Test Report

FCC ID: SJV-2879316

Test Report

Download: PDF
FCCID_1931932

ISO/IEC17025 Accredited Lab. Report No: FCC 1303001 File reference No: 2013-03-25 Applicant: Polaris Industries Inc. Product: wireless remote Model No: 2879316 Trademark: Polaris Test Standards: FCC Part 15 Subpart C, Paragraph 15.231 It is herewith confirmed and found to comply with the Test result: requirements set up by ANSI C63.4&FCC Part 15 Subpart C, Paragraph 15.231 regulations for the evaluation of electromagnetic compatibility Approved By Jack Chung Manager Dated: March 25, 2013 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO LTD 5/F,Block 4, Anhua Industrial Zone.,No.8 TaiRan Rd.CheGongMiao,FuTian District, Shenzhen,CHINA. Tel (755) 83448688 Fax (755) 83442996

Report No: 1303001 Page 2 of 32 Date: 2013-03-25 Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:1999 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 899988 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.:899988. IC- Registration No.: IC5205A-02 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration IC No.: 5205A-02. VCCI- Registration No.: R-3015 and C-3332 The EMC Laboratory has been registered and fully described in a report filed with the (VCCI) Voluntary Control Council for Interference. The acceptance letter from the VCCI is maintained in our files. Registration IC No.: R-3015 and C-3332 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 3 of 32 Date: 2013-03-25 Test Report Conclusion Content 1.0 General Details ……………………..…………………………..……………………………..… 4 1.1 Test Lab Details…………………………………………………………..………………….…… 4 1.2 Applicant Details………………………………………………………….……………….…….. 4 1.3 Description of EUT ……………………………………………………………..………….…… 4 1.4 Submitted Sample………………………..……………………………………..……………….. 4 1.5 Test Duration…………………………………….…………………………………..…….……... 5 1.6 Test Uncertainty……………………………………….……………………………...…………... 5 1.7 Test By……………………………………………………………………………………………. 5 2.0 List of Measurement Equipment…………………………………………………………….… 5 3.0 Technical Details………………………………………………………………………………… 6 3.1 Summary of Test Results…………………………………………………………………………. 6 3.2 Test Standards…………………………………………………………………………………….. 6 4.0 EUT Modification………………………………………………………………………………... 6 5.0 Power Line Conducted Emission Test……………………………………………………………. 7 5.1 Schematics of the Test……………………………………………………………………………. 7 5.2 Test Method and Test Procedure…………………………………………………………………. 7 5.3 Configuration of the EUT………………………………………………………………………… 7 5.4 EUT Operating Condition………………………………………………………………………… 8 5.5 Conducted Emission Limit……………………………………………………………………….. 8 5.6 Test Result………………………………………………………………………………………... 8 6.0 Radiated Emission test………………………………………………………………………….. 9 6.1 Test Method and Test Procedure…………………………………………………………………. 9 6.2 Configuration of the EUT………………………………………………………………………… 9 6.3 EUT Operation Condition………………………………………………………………………… 9 6.4 Radiated Emission Limit…………………………………………………………………………. 10 6.5 Test Result………………………………………………………………………………………... 11 7.0 20dB Bandwidth Test…………………………………………………………………………….. 15 8.0 Deactivate Test …………………………………………………………………………………… 17 9.0 Duty Cycle………………………………………………………………………………………... 19 10.0 Antenna Requirement…………………………………………………………………………….. 25 11.0 FCC ID Label…………………………………………………………………………………….. 26 12.0 Photo of Testing………………………….…………………………….………………………… 27 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 4 of 32 Date: 2013-03-25 1.0 General Details 1.1 Test Lab Details Name : SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO LTD Address: 5/F,Block 4, Anhua Industrial Zone.,No.8 TaiRan Rd.CheGongMiao,FuTian District, Shenzhen,CHINA. Telephone: (755) 83448688 Fax: (755) 83442996 Site on File with the Federal Communications Commission – United Sates Registration Number: 899988 For 3m & 10 m OATS Site Listed with Industry Canada of Ottawa, Canada Registration Number: IC: 5205 For 3m & 10 m OATS 1.2 Applicant Details Applicant: Polaris Industries Inc. Address: No. 1000 Lujiazui Ring Road HangSeng Bank Tower, 15/F Shanghai, 200120, China Telephone: -- Fax: -- 1.3 Description of EUT Product: wireless remote Brand Name: Polaris Model Number: 2879316 Additional Model Name N/A Additional Trade Name N/A Rating: Input: 12V, 20mA, 0.24W Operation Frequency 315MHz Antenna Designation PCB Printed antenna 1.4 Submitted Sample 1 Sample The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 5 of 32 Date: 2013-03-25 1.5 Test Duration 2013-03-01 to 2013-03-25 1.6 Test Uncertainty Conducted Emissions Uncertainty =3.6dB Radiated Emissions Uncertainty =4.7dB 1.7 Test Engineer The sample tested by Print Name: Terry Tang 2.0 Test Equipments Instrument Type Manufacturer Model Serial No. Date of Cal. Due Date ESPI Test Receiver ROHDE&SCHWARZ ESPI 3 100379 2012-04-21 2013-04-20 2013-04-20 ROHDE&SCHWARZ ESDV 100008 2012-04-21 ESDV Test Receiver Loop Antenna EMCO 6502 00042960 2012-04-21 2013-04-20 ESPI Test Receiver ROHDE&SCHWARZ ESI26 838786/013 2012-04-21 2013-04-20 3m OATS -- -- N/A 2012-04-21 2013-04-20 Horn Antenna SCHWARZBECK BBHA 9170 BBHA9170265 2012-04-21 2013-04-20 Horn Antenna SCHWARZBECK BBHA 9120D 9120D-631 2012-04-21 2013-04-20 Bilog Antenna Schwarebeck VULB9163 9163/340 2012-04-21 2013-04-20 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 6 of 32 Date: 2013-03-25 3.0 Technical Details 3.1 Summary of test results The EUT has been tested according to the following specifications: Standard Test Type Result Notes FCC Part 15, Paragraph 15.203 Antenna PASS Compliant requirements FCC Part 15, Paragraph 15.207 Conducted N/A N/A Emission Test General FCC Part 15, Paragraph 15.209 PASS Compliant Requirement Radiated FCC Part 15, Paragraph 15.231 (b) PASS Compliant Emission Test FCC Part 15, Paragraph 15.231 (c) 20dB PASS Compliant Bandwidth Testing FCC Part 15, Paragraph 15.231 (a) (1) Deactivate PASS Compliant Testing 3.2 Test Standards FCC Part 15 Subpart C, Paragraph 15.231 4.0 EUT Modification No modification by Shenzhen Timeway Technology Consulting Co., Ltd The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 7 of 32 Date: 2013-03-25 5. Power Line Conducted Emission Test 5.1 Schematics of the test Test Receiver AC Mains L.I.S.N EUT Load EUT: Equipment Under Test 5.2 Test Method and test Procedure The EUT was tested according to ANSI C63.4-2003.The Frequency spectrum From 0.15MHz to 30MHz was investigated. The LISN used was 50ohm/50uH as specified by section 5.1 of ANSI C63.4 –2003. Block diagram of Test setup EUT Cable Receiver 800mm L.S.I.N AC 5.3 Configuration of The EUT The EUT was configured according to ANSI C63.4-2003. All interface ports were connected to the appropriate peripherals. All peripherals and cables are listed below. A. EUT Device Manufacturer Model FCC ID wireless remote Ningbo Lianda Winch Co, Ltd 2879316 SJV-2879316 B. Internal Device Device Manufacturer Model FCC ID/DOC N/A C. Peripherals Device Manufacturer Model FCC ID/DOC Cable N/A The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 8 of 32 Date: 2013-03-25 5.4 EUT Operating Condition Operating condition is according to ANSI C63.4 -2003. A Setup the EUT and simulators as shown on follow B Enable AF signal and confirm EUT active to normal condition 5.5 Power line conducted Emission Limit according to Paragraph 15.207 Frequency Class A Limits (dBμV) Class B Limits (dBμV) (MHz) Quasi-peak Level Average Level Quasi-peak Level Average Level 0.15 ～ 0.50 79.0 66.0 66.0～56.0* 56.0～46.0* 0.50 ～ 5.00 73.0 60.0 56.0 46.0 5.00 ～ 30.00 73.0 60.0 60.0 50.0 Notes: 1. *Decreasing linearly with logarithm of frequency. 2. The tighter limit shall apply at the transition frequencies 5.6 Test Results The frequency spectrum from 0.15MHz to 30MHz was investigated. All reading are quasi-peak values with a resolution bandwidth of 9kHz. Note: Owing to DC operation of EUT, this test item is not performed The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 9 of 32 Date: 2013-03-25 6 Radiated Emission Test 6.1 Test Method and test Procedure: (1) The EUT was tested according to ANSI C63.4 –2003. The radiated test was performed at Timeway Laboratory. This site is on file with the FCC laboratory division, Registration No.899988 (2) The EUT, peripherals were put on the turntable which table size is 1m x 1.5 m, table high 0.8 m. All set up is according to ANSI C63.4-2003. (3) The frequency spectrum from 30 MHz to 1 GHz was investigated. All readings from 30 MHz to 1 GHz are quasi-peak values with a resolution bandwidth of 120 kHz. All readings are above 1 GHz, peak values with a resolution bandwidth of 1 MHz . Measurements were made at 3 meters. (4) The antenna high is varied from 1 m to 4 m high to find the maximum emission for each frequency. (5) Maximizing procedure was performed on the six (6) highest emissions to ensure EUT compliance is with all installation combinations. All data was recorded in the peak detection mode. Quasi-peak readings was performed only when an emission was found to be marginal (within -4 dB of specification limit), and are distinguished with a "QP" in the data table. (6) The antenna polarization : Vertical polarization and Horizontal polarization. Block diagram of Test setup Distance = 3m Computer Pre -Amplifier EUT Turn-table Receiver Ground Plane 6.2 Configuration of The EUT Same as section 5.3 of this report 6.3 EUT Operating Condition Same as section 5.4 of this report. The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 10 of 32 Date: 2013-03-25 6.4 Radiated Emission Limit All emission from a digital device, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strength specified below: A FCC Part 15 Subpart C Paragraph 15.231 Limit Fundamental Frequency (MHz) Field Strength of Field Strength of Spurious Fundamental Emission uV/m dBuV/m uV/m dBuV/m 40.66-40.70 2250 67.04 225 47.04 70-130 1250 61.94 125 41.94 130-174 1250-3370 61.94-70.55 125-375 41.94-51.48 174-260 3750 71.48 375 51.48 260-470 3750-12500 71.48-81.94 375-1250 51.48-61.94 Above 470 12500 81.94 1250 61.94 Note: 1. RF Field Strength (dBuV) = 20 log RF Voltage (uV) 2.Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. 3. The emission limit in this paragraph is based on measurement instrumentation employing an average detector. 4.Linear interpolations for frequency ranges 130-174MHz and 260-470MHz 5.the above field strength limits are specified at a distance of 3-meters and the tighter limits apply at the band edges B. Frequencies in restricted band are complied to limit on Paragraph 15.209. Frequency Range (MHz) Distance (m) Field strength (dBμV/m) 30-88 3 40.0 88-216 3 43.5 216-960 3 46.0 Above 960 3 54.0 Note: 1. RF Voltage (dBuV) = 20 log RF Voltage (uV) 2. In the Above Table, the tighter limit applies at the band edges. 3. Distance refers to the distance in meters between the measuring instrument antenna and the EUT 4. This is a handhold device. The radiated emissions should be tested under 3-axes position (Lying, Side, and Stand), After pre-test. It was found that the worse radiated emission was get at the lying position. 5. All scanning using PK detector. And the final emission level was get using QP detector for frequency range from 30-1000MHz.As to 1G-6G, the final emission level got using PK detector. And Average Value = peak(dBuV/m)+duty cycle factor(dB) 6. New batteries were installed in the equipment under test for radiated emission testing. The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 11 of 32 Date: 2013-03-25 6.5 Test result A Fundamental Radiated Emission Data Product: wireless remote Test Mode: Keeping Tx transmitting Test Item: Fundamental Radiated Emission Temperature: 25℃ and Spurious Emission Data Test Voltage: 12V Humidity: 56% Test Result: Pass Frequency Emission PK/AV Horiz / Limits PK/AV Margin (MHz) (dBuV/m) Vert (dBuV/m) (dB) 315 67.61 Horizontal 95.62/75.62 -28.01 315 60.25 Vertical 95.62/75.62 -35.37 630 43.22 Horizontal 75.62/55.62 -32.40 630 37.97 Vertical 75.62/55.62 -37.65 945 45.72 Horizontal 75.62/55.62 -29.90 945 40.16 Vertical 75.62/55.62 -35.46 Note: the PK value is less than the AV limit value, so there is no necessary to take down the AV value. The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 12 of 32 Date: 2013-03-25 B. General Radiated Emission Data and Harmonics Radiated Emission Data Radiated Emission In Horizontal (30MHz----1000MHz) EUT set Condition: Keep Tx Transmitting Results: Pass Please refer to following diagram for individual Radiated Emission In Vertical (30MHz----1000MHz) Please refer to following diagram for individual The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 13 of 32 Date: 2013-03-25 C. General Radiated Emission Data and Harmonics Radiated Emission Data Radiated Emission In Horizontal (1000MHz----6000MHz) EUT set Condition: Keep Tx Transmitting Results: Pass Please refer to following diagram for individual Frequency (MHz) Level@3m (dBμV/m) Antenna Polarity Limit@3m (dBμV/m) 1269.000 35.07(PK) H 54.00 1575.000 30.17(PK) H 54.00 Note: the PK value is less than the AV limit value, so there is no necessary to take down the AV value. The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 14 of 32 Date: 2013-03-25 C. General Radiated Emission Data and Harmonics Radiated Emission Data Radiated Emission In Vertical (1000MHz----6000MHz) EUT set Condition: Keep Tx Transmitting Results: Pass Please refer to following diagram for individual Frequency (MHz) Level@3m (dBμV/m) Antenna Polarity Limit@3m (dBμV/m) 1260.000 32.46(PK) V 54.00 Note: the PK value is less than the AV limit value, so there is no necessary to take down the AV value. The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 15 of 32 Date: 2013-03-25 7.0 20dB Bandwidth Testing 7.1 Requirement Per 15.231(c), The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. Bandwidth is determined at the points 20 dB down from the modulated carrier. 7.2 Test Procedure With the EUT’s antenna attached, the EUT’s 20dB Bandwidth power was received by the test antenna which was connected to the spectrum analyzer with the START and STOP frequencies set to the EUT’s operation band. 7.3 Test Data Frequency （MHz） 20dB Bandwidth Emission (kHz) Limit (kHz) Result 315 149.4 787.5 Pass Limit=Frequency x 0.25%=315 x 0.25%=787.5kHz Refer to attached plots: The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 16 of 32 Date: 2013-03-25 ndB DOWN VALUE * RBW 30 kHz Marker 1 [T1 ] 20 dB * VBW 10 MHz -29.02 dBm Ref -10 dBm * Att 0 dB SWT 2.5 ms 314.930400000 MHz -10 ndB [T1] 20.00 dB BW 149.400000000 kHz Temp 1 [T1 ndB] A -20 -49.75 dBm 1 PK 1 314.845800000 MHz MAXH -30 Temp 2 [T1 ndB] -49.02 dBm 314.995200000 MHz -40 T1 T2 -50 -60 3DB -70 -80 -90 -100 -110 Center 314.9304 MHz 30 kHz/ Span 300 kHz Date: 20.MAR.2013 12:04:02 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 17 of 32 Date: 2013-03-25 8.0 Deactivate Test 8.1 Requirement Per 15.231(a) (1), a manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. 8. 2 Radiated Test Setup Distance = 3m Computer Pre -Amplifier EUT Turn-table Receiver Ground Plane For the actual test configuration , please refer to the related items – Photos of Testing The deactivation test was performed in the 3 meters chamber B test site, using the setup accordance with the ANSI C63.4 - 2003. The specification used was the FCC 15.231(a) limits. 8.3 Test Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. 8.4 Test Data Refer to attached plots: The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 18 of 32 Date: 2013-03-25 DELTA MARKER 2 RBW 1 MHz Delta 2 [T1 ] 640 ms * VBW 1 MHz 2.56 dB Ref -10 dBm * Att 0 dB SWT 10 s 640.000000 ms -10 Marker 1 [T1 ] -34.65 dBm 4.680000 s A -20 SGL 1 PK MAXH 2 -30 1 -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 314.9304 MHz 1 s/ Date: 20.MAR.2013 12:05:48 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 19 of 32 Date: 2013-03-25 9.0 Duty Cycle 9.1 Limit No dedicated limit specified in the Rules 9.2 Test Procedure 1. Place the EUT on the table and set it in transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set center frequency of spectrum analyzer=operating frequency. 4. Set the spectrum analyzer as RBW, VBW=1MHz, Span=0Hz, Adjust Sweep=200ms. 5. Repeat above procedures until all frequency measured were complete. 9.3 Test Data Base on the worst case Tp = 100 ms Ton1= 2.07*2 = 4.14(ms) Ton2+Ton3= 0.520*98=50.96(ms) (Worse case was considered) Duty cycle=Ton/Tp=0.551 Duty cycle factor = 20 * log (duty cycle) = 20 * log (0.551) = - 5.18dB Note: From the test plot on page 20, we can not get the exact number of Ton2 and Ton3. As the on time of Ton3 is more than the on time of Ton2. So we calculate the duty cycle with Ton3, and it is the worse case. The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 20 of 32 Date: 2013-03-25 Testing Plots: DELTA MARKER 2 RBW 1 MHz Delta 2 [T1 ] 39 ms * VBW 1 MHz -0.76 dB Ref -10 dBm * Att 0 dB SWT 100 ms 39.000000 ms -10 Marker 1 [T1 ] -33.92 dBm 7.800000 ms A -20 SGL 1 PK MAXH -30 1 2 -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 314.9304 MHz 10 ms/ Date: 20.MAR.2013 12:09:01 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 21 of 32 Date: 2013-03-25 DELTA MARKER 2 RBW 1 MHz Delta 2 [T1 ] 39.1 ms * VBW 1 MHz -0.73 dB Ref -10 dBm * Att 0 dB SWT 50 ms 39.100000 ms -10 Marker 1 [T1 ] -32.86 dBm 5.000000 ms A -20 SGL 1 PK MAXH -30 1 2 -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 314.9304 MHz 5 ms/ Date: 20.MAR.2013 12:10:57 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 22 of 32 Date: 2013-03-25 Ton1 DELTA MARKER 2 RBW 1 MHz Delta 2 [T1 ] 2.07 ms * VBW 1 MHz 0.13 dB Ref -10 dBm * Att 0 dB SWT 5 ms 2.070000 ms -10 Marker 1 [T1 ] -35.89 dBm 1.940000 ms A -20 SGL 1 PK MAXH -30 1 2 -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 314.9304 MHz 500 µs/ Date: 20.MAR.2013 12:16:10 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 23 of 32 Date: 2013-03-25 Ton2 DELTA MARKER 2 RBW 1 MHz Delta 2 [T1 ] 230 µs * VBW 1 MHz 1.62 dB Ref -10 dBm * Att 0 dB SWT 5 ms 230.000000 µs -10 Marker 1 [T1 ] -35.74 dBm 3.310000 ms A -20 SGL 1 PK MAXH -30 2 1 -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 314.9304 MHz 500 µs/ Date: 20.MAR.2013 12:15:16 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 24 of 32 Date: 2013-03-25 Ton3 DELTA MARKER 2 RBW 1 MHz Delta 2 [T1 ] 520 µs * VBW 1 MHz 3.13 dB Ref -10 dBm * Att 0 dB SWT 5 ms 520.000000 µs -10 Marker 1 [T1 ] -37.25 dBm 1.470000 ms A -20 SGL 1 PK MAXH -30 2 1 -40 -50 -60 3DB -70 -80 -90 -100 -110 Center 314.9304 MHz 500 µs/ Date: 20.MAR.2013 12:15:39 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 25 of 32 Date: 2013-03-25 10.0 Antenna Requirement 10.1 Standard Applicable An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This requirement does not apply to carrier current devices or to devices operated under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators that must be professionally installed, such as perimeter protection systems and some field disturbance sensors, or to other intentional radiators which, in accordance with Section 15.31(d), must be measured at the installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed so that the limits in this Part are not exceeded. 10.2 Antenna Connected constructions The antenna is PCB Printed antenna which is built-in. So it meets the requirement of 15.203 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 26 of 32 Date: 2013-03-25 11.0 FCC ID Label FCC ID: SJV-2879316 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The label must not be a stick-on paper label. The label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Mark Location: FCC ID Label Location The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 27 of 32 Date: 2013-03-25 12.0. Photo of testing 12.1 Conducted test View—N/A 12.2 Radiated emission test view The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 28 of 32 Date: 2013-03-25 12.3 Photo for the EUT Outside View (Tx) The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 29 of 32 Date: 2013-03-25 Outside View (Tx) The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 30 of 32 Date: 2013-03-25 Inside View (Tx) Inside View (Tx) The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 31 of 32 Date: 2013-03-25 Inside View (Tx) The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.

Report No: 1303001 Page 32 of 32 Date: 2013-03-25 Inside View (Tx) End of the report The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate.


Document Created: 2013-04-03 10:02:04
Document Modified: 2013-04-03 10:02:04
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC