Users Manual

FCC ID: SLE-WAPN008-1

Users Manual

Download: PDF
FCCID_4497917

Moxa 2.4/4.9/5 GHz WAPN008-1 User’s Manual www.moxa.com First Edition, May 2019  2019 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.

WAPN008-1 User’s Manual The hardware and software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright  2019 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks MOXA is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time. Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Technical Support Contact Information www.moxa.com/support Moxa Americas: Moxa China (Shanghai office): Toll-free: 1-888-669-2872 Toll-free: 800-820-5036 Tel: +1-714-528-6777 Tel: +86-21-5258-9955 Fax: +1-714-528-6778 Fax: +86-10-6872-3958 Moxa Europe: Moxa Asia-Pacific: Tel: +49-89-3 70 03 99-0 Tel: +886-2-8919-1230 Fax: +49-89-3 70 03 99-99 Fax: +886-2-8919-1231

Table of Contents Chapter 1 Introduction Overview Specification Chapter 2 Getting Started Module Layout Block Diagram Hardware Installation Software Installation

WAPN008-1 User’s Manual Introduction 1 Chapter 1 Introduction The following topics are covered in this chapter:  Overview  Specifications

WAPN008-1 User’s Manual Introduction Overview WAPN008-1 PCI module is designed to provide wireless communication for Moxa industrial wireless products. It communicates via 2.4 GHz/4.9 GHz/5 GHz channels. The WAPN008-1 uses the AR9344 SoC Wireless chipset from Atheros. Specification Features WAPN008-1 Chipset Atheros AR9344 security engine - 64-bit and 128-bit WEP encryption, WPA /WPA2-Personal and Enterprise (IEEE 802.1X/RADIUS, TKIP and AES) Connectors Defined BTB connector is using 2x40 pins header, and Support PCI Express standard. Power requirement 3.3V +/-10% Dimension 60mm x 60mm x 1.2mm Operating -40 to +80 ℃ (installed properly inside the enclosure of the final products) Temperature Storage -40 to +150℃ (installed properly inside the enclosure of the final products) Temperature: Operates in 2.4 US: and 5 GHz 2,400 to 2,483.5 MHz frequency bands. 4,940 to 4,990 MHz (frequency range) 5,725 to 5,850 MHz EU: 2,400 to 2,483.5 MHz 5,725 to 5,875 MHz

2 Chapter 2 Getting Started This chapter covers the module layout, and block diagram, hardware installation of the WAPN008-1. Software installation is covered in the next chapter. The following topics are covered:  Module Layout  Block Diagram  Hardware Installation  Software Installation

WAPN008-1 User’s Manual Getting Started Module Layout Top and Bottom Block Diagram Below is a block diagram of the WAPN008-1.

WAPN008-1 User’s Manual Getting Started Connector Locations

WAPN008-1 User’s Manual Getting Started PCI Bus Connector PIN Assignments Function Connect to Pin Pin Function Connect to 3.3v 3.3v 1 2 GND GND 3.3v 3.3v 3 4 GND GND 3.3v 3.3v 5 6 ERXD3 PHY RGMII 3.3v 3.3v 7 8 ERXD2 PHY RGMII 3.3v 3.3v 9 10 ERXD1 PHY RGMII 3.3v 3.3v 11 12 ERXD0 PHY RGMII 3.3v 3.3v 13 14 GND GND GPIO 16 I2C_SCLK 15 16 GND GND GPIO 17 I2C_DATA 17 18 ETX_CLK ETX_CLK GND GND 19 20 GND GND GPIO 21 POWER 2 21 22 GND GND GPIO 1 JP1 Debug 23 24 ETX_EN ETX_EN GND GND 25 26 GND GND GPIO 4 S17_INT 27 28 GND GND GND GND 29 30 ETXD3 PHY RGMII GPIO 0 I2C_INT0 31 32 ETXD2 PHY RGMII GND GND 33 34 ETXD1 PHY RGMII GPIO 3 UR_DSR 35 36 ETXD0 PHY RGMII GPIO 9 UR_SIN 37 38 GND GND GPIO 10 UR_SOUT 39 40 GND GND GPIO 13 MDC 41 42 ERX_CLK ERX_CLK GPIO 14 MDIO 43 44 GND GND GPIO 20 POWER 1 45 46 GND GND GND GND 47 48 ERX_EN ERX_EN GPIO 22 POWER 3 49 50 GND GND GND GND 51 52 GND GND GPIO 2 UR_DTR 53 54 EMDC GIGA PHY GND GND 55 56 EMDIO GIGA PHY GPIO 11 Reset 57 58 GND GND GND GND 59 60 GND GND GPIO 12 LAN 10/100 61 62 TXP0 10/100 LAN GND GND 63 64 TXN0 10/100 LAN GPIO 15 Reserved 65 66 GND GND GND GND 67 68 RXP0 10/100 LAN SYS_RST_L GIGA PHY Reset 69 70 RXN0 10/100 LAN AVDD18 Fast Ethernet bios 71 72 GND GND AVDD18 Fast Ethernet bios 73 74 GND GND AVDD18 Fast Ethernet bios 75 76 USB_DM USB port GND GND 77 78 USB_DP USB port GND GND 79 80 GND GND

WAPN008-1 User’s Manual Getting Started Hardware Installation The WAPN008-1 can be installed into all Moxa wireless system board series. Step for Installation 1. Install the WAPN008-1 PCI card on the system board. Apply pressure to both bus connectors and gently press the board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the board, as this can lead to bent/broken pins. 2. Screw on the WAPN008-1 PCI card. 3. Screw on the all the necessary chassis. Software Installation After physically installing the WAPN008-1, your operating system must be configured to recognize the new system board. Step for Installation 1. Apply power to the system board. 2. Connect system board and PC with Ethernet cable. 3. Open a browser and type: 192.168.127.253 to open the system login webpage. 4. Login the webpage with default password: root in order to verify that all of the hardware is install properly.

WAPN008-1 User’s Manual Getting Started Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: SLE-WAPN008-1 ”

WAPN008-1 User’s Manual Getting Started Information for the OEMs and Integrators Any party of the installer who likes to use the module of 4.9GHz band shall fulfill licensing requirement (§90.1207). The installation to Aeronautical mobile operations are prohibited (§90.1205). The end product with an embedded WAPN008-1 module may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15. The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCCID: SLE-WAPN008-1 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Maximum Permissible Exposure (MPE): Ensure that at least 50 cm separation distance is maintained between the wireless module and the body of the user, when Panel antennas, ANT-WSB5-PNF-18 or ANT-WDB-PNF-1518, are used. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain 3.8dBi For 2.4 GHz 1 MOXA ANT-WDB-ANM-0306 Dipole 6.3dBi For 4.9 GHz 6.3dBi For 5 GHz 1.8dBi For 2.4GHz 2 MOXA ANT-WDB-ARM-0202 Dipole 1.8dBi For 4.9 GHz 1.8dBi For 5 GHz 2.04dBi For 2.4GHz 3 MOXA ANT-WDB-ARM-02 Dipole 0.81dBi For 4.9 GHz 0.81dBi For 5 GHz 4.62dBi For 2.4GHz 4 MOXA ANT-WDB-ANM-0502 Dipole 2dBi For 4.9 GHz 2dBi For 5GHz 5 MOXA ANT-WSB5-ANF-12 Dipole 12dBi For 5 GHz 6 MOXA ANT-WSB5-PNF-18 Panel 18dBi For 5 GHz 15dBi For 2.4GHz 7 MOXA ANT-WDB-PNF-1518 Panel 18dBi For 5GHz 8 Huber+Suhner 1356.17.0042 Railway 13dBi For 5GHz 9 Huber+Suhner 1356.17.0077 Dipole 14dBi For 5GHz

WAPN008-1 User’s Manual Getting Started


Document Created: 2019-10-30 15:46:34
Document Modified: 2019-10-30 15:46:34
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC