Test Report

FCC ID: SQGBT900US

Test Report

Download: PDF
FCCID_2496696

FCC Test Report FCC ID : SQGBT900US Equipment : Intelligent BT4.0 Dual Mode USB Dongle Model No. : BT900-US Brand Name : Laird Technologies Applicant : Laird Technologies Address : 11160 Thompson Ave., Lenexa, Kansas 66219, USA Standard : 47 CFR FCC Part 15.247 Received Date : Dec. 10, 2014 Tested Date : Dec. 11 ~ Dec. 15, 2014 We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by: Gary Chang / Manager Ty: XXX Report No.: FR442807-01AE Page : 1 of 33 Report Version: Rev. 01

Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information.............................................................................................................................................. 5 1.2 Local Support Equipment List ................................................................................................................ 7 1.3 Test Setup Chart .................................................................................................................................... 7 1.4 Test Equipment List and Calibration Data .............................................................................................. 8 1.5 Test Standards ....................................................................................................................................... 9 1.6 Measurement Uncertainty ...................................................................................................................... 9 2 TEST CONFIGURATION .....................................................................................................................10 2.1 Testing Condition .................................................................................................................................10 2.2 The Worst Test Modes and Channel Details .......................................................................................10 3 TRANSMITTER TEST RESULTS........................................................................................................11 3.1 Conducted Emissions ...........................................................................................................................11 3.2 6dB and Occupied Bandwidth ..............................................................................................................14 3.3 RF Output Power ..................................................................................................................................17 3.4 Power Spectral Density ........................................................................................................................19 3.5 Emissions in Restricted Frequency Bands ...........................................................................................21 3.6 Emissions in non-restricted Frequency Bands .....................................................................................31 4 TEST LABORATORY INFORMATION ...............................................................................................33 Report No.: FR442807-01AE Page : 2 of 33 Report Version: Rev. 01

Release Record Report No. Version Description Issued Date FR442807-01AE Rev. 01 Initial issue Jan. 07, 2015 Report No.: FR442807-01AE Page : 3 of 33 Report Version: Rev. 01

Summary of Test Results FCC Rules Test Items Measured Result [dBuV]: 4.926MHz 15.207 AC Power Line Conducted Emissions Pass 35.33 (Margin -10.67dB) - AV 15.247(d) [dBuV/m at 3m]: 7320.00MHz Radiated Emissions Pass 15.209 50.22 (Margin -3.78dB) - AV 15.247(b)(3) Maximum Output Power Power [dBm]: 8.17 Pass 15.247(a)(2) 6dB Bandwidth Meet the requirement of limit Pass 15.247(e) Power Spectral Density Meet the requirement of limit Pass 15.203 Antenna Requirement Meet the requirement of limit Pass Report No.: FR442807-01AE Page : 4 of 33 Report Version: Rev. 01

1 General Description 1.1 Information 1.1.1 Specification of the Equipment under Test (EUT) RF General Information Frequency Range Bluetooth Ch. Freq. (MHz) Channel Number Data Rate (MHz) Mode 2400-2483.5 V4.0 LE 2402-2480 0-39 [40] 1 Mbps Note 1: Bluetooth LE (Low energy) uses GFSK modulation. 1.1.2 Antenna Details Ant. No. Type Gain (dBi) Connector Remark 1 Chip 0.5 --- --- 1.1.3 Power Supply Type of Equipment under Test (EUT) Power Supply Type 5Vdc from host 1.1.4 Accessories N/A Report No.: FR442807-01AE Page : 5 of 33 Report Version: Rev. 01

1.1.5 Channel List Frequency band (MHz) 2400~2483.5 Frequency Frequency Frequency Frequency Channel Channel Channel Channel (MHz) (MHz) (MHz) (MHz) 37 2402 9 2422 18 2442 28 2462 0 2404 10 2424 19 2444 29 2464 1 2406 38 2426 20 2446 30 2466 2 2408 11 2428 21 2448 31 2468 3 2410 12 2430 22 2450 32 2470 4 2412 13 2432 23 2452 33 2472 5 2414 14 2434 24 2454 34 2474 6 2416 15 2436 25 2456 35 2476 7 2418 16 2438 26 2458 36 2478 8 2420 17 2440 27 2460 39 2480 1.1.6 Test Tool and Duty Cycle Test tool Blue Test3, Version: 2.5.8.667 Duty cycle of test signal (%) 66.97% Duty Factor (dB) 1.74 1.1.7 Power Setting Test Frequency (MHz) Modulation Mode 2402 2440 2480 GFSK/1Mbps Default Default Default Report No.: FR442807-01AE Page : 6 of 33 Report Version: Rev. 01

1.2 Local Support Equipment List Support Equipment List No. Equipment Brand Model S/N Signal cable / Length (m) Latitude 1 Notebook DELL B6FV9T1 --- E5420 1.3 Test Setup Chart Test Setup Diagram Report No.: FR442807-01AE Page : 7 of 33 Report Version: Rev. 01

1.4 Test Equipment List and Calibration Data Test Item Conducted Emission Test Site Conduction room 1 / (CO01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until EMC Receiver R&S ESCS 30 100169 Oct. 17, 2014 Oct. 16, 2015 LISN SCHWARZBECK Schwarzbeck 8127 8127-667 Nov. 17, 2014 Nov. 16, 2015 LISN SCHWARZBECK Schwarzbeck 8127 8127-666 Nov. 26, 2014 Nov. 25, 2015 (Support Unit) RF Cable-CON Woken CFD200-NL CFD200-NL-001 Apr. 23, 2014 Apr. 22, 2015 50 ohm terminal NA 50 04 Apr. 18, 2014 Apr. 17, 2015 (Support Unit) Measurement AUDIX e3 6.120210k NA NA Software Note: Calibration Interval of instruments listed above is one year. Test Item Radiated Emission Test Site 966 chamber 3 / (03CH03-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer Agilent N9010A MY53400091 Sep. 16, 2014 Sep. 15, 2015 Receiver Agilent N9038A MY53290044 Oct. 21, 2014 Oct. 20, 2015 Bilog Antenna SCHWARZBECK VULB9168 VULB9168-562 Feb. 07, 2014 Feb. 06, 2015 Horn Antenna SCHWARZBECK BBHA 9120 D BBHA 9120 D 1206 Feb. 20, 2014 Feb. 19, 2015 1G-18G Horn Antenna SCHWARZBECK BBHA 9170 BBHA 9170517 Nov. 10, 2014 Nov. 09, 2015 18G-40G Preamplifier EMC EMC02325 980187 Sep. 26, 2014 Sep. 25, 2015 Preamplifier Agilent 83017A MY53270014 Sep. 17, 2014 Sep. 16, 2015 Preamplifier EMC EMC184045B 980192 Aug. 26, 2014 Aug. 25, 2015 RF cable-3M HUBER+SUHNER SUCOFLEX104 MY22620/4 Feb. 19, 2014 Feb. 18, 2015 RF cable-8M HUBER+SUHNER SUCOFLEX104 MY22601/4 Feb. 19, 2014 Feb. 18, 2015 RF cable-1M HUBER+SUHNER SUCOFLEX104 MY22624/4 Feb. 19, 2014 Feb. 18, 2015 LF cable-0.8M EMC EMC8D-NM-NM-800 EMC8D-NM-NM-800-001 Feb. 17, 2014 Feb. 16, 2015 LF cable-3M EMC EMC8D-NM-NM-3000 131103 Feb. 17, 2014 Feb. 16, 2015 LF cable-13M EMC EMC8D-NM-NM-13000 131104 Feb. 17, 2014 Feb. 16, 2015 Loop Antenna R&S HFH2-Z2 100330 Nov. 10, 2014 Nov. 09, 2015 Measurement AUDIX e3 6.120210g NA NA Software Note: Calibration Interval of instruments listed above is one year. Report No.: FR442807-01AE Page : 8 of 33 Report Version: Rev. 01

@ Infernational Certification Corp. Test Item RF Conducted Test Site (THO1—WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Spectrum Analyzer R&S FSV40 101063 Feb. 17, 2014 Feb. 16, 2015 Power Meter Anritsu ML2495A 1241002 Sep. 29, 2014 Sep. 28, 2015 Power Sensor Anritsu MA2Z411B 1207366 Sep. 29, 2014 Sep. 28, 2015 Measurement Software Sporton Sporton_1 1.3.30 NA NA Note: Calibration Interval of instruments listed above is one year. 1.5 Test Standards According to the specification of EUT, the EUT must comply with following standards and KDB documents. 47 CFR FCC Part 15.247 ANSI C63.10—2013 FCC KDB 558074 D01 DTS Meas Guidance v03r02 1.6 Measurement Uncertainty I1SO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Measurement Uncertainty Parameters Uncertainty Bandwidth +34.134 Hz Conducted power +0.808 dB Frequency error +34.134 Hz Temperature +0.6 °C Conducted emission +2.670 dB AC conducted emission +2.92 dB Radiated emission < 1GHz +3.26 dB Radiated emission > 1GHz +4.94 dB Report No.: FR442807—01AE Page : 9 of 33 Report Version: Rev. 01

C Infernational Certification Corp. 2 Test Configuration 2.1 Testing Condition Test Item Test Site Ambient Condition Tested By AC Conduction COo1—ws 19°C /67% Peter Lin Radiated Emissions O3CHO3—WS 21°C / 63% Lance Xiao RF Conducted THO1—wWS 23°C / 62% Brad Wu » FCC site registration No.: 390588 » IC site registration No.: 10807C—1 2.2 The Worst Test Modes and Channel Details Test item mede *"misy®"" "ops)_| contigwation AC Power Line Conducted Emissions GFSK 2480 1Mbps Radiated Emissions 1GHz GFSK 2480 1Mbps Radiated Emissions > 1GHz GFSK 2402, 2440, 2480 1Mbps Maximum Output Power 6dB bandwidth GFSK 2402, 2440, 2480 1Mbps Power spectral density Report No.: FR442807—01AE Page : 10 of 33 Report Version: Rev. 01

3 Transmitter Test Results 3.1 Conducted Emissions 3.1.1 Limit of Conducted Emissions Conducted Emissions Limit Frequency Emission (MHz) Quasi-Peak Average 0.15-0.5 66 - 56 * 56 - 46 * 0.5-5 56 46 5-30 60 50 Note 1: * Decreases with the logarithm of the frequency. 3.1.2 Test Procedures 1. The device is placed on a test table, raised 80 cm above the reference ground plane. The vertical conducting plane is located 40 cm to the rear of the device. 2. The device is connected to line impedance stabilization network (LISN) and other accessories are connected to other LISN. Measured levels of AC power line conducted emission are across the 50 Ω LISN port. 3. AC conducted emission measurements is made over frequency range from 150 kHz to 30 MHz. 4. This measurement was performed with AC 120V/60Hz 3.1.3 Test Setup Report No.: FR442807-01AE Page : 11 of 33 Report Version: Rev. 01

3.1.4 Test Result of Conducted Emissions Modulation Mode GFSK Test Freq. (MHz) 2480 Power Phase Line Test Configuration 1 Note 1: Level (dBuV) = Read Level (dBuV) + LISN Factor (dB) + Cable Loss (dB). 2: Over Limit (dB) = Level (dBuV) – Limit Line (dBuV). Report No.: FR442807-01AE Page : 12 of 33 Report Version: Rev. 01

Modulation Mode GFSK Test Freq. (MHz) 2480 Power Phase Neutral Test Configuration 1 Note 1: Level (dBuV) = Read Level (dBuV) + LISN Factor (dB) + Cable Loss (dB). 2: Over Limit (dB) = Level (dBuV) – Limit Line (dBuV). Report No.: FR442807-01AE Page : 13 of 33 Report Version: Rev. 01

3.2 6dB and Occupied Bandwidth 3.2.1 Limit of 6dB Bandwidth The minimum 6dB bandwidth shall be at least 500 kHz. 3.2.2 Test Procedures 1. Set c resolution bandwidth (RBW) = 100 kHz, Video bandwidth = 300 kHz. 2. Detector = Peak, Trace mode = max hold. 3. Sweep = auto couple, Allow the trace to stabilize. 4. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower) that are attenuated by 6dB relative to the maximum level measured in the fundamental emission. 5. Use OBW measurement function of spectrum analyzer to measure occupied bandwidth. 3.2.3 Test Setup Report No.: FR442807-01AE Page : 14 of 33 Report Version: Rev. 01

3.2.4 Test Result of 6dB and Occupied Bandwidth Freq. (MHz) 6dB Bandwidth (kHz) Limit (kHz) 2402 696 500 2440 696 500 2480 696 500 Worst Plots Report No.: FR442807-01AE Page : 15 of 33 Report Version: Rev. 01

Freq. (MHz) 99% Occupied Bandwidth (MHz) 2402 1.02 2440 1.02 2480 1.02 Worst Plots Report No.: FR442807-01AE Page : 16 of 33 Report Version: Rev. 01

3.3 RF Output Power 3.3.1 Limit of RF Output Power Conducted power shall not exceed 1Watt. Antenna gain <= 6dBi, no any corresponding reduction is in output power limit. Antenna gain > 6dBi Non Fixed, point to point operations. The conducted output power from the intentional radiator shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dB Fixed, point to point operations Systems operating in the 2400–2483.5 MHz band that are used exclusively for fixed, point-to-point Operations, maximum peak output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. Systems operating in the 5725–5850 MHz band that are used exclusively for fixed, point-to-point operations ,no any corresponding reduction is in transmitter peak output power 3.3.2 Test Procedures Maximum Peak Conducted Output Power Spectrum analyzer 1. Set RBW = 1MHz, VBW = 3MHz, Detector = Peak. 2. Sweep time = auto, Trace mode = max hold, Allow trace to fully stabilize. 3. Use the spectrum analyzer channel power measurement function with the band limits set equal to the DTS bandwidth edges. Power meter 1. A broadband Peak RF power meter is used for output power measurement. The video bandwidth of power meter is greater than DTS bandwidth of EUT. If duty cycle of test signal is not 100 %, trigger and gating function of power meter will be enabled to capture transmission burst for measuring output power. Maximum Conducted Average Output Power ( For reference only) Power meter 1. A broadband Average RF power meter is used for output power measurement. The video bandwidth of power meter is greater than DTS bandwidth of EUT. If duty cycle of test signal is not 100 %, trigger and gating function of power meter will be enabled to capture transmission burst for measuring output power. 3.3.3 Test Setup Report No.: FR442807-01AE Page : 17 of 33 Report Version: Rev. 01

3.3.4 Test Result of Maximum Output Power Freq. (MHz) Peak Conducted Power (dBm) Limit (dBm) 2402 5.84 30 2440 7.14 30 2480 8.17 30 Freq. (MHz) Average Conducted Power (dBm) Limit (dBm) 2402 5.28 30 2440 6.68 30 2480 7.89 30 Note: Average power is for reference only. Report No.: FR442807-01AE Page : 18 of 33 Report Version: Rev. 01

3.4 Power Spectral Density 3.4.1 Limit of Power Spectral Density Power spectral density shall not be greater than 8 dBm in any 3 kHz band. 3.4.2 Test Procedures Maximum peak conducted output power was used to demonstrate compliance to the fundamental output power limit. 1. Set the RBW = 3kHz, VBW = 10kHz. 2. Detector = Peak, Sweep time = auto couple. 3. Trace mode = max hold, allow trace to fully stabilize. 4. Use the peak marker function to determine the maximum amplitude level. Maximum (average) conducted output power was used to demonstrate compliance to the fundamental output power limit. 1. Set the RBW = 100kHz, VBW = 300 kHz. 2. Detector = RMS, Sweep time = auto couple. 3. Set the sweep time to: ≥ 10 x (number of measurement points in sweep) x (maximum data rate per stream). 4. Perform the measurement over a single sweep. 5. Use the peak marker function to determine the maximum amplitude level.\ 3.4.3 Test Setup Report No.: FR442807-01AE Page : 19 of 33 Report Version: Rev. 01

3.4.4 Test Result of Power Spectral Density Freq. (MHz) Power Spectral Density (dBm / 3kHz) Limit (dBm) 2402 -10.67 8 2440 -9.17 8 2480 -7.93 8 Worst Plots Report No.: FR442807-01AE Page : 20 of 33 Report Version: Rev. 01

C Infernational Certification Corp. 3.5 Emissions in Restricted Frequency Bands 3.5.1 Limit of Emissions in Restricted Frequency Bands Restricted Band Emissions Limit Frequency Range (MHz)| Field Strength (uV/m) |Field Strength (dBuV/m)| Measure Distance (m) 0.009~0.490 2400/F(kHz) 48.5 — 13.8 300 0.490~1.705 24000/F(kHz) 33.8 — 23 30 1.705~30.0 30 29 30 30~88 100 40 3 88~216 150 43.5 3 216~960 200 46 3 Above 960 500 54 3 Note 1: Qusai—Peak value is measured for frequency below 1GHz except for 9—90 kHz, 110—490 kHz frequency band. Peak and average value are measured for frequency above 1GHz. The limit on average radio frequency emission is as above table. The limit on peak radio frequency emissions is 20 dB above the maximum permitted average emission limit Note 2: Measurements may be performed at a distance other than what is specified provided. When performing measurements at a distance other than that specified, the results shall be extrapolated to the specified distance using an extrapolation factor as below, Frequency at or above 30 MHz: 20 dB/decade Frequency below 30 MHz: 40 dB/decade. 3.5.2 Test Procedures 1. Measurement is made at a semi—anechoic chamber that incorporates a turntable allowing a EUT rotation of 360°. A continuously—rotating, remotely—controlled turntable is installed at the test site to support the EUT and facilitate determination of the direction of maximum radiation for each EUT emission frequency. For emissions testing at or below 1 GHz, the table height is 80 cm above the reference ground plane. For emission measurements above 1 GHz, the table height is 1.5 m 2. Measurement is made with the antenna positioned in both the horizontal and vertical planes of polarization. The measurement antenna is varied in height (1m ~4m) above the reference ground plane to obtain the maximum signal strength. Distance between EUT and antenna is 3 m. 3. This investigation is performed with the EUT rotated 360°, the antenna height scanned between 1 m and 4 m, and the antenna rotated to repeat the measurements for both the horizontal and vertical antenna polarizations. Note: 1. 120kHz measurement bandwidth of test receiver and Quasi—peak detector is for radiated emission below 1GHz. 2. RBW=1MHz, VBW=3MHz and Peak detector is for peak measured value of radiated emission above 1GHz. 3. RBW=1MHz, VBW=1/T and Peak detector is for average measured value of radiated emission above 1GHz. Report No.: FR442807—01AE Page : 21 of 33 Report Version: Rev. 01

3.5.3 Test Setup Radiated Emissions below 1 GHz Radiated Emissions above 1 GHz Report No.: FR442807-01AE Page : 22 of 33 Report Version: Rev. 01

3.5.4 Transmitter Radiated Unwanted Emissions (Below 1GHz) Modulation GFSK Test Freq. (MHz) 2480 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Note 3: All spurious emissions below 30MHz are more than 20 dB below the limit. Report No.: FR442807-01AE Page : 23 of 33 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2480 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Note 3: All spurious emissions below 30MHz are more than 20 dB below the limit. Report No.: FR442807-01AE Page : 24 of 33 Report Version: Rev. 01

3.5.5 Transmitter Radiated Unwanted Emissions (Above 1GHz) for GFSK Modulation GFSK Test Freq. (MHz) 2402 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR442807-01AE Page : 25 of 33 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2402 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR442807-01AE Page : 26 of 33 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2440 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR442807-01AE Page : 27 of 33 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2440 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR442807-01AE Page : 28 of 33 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2480 Polarization Horizontal Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR442807-01AE Page : 29 of 33 Report Version: Rev. 01

Modulation GFSK Test Freq. (MHz) 2480 Polarization Vertical Note 1: Emission Level (dBuV/m) = SA Reading (dBuV/m) + Factor* (dB) *Factor includes antenna factor , cable loss and amplifier gain Note 2: Margin (dB) = Emission level (dBuV/m) – Limit (dBuV/m). Report No.: FR442807-01AE Page : 30 of 33 Report Version: Rev. 01

3.6 Emissions in non-restricted Frequency Bands 3.6.1 Emissions in non-restricted frequency bands limit Peak power in any 100 kHz bandwidth outside of the authorized frequency band shall be attenuated by at least 20 dB relative to the maximum in-band peak PSD level in 100 kHz 3.6.2 Test Procedures Reference level measurement 1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto 2. Trace = max hold , Allow Trace to fully stabilize 3. Use the peak marker function to determine the maximum PSD level Emission level measurement 1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto 2. Trace = max hold , Allow Trace to fully stabilize 3. Scan Frequency range is up to 26.5GHz 4. Use the peak marker function to determine the maximum amplitude level 3.6.3 Test Setup Transmitter Radiated Bandedge Emissions Report No.: FR442807-01AE Page : 31 of 33 Report Version: Rev. 01

TX Freq 2402MHz / 30MHz~25GHz (down 20dBc) TX Freq 2440MHz / 30MHz~25GHz (down 20dBc) TX Freq 2480MHz / 30MHz~25GHz (down 20dBc) Report No.: FR442807-01AE Page : 32 of 33 Report Version: Rev. 01

C Infernational Certification Corp. 4 Test laboratory information Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and one of the widest certification extents in the business. International Certification Corp, it is our definitive objective is to institute long term, trust—based associations with our clients. The expectation we set up with our clients is based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff. Our Test sites are located at Linkou District and Kwei Shan Hsiang. Location map can be found on our website http://www.icertifi.com.tw. Linkou Kwei Shan Kwei Shan Site II Tel: 886—2—2601—1640 Tel: 886—3—271—8666 Tel: 886—3—271—8640 No. 30—2, Ding Fwu Tsuen, Lin Kou No. 3—1, Lane 6, Wen San 3rd No. 14—1, Lane 19, Wen San 3rd District, New Taipei City, Taiwan, St., Kwei Shan Hsiang, Tao Yuan St., Kwei Shan Hsiang, Tao Yuan R.0.C. Hsien 333, Taiwan, R.0.C. Hsien 333, Taiwan, R.0.C. If you have any suggestion, please feel free to contact us as below information Tel: 886—3—271—8666 Fax: 886—3—318—0155 Email: ICC_Service@icertifi.com.tw ==END= Report No.: FR442807—01AE Page : 33 of 33 Report Version: Rev. 01


Document Created: 2019-11-01 10:58:00
Document Modified: 2019-11-01 10:58:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC