Test report

FCC ID: SIP-5596-V

Test Report

Download: PDF
FCCID_4349421

TEST REPORT Report No…………………………….: CHTEW19060218 Report verification : Project No.……………………..…….: SHT1906018702EW FCC ID ............................................. : SIP-5596-V Applicant’s name ........................... : MegaGain International Ltd. Address ............................................. : Rm 904-905, Greenfield Tower, Concordia Plaza,1 Science Museum Road, T.S.T. East. Kowloon. HongKong Manufacturer....................................: MegaGain International Ltd. Address ............................................. : Rm 904-905, Greenfield Tower, Concordia Plaza,1 Science Museum Road, T.S.T. East. Kowloon. HongKong Test item description .................... : MICKEY RC CAR H20 Trade Mark ....................................... : Disney Model/Type reference ....................... : 5596-V Listed Model(s) ................................. : - Standard ......................................... : FCC CFR Title 47 Part 15 Subpart C Section 15.249 Date of receipt of test sample……….: May 27, 2019 Date of testing………………………...: May 27, 2019- Jun.27, 2019 Date of issue…………………………..: Jun.28, 2019 Result .................. …………………...: PASS Compiled by ( position+printedname+signature) ... : File administrators Echo Wei Supervised by (position+printedname+signature) .... : Project Engineer Jerry Zhao Approved by (position+printedname+signature) .... : RF Manager Hans Hu Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd. Address ............................................. : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Page: 1 of 25

Report No : CHTEW19060218 Page 2 of 25 Issued: 2019-06-28 Contents 1. TEST STANDARDS AND REPORT VERSION 3 1.1. Test Standards 3 1.2. Report version information 3 2. TEST DESCRIPTION 4 3. SUMMARY 5 3.1. Client Information 5 3.2. Product Description 5 3.3. EUT operation mode 6 3.4. EUT configuration 6 3.5. Modifications 6 4. TEST ENVIRONMENT 7 4.1. Address of the test laboratory 7 4.2. Test Facility 7 4.3. Environmental conditions 8 4.4. Statement of the measurement uncertainty 8 4.5. Equipments Used during the Test 9 5. TEST CONDITIONS AND RESULTS 11 5.1. Antenna requirement 11 5.2. AC Power Conducted Emissions 12 5.3. 20 dB Occupied Bandwidth 13 5.4. Radiated field strength of the fundamental signal 15 5.5. Radiated Spurious Emissions and Bandedge Emission 17 6. TEST SETUP PHOTOS OF THE EUT 22 7. EXTERNAL AND INTERNAL PHOTOS OF THE EUT 23 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 3 of 25 Issued: 2019-06-28 1. TEST STANDARDS AND REPORT VERSION 1.1. Test Standards The tests were performed according to following standards: FCC Rules Part 15.249: Operation within the bands 902-928 MHz, 2400-2483.5 MHz, 5725-5875 MHz, and 24.0-24.25 GHz. ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. 1.2. Report version information Revision No. Date of issue Description N/A 2019-06-28 Original Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 4 of 25 Issued: 2019-06-28 2. TEST DESCRIPTION Test Item Section in CFR 47 Result Test Engineer Antenna requirement 15.203 PASS Jiongsheng Feng AC Power Line Conducted Emissions 15.207 N/A N/A 20dB Occupied Bandwidth 15.215/15.249 PASS Jiongsheng Feng Field strength of the Fundamental signal 15.249(a) PASS Shower Dai Spurious Emissions 15.209/15.249(a) PASS Shower Dai Band edge Emissions 15.205/15.249(d) PASS Shower Dai Remark: The measurement uncertainty is not included in the test result. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 5 of 25 Issued: 2019-06-28 3. SUMMARY 3.1. Client Information Applicant: MegaGain International Ltd. Rm 904-905, Greenfield Tower, Concordia Plaza,1 Science Museum Road, Address: T.S.T. East. Kowloon. HongKong Manufacturer: MegaGain International Ltd. Rm 904-905, Greenfield Tower, Concordia Plaza,1 Science Museum Road, Address: T.S.T. East. Kowloon. HongKong 3.2. Product Description Name of EUT: MICKEY RC CAR H20 Trade Mark: Disney Model No.: 5596-V Listed Model(s): - Power supply: DC 4.5V RF Specification Operation frequency: 2411 MHz -2472 MHz Channel number: 20 Modulation Type: GFSK Antenna type: Integral antenna Antenna gain: 0 dBi Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 6 of 25 Issued: 2019-06-28 3.3. EUT operation mode ⚫ Test frequency list According to section 15.31(m), regards to the operating frequency range over 10 MHz, must select three channel which were tested. the Lowest frequency, the middle frequency, and the highest frequency of channel were selected to perform the test, please see the above gray bottom. Channel Frequency (MHz) Channel Frequency (MHz) 00 2411 10 2441 01 2413 11 2443 02 2420 12 2445 03 2422 13 2451 04 2424 14 2453 05 2426 15 2455 06 2428 16 2461 07 2435 17 2468 08 2437 18 2470 09 2439 19 2472 ⚫ TEST MODE For RF test items The engineering test program was provided and enabled to make EUT continuous transmit. For Radiated suprious emissions test item: The engineering test program was provided and enabled to make EUT continuous transmit(duty cycle>98%). The EUT in each of three orthogonal axis emissions had been tested ,but only the worst case (X axis) data Recorded in the report. 3.4. EUT configuration The following peripheral devices and interface cables were connected during the measurement: ● - supplied by the manufacturer ○ - supplied by the lab Manufacturer : / Model No. : / Manufacturer : / Model No. : / 3.5. Modifications No modifications were implemented to meet testing criteria. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 7 of 25 Issued: 2019-06-28 4. TEST ENVIRONMENT 4.1. Address of the test laboratory Laboratory: Shenzhen Huatongwei International Inspection Co., Ltd. Address: 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Phone: 86-755-26748019 Fax: 86-755-26748089 4.2. Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L1225 Shenzhen Huatongwei International Inspection Co., Ltd. has been assessed and proved to be in compliance with CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2005 General Requirements) for the Competence of Testing and Calibration Laboratories. A2LA-Lab Cert. No. 3902.01 Shenzhen Huatongwei International Inspection Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2005 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. FCC-Registration No.: 762235 Shenzhen Huatongwei International Inspection Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the FCC (Federal Communications Commission). The acceptance letter from the FCC is maintained in our files. Registration 762235. IC-Registration No.: 5377B-1 Two 3m Alternate Test Site of Shenzhen Huatongwei International Inspection Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for the performance of radiated measurements with Registration No. 5377B-1. ACA Shenzhen Huatongwei International Inspection Co., Ltd. EMC Laboratory can also perform testing for the Australian C-Tick mark as a result of our A2LA accreditation. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 8 of 25 Issued: 2019-06-28 4.3. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15~35°C Relative Humidity: 30~60 % Air Pressure: 950~1050mba 4.4. Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors in calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report according to TR-100028-01 “Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurement of mobile radio equipment characteristics;Part 1” and TR-100028-02 “Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurementof mobile radio equipment characteristics;Part 2” and is documented in the Shenzhen Huatongwei International Inspection Co., Ltd quality system according to ISO/IEC 17025. Further more, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Here after the best measurement capability for Shenzhen Huatongwei is reported: Test Items Measurement Uncertainty Notes Conducted Disturbance 150kHz~30MHz 3.02 dB (1) Radiated Emissions below 1GHz 4.90 dB (1) Radiated Emissions above 1GHz 4.96 dB (1) Occupied Bandwidth 70 Hz (1) (1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=1.96. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 9 of 25 Issued: 2019-06-28 4.5. Equipments Used during the Test ● Conducted Emission Last Cal. Date Next Cal. Date Used Test Equipment Manufacturer Model No. Serial No. (YY-MM-DD) (YY-MM-DD) ● Shielded Room Albatross projects N/A N/A 2018/09/28 2023/09/27 ● EMI Test Receiver R&S ESCI 101247 2018/10/27 2019/10/26 ● Artificial Mains SCHWARZBECK NNLK 8121 573 2018/10/27 2019/10/26 ● Pulse Limiter R&S ESH3-Z2 100499 2018/10/27 2019/10/26 ● RF Connection Cable HUBER+SUHNER EF400 N/A 2018/11/15 2019/11/14 ● Test Software R&S ES-K1 N/A N/A N/A Single Balanced ○ FCC FCC-TLISN-T2-02 20371 2018/10/28 2019/10/27 Telecom Pair ISN Two Balanced ○ FCC FCC-TLISN-T4-02 20373 2018/10/28 2019/10/27 Telecom Pairs ISN Four Balanced ○ FCC FCC-TLISN-T8-02 20375 2018/10/28 2019/10/27 Telecom Pairs ISN ○ V-Network R&S ESH3-Z6 100211 2018/10/27 2019/10/26 ○ V-Network R&S ESH3-Z6 100210 2018/10/27 2019/10/26 ○ 2-Line V-Network R&S ESH3-Z5 100049 2018/10/27 2019/10/26 ● Radiated Emission-6th test site Last Cal. Date Next Cal. Date Used Test Equipment Manufacturer Model No. Serial No. (YY-MM-DD) (YY-MM-DD) Semi-Anechoic ● Albatross projects SAC-3m-02 N/A 2018/09/30 2021/09/29 Chamber ● EMI Test Receiver R&S ESCI 100900 2018/10/28 2019/10/27 ● Loop Antenna R&S HFH2-Z2 100020 2017/11/20 2020/11/19 Ultra-Broadband ● SCHWARZBECK VULB9163 546 2017/04/05 2020/04/04 Antenna ● Pre-Amplifer SCHWARZBECK BBV 9742 N/A 2018/11/15 2019/11/14 ● RF Connection Cable HUBER+SUHNER N/A N/A 2018/09/28 2019/09/27 ● RF Connection Cable HUBER+SUHNER SUCOFLEX104 501184/4 2018/09/28 2019/09/27 ● Test Software R&S ES-K1 N/A N/A N/A ● Turntable Maturo Germany TT2.0-1T N/A N/A N/A ● Antenna Mast Maturo Germany CAM-4.0-P-12 N/A N/A N/A ● Radiated emission-7th test site Last Cal. Date Next Cal. Date Used Test Equipment Manufacturer Model No. Serial No. (YY-MM-DD) (YY-MM-DD) Semi-Anechoic ● Albatross projects SAC-3m-01 N/A 2018/09/30 2021/09/29 Chamber ● Spectrum Analyzer R&S FSP40 100597 2018/10/27 2019/10/26 ● Horn Antenna SCHWARZBECK 9120D 1011 2017/03/27 2020/03/26 ● Pre-amplifier BONN BLWA0160-2M 1811887 2018/11/14 2019/11/13 ● Pre-amplifier CD PAP-0102 12004 2018/11/14 2019/11/13 Broadband Pre- ● SCHWARZBECK BBV 9718 9718-248 2019/04/26 2020/04/25 amplifier ● RF Connection Cable HUBER+SUHNER RE-7-FH N/A 2018/11/15 2019/11/14 ● RF Connection Cable HUBER+SUHNER RE-7-FL N/A 2018/11/15 2019/11/14 ● Test Software Audix E3 N/A N/A N/A ● Turntable Maturo Germany TT2.0-1T N/A N/A N/A ● Antenna Mast Maturo Germany CAM-4.0-P-12 N/A N/A N/A Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 10 of 25 Issued: 2019-06-28 ● RF Conducted Method Last Cal. Date Next Cal. Date Used Test Equipment Manufacturer Model No. Serial No. (YY-MM-DD) (YY-MM-DD) Signal and spectrum ● R&S FSV40 100048 2018/10/28 2019/10/27 Analyzer ● Spectrum Analyzer Agilent N9020A MY50510187 2018/09/29 2019/09/28 ○ OSP R&S OSP120 101317 N/A N/A Radio communication ○ R&S CMW500 137688-Lv 2018/09/29 2019/09/28 tester ○ Test software Tonscend JS1120-1(LTE) N/A N/A N/A ○ Test software Tonscend JS1120-2(WIFI) N/A N/A N/A ○ Test software Tonscend JS1120-3(WCDMA) N/A N/A N/A ○ Test software Tonscend JS1120-4(GSM) N/A N/A N/A Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 11 of 25 Issued: 2019-06-28 5. TEST CONDITIONS AND RESULTS 5.1. Antenna requirement Requirement FCC CFR Title 47 Part 15 Subpart C Section 15.203: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of anantenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. Refer to statement below for compliance. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. Further, this requirement does not apply to intentional radiators that must be professionally installed. TEST RESULTS Passed Not Applicable The directional gain of the antenna less than 6 dBi, please refer to the below antenna photo. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 12 of 25 Issued: 2019-06-28 5.2. AC Power Conducted Emissions LIMIT FCC CFR Title 47 Part 15 Subpart C Section 15.207: Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. TEST CONFIGURATION TEST PROCEDURE 1. The EUT was setup according to ANSI C63.10:2013 2. The EUT was placed on a plat form of nominal size, 1 m by 1.5 m, raised 10 cm above the conducting ground plane. The vertical conducting plane was located 40 cm to the rear of the EUT. All other surfaces of EUT were at least 10 cm from any other grounded conducting surface. 3. The EUT and simulators are connected to the main power through a line impedance stabilization network (LISN). The LISN provides a 50ohm / 50uH coupling impedance for the measuring equipment. 4. The peripheral devices are also connected to the main power through a LISN. (Please refer to the block diagram of the test setup and photographs) 5. Each current-carrying conductor of the EUT power cord, except the ground (safety) conductor,was individually connected through a LISN to the input power source. 6. The excess length of the power cord between the EUT and the LISN receptacle were folded back and forth at the center of the lead to form a bundle not exceeding 40 cm in length. 7. Conducted emissions were investigated over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9 kHz. 8. During the above scans, the emissions were maximized by cable manipulation. TEST MODE: Please refer to the clause 3.3 TEST RESULTS Passed Not Applicable Note: The EUT is DC supply, so this item is not applicable. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 13 of 25 Issued: 2019-06-28 5.3. 20 dB Occupied Bandwidth Limit Operation frequency range 2400MHz~2483.5MHz. TEST CONFIGURATION TEST PROCEDURE 1. The transmitter output was connected to the spectrum analyzer through an attenuator, the path loss was compensated to the results for each measurement. 2. Set to the maximum power setting and enable the EUT transmit continuously 3. Use the following spectrum analyzer settings: Span = approximately 2 to 3 times the 20 dB bandwidth, centered on a hopping channel RBW ≥ 1% of the 20 dB bandwidth, VBW ≥ RBW Sweep = auto, Detector function = peak, Trace = max hold 4. Measure and record the results in the test report. TEST MODE: Please refer to the clause 3.3 TEST RESULTS Passed Not Applicable 20dB Bandwidth Limit Test Channel Result (MHz) (MHz) CHL 6.40 - Pass CHM 5.76 - Pass CHH 4.36 - Pass Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 14 of 25 Issued: 2019-06-28 CHL D ate:19.JUN.2019 16:55:43 CHM D ate:19.JUN.2019 16:56:59 CHH D ate:19.JUN.2019 17:00:07 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 15 of 25 Issued: 2019-06-28 5.4. Radiated field strength of the fundamental signal LIMIT Field strength of fundamental Field strength of harmonics Fundamental frequency (millivolts/meter) (microvolts/meter) 902-928 MHz 50 (94dBuV/m @3m) 500 (54dBuV/m @3m) 2400-2483.5 MHz 50 (94dBuV/m @3m) 500 (54dBuV/m @3m) 5725-5875 MHz 50 (94dBuV/m @3m) 500 (54dBuV/m @3m) 24.0-24.25 GHz 250 (108dBuV/m @3m) 2500 (68dBuV/m @3m) Frequencies above 1000 MHz, the field strength limits are based on average limits TEST CONFIGURATION TEST PROCEDURE 1. The EUT was setup and tested according to ANSI C63.10:2013 requirements. 2. The EUT is placed on a turn table which is 1.5 meter above ground. The turn table is rotated 360 degrees to determine the position of the maximum emission level. 3. The EUT waspositioned such that the distance from antenna to the EUT was 3 meters. 4. The antenna is scanned from 1 meter to 4 meters to find out the maximum emission level. Thisis repeated for both horizontal and vertical polarization of the antenna. In order to find the maximum emission, all of the interface cables were manipulated according to ANSI C63.10:2013 on radiated measurement. 5. The receiver set as follow: RBW=1MHz, VBW=3MHz Peak detector for Peak value. RBW=1MHz, VBW=3MHz RMS detector for Average value. TEST MODE: Please refer to the clause 3.3 TEST RESULTS Passed Not Applicable Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 16 of 25 Issued: 2019-06-28 CHL Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2411.08 50.99 32.03 13.13 0.00 96.15 114.00 -17.85 Vertical Peak 2411.06 51.22 32.03 13.13 0.00 96.38 114.00 -17.62 Horizontal Peak 2410.80 50.89 27.56 13.13 0.00 91.58 94.00 -2.42 Vertical Average 2410.86 49.07 27.56 13.13 0.00 89.76 94.00 -4.24 Horizontal Average CHM Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2441.10 51.54 32.23 13.22 0.00 96.99 114.00 -17.01 Vertical Peak 2441.02 50.60 32.23 13.22 0.00 96.05 114.00 -17.95 Horizontal Peak 2441.10 50.99 27.43 13.22 0.00 91.64 94.00 -2.36 Vertical Average 2441.14 49.34 27.43 13.22 0.00 89.99 94.00 -4.01 Horizontal Average CHH Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2472.04 50.67 32.51 13.32 0.00 96.50 114.00 -17.50 Vertical Peak 2472.06 50.15 32.51 13.32 0.00 95.98 114.00 -18.02 Horizontal Peak 2472.08 50.40 27.31 13.32 0.00 91.03 94.00 -2.97 Vertical Average 2472.06 49.60 27.31 13.32 0.00 90.23 94.00 -3.77 Horizontal Average Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 17 of 25 Issued: 2019-06-28 5.5. Radiated Spurious Emissions and Bandedge Emission LIMIT FCC CFR Title 47 Part 15 Subpart C Section 15.209 Frequency Limit (dBuV/m @3m) Value 30MHz~88MHz 40.00 Quasi-peak 88MHz~216MHz 43.50 Quasi-peak 216MHz~960MHz 46.00 Quasi-peak 960MHz~1GHz 54.00 Quasi-peak 54.00 Average Above 1GHz 74.00 Peak TEST CONFIGURATION ⚫ 9 kHz ~ 30 MHz ⚫ 30 MHz ~ 1 GHz ⚫ Above 1 GHz Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 18 of 25 Issued: 2019-06-28 TEST PROCEDURE 1. The EUT was setup and tested according to ANSI C63.10:2013 requirements. 2. The EUT is placed on a turn table which is 0.8 meter above ground for below 1 GHz, and 1.5 m for above 1 GHz. The turn table is rotated 360 degrees to determine the position of the maximum emission level. 3. The EUT was set 3 meters from the receiving antenna, which was mounted on the top of a variable height antenna tower. 4. For each suspected emission, the EUT was arranged to its worst case and then tune the Antenna tower (from 1 m to 4 m) and turntable (from 0 degree to 360 degrees) to find the maximum reading. A pre-amp and a high pass filter are used for the test in order to get better signal level to comply with the guidelines. 5. Set to the maximum power setting and enable the EUT transmit continuously. 6. Use the following spectrum analyzer settings (1) Span shall wide enough to fully capture the emission being measured; (2) Below 1 GHz: RBW=120 kHz, VBW=300 kHz, Sweep=auto, Detector function=peak, Trace=max hold; If the emission level of the EUT measured by the peak detector is 3 dB lower than the applicable limit, the peak emission level will be reported. Otherwise, the emission measurement will be repeated using the quasi-peak detector and reported. (3) From 1 GHz to 10th harmonic: RBW=1MHz, VBW=3MHz Peak detector for Peak value. RBW=1MHz, VBW=3MHz RMS detector for Average value. TEST MODE: Please refer to the clause 3.3 TEST RESULTS Passed Not Applicable Note: 1) Above 1GHz Final Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor 2) The emission levels of other frequencies are very lower than the limit and not show in test report. Radiated Spurious Emissions ◼ 9 kHz ~ 30 MHz The EUT was pre-scanned the frequency band (9 kHz ~ 30 MHz), found the radiated level lower than the limit, so don’t show on the report. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 19 of 25 Issued: 2019-06-28 ◼ 30 MHz ~ 1 GHz Polarization: Vertical Polarization: Horizontal Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 20 of 25 Issued: 2019-06-28 ◼ Above 1 GHz Test channel CHL Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2789.46 33.28 28.10 8.90 34.87 35.41 74.00 -38.59 Vertical Peak 5164.81 31.90 31.64 12.05 34.79 40.80 74.00 -33.20 Vertical Peak 6611.33 31.37 34.20 14.08 35.10 44.55 74.00 -29.45 Vertical Peak 9228.06 32.06 38.77 15.94 35.95 50.82 74.00 -23.18 Vertical Peak 2825.19 32.62 28.20 8.91 35.61 34.12 74.00 -39.88 Horizontal Peak 5217.66 31.25 31.46 12.11 34.69 40.13 74.00 -33.87 Horizontal Peak 6696.01 30.80 34.20 14.19 34.93 44.26 74.00 -29.74 Horizontal Peak 8549.59 31.26 37.10 15.91 34.36 49.91 74.00 -24.09 Horizontal Peak Test channel CHM Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2920.25 34.97 28.52 8.86 37.14 35.21 74.00 -38.79 Vertical Peak 4883.52 35.10 31.43 11.68 35.97 42.24 74.00 -31.76 Vertical Peak 7301.36 31.31 36.30 14.54 34.79 47.36 74.00 -26.64 Vertical Peak 8792.37 31.41 37.72 15.98 34.80 50.31 74.00 -23.69 Vertical Peak 3208.66 34.42 28.75 9.46 37.34 35.29 74.00 -38.71 Horizontal Peak 4883.52 37.47 31.43 11.68 35.97 44.61 74.00 -29.39 Horizontal Peak 5125.52 32.79 31.80 12.04 35.02 41.61 74.00 -32.39 Horizontal Peak 8637.08 31.61 37.52 15.94 34.52 50.55 74.00 -23.45 Horizontal Peak Test channel CHH Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2818.01 33.60 28.17 8.92 35.42 35.27 74.00 -38.73 Vertical Peak 5060.69 31.23 31.74 12.02 35.30 39.69 74.00 -34.31 Vertical Peak 7099.75 31.52 35.60 14.51 34.68 46.95 74.00 -27.05 Vertical Peak 8927.68 31.98 37.83 16.01 35.04 50.78 74.00 -23.22 Vertical Peak 3120.06 34.71 28.80 9.22 37.73 35.00 74.00 -39.00 Horizontal Peak 4946.07 31.99 31.45 11.78 35.73 39.49 74.00 -34.51 Horizontal Peak 7624.25 31.28 36.18 15.04 34.20 48.30 74.00 -25.70 Horizontal Peak 9111.35 32.11 38.25 15.99 35.55 50.80 74.00 -23.20 Horizontal Peak Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor 2. The peak level is lower than average limit(54dBuV/m), this data is the too weak instrument of signal is unable to test. 3. The emission levels of other frequencies are very lower than the limit and not show in test report. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 21 of 25 Issued: 2019-06-28 Bandedge Emission Test channel CHL Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2310.00 10.78 28.05 7.73 0.00 46.56 54.00 -7.44 Horizontal Average 2480.02 10.38 27.65 7.84 0.00 45.87 54.00 -8.13 Horizontal Average 2310.00 13.89 28.05 7.73 0.00 49.67 74.00 -24.33 Horizontal Peak 2480.02 15.97 27.65 7.84 0.00 51.46 74.00 -22.54 Horizontal Peak 2310.00 10.80 28.05 7.73 0.00 46.58 54.00 -7.42 Vertical Average 2480.02 10.32 27.65 7.84 0.00 45.81 54.00 -8.19 Vertical Average 2310.00 14.32 28.05 7.73 0.00 50.10 74.00 -23.90 Vertical Peak 2480.02 13.44 27.65 7.84 0.00 48.93 74.00 -25.07 Vertical Peak Test channel CHH Read Antenna Cable Preamp Over Frequency Level Limit Line Test Level Factor Loss Factor Limit Polarization (MHz) (dBuV/m) (dBuV/m) value (dBuV) (dB/m) (dB) (dB) (dB) 2483.51 10.26 27.26 8.04 0.00 45.56 54.00 -8.44 Horizontal Average 2500.00 10.24 27.20 8.08 0.00 45.52 54.00 -8.48 Horizontal Average 2483.51 14.30 27.26 8.04 0.00 49.60 74.00 -24.40 Horizontal Peak 2500.00 13.99 27.20 8.08 0.00 49.27 74.00 -24.73 Horizontal Peak 2483.51 10.24 27.26 8.04 0.00 45.54 54.00 -8.46 Vertical Average 2500.00 10.24 27.20 8.08 0.00 45.52 54.00 -8.48 Vertical Average 2483.51 14.01 27.26 8.04 0.00 49.31 74.00 -24.69 Vertical Peak 2500.00 13.25 27.20 8.08 0.00 48.53 74.00 -25.47 Vertical Peak Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss – Preamplifier Factor 2. The peak level is lower than average limit(54dBuV/m), this data is the too weak instrument of signal is unable to test. 3. The emission levels of other frequencies are very lower than the limit and not show in test report. Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 22 of 25 Issued: 2019-06-28 6. TEST SETUP PHOTOS OF THE EUT Radiated Emissions Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 23 of 25 Issued: 2019-06-28 7. EXTERNAL AND INTERNAL PHOTOS OF THE EUT External Photos Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 24 of 25 Issued: 2019-06-28 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)

Report No : CHTEW19060218 Page 25 of 25 Issued: 2019-06-28 Internal Photos --------End of Report-------- Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V01 (2018-01)


Document Created: 2019-07-08 20:46:47
Document Modified: 2019-07-08 20:46:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC