Test Report

FCC ID: SRDRTR5X

Test Report

Download: PDF
FCCID_1384237

849 NW State Road 45 Newberry, FL 32669 USA Ph: 888.472.2424 or 352.472.5500 Fax: 352.472.2030 Email: info@timcoengr.com Website: www.timcoengr.com FCC PART 15.249 CLASS II PERMISSIVE CHANGE TEST REPORT UNLICENSED INTENTIONAL RADIATOR Applicant T&D CORPORATION Address 817-1 SHIMADACHI MATSUMOTO 390-0852 JAPAN FCC ID SRDRTR5X Product Description 900 MHz DATA RECORDER Date Sample Received 10/1/2010 Date Tested 10/21/2010 Tested By Nam Nguyen Approved By Mario de Aranzeta Report Number 2342UT10TestReport.doc Test Results PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. Certificate # 0955-01

TABLE OF CONTENT GENERAL REMARKS ........................................................................................................................... 3 GENERAL INFORMATION .................................................................................................................... 4 EMC EQUIPMENT LIST........................................................................................................................ 5 TEST PROCEDURES ............................................................................................................................ 6 RADIATION INTERFERENCE ............................................................................................................... 7 OCCUPIED BANDWIDTH ..................................................................................................................... 8 BAND EDGE COMPLIANCE ............................................................................................................... 10 POWER LINE CONDUCTED INTERFERENCE .................................................................................... 13 APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 2 of 13 Mdea 9.20.2007

GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Mario de Aranzeta C.E.T. Compliance Engineer/ Lab. Supervisor Date: 10/29/2010 APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 3 of 13 Mdea 9.20.2007

GENERAL INFORMATION DUT Specification The test results relate only to the items tested. Applicable Standard Part 15.249 DUT Description 900 MHz DATA RECORDER FCC ID SRDRTR5X Operating Frequency TX/RX: 902.28 – 927.64 MHz DUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable Antenna Connector FCC Rules require that the antenna connector be unique. Timco Engineering Inc. located at 849 NW State Road 45 Test Facility Newberry, FL 32669 USA. Temperature: 26ºC Test Conditions Relative humidity: 50% Test Exercise The DUT was placed in continuous transmit mode of operation. Test Supporting Equipment Supporting Device Manufacturer Model / FCC ID Serial Number N/A APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 4 of 13 Mdea 9.20.2007

EMC EQUIPMENT LIST Serial Cal/Char Device Manufacturer Model Due Date Number Date 3-Meter Semi- Listed Anechoic Panashield N/A N/A 3/10/12 3/10/10 Chamber CAL AC Voltmeter HP 400FL 2213A14499 3/23/11 3/23/09 Antenna: Electro- CHAR TDA-30/1-4 153 6/10/11 Dipole Kit Metrics 6/10/09 Frequency CAL HP 5385A 3242A07460 5/26/11 Counter 5/26/09 Hygro- CAL Extech 445703 0602 1/30/11 Thermometer 1/30/09 Modulation CAL HP 8901A 3435A06868 5/26/11 Analyzer 5/26/09 Digital CAL Fluke FLUKE-77-3 79510405 5/18/11 Multimeter 5/18/09 Analyzer Tan CAL Tower HP 8449B-H02 3008A00372 11/21/11 11/21/09 Preamplifier Analyzer Tan CAL Tower Quasi- HP 85650A 3303A01690 11/22/11 11/22/09 Peak Adapter Analyzer Tan CAL Tower RF HP 85685A 3221A01400 11/21/11 11/21/09 Preselector Analyzer Tan Tower 8566B Opt 3138A07786 CAL HP 11/24/11 Spectrum 462 3144A20661 11/24/09 Analyzer Temperature Tenney CHAR TTRC 11717-7 4/25/12 Chamber Engineering 4/25/10 APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 5 of 13 Mdea 9.20.2007

TEST PROCEDURES Radiation Interference: ANSI C63.4-2003 using a spectrum analyzer, a preselector, a quasi- peak adapter, and an appropriate antenna. The analyzer was calibrated in dB above a microvolt at the output of the antenna. The resolution bandwidth was 100 kHz with an appropriate sweep speed and the video bandwidth was 300 kHz up to 1 GHz and 1 MHz with a video BW of 3 MHz above 1 GHz. When an emission was found, the table was rotated to produce the maximum signal strength. The antenna was placed in both the horizontal and vertical planes and the worse case emissions were reported. The spectrum was searched to at least the tenth (10) harmonic of the fundamental. Formula Of Conversion Factors: The field strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units of dBuV) to the antenna correction factor supplied by the antenna manufacturer. The antenna correction factors are stated in terms of dB. The gain of the preselector was accounted for in the spectrum analyzer meter reading. Example: Freq (MHz) Meter Reading + ACF + CL = FS 33 20 dBuV + 10.36 dB + 0.5 = 30.86 dBuV/m @ 3m Power Line Conducted Interference: The procedure used was ANSI C63.4-2003 using a 50uH LISN. Both lines were observed. The bandwidth of the spectrum analyzer was 10kHz with an appropriate sweep speed. The spectrum was scanned from 0.15 to 30 MHz. Occupied Bandwidth: A small sample of the transmitter output was fed into the spectrum analyzer and the attached plot was printed. The vertical scale is set to -10 dBm per division. ANSI C63.4-2003 10.1 Measurement Procedures: The DUT was placed on a table 80 cm high and with dimensions of 1m by 1.5m. The DUT was placed in the center of the table (1.5m side). The table used for radiated measurements is capable of continuous rotation. When an emission was found, the table was rotated to produce the maximum signal strength. At this point, the antenna was raised and lowered from 1m to 4m. The antenna was placed in both the horizontal and vertical planes. Emissions attenuated more than 20 dB below the permissible value are not reported. APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 6 of 13 Mdea 9.20.2007

RADIATION INTERFERENCE Rules Part No.: 15.249, 15.209 Requirements: Frequency Limits Part 15.209 9 to 490 kHz 2400/F (kHz) µV/m @ 300 meters 490 to 1705 kHz 24000/F (kHz) µV/m @ 30 meters 1705 kHz to 30 MHz 29.54 dBµV/m @ 30 meters 30 – 88 40.0 dBµV/m @ 3 meters 80 – 216 43.5 dBµV/m @ 3 meters 216 – 960 46.0 dBµV/m @ 3 meters Above 960 54.0 dBµV/m @ 3 meters Part 15.249 Fundamental 902 – 928 MHz 94.0 dBµV/m @ 3 meters Fundamental 2.4 – 2.4835 MHz 94.0 dBµV/m @ 3 meters Harmonics 54.0 dBµV/m @ 3 meters Test Data: Tuned Emission Meter Ant. Coax Correction Field Margin Frequency Frequency Reading Polarity Loss Factor Strength dB MHz MHz dBuV dB dB/m dBuV/m 902.3 902.28 59.1 V 1.95 22.68 83.73 10.27 902.3 902.28 65.4 H 1.95 23.32 90.67 3.33 902.3 1,804.56 19.6 V 2.74 29.95 52.29 1.71 902.3 1,804.56 20.2 H 2.74 29.95 52.89 1.11 902.3 2,706.84 15.8 H 3.39 32.54 51.73 2.27 902.3 2,706.84 16.7 V 3.39 32.54 52.63 1.37 902.3 3,609.12 4.4 V 4.15 32.97 41.52 12.48 902.3 3,609.12 5.6 H 4.15 32.97 42.72 11.28 914.1 914.08 59.0 V 1.97 22.60 83.57 10.43 914.1 914.08 62.4 H 1.97 23.36 87.73 6.27 914.1 1,828.15 16.7 V 2.76 30.10 49.56 4.44 914.1 1,828.15 20.9 H 2.76 30.10 53.76 0.24 914.1 2,742.23 15.5 V 3.42 32.55 51.47 2.53 914.1 2,742.23 16.7 H 3.42 32.55 52.67 1.33 914.1 3,656.31 3.9 V 4.19 33.05 41.14 12.86 914.1 3,656.31 5.5 H 4.19 33.05 42.74 11.26 927.1 927.05 59.1 V 1.99 22.67 83.76 10.24 927.1 927.05 63.4 H 1.99 23.44 88.83 5.17 927.1 1,854.11 16.1 V 2.78 30.27 49.15 4.85 927.1 1,854.11 18.7 H 2.78 30.27 51.75 2.25 927.1 2,781.16 13.9 V 3.45 32.56 49.91 4.09 927.1 2,781.16 17.3 H 3.45 32.56 53.31 0.69 927.1 3,708.21 4.3 H 4.24 33.13 41.67 12.33 927.1 3,708.21 6.9 V 4.24 33.13 44.27 9.73 APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 7 of 13 Mdea 9.20.2007

OCCUPIED BANDWIDTH Rules Part No.: 15.249 (d) Requirements: The field strength of any emissions appearing outside the bandedges and up to 10 kHz above and below the band edges shall be attenuated at least 50 dB below the level of the carrier or to the general limits of 15.249. Test Data: The 20 dB bandwidth APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 8 of 13 Mdea 9.20.2007

MKR A 249 kHz /73 REF —40.0 dBr ATTEN @ dB +8 dB —©.20 dB 10 dB/ OFFSET —20.0 dB MARKER > 249 kz —@.20| dB CENTER 914.08 MHz SPAN 1.50 MHz RES BW 100 kHz UBW 100| kHz SHP 20.0 risec

BAND EDGE COMPLIANCE Rules Part No.: 15.249 (d) Requirements: 40 dBc or in the case of restricted bands 54 dBuV/m. Test Data: Lower bandedge Tuned Emission Meter Ant. Coax Correction Field Frequency Frequency Reading Polarity Loss Factor Strength Margin MHz MHz dBuV V/H dB dB/m dBuV/m dB 902.28 902 31.5 H 1.95 23.32 56.77 -2.77(Peak) 902.28 902 14.9 H 1.95 23.32 40.17 13.83(Avg) Upper bandedge Tuned Emission Meter Ant. Coax Correction Field Frequency Frequency Reading Polarity Loss Factor Strengt Margin MHz MHz dBuV V/H dB dB/m h dB dBuV/m 927.05 928.25 13.4 H 1.99 23.47 38.86 15.14 (Peak) 927.05 928.25 -1.9 H 1.99 23.47 23.56 30.44 (Avg) APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 10 of 13 Mdea 9.20.2007

Lower bandedge Peak Plot Average Plot APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 11 of 13 Mdea 9.20.2007

Upper bandedge Peak Plot Average Plot APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 12 of 13 Mdea 9.20.2007

POWER LINE CONDUCTED INTERFERENCE Rules Part No.: 15.207 Requirements: Frequency Quasi Peak Limits Average Limits (MHz) (dBµV) (dBuV) 0.15 – 0.5 66 – 56 56 – 46 0.5 – 5.0 56 46 5.0 – 30 60 50 Test Data: Not applicable. Battery operated device. APPLICANT: T&D CORPORATION FCC ID: SRDRTR5X REPORT: T\T&D CORP_SRD\2342UT10\2342UT10TestReport.doc Page 13 of 13 Mdea 9.20.2007


Document Created: 2010-11-30 16:28:09
Document Modified: 2010-11-30 16:28:09
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC