TEST REPORT

FCC ID: SK9C3A-1H

Test Report

Download: PDF

FCCID_939344

Table of Contents
1.0 General 3
1.1 Purpose 3
1.2 Product Description 3
1.3 Test Methodology and Considerations 3
2.0 Test Facilities 3
2.1 Location 3
2.2 Laboratory Accreditations/Recognitions/Certifications 3
2.3 Radiated Emissions Test Site Description 4
2.3.1 Semi-Anechoic Chamber Test Site 4
2.3.2 Open Area Tests Site (OATS) 5
2.4 Conducted Emissions Test Site Description 6
3.0 Applicable Standards and References 6
4.0 List of Test Equipment 7
5.0 Support Equipment 8
6.0 EUT Setup Block Diagram 8
7.0 Summary of Tests 9
7.1 Antenna Requirement 9
7.2 Power Line Conducted Emissions 9
7.2.1 Test Methodology 9
7.2.2 Test Results 9
7.3 Radiated Emissions - Unintentional Radiation 11
7.3.1 Test Methodology 11
7.3.2 Test Results 11
7.4 Peak Output Power 12
7.4.1 Test Methodology 12
7.4.2 Test Results 12
7.5 Channel Usage 13
7.5.1 Carrier Frequency Separation 13
7.5.1.1 Test Methodology 13
7.5.1.2 Test Results 13
7.5.2 Number of Hopping Channels 14
7.5.3 Channel Dwell Time 14
7.5.3.1 Test Methodology 14
7.5.3.2 Test Results 14
7.5.4 20dB Bandwidth 15
7.5.4.1 Test Methodology 15
7.5.4.2 Test Results 15
7.6 Band-edge Compliance and Spurious Emissions 17
7.6.1 Band-edge Compliance of RF Conducted Emissions 17
7.6.1.1 Test Methodology 17
7.6.1.2 Test Results 17
7.6.2 RF Conducted Spurious Emissions 18
7.6.2.1 Test Methodology 18
7.6.2.2 Test Results 18
7.6.3 Radiated Spurious Emissions – Intentional Radiation (Restricted Bands) 21
7.6.3.1 Test Methodology 21
7.6.3.2 Duty Cycle Correction 21
7.6.3.3 Test Results 21
7.6.3.4 Sample Calculations 22
8.0 CONCLUSION 22

Additional Exhibits Included In Filing
Test Setup Photographs
BOM (Parts List)
Schematics

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

2.3 Radiated Emissions Test Site Description

2.3.1 Semi-Anechoic Chamber Test Site
The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The
chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid
is 101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on
steel panels and installed directly on the inner walls of the chamber.

The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The
chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is
bound to the ground plane using 3/4" stainless steel braided cable.

The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely
operated from inside the control room located 25’ from the range. The turntable is electrically
bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table.
The steel fingers make constant contact with the ground plane during operation.

Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary.
The pit is equipped with 1 - 4” PVC chases from the turntable to the pit that allow for cabling to
the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can
be supplied to the EUT from the pit.

A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3-1 below:

3 Meters

5 Feet
Diamete
r

20 Feet

30 Feet

Figure 2.3-1: Semi-Anechoic Chamber Test Site

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 4

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

2.3.2 Open Area Tests Site (OATS)
The open area test site consists of a 40’ x 66’ concrete pad covered with a perforated electro-
plated galvanized sheet metal. The perforations in the sheet metal are 1/8” holes that are
staggered every 3/16”. The individual sheets are placed to overlap each other by 1/4” and are
riveted together to provide a continuous seam. Rivets are spaced every 3” in a 3 x 20 meter
perimeter around the antenna mast and EUT area. Rivets in the remaining area are spaced as
necessary to properly secure the ground plane and maintain the electrical continuity.

The entire ground plane extends 12’ beyond the turntable edge and 16’ beyond the antenna mast
when set to a 10 meter measurement distance. The ground plane is grounded via 4 - 8’ copper
ground rods, each installed at a corner of the ground plane and bound to the ground plane using
3/4" stainless steel braided cable.

The turntable is an all aluminum 10’ flush mounted table installed in an all aluminum frame. The
table is remotely operated from inside the control room located 40’ from the range. The turntable
is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of
the turn table. The steel fingers make constant contact with the ground plane during operation.

Adjacent to the turntable is a 7’ x 7’ square and 4’ deep concrete pit used for support equipment if
necessary. The pit is equipped with 5 - 4” PVC chases from the pit to the control room that allow
for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit
so cables can be supplied to the EUT from the pit. The pit is covered with 2 sheets of 1/4"
diamond style re-enforced steel sheets. The sheets are painted to match the perforated steel
ground plane; however the underside edges have been masked off to maintain the electrical
continuity of the ground plane. All reflecting objects are located outside of the ellipse defined in
ANSI C63.4.

A diagram of the Open Area Test Site is shown in Figure 2.3-2 below:

10

3 Meters

40

7x7x4
Pit

66 Feet

Figure 2.3-2: Open Area Test Site

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 5

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

5.0 SUPPORT EQUIPMENT

Table 5-3: Support Equipment
Item Equipment Type Manufacturer Model Number Serial Number FCC ID

The EUT was tested as a stand alone device and no support equipment was utilized.

6.0 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM

Spectrum Analyzer

50 Ohm connection to
Spectrum Analyzer -
Used for conducted
measurements only.

240 VAC Monophase 240 VAC Monophase
120-480 VAC Polyphase 120-480 VAC Polyphase

Configuration 1 Configuration 2

Figure 6-1: EUT Test Setup

*See Test Setup photographs for additional detail.

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 8

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.0 SUMMARY OF TESTS
Along with the tabular data shown below, plots were taken of all signals deemed important enough to
document.

7.1 Antenna Requirement
The C3A1H utilizes an integral antenna which can not be removed.

7.2 Power Line Conducted Emissions

7.2.1 Test Methodology
ANSI C63.4 sections 6 and 7 were the guiding documents for this evaluation. Conducted emissions were
performed from 150kHz to 30MHz with the spectrum analyzer’s resolution bandwidth set to 9kHz and the
video bandwidth set to 30kHz. The calculation for the conducted emissions is as follows:

Corrected Reading = Analyzer Reading + LISN Loss + Cable Loss
Margin = Applicable Limit - Corrected Reading

7.2.2 Test Results
Results of the test are shown below in and Table 7.2-1 to 7.2-4.

Table 7.2-1: Conducted EMI Results – Mono Phase 240 VAC
Total
Uncorrected Reading Limit Margin
Frequency Correction Corrected Level (dBuV)
(dBuV) (dBuV) (dB) Line
(MHz) Factor
(dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
Line 1
0.23 35.5 27.7 9.80 45.30 37.50 62.45 52.45 17.1 14.9 GND
0.3 20.1 11.2 9.80 29.90 21.00 60.24 50.24 30.3 29.2 GND
0.35 34.3 27.4 9.80 44.10 37.20 58.96 48.96 14.9 11.8 GND
0.46 23.7 21.7 9.80 33.50 31.50 56.69 46.69 23.2 15.2 GND
0.6 20.7 19.1 9.80 30.50 28.90 56.00 46.00 25.5 17.1 GND
25.17 24.8 24.3 10.20 35.00 34.50 60.00 50.00 25.0 15.5 GND
Line 2
0.23 35.9 28.1 9.80 45.70 37.90 62.45 52.45 16.7 14.5 GND
0.29 18.4 10.8 9.80 28.20 20.60 60.52 50.52 32.3 29.9 GND
0.35 34.7 27.9 9.80 44.50 37.70 58.96 48.96 14.5 11.3 GND
0.45 23.9 22.1 9.80 33.70 31.90 56.88 46.88 23.2 15.0 GND
0.7 19.9 17.8 9.80 29.70 27.60 56.00 46.00 26.3 18.4 GND
25.17 24.2 23.8 10.20 34.40 34.00 60.00 50.00 25.6 16.0 GND

Table 7.2-2: Conducted EMI Results – Poly Phase 120 VAC
Total
Uncorrected Reading Limit Margin
Frequency Correction Corrected Level (dBuV)
(dBuV) (dBuV) (dB) Line
(MHz) Factor
(dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
Line 1
0.15 33.4 23.5 9.80 43.20 33.30 66.00 56.00 22.8 22.7 GND
0.26 34.4 24.1 9.80 44.20 33.90 61.43 51.43 17.2 17.5 GND
0.39 29.3 19.2 9.80 39.10 29.00 58.06 48.06 19.0 19.1 GND
0.51 13.4 11.2 9.80 23.20 21.00 56.00 46.00 32.8 25.0 GND
0.69 19.2 13.5 9.80 29.00 23.30 56.00 46.00 27.0 22.7 GND
18.89 9.5 4 10.11 19.61 14.11 60.00 50.00 40.4 35.9 GND
Line 2
0.26 38.2 30.1 9.80 48.00 39.90 61.43 51.43 13.4 11.5 GND
0.39 34.6 25.9 9.80 44.40 35.70 58.06 48.06 13.7 12.4 GND
0.68 31.5 26.1 9.80 41.30 35.90 56.00 46.00 14.7 10.1 GND
1.06 28.8 18.2 9.80 38.60 28.00 56.00 46.00 17.4 18.0 GND
1.77 25.8 15.5 9.80 35.60 25.30 56.00 46.00 20.4 20.7 GND
21.89 10 4.5 10.03 20.03 14.53 60.00 50.00 40.0 35.5 GND

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 9

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

Table 7.2-3: Conducted EMI Results – Poly Phase 240 VAC
Total
Uncorrected Reading Limit Margin
Frequency Correction Corrected Level (dBuV)
(dBuV) (dBuV) (dB) Line
(MHz) Factor
(dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
Line 1
0.26 32.4 22.3 9.80 42.20 32.10 61.43 51.43 19.2 19.3 GND
0.39 29 19.3 9.80 38.80 29.10 58.06 48.06 19.3 19.0 GND
0.53 28.5 19.7 9.80 38.30 29.50 56.00 46.00 17.7 16.5 GND
0.67 24.1 16.2 9.80 33.90 26.00 56.00 46.00 22.1 20.0 GND
0.9 20.3 11.5 9.80 30.10 21.30 56.00 46.00 25.9 24.7 GND
2.09 21.7 12.8 9.80 31.50 22.60 56.00 46.00 24.5 23.4 GND
Line 2
0.39 37.7 28.8 9.80 47.50 38.60 58.06 48.06 10.6 9.5 GND
0.52 38.8 30.3 9.80 48.60 40.10 56.00 46.00 7.4 5.9 GND
0.67 37 29.1 9.80 46.80 38.90 56.00 46.00 9.2 7.1 GND
8 33 24 9.90 42.90 33.90 60.00 50.00 17.1 16.1 GND
0.935 32.8 24.1 9.80 42.60 33.90 56.00 46.00 13.4 12.1 GND
2.18 29.5 20 9.80 39.30 29.80 56.00 46.00 16.7 16.2 GND

Table 7.2-4: Conducted EMI Results – Poly Phase 480 VAC
Total
Uncorrected Reading Limit Margin
Frequency Correction Corrected Level (dBuV)
(dBuV) (dBuV) (dB) Line
(MHz) Factor
(dB)
Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average
Line 1
0.39 32 25.3 9.80 41.80 35.10 58.06 48.06 16.3 13.0 GND
0.53 34.9 28.3 9.80 44.70 38.10 56.00 46.00 11.3 7.9 GND
0.66 35.5 28.5 9.80 45.30 38.30 56.00 46.00 10.7 7.7 GND
0.79 33.7 27.3 9.80 43.50 37.10 56.00 46.00 12.5 8.9 GND
0.93 32.9 26.7 9.80 42.70 36.50 56.00 46.00 13.3 9.5 GND
2.83 29.4 22.4 9.80 39.20 32.20 56.00 46.00 16.8 13.8 GND
Line 2
0.27 31.3 20.7 9.80 41.10 30.50 61.12 51.12 20.0 20.6 GND
0.4 28.7 19.4 9.80 38.50 29.20 57.85 47.85 19.4 18.7 GND
0.52 25.4 17.6 9.80 35.20 27.40 56.00 46.00 20.8 18.6 GND
0.89 25.5 17.7 9.80 35.30 27.50 56.00 46.00 20.7 18.5 GND
1.06 24.1 17 9.80 33.90 26.80 56.00 46.00 22.1 19.2 GND
2.78 21 14.5 9.80 30.80 24.30 56.00 46.00 25.2 21.7 GND

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 10

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.3 Radiated Emissions - Unintentional Radiation

7.3.1 Test Methodology
Radiated emissions tests were performed over the frequency range of 30MHz to 5GHz. Measurements
of the radiated field strength were made at a distance of 3m from the boundary of the equipment under
test (EUT) and the receiving antenna. The antenna height was varied from 1m to 4m so that the
maximum radiated emissions level would be detected. Radiated measurements were made with the
Spectrum Analyzer’s resolution bandwidth set to 120 KHz for measurements above 30MHz. Average
measurements are taken with the RBW and VBW were set to 1MHz and 10 Hz respectively for
measurements above 1000MHz.

Measurements were performed for all configurations and voltages. Worst case data for each
configuration is presented below.

7.3.2 Test Results
Results of the test are given in Table 7.3-1 and 7.3-2 below:

Table 7.3-1: Radiated Emissions Tabulated Data – Mono Phase 240 VAC
Level Antenna Correction Corrected Level Limit Margin
Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB)
(MHz)
pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg
30 --------- 17.83 H -7.50 --------- 10.33 -------- 40.0 --------- 29.67
70.95 --------- 18.37 H -20.55 --------- -2.18 -------- 40.0 --------- 42.18
75.491 --------- 37.72 V -19.91 --------- 17.81 -------- 40.0 --------- 22.19
79.56 --------- 53.59 V -19.18 --------- 34.41 -------- 40.0 --------- 5.59
83.89 --------- 36.45 V -18.09 --------- 18.36 -------- 40.0 --------- 21.64
88.2 --------- 42.82 V -17.29 --------- 25.53 -------- 43.5 --------- 17.97
96.45 --------- 41.60 V -15.71 --------- 25.89 -------- 43.5 --------- 17.61
104.85 --------- 33.50 H -15.32 --------- 18.18 -------- 43.5 --------- 25.32
591.52 --------- 19.61 H -4.78 --------- 14.83 -------- 46.0 --------- 31.17
956.89 --------- 19.92 H 1.84 --------- 21.76 -------- 46.0 --------- 24.24
* Note: All emissions above 956.89 MHz were attenuated below the permissible limit.

Table 7.3-2: Radiated Emissions Tabulated Data – Poly Phase 120 VAC
Level Antenna Correction Corrected Level Limit Margin
Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB)
(MHz)
pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg
40.77 --------- 51.89 V -14.37 --------- 37.52 -------- 40.0 --------- 2.48
42.93 --------- 54.35 V -15.41 --------- 38.94 -------- 40.0 --------- 1.06
72 --------- 47.00 V -20.42 --------- 26.58 -------- 40.0 --------- 13.42
83.67 --------- 51.69 V -18.15 --------- 33.54 -------- 40.0 --------- 6.46
107.6 --------- 51.60 V -14.40 --------- 37.20 -------- 43.5 --------- 6.30
136.7 --------- 21.82 H -14.43 --------- 7.39 -------- 43.5 --------- 36.11
151.79 --------- 21.59 H -15.07 --------- 6.52 -------- 43.5 --------- 36.98
164.72 --------- 18.72 H -15.68 --------- 3.04 -------- 43.5 --------- 40.46
209.99 --------- 29.98 V -15.30 --------- 14.68 -------- 43.5 --------- 28.82
840.49 --------- 26.86 H 0.08 --------- 26.94 -------- 46.0 --------- 19.06
* Note: All emissions above 840.49 MHz were attenuated below the permissible limit.

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 11

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.4 Peak Output Power

7.4.1 Test Methodology (Conducted Method)
The 20dB bandwidth of the EUT was within the resolution bandwidth of spectrum analyzer, therefore the
power measurement was made using the spectrum analyzer method. The RF output port of the EUT was
directly connected to the input of the spectrum analyzer. The resolution and video bandwidth were set to
> 20 dB bandwidth of the emission measured. The device employs ≥ 50 channels therefore the power is
limited to 1 Watt.

7.4.2 Test Results
Results are shown in table 7.4-1 and figures 7.4-1 to 7.4-3 below:

Table 7.4-1: RF Output Power
Frequency Level
[MHz] [dBm]
909.564 21.58
916.176 21.27
921.700 21.12

* RBW 3 MHz Marker 1 [T1 ]
VBW 10 MHz 21.58 dBm
Ref 30 dBm Att 50 dB SWT 2.5 ms 909.450000000 MHz
30 Offset 10 dB
1
A
20

1 PK
MAXH
10
LVL

0

-10

-20

-30

-40

-50

-60

-70

Center 909.57 MHz 500 kHz/ Span 5 MHz

Date: 11.APR.2008 09:48:47

Figure 7.4-1: Output power – Low Channel
* RBW 3 MHz Marker 1 [T1 ]
VBW 10 MHz 21.27 dBm
Ref 30 dBm Att 50 dB SWT 2.5 ms 915.830000000 MHz
30 Offset 10 dB
1
A
20

1 PK
MAXH
10
LVL

0

-10

-20

-30

-40

-50

-60

-70

Center 916.01 MHz 500 kHz/ Span 5 MHz

Date: 11.APR.2008 10:05:32

Figure 7.4-2: Output power – Mid Channel
ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 12

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

* RBW 3 MHz Marker 1 [T1 ]
VBW 10 MHz 21.12 dBm
Ref 30 dBm Att 50 dB SWT 2.5 ms 921.600000000 MHz
30 Offset 10 dB
1
A
20

1 PK
MAXH
10
LVL

0

-10

-20

-30

-40

-50

-60

-70

Center 921.7 MHz 500 kHz/ Span 5 MHz

Date: 11.APR.2008 10:10:35

Figure 7.4-3: Output power – High Channel

7.5 Channel Usage Requirements

7.5.1 Carrier Frequency Separation

7.5.1.1 Test Methodology
The RF output port of the EUT was directly connected to the input of the spectrum analyzer. The span of
the spectrum analyzer was set wide enough to capture two adjacent peaks and the RBW and VBW were
set to ≥ 1% of the span.

7.5.1.2 Test Results
The maximum 20dB bandwidth of the hopping channel was measured to be 188.00kHz (See figures
7.5.4-1 to 7.5.4-3 below). The adjacent channel separation was measured to be 194.00kHz. Results are
shown in figure 7.5.1-1 below:

* RBW 100 kHz Delta 1 [T1 ]
VBW 300 kHz -0.22 dB
Ref 30 dBm Att 50 dB SWT 2.5 ms 194.000000000 kHz

30 Offset 10 dB Marker 1 [T1 ]
1 1 21.36 dBm
915.999000000 MHz A
20

1 PK
MAXH
10
LVL

0

-10

-20

-30

-40

-50

-60

-70

Center 916.086 MHz 50 kHz/ Span 500 kHz

Date: 15.APR.200 8 09:38:12

Figure 7.5.1-1: Carrier Frequency Separation

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 13

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.5.2 Number of Hopping Channels
The 20dB bandwidth of the device is less than 250 kHz. The device employs 50 hopping channels as
required. Results are shown in Figure 7.5.2-1 below:
* RBW 100 kHz Marker 1 [T1 ]
VBW 300 kHz 21.14 dBm
Ref 30 dBm Att 50 dB SWT 2.5 ms 909.560000000 MHz
30 Offset 10 dB Marker 2 [T1 ]
1 2 dBm
21.04
921.752000000 MHz B
20

1 PK
VIEW
10
LVL

0

-10

-20

-30

-40

-50

-60

-70

Start 907 MHz 1.6 MHz/ Stop 923 MHz

Date: 11.APR.2008 11:25:37

Figure 7.5.2-1: Number of Hopping Channels

7.5.3 Channel Dwell Time

7.5.3.1 Test Methodology
The RF output port of the EUT was directly connected to the input of the spectrum analyzer. The hopping
channel is centered on the analyzer and the span set to 0 Hz. The RBW was set to 1 MHz and the VBW
to 3 MHz. Sweep time was set to 60 ms to capture the burst duration of the emission. The marker –delta
function of the analyzer was employed to measure the burst duration.

7.5.3.2 Test Results
The duration of the RF transmission is 45 ms. There is a minimum 2 second rest period in which the
device hops to another channel according to the pseudorandom frequency table before transmitting
another 45ms burst. Therefore the average time of occupancy on any channel in a 20 second period is
45ms. A single transmission is shown in figure 7.5.3-1 below:

RBW 1 MHz Delta 2 [T1 ]
VBW 3 MHz -21.91 dB
Ref 30 dBm Att 50 dB SWT 60 ms 45.000000 ms
30 Offset 10 dB Marker 1 [T1 ]
19.20 dBm
1 A
20 -80.000000 µs

1 PK
MAXH TRG
10
LVL

0 2

TRG -6.2 dBm
-10

-20

-30

-40

-50

-60

-70

Center 909.564 MHz 6 ms/

Date: 15.APR.2008 10:18:37

Figure 7.5.3-1: Channel Dwell Time

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 14

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.5.4 20dB Bandwidth

7.5.4.1 Test Methodology
The RF output port of the EUT was directly connected to the input of the spectrum analyzer. The
spectrum analyzer span was set to 2 to 3 times the estimated 20 dB bandwidth of the emission. The
RBW was to ≥ 1% of the estimated 20 dB bandwidth. The trace was set to max hold with a peak detector
active. The Delta function of the analyzer was utilized to determine the 20 dB bandwidth of the emission.
The span and RBW were examined and re-adjusted if necessary to meet the requirements of 2 to 3 times
the 20 bandwidth for the span and ≥ 1% of the 20 dB bandwidth for the RBW.

7.5.4.2 Test Results
The maximum 20dB bandwidth was found to be approximately 188.00kHz. Results are shown below in
Table 7.5.4-1 and Figures 7.5.4-1 through 7.5.4-3.

Table 7.5.4-1
Frequency 20dB Bandwidth
(MHz) (kHz)
909.564 160
916.176 171
921.700 188

* RBW 30 kHz Marker 1 [T1 ]
VBW 100 kHz 21.24 dBm
Ref 30 dBm Att 50 dB SWT 2.5 ms 909.569000000 MHz

30 Offset 10 dB ndB [T1] 20.00 dB
1 BW 160.000000000 kHz
Temp 1 [T1 ndB] A
20
1.26 dBm
1 PK
909.492000000 MHz
MAXH
10 Temp 2 [T1 ndB]
1.18 dBm LVL
T1 T2
909.652000000 MHz
0

-10

-20

-30

-40

-50

-60

-70

Center 909.57 MHz 50 kHz/ Span 500 kHz

Date: 11.APR.200 8 09:55:48

Figure 7.5.4-1: 20dB Bandwidth Low Channel

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 15

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

* RBW 30 kHz Marker 1 [T1 ]
VBW 100 kHz 21.11 dBm
Ref 30 dBm Att 50 dB SWT 2.5 ms 915.989000000 MHz

30 Offset 10 dB ndB [T1] 20.00 dB
1 BW 171.000000000 kHz
Temp 1 [T1 ndB] A
20
1.37 dBm
1 PK
915.905000000 MHz
MAXH
10 Temp 2 [T1 ndB]
T2 1.39 dBm LVL
T1
916.076000000 MHz
0

-10

-20

-30

-40

-50

-60

-70

Center 915.989 MHz 50 kHz/ Span 500 kHz

Date: 11.APR.200 8 10:07:05

Figure 7.5.4-2: 20dB Bandwidth Mid Channel

* RBW 30 kHz Marker 1 [T1 ]
VBW 100 kHz 21.00 dBm
Ref 30 dBm Att 50 dB SWT 2.5 ms 921.753000000 MHz

30 Offset 10 dB ndB [T1] 20.00 dB
1 BW 188.000000000 kHz
Temp 1 [T1 ndB] A
20
0.84 dBm
1 PK
921.661000000 MHz
MAXH
10 Temp 2 [T1 ndB]
0.71 dBm LVL
T1 T2
921.849000000 MHz
0

-10

-20

-30

-40

-50

-60

-70

Center 921.75 MHz 50 kHz/ Span 500 kHz

Date: 11.APR.200 8 10:11:51

Figure 7.5.4-3: 20dB Bandwidth High Channel

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 16

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.6 Band-Edge Compliance and Spurious Emissions

7.6.1 Band-Edge Compliance of RF Conducted Emissions

7.6.1.1 Test Methodology
The RF output port of the EUT was directly connected to the input of the spectrum analyzer. The EUT
was investigated at the lowest and highest channel available to determine band-edge compliance. For
each measurement the spectrum analyzer’s RBW was set to 100 kHz, which is ≥ 1% of the span, and the
VBW was set to 300kHz.

7.6.1.2 Test Results
In a 100 kHz bandwidth at the lower and upper band-edge, the radio frequency power that was produced
by the EUT is at least 20 dB below that in the 100 kHz bandwidth within the band that contains the
highest level of desired power. Band-edge compliance is displayed in Figures 7.6.1-1 and 7.6.1-4
* RBW 100 kHz Delta 1 [T1 ] * RBW 100 kHz Delta 1 [T1 ]
VBW 300 kHz 53.99 dB VBW 300 kHz 53.35 dB
Ref 30 dBm Att 50 dB SWT 2.5 ms 9.184500000 MHz Ref 30 dBm Att 50 dB SWT 2.5 ms -6.245000000 MHz

30 Offset 10 dB Marker 1 [T1 ] 30 Offset 10 dB Marker 1 [T1 ]
1
-32.78 dBm 1 -32.28 dBm
900.409500000 MHz A 928.000000000 MHz A
20 20

1 PK 1 PK
MAXH MAXH
10 10
LVL LVL

0 0

-10 -10

-20 -20

1
-30 -30 1

-40 -40

-50 -50

-60 -60

-70 -70

Start 900 MHz 975 kHz/ Stop 909.75 MHz Start 921.5 MHz 850 kHz/ Stop 930 MHz

Date : 11.A PR.200 8 09:5 8:54 Date : 11.A PR.200 8 10:1 4:00

Figure 7.6.1-1: Lower Band-edge Figure 7.6.1-2: Upper Band-edge
* RBW 100 kHz Delta 1 [T1 ] * RBW 100 kHz Delta 1 [T1 ]
VBW 300 kHz 52.89 dB VBW 300 kHz 51.82 dB
Ref 30 dBm Att 50 dB SWT 2.5 ms 8.465600000 MHz Ref 30 dBm Att 50 dB SWT 2.5 ms -7.628272000 MHz

30 Offset 10 dB Marker 1 [T1 ] 30 Offset 10 dB Marker 1 [T1 ]
1 dBm
-31.32 1 -30.74 dBm
901.123200000 MHz A 929.389040000 MHz A
20 20

1 PK 1 PK
MAXH MAXH
10 10
LVL LVL

0 0

-10 -10

-20 -20

1 1
-30 -30

-40 -40

-50 -50

-60 -60

-70 -70

Center 905.2 MHz 1.04 MHz/ Span 10.4 MHz Start 921.272 MHz 872.8 kHz/ Stop 930 MHz

Date : 14.A PR.200 8 09:0 9:55 Date : 14.A PR.200 8 09:5 1:19

Figure 7.6.1-3: Lower Band-edge – Hopping Figure 7.6.1-4: Upper Band-edge - Hopping

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 17

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.6.2 RF Conducted Spurious Emissions

7.6.2.1 Test Methodology
The RF output port of the EUT was directly connected to the input of the spectrum analyzer. The EUT
was investigated for conducted spurious emissions from 30MHz to 10GHz, 10 times the highest
fundamental frequency. Measurements were made at the low, center and high channels of the EUT. For
each measurement, the spectrum analyzer’s RBW was set to 100kHz. A peak detector function was
used with the trace set to max hold.

7.6.2.1 Test Results
All emissions found were greater than 20dB down from the fundamental carrier. The RF conducted
spurious emissions were measured in the band of 30MHz to 10GHz. Results are shown below in Figure
7.6.2-1 through 7.6.2-6.

* RBW 100 kHz Marker 1 [T1 ]
VBW 300 kHz 21.13 dBm
Ref 30 dBm * Att 30 dB SWT 100 ms 910.760000000 MHz

30 Offset 10 dB
1
B
20

1 PK
MAXH
10
LVL

D1 1.13 dBm
0

-10

-20

-30

-40

-50

-60

-70

Start 30 MHz 97 MHz/ Stop 1 GHz

Date: 11.APR.200 8 10:01:43

Figure 7.6.2-1 RF Conducted Spurious Emissions – Low Channel

* RBW 100 kHz Marker 1 [T1 ]
VBW 300 kHz -36.80 dBm
Ref 30 dBm * Att 30 dB SWT 900 ms 4.960000000 GHz

30 Offset 10 dB

B
20

1 PK
MAXH
10
LVL

D1 1.13 dBm
0

-10

-20

-30
1

-40

-50

-60

-70

Start 1 GHz 900 MHz/ Stop 10 GHz

Date: 11.APR.200 8 10:03:02

Figure 7.6.2-2 RF Conducted Spurious Emissions – Low Channel

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 18

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

* RBW 100 kHz Marker 1 [T1 ]
VBW 300 kHz 21.05 dBm
Ref 30 dBm * Att 30 dB SWT 100 ms 916.580000000 MHz

30 Offset 10 dB
1
B
20

1 PK
MAXH
10
LVL

0 D1 1.05 dBm

-10

-20

-30

-40

-50

-60

-70

Center 515 MHz 97 MHz/ Span 970 MHz

Date: 11.APR.200 8 10:07:48

Figure 7.6.2-3 RF Conducted Spurious Emissions – Mid Channel

* RBW 100 kHz Marker 1 [T1 ]
VBW 300 kHz -33.83 dBm
Ref 30 dBm * Att 30 dB SWT 900 ms 1.828000000 GHz

30 Offset 10 dB

B
20

1 PK
MAXH
10
LVL

0 D1 1.05 dBm

-10

-20

-30 1

-40

-50

-60

-70

Start 1 GHz 900 MHz/ Stop 10 GHz

Date: 11.APR.200 8 10:08:48

Figure 7.6.2-4 RF Conducted Spurious Emissions – Mid Channel

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 19

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

* RBW 100 kHz Marker 1 [T1 ]
VBW 300 kHz 20.93 dBm
Ref 30 dBm * Att 30 dB SWT 100 ms 922.400000000 MHz

30 Offset 10 dB Marker 2 [T1 ]
-35.75
1 dBm
460.680000000 MHz B
20

1 PK
MAXH
10
LVL

0 D1 0.93 dBm

-10

-20

-30
2

-40

-50

-60

-70

Center 515 MHz 97 MHz/ Span 970 MHz

Date: 11.APR.200 8 10:15:34

Figure 7.6.2-5 RF Conducted Spurious Emissions – High Channel

* RBW 100 kHz Marker 1 [T1 ]
VBW 300 kHz -33.71 dBm
Ref 30 dBm * Att 30 dB SWT 900 ms 1.828000000 GHz

30 Offset 10 dB

B
20

1 PK
MAXH
10
LVL

0 D1 0.93 dBm

-10

-20

-30 1

-40

-50

-60

-70

Start 1 GHz 900 MHz/ Stop 10 GHz

Date: 11.APR.200 8 10:17:11

Figure 7.6.2-6 RF Conducted Spurious Emissions – High Channel

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 20

Model: C3A1H FCC ID: SK9C3A-1H IC: 864G-C3A1H

7.6.3 Radiated Spurious Emissions – Intentional Radiation (Restricted Bands)

7.6.3.1 Test Methodology
Radiated emissions tests were made over the frequency range of 30MHz to 10GHz, 10 times the highest
fundamental frequency.

The EUT was rotated through 360° and the receive antenna height was varied from 1m to 4m so that the
maximum radiated emissions level would be detected. For frequencies below 1000MHz, quasi-peak
measurements were made using a resolution bandwidth (RBW) of 120 kHz and a video bandwidth (VBW)
of 300 kHz. For frequencies above 1000MHz, average measurements were made using an RBW of 1
MHz and a VBW of 10 Hz and peak measurements were made with RBW of 1 MHz and a VBW of 1
MHz.

The EUT was caused to generate a continuous carrier signal on the hopping channel.

Measurements were performed for all configurations and voltages. Worst case data for each
configuration is presented below.

7.6.3.2 Duty Cycle Correction
For average radiated measurements, the measured level was reduced by a factor 6.94dB to account for
the duty cycle of the EUT. Referencing the dwell time justification in section 7.5.3 above the worst case
duty cycle within 100ms is 45% or 45ms. The duty cycle correction factor is determined using the
formula: 20log (0.45)=6.94dB.

7.6.3.3 Test Results
Radiated spurious emissions found in the band of 30MHz to 10GHz are reported in Tables 7.6.3-1 and
7.6.3-2.

Table 7.6.3-1: Radiated Spurious Emissions – Monophase 240VAC
Level Antenna Correction Corrected Level Limit Margin
Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB)
(MHz)
pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg
Low Channel
2728.74 53.50 53.50 H 0.28 53.78 46.85 74.0 54.0 20.22 7.15
2728.74 58.00 58.00 V 0.03 58.03 51.09 74.0 54.0 15.97 2.91
3638.32 52.97 52.97 H 3.38 56.35 49.42 74.0 54.0 17.65 4.58
3638.32 52.36 52.36 V 3.41 55.77 48.83 74.0 54.0 18.23 5.17
4547.9 52.42 52.42 H 5.48 57.90 50.96 74.0 54.0 16.10 3.04
4547.9 50.30 50.30 V 5.40 55.70 48.76 74.0 54.0 18.30 5.24
5457.48 45.86 45.86 H 8.10 53.96 47.02 74.0 54.0 20.04 6.98
5457.48 45.72 45.72 V 8.29 54.01 47.08 74.0 54.0 19.99 6.92
Mid Channel
2748.03 47.40 47.40 H 0.34 47.74 40.81 74.0 54.0 26.26 13.19
2748.03 46.25 46.25 V 0.09 46.34 39.41 74.0 54.0 27.66 14.59
3664.04 51.97 51.97 H 3.49 55.46 48.53 74.0 54.0 18.54 5.47
3664.04 52.78 52.78 V 3.53 56.31 49.37 74.0 54.0 17.69 4.63
4580.05 49.80 49.80 H 5.57 55.37 48.43 74.0 54.0 18.63 5.57
4580.05 50.67 50.67 V 5.50 56.17 49.24 74.0 54.0 17.83 4.76
High Channel
2765.1 53.02 53.02 H 0.40 53.42 46.48 74.0 54.0 20.58 7.52
2765.1 51.53 51.53 V 0.15 51.68 44.74 74.0 54.0 22.32 9.26
3686.8 52.24 52.24 H 3.59 55.83 48.90 74.0 54.0 18.17 5.10
3686.8 52.02 52.02 V 3.63 55.65 48.71 74.0 54.0 18.35 5.29
4608.5 50.69 50.69 H 5.65 56.34 49.40 74.0 54.0 17.66 4.60
4608.5 52.21 52.21 V 5.59 57.80 50.87 74.0 54.0 16.20 3.13
* The magnitude of all emissions not reported were below the noise floor of the measurement system.

ACS Report: 08-0089 – 15C Advanced Compliance Solutions Page 21

Document Created: 2008-05-08 11:35:05
Document Modified: 2008-05-08 11:35:05

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC