Users Manual

FCC ID: SLE-WAPC002

Users Manual

Download: PDF
FCCID_4055958

Moxa 802.11a/n/ac WAPC002 User’s Manual www.moxa.com First Edition, April 2018 2018 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.

WAPC002 User’s Manual The hardware and software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright 2018 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks MOXA is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time. Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Technical Support Contact Information www.moxa.com/support

Table of Contents Chapter 1 Introduction Overview Specification Chapter 2 Getting Started Module Layout Block Diagram Hardware Installation Software Installation

WAPC002 User’s Manual Introduction 1 Chapter 1 Introduction The following topics are covered in this chapter: Overview Specifications

WAPC002 User’s Manual Introduction Overview WAPC002 PCIe module is designed to provide wireless communication for Moxa industrial wireless products. It communicates via the standard 802.11a/n/ac protocols on standard 5GHz and 5GHz DFS channels. The WAPC002 uses the QCA99X4 SoC Wireless chipset from Qualcomm. Specification Features WAPC002 Chipset Qualcomm QCA99X4 Baseband - DSSS with DBPSK, DQPSK, CCK Processor (BBP) - OFDM with BPSK, QPSK, 16QAM, 64QAM - 802.11a : 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps - 802.11n: 64QAM @ 600 Mbps to BPSK @ 6.5 Mbps - 802.11ac: 256QAM @ 1,733 Mbps to BPSK @ 29.3 Mbps security engine (multiplesupported)supported) - 64-bit and 128-bit WEP encryption, WPA /WPA2-Personal and Enterprise (IEEE supported) 802.1X/RADIUS, TKIP and AES) Connectors PCIE Express Mini Card Power 3.3V +/-10% requirement Dimension 60mm x 60mm x 1.2mm Operating -40 to 50℃ Temperature Storage -40 to 85℃ Temperature: Operates in 5 US: GHz frequency 5.180 to 5.240 (4 channels) bands. 5.260 to 5.320 (4 channels) 5.500 to 5.700 GHz (11 channels) 5.745 to 5.825 GHz (5 channels) EU: 5.180 to 5.240 (4 channels) 5.260 to 5.320 (4 channels) 5.500 to 5.700 GHz (11 channels) JP: 5.180 to 5.240 (4 channels) 5.260 to 5.320 (4 channels) 5.500 to 5.700 GHz (11 channels)

2 Getting Started Chapter 2 This chapter covers the module layout, and block diagram, hardware installation of the WAPC002. Software installation is covered in the next chapter. The following topics are covered: Module Layout Block Diagram Hardware Installation Software Installation

WAPC002 User’s Manual Getting Started mPCIe Bus Connector PIN Assignments Function Connect to Pin Pin Function Connect to WAKE_L WAKE_L 1 2 3.3V DVDD33 RESERVED NC 3 4 GND GND RESERVED NC 5 6 1.5V NC CLKREQ_L NC 7 8 UIM_PWR NC GND GND 9 10 UIM_DATA NC REFCLK- REFCLK- 11 12 UIM_CLK NC REFCLK+ REFCLK+ 13 14 UIM_RESET NC GND GND 15 16 UIM_VPP NC UIM_C8 NC 17 18 GND GND UIM_C9 NC 19 20 W_DISABLE_L GPIO18 GND GND 21 22 RESET_L RESET_L PERn0 PERn0 23 24 3.3VAUX DVDD33 PERp0 PERp0 25 26 GND GND GND GND 27 28 1.5V NC GND GND 29 30 SMB_CLK NC PETn0 PETn0 31 32 SMB_DATA NC PETp0 PETp0 33 34 GND GND GND GND 35 36 USB_D- NC RESERVED NC 37 38 USB_D+ NC RESERVED NC 39 40 GND GND RESERVED NC 41 42 LED_WWAN_L NC RESERVED GND 43 44 LED_WLAN_L GPIO17 RESERVED DVDD33 45 46 LED_WPAN_L NC RESERVED DVDD33 47 48 1.5V NC RESERVED DVDD33 49 50 GND GND RESERVED DVDD33 51 52 3.3V DVDD33

WAPC002 User’s Manual Getting Started Hardware Installation The WAPC002 can be installed into all Moxa wireless system board series. Required Professional Installation Step 1. Install the WAPC002 PCIE card on the system board. Apply pressure to both bus connectors and gently press the board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the board, as this can lead to bent/broken pins. 2. Screw on the WAPC002 PCIE card. 3. Screw on the all the necessary chassis. Software Installation After physically installing the WAPC002, your operating system must be configured to recognize the new system board. Step for Installation 1. Apply power to the system board. 2. Connect system board and PC with Ethernet cable. 3. Open a browser and type: 192.168.127.253 to open the system login webpage. 4. Login the webpage with default password: root in order to verify that all of the hardware is install properly.

WAPC002 User’s Manual Getting Started Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 60 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 60cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: SLE-WAPC002 ”

WAPC002 User’s Manual Getting Started Canada, Industry Canada (IC) Notices This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Devraient également être informés les utilisateurs que les radars à haute puissance sont désignés comme utilisateurs principaux (c.-à-utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient provoquer des interférences et / ou endommager les appareils LE-LAN. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 60cm from a person's body). Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils mobiles (antennes sont supérieures à 60 cm à partir du corps d'une personne). End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 60cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains IC: 9335A-WAPC002 “ Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions.

WAPC002 User’s Manual Getting Started Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCCID: SLE-WAPC002 and IC: 9335A-WAPC002 has been approved by FCC/IC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain 1 MOXA MAT-WDB-PA-NF-2-0708 Panel 8.77dBi for 5.15~5.25GHz 8.77dBi for 5.25~5.35GHz 8.50dBi for 5.47~5.725GHz 8.18dBi for 5.725~5.825GHz 2 MOXA MI05-A1-XX23037-X0 Panel 23dBi for 5GHz 3 MOXA MI05-A1-XX16020-X0 Panel 12dBi for 5GHz 4 MOXA WI25-A1-0810012-RG316 Panel 10.5dBi for 5GHz 5 MOXA ANT-WSB5-PNF-18 Panel 18dBi for 5GHz 6 MOXA ANT-WDB-PNF-1518 Panel 18dBi for 5GHz 7 MOXA ANT-WDB-ARM-02 Dipole 0.81dBi for 5GHz 8 MOXA ANT-WSB-ANF-12 Dipole 12dBi for 5GHz 9 MOXA MAT-WDB-CA-RM-2-0205 Dipole 5.0dBi for 5.15~5.25GHz 5.7dBi for 5.25~5.35GHz 4.9dBi for 5.47~5.725GHz 5.2dBi for 5.725~5.825GHz 10 MOXA MAT-WDB-DA-RM-2-0203-1m Dipole 3.80dBi for 5.15~5.25GHz 2.72dBi for 5.25~5.35GHz 2.26dBi for 5.47~5.725GHz 2.34dBi for 5.725~5.825GHz 11 MOXA ANT-WDB-ANM-0306 Dipole 5.7dBi for 5.15~5.25GHz 5.7dBi for 5.25~5.35GHz 6.3dBi for 5.47~5.725GHz 6.3dBi for 5.725~5.825GHz 12 MOXA ANT-WDB-ARM-0202 Dipole 1.8dBi for 5GHz 13 MOXA ANT-WDB-ANM-0502 Dipole 2.0dBi for 5GHz 14 MOXA ANT-WDB-ANM-0407 Dipole 7.0dBi for 5GHz 15 MOXA ANT-WDB-ANF-0609 Dipole 9.0dBi for 5GHz 16 MOXA ANT-WDB-ANM-0609 Dipole 9.0dBi for 5GHz 17 MOXA MHH-A11-XX110170-X0 Railway 8.0dBi for 5GHz 18 MOXA WI25-A1-1215053-X0 Sector 15dBi for 5GHz 19 MOXA TOP 200 AMR MF-05-4 Patch 8.5dBi for 5GHz

NCC 警語: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或 變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善 至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫 療用電波輻射性電機設備之干擾。 本模組於取得認證後將依規定於模組本體標示審驗合格標籤，並要求最終產品平台廠商(OEM Integrator) 於最終產品平台(End Product)上標示” 本產品內含射頻模組，其 NCC 型式認證號碼為: CCXXxxYYyyyZzW


Document Created: 2018-10-25 11:09:28
Document Modified: 2018-10-25 11:09:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC