. The set-up and test methods were according to ANSI C63.4. The EUT of the EUT is powered by the Battery charged with the AC Adapter which is powered by 120V, 60Hz AC mains supply. The Module is located in a 3m Semi-Anechoic Chamber; the antenna factors, cable loss and so on of the site as factors are calculated to correct the reading. During the measurement, the EUT is activated and controlled by the Wireless Router via a Common Antenna, and is set to operate under hopping-on test mode. For the Test Antenna: (a) In the frequency range of 9kHz to 30MHz, magnetic field is measured with Loop Test Antenna. The Test Antenna is positioned with its plane vertical at 1m distance from the EUT. The center of the Loop Test Antenna is 1m above the ground. During the measurement the Loop Test Antenna rotates about its vertical axis for maximum response at each azimuth about the EUT. (b) In the frequency range above 30MHz, Bi-Log Test Antenna (30MHz to 2GHz) and Horn Test Antenna (above 2GHz) are used. Test Antenna is 3m away from the EUT. Test Antenna height is varied from 1m to 4m above the ground to determine the maximum value of the field strength. The emission levels at both horizontal and vertical polarizations should be tested. B. Equipments List: Description Manufacturer Model Serial No. Cal. Date Cal. Due Spectrum Analyzer Agilent E4447A US62552411 2013.05.12 2014.05.11 Full-Anechoic Chamber Albatross 9m*6m*6m (n.a.) 2013.05.12 2014.05.11 Test Antenna - Bi-Log Schwarzbeck VULB 9163 9163-274 2013.05.12 2014.05.11 Test Antenna - Horn Schwarzbeck BBHA 9120D 9120D-963 2013.05.12 2014.05.11 Page 23 of 32

SZ13090014W02 Description Manufacturer Model Serial No. Cal. Date Cal. Due Test Antenna - Horn R&S HL050S7 71688 2013.05.12 2014.05.11 Test Antenna - Horn Schwarzbeck BBHA9170 9170-872 2013.05.12 2014.05.11 Test Antenna -Loop Schwarzbeck FMZB 1519 1519-022 2013.05.12 2014.05.11 2.7.3. Test Result According to ANSI C63.4 selection 4.2.2, because of peak detection will yield amplitudes equal to or greater than amplitudes measured with the quasi-peak (or average) detector, the measurement data from a spectrum analyzer peak detector will represent the worst-case results, if the peak measured value complies with the quasi-peak limit, it is unnecessary to perform an quasi-peak measurement. The measurement results are obtained as below: E [dBμV/m] =UR + AT + AFactor [dB]; AT =LCable loss [dB]-Gpreamp [dB] AT: Total correction Factor except Antenna UR: Receiver Reading Gpreamp: Preamplifier Gain AFactor: Antenna Factor at 3m During the test, the total correction Factor AT and AFactor were built in test software. Note: All radiated emission tests were performed in X, Y, Z axis direction. And only the worst axis test condition was recorded in this test report. 2.7.3.1. Test mode A. Test Plots for the Whole Measurement Frequency Range: Page 24 of 32

SZ13090014W02 Plots for Channel = 1 150DBuV No Frequency PeakAp QP-Limit AV-Limit Quasi-P Avera-P Result 1 84 K 48.76 DBuV 109.11 -- -- -- -- 2 27.66 M 49.66 DBuV 69.50 -- -- -- -- 130DBuV 110DBuV 90DBuV 70DBuV 1 2 50DBuV 30DBuV 10DBuV 9K10K 20K 30K 40K 50K60K70K80K 90K 100K 200K 300K 400K500K600K 700K 800K 900K 1M 2M 3M 4M 5M 6M 7M8M9M10M 20M 30M (Plot A.1: 9kHz to 30MHz) Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 172.718 39.16 37.11 39.05 N.A 43.5 N.A Horizontal PASS 288.828 38.26 N.A N.A N.A 46.0 N.A Horizontal PASS 970.973 32.16 N.A N.A N.A 54.0 N.A Horizontal PASS 5728.000 73.36 N.A N.A N.A N.A N.A Horizontal N.A 11448.878 43.11 N.A N.A 74.0 N.A 54.0 Horizontal PASS 15783.042 40.72 N.A N.A 74.0 N.A 54.0 Horizontal PASS (Plot A.2: Antenna Horizontal, 30MHz to 25GHz) Page 25 of 32

SZ13090014W02 Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 28403.998 46.18 N.A N.A 74.0 N.A 54.0 Horizontal PASS 39214.467 47.18 N.A N.A 74.0 N.A 54.0 Horizontal PASS (Plot A.3: Antenna Horizontal, 25GHz to 40GHz) Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 172.718 35.37 N.A N.A N.A 43.5 N.A Vertical PASS 358.978 23.79 N.A N.A N.A 46.0 N.A Vertical PASS 5784.000 71.70 N.A N.A N.A N.A N.A Vertical N.A 11448.878 45.08 N.A N.A 74.0 N.A 54.0 Vertical PASS 15728.180 40.49 N.A N.A 74.0 N.A 54.0 Vertical PASS (Plot A.4: Antenna Vertical, 30MHz to 25GHz) Page 26 of 32

SZ13090014W02 Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 28302.918 45.38 N.A N.A 74.0 N.A 54.0 Vertical PASS 38625.337 47.34 N.A N.A 74.0 N.A 54.0 Vertical PASS (Plot A.5: Antenna Vertical, 25GHz to 40GHz) Plot for Channel = 8 150DBuV No Frequency PeakAp QP-Limit AV-Limit Quasi-P Avera-P Result 1 69 K 52.13 DBuV 110.82 -- -- -- -- 2 27.66 M 49.76 DBuV 69.50 -- -- -- -- 130DBuV 110DBuV 90DBuV 70DBuV 1 2 50DBuV 30DBuV 10DBuV 9K10K 20K 30K 40K 50K60K70K80K 90K 100K 200K 300K 400K500K600K 700K 800K 900K 1M 2M 3M 4M 5M 6M 7M8M9M10M 20M 30M (Plot B.1: 9kHz to 30MHz) Page 27 of 32

SZ13090014W02 Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 172.718 39.80 35.77 39.07 N.A 43.5 N.A Horizontal PASS 288.828 38.46 N.A N.A N.A 46.0 N.A Horizontal PASS 358.978 34.97 N.A N.A N.A 46.0 N.A Horizontal PASS 5784.000 73.75 N.A N.A N.A N.A N.A Horizontal N.A 11558.603 45.42 N.A N.A 74.0 N.A 54.0 Horizontal PASS 15783.042 41.48 N.A N.A 74.0 N.A 54.0 Horizontal PASS (Plot B.2: Antenna Horizontal, 30MHz to 25GHz) Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 28142.214 46.13 N.A N.A 74.0 N.A 74.0 Horizontal PASS 34655.087 46.34 N.A N.A 74.0 N.A 74.0 Horizontal PASS (Plot B.3: Antenna Horizontal, 25GHz to 40GHz) Page 28 of 32

SZ13090014W02 Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 175.137 35.37 N.A N.A N.A 43.5 N.A Vertical PASS 358.978 24.13 N.A N.A N.A 46.0 N.A Vertical PASS 5754.000 72.68 N.A N.A N.A N.A N.A Vertical N.A 11558.603 46.86 N.A N.A 74.0 N.A 54.0 Vertical PASS 15728.180 42.17 N.A N.A 74.0 N.A 54.0 Vertical PASS (Plot B.4: Antenna Vertical, 30MHz to 25GHz) Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 28239.177 45.73 N.A N.A 74.0 N.A 54.0 Vertical PASS 38760.559 48.64 N.A N.A 74.0 N.A 54.0 Vertical PASS (Plot B.5: Antenna Vertical, 30MHz to 25GHz) Page 29 of 32

SZ13090014W02 Plot for Channel = 16 150DBuV No Frequency PeakAp QP-Limit AV-Limit Quasi-P Avera-P Result 1 84 K 51.17 DBuV 109.11 -- -- -- -- 2 27.66 M 49.12 DBuV 69.50 -- -- -- -- 130DBuV 110DBuV 90DBuV 70DBuV 1 2 50DBuV 30DBuV 10DBuV 9K10K 20K 30K 40K 50K60K70K80K 90K 100K 200K 300K 400K500K600K 700K 800K 900K 1M 2M 3M 4M 5M 6M 7M8M9M10M 20M 30M (Plot C.1: 9kHz to 30MHz) Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 172.718 39.79 36.48 38.74 N.A 43.5 N.A Horizontal PASS 288.828 38.92 N.A N.A N.A 46.0 N.A Horizontal PASS 1937.656 43.73 N.A N.A 74.0 N.A 54.0 Horizontal PASS 5852.868 70.65 N.A N.A N.A N.A N.A Horizontal N.A 11668.329 44.91 N.A N.A 74.0 N.A 54.0 Horizontal PASS (Plot C.2: Antenna Horizontal, 30MHz to 25GHz) Page 30 of 32

SZ13090014W02 Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 29561.359 46.61 N.A N.A 74.0 N.A 54.0 Horizontal PASS 38621.596 47.22 N.A N.A 74.0 N.A 54.0 Horizontal PASS (Plot C.3: Antenna Horizontal, 25GHz to 40GHz) Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 175.137 35.70 33.52 35.14 N.A 43.5 N.A Vertical PASS 358.978 22.86 N.A N.A N.A 46.0 N.A Vertical PASS 5852.868 73.26 N.A N.A N.A N.A N.A Vertical N.A 11668.329 45.96 N.A N.A 74.0 N.A 54.0 Vertical PASS 15728.180 41.00 N.A N.A 74.0 N.A 54.0 Vertical PASS (Plot C.4: Antenna Vertical, 30MHz to 25GHz) Page 31 of 32

SZ13090014W02 Fre. (MHz) Pk QP AV Limit-PK Limit-QP Limit-AV Antenna Verdict 28437.880 46.82 N.A N.A 74.0 N.A 54.0 Vertical PASS 39848.778 47.54 N.A N.A 74.0 N.A 54.0 Vertical PASS (Plot C.5: Antenna Vertical, 25GHz to 40GHz) ** END OF REPORT ** Page 32 of 32


Document Created: 2019-10-31 04:37:40
Document Modified: 2019-10-31 04:37:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC